Infinity Kappa Series KAPPA ONE User manual

Kappa Series KAPPA ONE
Infinity
Brand
Infinity
Model
Kappa Series KAPPA ONE
Type
User manual

Infinity Kappa Series KAPPA ONE is a powerful car amplifier designed to deliver exceptional sound quality and flexibility for your car audio system. With its robust construction and advanced features, it offers a range of capabilities that cater to various needs and preferences.

  • High Power Output: Experience exceptional sound clarity and power with 500W RMS x 1 channel at 4 ohms and 800W RMS x 1 channel at 2 ohms.

  • Variable Subsonic High-Pass Filter with Variable Boost (Q): Optimize your subwoofer's performance by adjusting the frequency and boost levels, allowing you to tailor the bass response to your liking.

Infinity Kappa Series KAPPA ONE is a powerful car amplifier designed to deliver exceptional sound quality and flexibility for your car audio system. With its robust construction and advanced features, it offers a range of capabilities that cater to various needs and preferences.

  • High Power Output: Experience exceptional sound clarity and power with 500W RMS x 1 channel at 4 ohms and 800W RMS x 1 channel at 2 ohms.

  • Variable Subsonic High-Pass Filter with Variable Boost (Q): Optimize your subwoofer's performance by adjusting the frequency and boost levels, allowing you to tailor the bass response to your liking.

KAPPA
®
ONE
KAPPA
KAPPA
®
ONE
®
0058CSK - Infinity Kappa One OM Cover HIGH.indd 2 29/09/08 15:49:08
A
ABCD
3x
4x
1x
1x
¡

A
B

3a
ENGLISH
0058CSK - Infinity Kappa One OM Cover HIGH.indd 4 29/09/08 15:49:10
Installation Warnings and Tips
•Disconnect the negative (–) lead from your vehicle’s battery.
•Attheinstallationsites,locateandmakeanoteofallfuel
lines, hydraulic brake lines, vacuum lines and electrical
wiring. Use extreme caution when cutting or drilling in and
around these areas.
•Chooseasafemountinglocationawayfrommoisture.
•Makesurethereissufcientaircirculationatthemount-
ing location for the amplifier to cool itself.
•Mounttheamplier,usingthesuppliedhardware.
Specifications
•500WRMSx1channel@4ohms
<
–
1% THD + N*
•800WRMSx1channel@2ohms
<
–
1% THD + N*
•Total peak power: 1600W
•Frequency response: 20Hz – 320Hz (– 3dB)
•Maximuminputsignal:6V*
•Maximumsensitivity:200mV*
•THD + N: 0.05%
•Signal-to-noise ratio: 85dBA (reference to 1 watt)*
•Signal-to-noise ratio: 109dBA (reference to rated power)
* CEA-2006A-compliant
0
Speaker Output Connectors
•Connectthespeakerstotheseterminals,observing
proper polarity. Gold screws indicate +, and silver
screws indicate – .
•Minimumspeakerimpedanceis2ohms.
1
Fuses
•Replaceonlywiththesametypeandrating.
2
Power Input Connectors
•+12V:Connecttothepositiveterminalofthevehicle’s
battery. Install an appropriate fuse holder and fuse
(120Aminimum)within18”(457mm)ofthebattery.
Makesurethewireisnotdamagedorpinchedduring
installation. Install protective grommets when routing
wires through the firewall or other sheet metal.
•GND:Connecttothevehicle’schassis.Refertothe
illustration below.
•REM:Connecttothe“RemoteOut”leadfromthe
source unit or to a source of switched +12V(ACC).
4 AWG Adapter
•Forpowerwirelongerthan4’(1.2m),4AWGwireis
recommended. Use the adapter to make the connection
according to the illustration below.
3
DBO: Variable Subsonic High-Pass
Filter With Variable Boost (Q)
•Forwoofersintuned(vented)enclosures,setthe
frequency control to a value 10Hz below the enclo-
sure’s resonance (tuned) frequency.
•Forwoofersinsealedboxes,setthecontroltoany
value you prefer between 30Hz and 50Hz.
•SettheBoostcontrolaccordingtoyourpreference,
being careful not to apply enough boost to damage
your woofer(s).
ADBOBoostcontrolprovidesupto12dBofboost,
slightly above the high-pass filter’s frequency.
See above for appropriate settings.
B
DBOHigh-PassFilterFrequencycontrol,variable
between 10Hz and 80Hz. See above for appropri-
ate settings.
4
Crossover-Frequency Control
•12dB/octavecrossover,variablefrom32Hzto320Hz.
See
for the adjustment procedure.
Input Level Control
•Usedtomatchtheinputleveloftheamplierto
the output level of the source unit. See
A
for the
adjustment procedure.
Input Connectors
•Connecttofrontoutputsfromthesourceunitor
signal processor.
Aux Output Connectors
•Nonlteredpass-throughoutput.Connecttothe
input of an additional subwoofer amplifier.
Protect LED
•Illuminatedunderanyofthefollowingfault
conditions: battery over/under voltage; short
circuit in speaker wires; amplifier is too hot;
amplifier’s output circuit has failed (DC voltage
present in the amplifier’s output).
Power On LEDs
•Illuminatedwhentheamplierison.
A
Setting Input Level
ATurnInputLevelcontrolcounterclockwiseto6V.
B With a dynamic music track playing, turn the head
unit’svolumecontroltothe3/4position.
C Turn Input Level control clockwise until the bass
output is proportionate to the output of the high-
frequency speakers, according to your preference.
D Input level is now adjusted correctly.
Setting the Crossover
A Crossover setting for subwoofers.
Note: Acceptable frequency ranges indicated in gray.
Factory Bolt Ring Connector
Ground Wire
Note: Remove any paint
below ring connector.
Star Washer
This product is designed for mobile applications and is not intended
for connection to the mains.
A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change
without notice.
3a
ENGLISH
0058CSK - Infinity Kappa One OM Cover HIGH.indd 5 29/09/08 15:49:10
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA
Infinity and Kappa are trademarks of Harman International Industries, Incorporated,
registered in the United States and/or other countries.
www.infinitysystems.com
©2008HarmanInternationalIndustries,Incorporated.Allrightsreserved.•PartNo.KAPPA10M9/08
Declaration of Conformity
We, Harman Consumer Group, Inc.
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the product described
in this owner’s manual is in compliance with technical
standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
Klaus Lebherz
Harman Consumer Group, Inc.
Château du Loir, France 9/08
KAPPA
®
ONE
0058CSK - Infinity Kappa One OM Cover HIGH.indd 3 29/09/08 15:49:08
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Infinity Kappa Series KAPPA ONE User manual

Kappa Series KAPPA ONE
Infinity
Brand
Infinity
Model
Kappa Series KAPPA ONE
Type
User manual

Infinity Kappa Series KAPPA ONE is a powerful car amplifier designed to deliver exceptional sound quality and flexibility for your car audio system. With its robust construction and advanced features, it offers a range of capabilities that cater to various needs and preferences.

  • High Power Output: Experience exceptional sound clarity and power with 500W RMS x 1 channel at 4 ohms and 800W RMS x 1 channel at 2 ohms.

  • Variable Subsonic High-Pass Filter with Variable Boost (Q): Optimize your subwoofer's performance by adjusting the frequency and boost levels, allowing you to tailor the bass response to your liking.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents