AMX CB-MXP-43-F Quick start guide

Type
Quick start guide

AMX CB-MXP-43-F is an optional accessory for the Modero X Series 4.3” Wall Mount Touch Panel. It is designed to be flush mounted in new construction applications with drywall. The Flush Mount Rough-In Box kit includes a wall box, cover, and mounting screws. The back of the Modero X Series 4.3” Flush Wall Mount Touch Panel is contained within a plastic outer housing or back box, and the back box attaches to the Rough-In Box. The Rough-In Box With Cover dimensions are 7.96" x 5.08" x 3.47", and it weighs 1.80 lbs without the cover. The Rough-In Box has two knockouts for wiring, and it is UL Listed. The included Cover Plate covers the Rough-In Box.

AMX CB-MXP-43-F is an optional accessory for the Modero X Series 4.3” Wall Mount Touch Panel. It is designed to be flush mounted in new construction applications with drywall. The Flush Mount Rough-In Box kit includes a wall box, cover, and mounting screws. The back of the Modero X Series 4.3” Flush Wall Mount Touch Panel is contained within a plastic outer housing or back box, and the back box attaches to the Rough-In Box. The Rough-In Box With Cover dimensions are 7.96" x 5.08" x 3.47", and it weighs 1.80 lbs without the cover. The Rough-In Box has two knockouts for wiring, and it is UL Listed. The included Cover Plate covers the Rough-In Box.

Quick Start Guide
CB-MXP-43-F
Flush Mount Rough-In Box for Modero X 4.3” Panel
Overview
The Flush Mount Rough-In Box (FG5968-82) is an optional accessory for
the Modero X Series 4.3” Wall Mount Touch Panel. It is designed to be flush
mounted in new construction applications with drywall.
The back of the Modero X Series 4.3” Flush Wall Mount Touch Panel is
contained within a plastic outer housing or back box, and the back box
attaches to the Rough-In Box. The Rough-In Box kit includes a wall box,
cover, and mounting screws.
Specifications
Drywall and Stud Mounting
1. Remove the cover in FIG. A from the rough-in box before installation.
2. Break the four bent tabs around the front of the box off (Fig B).
3. Mount the metal box with its leading edge flush with the stud using
wood screws (not included) through the box flanges and interior as
shown below.
4. Remove the appropriate wiring knockouts from the rough-in box to
accommodate the cables being threaded through to the wall mount
touch panel.
5. Thread the incoming cable through one of the two knockouts (top or
bottom). Leave enough slack in the wiring to accommodate installation
of the flush mount kit.
6. After drywall is installed (with cover removed), use a rotary cutting tool
or drywall saw to cut to the inside dimensions of the rough-in box. If
using the included front cover, small notches may be needed to clear
the four raised tabs on the cover. Do not shave off more drywall than
necessary for clearance to insure that the flush mount kit will cover the
entire opening after installation.
Note: The front cover shown in FIG. A should be installed after the
appropriate wiring is pulled to the Rough-In Box. The cover should then be
removed prior to the installation of the touch panel back box and discarded.
FIG. 1 93-5968-82 Rough-In Box
7.96”
(20.22 cm)
4.14” (10.52 cm)
5.08”
Rough-In Box With Cover
Cover
(12.90 cm)
A
(93-5968-82) Specifications
Dimensions (HWD) Rough-In Box: 7.96" x 5.08" x 3.47"
(20.22 cm x 12.9 cm x 8.8 cm)
Weight Without cover: 1.80 lbs (0.82 kg)
Certifications UL Listed
Included
Accessories:
Cover Plate to cover Rough-In Box (62-5968-94)
Rough-In Box Cover Mounting Screws (2) (80-5967-05)
NEW CONSTRUCTION
(Pre-1/2” Wallboard)
Install Flush With
Front Of Stud
Remove Four
Front Tabs
Screws In Stud
(Not Included)
B
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
10/14
©2014 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-5968-82 REV: B
FG5968-82
Rough-In Box
With Cover
Side knock-out
Front
(oblique angle)
Cover screws
3.47”
(8.8 cm)
4.14”
(10.52 cm)
3.47”
(8.8 cm)
4.14”
(10.52 cm)
3.47”
(8.8cm)
4.14”
(10.52 cm)
Front
7.96”
(20.22cm)
Bottom View
Side View
Top View
Flush Mount
Side knock-out
  • Page 1 1
  • Page 2 2

AMX CB-MXP-43-F Quick start guide

Type
Quick start guide

AMX CB-MXP-43-F is an optional accessory for the Modero X Series 4.3” Wall Mount Touch Panel. It is designed to be flush mounted in new construction applications with drywall. The Flush Mount Rough-In Box kit includes a wall box, cover, and mounting screws. The back of the Modero X Series 4.3” Flush Wall Mount Touch Panel is contained within a plastic outer housing or back box, and the back box attaches to the Rough-In Box. The Rough-In Box With Cover dimensions are 7.96" x 5.08" x 3.47", and it weighs 1.80 lbs without the cover. The Rough-In Box has two knockouts for wiring, and it is UL Listed. The included Cover Plate covers the Rough-In Box.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI