Hotpoint Freezer FFS70 User manual

Brand: Hotpoint

Model: Freezer FFS70

Category: Combi-fridges

Type: User manual

This manual is also suitable for

FRIDGE FREEZER - MODELS FFA80, FFA70, FFS70 & FFA60

INSTRUCTIONS FOR INSTALLATION & USE

GETTING STARTED:

To ensure that your fridge freezer runs reliably and efficiently follow these steps.

SAFETY &

INSTALLATION CONTROLS

USEFUL ADVICE

CLEANING &

MAINTENANCE

SERVICE &

GUARANTEE

TROUBLESHOOTING

Read the rest of these instructions to get the best from your appliance

and remember to fill in your guarantee registration.

Keep this Book in a safe place for quick reference.

Choose a location for your

fridge freezer, away from

any heat sources and

allow adequate

ventilation - 100mm

(4 inch) gap above.

Level the fridge freezer by

adjusting the front feet.

This will stop rocking or

vibration and keep the

door aligned.

Before plugging in and

switching on, leave the

fridge freezer in its final

location for at least 15

minutes to allow it to

settle.

If you are freezing fresh

food, turn on fast freeze

by pressing the switch 24

hours before placing the

food inside.

Place the fresh food

inside.

Move the fridge freezer

into position, using the

sides of the cabinet.

Take care to avoid

damaging the refrigerant

circuit pipe work on the

rear.

Plug in and switch on.

Allow the fridge freezer to

cool before placing food

inside.

The high temperature

light will stay on until the

fridge freezer has cooled

down.

All food in the fridge

freezer should be

covered.

STEP 1

STEP 2

After the front feet have

been adjusted and the

fridge freezer is level fit

the left and right hand

bottom hinge covers

supplied.

Align with the cover plate

slots and push into

position.

STEP 4

STEP 3

STEP 5

STEP 6

STEP 7

Your fridge freezer is now

working.

If after 24 hours your

fridge freezer is not

operating as you want,

refer to the

Troubleshooting section.

STEP 8

NB.The spanner is for illustration

only and is not supplied with the

fridge freezer.

Remember to turn fast freeze off

after 24 hours, however if you

forget to do so it will automatically

cancel after 48 hours.

For Your Safety

For your safety, read the following advice:

The fridge freezer cooling system contains a small amount of gas which is

environmentally friendly but flammable. To avoid any risk :-

● Install the fridge freezer following the installation instructions and ensure

that ventilation openings are kept clear of obstruction.

● Take care when installing or moving the fridge freezer to avoid damaging

the pipes on the rear.

● If you suspect a leak, do not switch on the fridge freezer, but open the

windows and doors to ventilate the room.

● Do not use any electrical devices inside the freezer, for instance for

defrosting.

● Do not use any mechanical devices for defrosting other than any which may

have been supplied with the freezer as they may cause damage.

● Only use this fridge freezer for storing domestic foodstuffs.

When installing your fridge freezer :-

● Ensure that the mains cable is not trapped underneath or behind the fridge

freezer when you install or move it.

● Do not stack any other appliance on top of this fridge freezer as they may

damage the fridge or become unstable.

When using your fridge freezer :-

● Do not sit or stand on top of your fridge freezer.

● Do not store poisonous, flammable or dangerous substances in your fridge

freezer.

● Do not use aerosol sprays for defrosting or cleaning your fridge freezer.

If you sell the fridge freezer, pass on this booklet to the new owner.

SAFETY &

INSTALLATION

Installation

Location & Air Circulation

Locate your fridge freezer away from sources of heat e.g.

cookers, radiators, direct sunlight as extreme temperature

will affect its performance.

Allow a minimum 100mm (4 inches) between the top of

the fridge freezer and the ceiling or the underside of a

wall cupboard.

Providing you follow the recommended ventilation

requirements you will :-

● Prolong the life of the fridge freezer.

● Minimise the risk of condensation on the outside of

the fridge freezer.

● Minimise the running costs.

● Minimise operating sounds caused by vibration.

Minimum space required to open door

The fridge freezer needs a space of 600mm (24 inches) in front to allow the door

to open.

When positioning the fridge freezer next to a unit, a gap of 30mm (1

inch) can

be left at the hinge side of the door to allow the easy removal of furniture. If

preferred the fridge freezer can be positioned so that a gap is not left.This will

restrict how far the door can be opened but the furniture can still be removed

(see diagrams below).The door hinge side can be changed to make it easier to

open (see ‘Door Reversal’ in the CLEANING & MAINTENANCE section).

SAFETY &

INSTALLATION

100mm

(4 inches)

TOP VIEW

less than 30mm

30mm or more

600mm

Installation

Levelling:

Level the fridge freezer when it is in its final location by adjusting the front feet, until

firm contact is made with the floor. This will stop rocking or vibration and keep the

door aligned which helps the fridge freezer run reliably and efficiently.

Note: Before plugging in and switching on, leave the fridge freezer standing

in its final location for at least 15 minutes to allow it to settle.

Hinge Cover Mouldings:

After the front feet have been adjusted and the fridge freezer is level, fit the left and

right hand bottom hinge covers supplied.

To fit:

SAFETY &

INSTALLATION

Align the bottom hinge cover onto the

cover plate slots.

Push until the bottom hinge cover

clicks into place.

Installation

Electrical Supply

WARNING: This appliance must be earthed.

The appliance must be positioned so that the plug is accessible after

installation.

Fuses

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the

fuse, only use those rated at 13A and ASTA approved to BS1362.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING: To avoid a shock hazard do not insert the discarded plug into a socket

anywhere else.

IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE

FOLLOWING CODE :

Green/Yellow - Earth

Blue - Neutral Brown - Live

If you change the plug, the colour of wires in the mains lead may not correspond with

the colour of the markings identifying terminals in the plug. You should therefore

wire it as shown above.

Changing the Mains Lead

This appliance is fitted with a special mains lead. If you need to replace the mains

lead due to damage, one can be bought from Hotpoint Service (see KEY CONTACTS,

back page).

It is strongly advised that this work is carried out by a qualified electrician.

CE Marking certifies that this appliance conforms to the following EEC

directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC

Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC

SAFETY &

INSTALLATION

Controls

The left hand control wheel on the front panel

adjusts the internal fridge compartment

temperature.

The internal temperature should be 5˚C or colder although some sections such as the

salad bin will be slightly warmer.

The setting of the control wheel will depend on the location of the fridge freezer, the

room temperature and how often the door is opened. The normal set point (marked

by a 3 on the dial) is usually suitable. If you need to adjust the temperature turn the

control wheel using a coin to avoid damage:

Clockwise (higher number) - Colder

Anti-clockwise (lower number) - Warmer

You can check the temperature of the fridge freezer compartments by using a Fridge

Freezer Thermometer available from Hotpoint Genuine Parts and Accessories Mail

Order Hotline (see KEY CONTACTS back page).

WARNING: Do not use a mercury filled thermometer, as breakage would cause a

health hazard.

Your fridge freezer must NOT be placed in a room where the temperature goes below

6˚C or above 38˚C for prolonged periods, as the internal fridge temperature will not

be maintained.

CONTROLS

The right hand control wheel on the front panel

adjusts the internal freezer compartment

temperature.

The internal temperature should be -18˚C or

colder.

The setting of the control wheel will depend on the location of the fridge freezer, the

room temperature and how often the door is opened. The normal set point (marked

by a 3 on the dial) is usually suitable. If you need to adjust the temperature turn the

control wheel using a coin to avoid damage:

Clockwise (higher number) - Colder

Anti-clockwise (lower number) - Warmer

Controlling the Temperature of the Fridge Compartment

Controlling the Temperature of the Freezer Compartment

FFA70 illustrated

Controls

CONTROLS

Indicator Lights

There are two amber lights which indicate functions are selected:

● The amber fast freeze light indicates that the fast freeze button has been

pressed on. By pressing this button ON, the freezer motor will run continuously

for extra cooling.

● The amber holiday light (Models FFA80, FFA70 & FFS70 only) indicates that the

holiday mode is set.

There are two red lights which warn of a rise in temperature in the freezer

compartment:

● The red high temperature warning light will come on when the fridge freezer is

first switched on or when the temperature inside the compartment rises above

the correct storage temperature. It will go out as soon as the compartment

returns to its normal storage temperature.

The red light may come on for a short period when opening the freezer door to

load or unload food, in this case storage times will not be affected.

If there has been a power cut resulting in a rise in freezer compartment

temperature, the red high temperature warning light will come on as soon as the

mains power returns. It will go out as soon as the compartment returns to its

normal storage temperature.

Avoid opening compartment doors during a power cut, the freezer insulation will

continue to protect your food. However if the power cut continues,there is a risk of your

frozen food beginning to defrost due to the rise in temperature.

● The red food defrost alert light (Models FFA80, FFA70 & FFS70 only) will also

come on when the mains power is restored to warn there has been a power cut

and the freezer compartment temperature has risen to an unsafe level allowing

partial defrosting of stored food. If this light is ON, food should be either cooked

and eaten within 24 hours, cooked and refrozen or thrown away.

The red food defrost alert light is a particularly useful warning light if you were

out at the time of the power cut. The light will remain on until cancelled. It can

only be cancelled by pressing the button alongside it.

Check the TROUBLESHOOTING section if you have any problems with these indicator

lights.

FFA70 illustrated

Controls

CONTROLS

Fast Freeze Button - Freezing Fresh Food

The bottom compartment drawer should be used to freeze fresh food.

Transfer already frozen food to one of the upper drawers.

- Before loading 2kg or more of fresh food select fast freeze for the required

pre-freeze time (see chart below).

- If freezing up to 2kg of fresh food just select fast freeze when loading.

Once the fresh food is loaded leave fast freeze on for 24 hours to freeze the food as

quickly as possible.

Maximum freezing capacity 24 hours: FFA70/FFS70 12kg

FFA80/FFA60 8kg

Note : Don’t forget to turn fast freeze off after 24 hours from the introduction of

fresh food to be frozen.

However fast freeze will turn off automatically after 48 hours if you do forget.

Pre-Freeze chart when selecting Fast Freeze:

Load for freezing Pre-freeze time Load position

8 to 12kg max. 24 hours In the bottom drawer.

6 to 8kg max. 24 hours

6 to 8kg 12 hours In the bottom drawer.

2 to 6kg 12 hours

In the bottom drawer.

2 to 6kg 6 hours

up to 2kg not required In the bottom drawer.

Model

FFA70

FFS70

FFA60

FFA80

FFA70

FFS70

FFA60

FFA80

FFA70

FFS70

FFA70

FFS70

FFA60

FFA80

Controls

CONTROLS

Holiday Function (Models FFA80, FFA70/FFS70 only)

This feature allows you to set your fridge compartment to a warmer setting while you

are away on holiday, to reduce running costs without affecting the freezer.

To set up holiday mode:

1. Remove any food, from the fridge compartment, that will deteriorate while you

are away. Make sure the fridge is clean.

2. Close the door.

3. Press the holiday button and the amber holiday indicator light will show that

holiday mode is set.

To reset to normal operation:

1. Press the holiday button OR open the fridge door. The amber holiday indicator

light will go out to show holiday mode is cancelled.

2. The fridge compartment will return to the temperature set on the fridge

temperature control wheel.

Note : Opening the door or pressing the holiday button at any time after holiday

mode has been set will turn the function off. The holiday button works

independently of the fridge temperature control wheel.

Useful Advice

Note:

The Rating Plate, which lists the appliance

Model Number and Serial Number can be

found near the bottom of fridge

compartment on the interior wall.

Fast Freeze

Models: FFA70 / FFS70

Fast Freeze

Model: FFA60

USEFUL ADVICE

Fast Freeze

Model: FFA80

Useful Advice

Making the best use of your Fridge Freezer

To ensure that your fridge freezer operates as efficiently as possible :

● Follow food packaging “best before/use by” instructions or your suppliers

advice on a suitable maximum storage time.

● Keep foods tightly covered to retain moisture and prevent flavour/odour

transference. Plastic bags, aluminium foil, plastic stretch wrap and containers

with lids are ideal.

● Select chilled and frozen food last when shopping, transport in a ‘cool bag’

and place in freezer as soon as possible after arriving home.

● Avoid opening the doors unnecessarily or for longer than needed.

● Allow hot or warm food to cool down in covered containers before placing in

the fridge or freezer, as placing hot food inside reduces efficiency.

● Prepare fresh foods for freezing in small quantities to ensure that the food

freezes quickly and so that its quality does not deteriorate.

● Ensure that packets/containers of food are dry before freezing otherwise

they may freeze together.

Storing Food in a Fridge

● Pack and store cooked and fresh food separately.

● Wrap raw or defrosting meat and poultry in polythene or foil and store

below cooked foods and dairy products to avoid contamination of dripping

food juices.

● Wrap cheese in greaseproof paper and place in an airtight container or

polythene bag.

Bring to room temperature before consuming.

● Empty left over canned food into a covered storage containers before

placing in the fridge.

● Position food to allow cold air to circulate freely, ensuring nothing comes

into contact with the back of the fridge compartment, or covers the defrost

gutter drain hole below this.

● Use the different storage zones inside your fridge compartment to store a

wide variety of food items.

STORAGE ZONES

Zone Type Food Storage

A Cool Dairy products, Cheese, butter, margarine,

Low fat spreads, cooking fats / lards

Preserves - Jam, curd, marmalade,

spread, salad dressing or sauces.

B Colder General food storage

C Coldest Meat fish & poultry

Pre-cooked / chilled food

D Salad Bins Vegetables, fruit and salad items

(Not recommended for the storage of

bananas or onions).

USEFUL ADVICE

Useful Advice

Advice on Adjusting Shelves

Make the most of the interior storage

space by repositioning shelves to suit the

various heights of individual items you

wish to store.

Note : Only the front half of the

shelf can be repositioned, the back

half must remain in its original

position.

Split glass shelf

The split shelf can be used as a standard shelf but also as

two half shelves.

The front half can be repositioned above or below to

enable storage of larger items.

To remove, ensure that the door is open fully.

Slide the shelf forward and tilt from position.

Egg Rack

The egg rack can be used in conjunction with any commodity rack and is easily

removed for cleaning.

Note: Wipe, don’t wash eggs.

Commodity and Bottle Racks

Commodity racks can be repositioned in the door to suit your storage requirements.

The lidded commodity rack is recommended for the storage of dairy items, such as

butter, margarine and cheese.

To remove, lift rack vertically to release from fixing supports. To replace, align grooves

on either side of the rack above fixing supports and push down until secure.

In order to get the best results from the bottle retainer it is advised that it be

positioned centrally on the bottle rack.

USEFUL ADVICE

Useful Advice

Salad Bins

For the storage of fruit, vegetables and salad items.

When storing vegetables, remove unusable leaves and soil. Leave lettuce, cabbage

and cauliflower on the stem.

It is advisable to clean the salad bin regularly, it can be removed by sliding it out from

position.

Note : Care must be taken to ensure that the salad bin is pushed in fully before

shutting the fridge door.

Wine Rack (Models FFA80, FFA70 and FFS70 only)

The wine rack is suitable for cans, wine bottles and 2 litre bottles. The maximum load

recommended is three 2 litre bottles and two wine bottles.

Position the wine rack in the second runner down from the top of the fridge when

storing longer length bottles. This will ensure the bottles clear the door furniture and

allow the door to close properly.

To remove:

Ensure that the fridge door is fully open. Slide the wine

rack forward and tilt from position.

Note: DO NOT remove a fully loaded wine rack, just remove bottles as necessary.

Microban® is a unique antibacterial technology which is built into interior

components of your fridge during manufacture. Microban® protects against growth

of potentially harmful and odour causing bacteria on the interior fridge surfaces,

thereby keeping your fridge fresher and more hygienically clean during use.

Microban® will not wash out or wear out and will provide continuous protection

against bacteria for the life of your fridge. Microban® technology has been proven

safe, durable and effective over many years of use in personal care and household

consumer products. In addition, Hotpoint operate a rigorous antibacterial testing

programme through approved independent testing laboratories.

Note : You should continue to clean your fridge as recommended (see

CLEANING & MAINTENANCE section). Microban® provides an extra level of

hygiene protection in your fridge in between cleanings.

(Model FFS70 only):

USEFUL ADVICE

Useful Advice

Storing Food in a Freezer

● Freeze and store either fresh food or long term

commercially frozen foods.

● Generally speaking long term storage means up to 3

months but this can vary, so always follow your

supplier’s recommendations otherwise refer to the

pictorial guide on the door liner (as shown).

● Place frozen food in the freezer compartment as soon

as possible after buying it.

● Liquid-filled bottles or sealed fizzy drinks must not be

stored in freezer, as they may burst.

● Lollipops and water ices should not be given to children directly from the freezer

the low temperature may cause ‘freezer burns’.

● Store ice cream towards the top front of the freezer and remove from freezer

15-30 minutes before serving.

● Ensure food is labelled and dated before placing in freezer.

● When freezing fresh food follow the instructions for using fast freeze (see

CONTROLS section).

● Do not allow fresh food to come into contact with food already frozen, the

frozen food could start to defrost.

● Once thawed, food should be cooked and eaten within 24 hours or cooked and

refrozen.

STORAGE GUIDE

FFA80/FFA60 FFA/FFS70

Frozen Food

Storage Capacity 23kg 35kg

Maximum Freezing

Capacity in 24 hours 8kg 12kg

Maximum Conservation

Time from Failure 14 hours 14 hours

USEFUL ADVICE

Useful Advice

Advice on Using Freezer Drawers

The freezer compartments must be used with the drawers.

The storage drawers can be easily removed. Pull the drawer towards you until it

reaches it’s stop position. Hold securely on both sides, lift the front of the drawer to

release and remove. For cleaning advice see CLEANING & MAINTENANCE section.

Ensure that the frozen food storage drawers are pushed back fully before closing the

door.

Food can be separated into different storage drawers for easy identification.

When lifting or removing the large deep drawer it is important to hold the side

handles and not the front handle.

WARNING: The freezer drawers can become heavy when fully loaded with food. Care

must be taken if attempting to lift or carry a full freezer drawer. It is recommended to

remove the required food, rather than the whole freezer drawer.

Note : It is important not to touch or move any of the freezer drawers/parts

with wet hands as it may cause freezer burn or discomfort.

Ice Tray

When making ice, always use the tray with the lid provided. Take care not to overfill

with water.

Uncovered food should not be placed near the ice tray as it can affect the flavour of

the ice.

Note : Empty, wash and refill the ice tray periodically to ensure freshness..

USEFUL ADVICE

Defrosting

Fridge compartment

No manual defrosting required

The fridge compartment will defrost automatically. During defrost periods water

droplets form on the interior back wall of your Fridge and refreeze afterwards.

WARNING: Ensure that stored food does not come into contact with the interior

back wall of your Fridge. Also ensure the defrost gutter drain hole is kept clear

see ‘Cleaning’ in the CLEANING & MAINTENANCE section.

Freezer compartment

Frost Free

How Frost Free works

The frost free system completely eliminates the need for defrosting.

A fan circulates air around the freezer. This helps to remove moisture from the

compartment, therefore preventing the build up of ice.

It is normal to hear the fan when the freezer is cooling.

Additional benefits of the frost free system include:

● More even temperatures throughout the freezer.

● Faster cooling times.

CLEANING &

MAINTENANCE

Cleaning

WARNING: Switch off electrical supply and pull out mains plug before cleaning.

Interior

Note : We recommend you use a straw to keep the defrost gutter drain hole

clear of any blockage.DO NOT use sharp metal tools which could cause

damage beyond repair.

WARNING: Do not use abrasive powder, household cleaner, bleach or wax polish

to clean the interior, they will leave a smell in the fridge freezer.

1. Remove stored food, wrap or cover it and place into insulated containers to

keep cool/frozen whilst cleaning.

2. Remove salad bins, racks, shelves and drawers from each compartment.

Wash in warm water and washing up liquid using a soft cloth, dry

thoroughly.

DO NOT use any cleaning agents on the wine rack, just wipe with a soft

cloth.

3. Wipe interiors and fittings with a clean cloth wrung out in a solution of

either one teaspoon of bicarbonate of soda to one pint of water or Milton™

sterilising fluid, diluted according to the manufacturer’s instructions.

4. Dry interior compartments thoroughly with a clean cloth before replacing

fittings and food.

Note : It is important to ensure that cleaned shelves, racks, drawers and

bins are thoroughly dried before refitting into the fridge freezer

compartments.

Exterior

WARNING: Do not use abrasive powder, household cleaner or bleach, they can

damage the exterior of your fridge freezer.

1. Use a clean soft cloth wrung out in warm water and washing up liquid to

wipe the exterior surface, dry thoroughly.

2. Use a soft brush or vacuum cleaner to remove dust from underneath the

fridge freezer and from the compressor and condenser situated at the back

of the fridge freezer.

WARNING: Do not damage the pipework.

Door Seals

Use warm water and a clean soft cloth to wipe along and in between the creases of

the door seals, dry thoroughly. Take care not to damage the seals and avoid using

sharp objects.

WARNING: Do not use detergent, it will damage the seals.

CLEANING &

MAINTENANCE

Going Away

If you are going away and don’t want to use your fridge freezer, switch off electricity

supply and pull out the mains plug. Remove food and follow the cleaning

instructions on the previous page.

Note : Leave the doors ajar to prevent an accumulation of odours.

Changing the Light Bulb

WARNING: Switch off electricity supply and pull out the mains plug

Obtain a replacement SES 15 watt bulb from the Hotpoint Genuine Parts and

Accessories Mail Order Hotline (see KEY CONTACTS back page) and fit as follows :

1. Remove any shelves from directly below the interior light, to make access

easier.

2. Squeeze the side of the lamp guard lightly to unclip. Remove and retain.

3. Remove old bulb and fit new one.

4. Refit lamp guard.

5. Plug in and switch on electrical supply.

Maintenance

Models FFA80, FFA70 & FFS70 only: Alternatively, if you want to keep your freezer

running but want to empty the fridge you could set the holiday mode.

See CONTROLS section.

CLEANING &

MAINTENANCE

Door Reversal

You will need a cross head screwdriver, a flat blade screwdriver and a 5mm spanner to

carry out this procedure.

Our Service Department can arrange for an Engineer to do the conversion for you but

a charge will be made.

WARNING: Switch off electrical supply and pull out the mains plug.

Remove all door furniture and all loose items/fittings from inside the fridge freezer.

If you have previously set up and used the fridge freezer and since decided to reverse

the doors, you must remove stored food, wrap or cover it and place into insulated

containers to keep cool/frozen whilst carrying out this operation.

Remove Top Door

1. Open the door as wide as possible.

Note : You may require assistance to do this:

2. Support the door and using a screwdriver, remove the screw

securing the top hinge.

3. Lower the top hinge and carefully tilt the door to remove the

top hinge from the cabinet. Lift the door off the centre hinge.

4. Remove the top hinge from the door.

Remove Lower Door

Note : You may require assistance to do this:

5. Open the lower door and while supporting the door, remove the spacing

washers and pin from the centre bracket.

Note which way up the pin is fitted.

6. Lift the door off the bottom hinge.

7. Take the two screw

covers off the centre

hinge.

8. Unscrew the two

screws to remove the

centre hinge.

9. Using a flat blade

screwdriver or a 5mm

spanner, remove the

bottom hinge pin,

complete with spacing

washers, from the right

hand hinge bracket.

10. Take the plastic cap

from the left hand

cover plate and use it

to fill the hole on the

right hand cover plate.

CLEANING &

MAINTENANCE

Door Reversal

Door Reversal continued...

Refit Lower Door

12. Take off the two screw covers from the left hand centre panel and remove

the two screws. Fit these screws and covers over on the right hand side.

13. Fit the centre hinge on the left hand side with the original screws, cover the

screws with the original covers.

14. Using a thin blunt instrument, remove the hinge

bush cap from the top left of the lower door and fit

on the top right.

Note : You may require assistance to do this:

15. Place the lower door onto the lower hinge pin.

16. Offer the door up to the centre hinge.

Put the hinge pin through the centre hinge and

ensure it locates into the door. Check that the hinge

pin is positioned the right way up.

Refit Top Door

17. Using a thin blunt instrument, remove the hinge

bush cap from the top left of the door and refit on

the top right.

18. Replace the spacing washers onto the centre hinge bracket.

Note : You may require assistance to do this:

20. If necessary, slacken off the screws on the centre hinge pin and adjust the

doors so that they line up with the cabinet.

21. Adjust the front feet (see ‘Levelling’ SAFETY & INSTALLATION section).

22. Fit the bottom hinge covers (see ‘Hinge Covers’ in the SAFETY &

INSTALLATION section).

Note : Let the appliance stand upright in it’s final location for at least 15

minutes before plugging in and switching on the electricity supply.

11. Screw the bottom hinge pin complete with spacing washers,

into the left hinge bracket.

19. Place the top door hinge onto the top left of the door, slide the

door onto the centre hinge pin. Support the door while

screwing the top hinge into position.

Ensure that the hinge bracket locates correctly.

CLEANING &

MAINTENANCE

Page is loading ...

Hotpoint Freezer FFS70 User manual

Brand: Hotpoint

Model: Freezer FFS70

Category: Combi-fridges

Type: User manual

This manual is also suitable for

Download PDF

report

Hotpoint Freezer FFS70 User manual

This manual is also suitable for

Hotpoint Freezer FFS70 User manual

Related papers

Other documents