dbx 442 Owner's manual

Brand: dbx

Model: 442

Category: Audio equalizers

Type: Owner's manual

This manual is also suitable for

User Manual

Complete Equalization & Loudspeaker Management System

442

480

481

482

480R

WARNING FOR YOUR PROTECTION

PLEASE READ THE FOLLOWING:

KEEP THESE INSTRUCTIONS

HEED ALL WARNINGS

FOLLOW ALL INSTRUCTIONS

CLEAN ONLY WITH A DRY CLOTH.

DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE

MANUFACTURER’S INSTRUCTIONS.

DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES,

OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.

ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.

UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERI-

ODS OF TIME.

GROUNDING PRONG: The wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for replacement of the

obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, conve-

nience receptacles, and the point where they exit from the apparatus.

Use only with the cart stand, tripod bracket, or table specified by the manufacture, or sold

with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

Refer all servicing to to qualified service personnel. Servicing is required when the appa-

ratus has been damaged in any way, such as power-supply cord or plug is damaged, liq-

uid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

POWER ON/OFF SWITCH: The Power switch used in this piece of equipment DOES NOT break

the connection from the mains.

ALL-POLE MAINS SWITCH: An all-pole mains switch with a contact separation of at least

3mm in each pole shall be incorporated in the electrical installation of the rack or build-

ing.

FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE: Replace fuse with

same type and rating only.

MULTIPLE-INPUT VOLTAGE: This equipment may require the use of a different line cord,

attachment plug, or both, depending on the available power source at installation. Connect

this equipment only to the power source indicated on the equipment rear panel. To reduce

the risk of fire or electric shock, refer servicing to qualified service personnel or

SAFETY INSTRUCTIONS

NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A POWER

CORD.

WARNING: THIS APPLIANCE MUST BE EARTHED.

CAUTION: EQUIPMENT IS NOT DISCONNECTED FROM MAINS WHEN

SWITCH IS IN THE OFF POSITION

The cores in the mains lead are coloured in accordance with the following

code:

GREEN and YELLOW - Earth BLUE - Neutral BROWN - Live

As colours of the cores in the mains lead of this appliance may not corre-

spond with the coloured markings identifying the terminals in your plug, pro-

ceed as follows:

• The core which is coloured green and yellow must be connected to the

terminal in the plug marked with the letter E, or with the earth symbol,

or coloured green, or green and yellow.

• The core which is coloured blue must be connected to the terminal

marked N or coloured black.

• The core which is coloured brown must be connected to the terminal

marked L or coloured red.

This equipment may require the use of a different line cord, attachment plug,

or both, depending on the available power source at installation. If the attach-

ment plug needs to be changed, refer servicing to qualified service personnel

who should refer to the table below. The green/yellow wire shall be connect-

ed directly to the units chassis.

WARNING: If the ground is defeated, certain fault conditions in the unit or in

the system to which it is connected can result in full line voltage between

chassis and earth ground. Severe injury or death can then result if the chas-

sis and earth ground are touched simultaneously.

LIVE

ENEUTRAL

EARTH GND

CONDUCTOR

NBROWN

BLUE

GREEN/YEL

BLACK

Normal Alt

WIRE COLOR

WHITE

GREEN

The symbols shown above are internationally accepted symbols that

warn of potential hazards with electrical products. The lightning flash

with arrowpoint in an equilateral triangle means that there are dangerous

voltages present within the unit. The exclamation point in an equilateral

triangle indicates that it is necessary for the user to refer to the owner’s

manual.

These symbols warn that there are no user serviceable parts inside the

unit. Do not open the unit. Do not attempt to service the unit yourself.

Refer all servicing to qualified personnel. Opening the chassis for any

reason will void the manufacturer’s warranty. Do not get the unit wet. If

liquid is spilled on the unit, shut it off immediately and take it to a deal-

er for service. Disconnect the unit during storms to prevent damage.

CAUTION

ATTENTION: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT SAFETY INSTRUCTIONS

U.K. MAINS PLUG WARNING

Amolded mains plug that has been cut off from the cord is

unsafe. Discard the mains plug at a suitable disposal facility.

NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A

DAMAGED OR CUT MAINS PLUG INTO A 13 AMP POWER SOCK-

ET. Do not use the mains plug without the fuse cover in place.

Replacement fuse covers can be obtained from your local retail-

er. Replacement fuses are 13 amps and MUST be ASTA approved

to BS1362.

LITHIUM BATTERY

WARNING

CAUTION!

This product may contain a lithium battery.There is danger of

explosion if the battery is incorrectly replaced. Replace only

with an Eveready CR 2032 or equivalent. Make sure the bat-

tery is installed with the correct polarity. Discard used batter-

ies according to manufacturer’s instructions.

ADVARSEL!

Lithiumbatteri - Eksplosjonsfare.Ved utskifting benyttes kun

batteri som anbefalt av apparatfabrikanten. Brukt batteri

returneres apparatleverandøren.

ADVARSEL!

Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri av samme fabrikat og

type. Levér det brugte batteri tilbage til leverandøren.

VAROITUS!

Paristo voi räjähtää, jos se on virheellisesti asennettu.Vaihda

paristo ainoastaan laitevalmistajan suosittelemaan tyyppin.

Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

VARNING!

Explosionsfara vid felaktigt batteribyte.Använd samma batteri-

typ eller en ekvivalent typ som rekommenderas av apparattil-

lverkaren. Kassera använt batteri enligt fabrikantens instruk-

tion.

IMPORTANT SAFETY INSTRUCTIONS

ELECTROMAGNETIC

COMPATIBILITY

This unit conforms to the Product

Specifications noted on the Declaration of

Conformity. Operation is subject to the fol-

lowing two conditions:

• this device may not cause harmful inter-

ference, and

• this device must accept any interference

received, including interference that may

cause undesired operation.

Operation of this unit within significant electro-

magnetic fields should be avoided.

• use only shielded interconnecting cables.

DECLARATION OF

CONFORMITY

Manufacturer’s Name: dbx Professional Products

Manufacturer’s Address: 8760 S. Sandy Parkway

Sandy, Utah 84070, USA

declares that the product:

Product name: dbx Drive Rack 442,480,481,482

Note: Product name may be suffixed by the r, s, t, p and EU

Product option: None

conforms to the following Product Specifications:

Safety: IEC60065 (1998)

EN 60065 (1993)

CAN/CSA E60065-99

EMC: EN 55013 (1990)

EN 55020 (1991)

Supplementary Information:

The product herewith complies with the requirements of the Low Voltage

Directive 72/23/EEC and the EMC Directive 89/336/EEC as amended by

Directive 93/68/EEC.

dbx Professional Products

8760 S. Sandy Parkway

Sandy, Utah 84070, USA

March 15,2000

Revised: August 15,2001

European Contact: Your local dbx Sales and Service Office or

Harman Music Group

8760 South Sandy Parkway

Sandy, Utah

84070 USA

Ph: (801) 566-8800

Fax: (801) 568-7573

Ta b le of Contents

DriveRack™

Introduction

1.1 Defining the DriveRack™ System ...................ii

1.2 Service Contact Info........................................iv

1.3 Warranty...........................................................iv

Section 1 - Getting Started

1.1 Rear Panel Connections (480) .........................2

1.2 Front Panel (480) ............................................3

1.3 Rear Panel Connections (481) .........................4

1.4 Front Panel (481) ............................................5

1.5 Rear Panel Connections (482) .........................6

1.6 Front Panel (482) ............................................7

1.7 Rear Panel Connections (442) .........................9

1.8 Front Panel (442) ..........................................10

Section 2 - Editing Functions

2.1 Basic Navigation Modes.................................14

2.2 Button Array Overview..................................15

2.3 Parameter Knob Encoders Coarse/Fine ........16

2.4 (Horizontal-Vertical nav)................................16

2.5 Cut and Paste..................................................16

2.6 Navigating the EQ Sections ...........................17

2.7 Navigating the Crossover Section..................18

2.8 Navigating the RTA Section ...........................19

2.9 Navigating the Delay Section ........................20

2.10 Navigating the Dynamics Section................21

2.11 Navigating the Other Section.......................22

2.12 Navigating the Utility Section ......................23

Section 3 - Configuring the

DriveRack

3.1 Program Definition.........................................26

3.2 Navigating Factory Programs.........................26

3.3 Editing Factory Programs...............................28

3.4 Saving Factory Program Changes..................28

3.5 Creating a User Configuration.......................30

3.6 Linking Modules .............................................32

3.7 Selecting and Moving Crossovers..................33

3.8 Saving Configuration Changes.......................34

Section 4 - Detailed Parameters

4.1 Input Routing..................................................36

4.2.1 Pre-Crossover EQ (31 Band Graphic)........36

4.2.2 Pre-Crossover EQ (31 Band Graphic)

Show and House ..................................................37

4.2.3 Pre-Crossover EQ (9-Band Parametric)......37

4.2.4 RTA...............................................................38

4.3 Notch Filter .....................................................39

4.4 Delay (Pre-Crossover) ....................................39

4.5 Crossovers.......................................................39

4.6 Post-Crossover Parametric EQ.......................39

4.7 Compressor/Limiter (Dynamics)....................44

4.8 Speaker Alignment Delay ..............................45

4.9 Output Routing...............................................46

Section 5 - Storing Changes

5.1 Saving Factory Program Changes..................48

5.2 Saving Configuration Changes.......................50

Section 6 - Utilities

6.1 Network ID.....................................................52

6.2 Security Levels ................................................52

6.3 Security Passwords .........................................53

6.4 Entering Security Password ...........................54

6.5 Program List....................................................55

6.6 Program Change Mode ..................................54

6.7 Contrast Adjustment .......................................57

6.8 PC COMM Mode ............................................57

6.9 Power-up (Mutes/Saved) ...............................58

6.10 MIDI Channels..............................................58

6.11 MIDI Program Dumps..................................58

6.12 SYSEX Dump ................................................59

6.13 Setup SYSEX ID............................................59

6.14 Mic Pre Set up ..............................................59

6.15 Redundancy Enable......................................60

Section 7 - Network Functions

7.1 Network Connections (Specs) .......................63

7.2 Network Connections (Applications)............64

7.3 Host/Sync Assignments.................................. 68

7.4 Redundancy ....................................................71

7.5 Network Trouble Shooting ............................72

7.6 PC GUI Install and basic operation ..............73

7.7 System Control................................................79

DriveRack™ User Manual

Table of Contents

Ta b le of Contents

DriveRack™

Section 8 - 480 Remote Controller

8.1 Rear Panel Connections .................................86

8.2 Front Panel Connections................................87

8.3 Rear Panel Connections (480P).....................88

8.4 Front Panel (480P) .........................................89

8.5 Using the RTA.................................................90

8.6 Hot Key Assignments.....................................91

8.7 Controlling Synchronized devices..................91

8.8 480R Utility Menu...........................................92

8.9 480R System Control ......................................96

Section 9 - Application Guide

9.1 Four Way FOH .............................................100

9.2 Front of House w/Delay 3-Way Towers .....101

9.3 L-C-R + Sub + Rear.......................................102

9.4 Bi-Amp & In-Ear...........................................103

9.5 Dedicated FOH Crossover ...........................104

9.6 Stand-Alone Monitor EQ..............................105

Section 10 - Appendix

A.1 MIDI SYSEX..................................................108

A.2 Factory Reset ................................................111

A.3 Power up Quick Key Options ....................111

A.4 Flash Downloads .........................................112

A.5 Program List .................................................112

A.6 Specifications................................................113

A.7 Crossover Diagrams .....................................118

A.8 Gain Jumper Warning..................................123

A.9 Input and Output Section Diagrams...........124

A.10 “Pinking” a Room ......................................125

A.11 Wire Diagrams............................................126

DriveRack™ User Manual Table of Contents

INTRO

CUSTOMER SERVICE INFO

Defining the

DriveRack

WARRANTY INFO

®

INTRODUCTION

DriveRack™

Introduction

DriveRack™ User Manual

DriveRack™

Congratulations on your purchase of the dbx DriveRack™ Complete Equalization and

Loudspeaker Management System! For over 30 years, dbx has been the industry leader in

dynamics processing. With the introduction of the DriveRack™ , dbx Professional Products has

redefined the standard by which all other loud speaker management systems will be based

This manual will be your guide to understanding the full functionality of the powerful 480, 481,

482, 442 and 480R DriveRack™ units. By combining the different components, the configura-

tion possibilities are limitless. After you have become familiar with the unit, we encourage you

to experiment and find the most effective and efficient way to run your system by utilizing the

powerful processing of the DriveRack™.

The dbx DriveRack™ is the most effective way to manage all aspects of post mix processing

and signal routing. The following are just some of the features of the 480, 481, 482 and 480R.

480 DriveRack™ features:

•4 Input and 8 Outputs with routing

•31 band graphic or 9 band parametric equalizer on every input (pre-crossover)

• Dual Real Time Audio Analyzers

•Butterworth, Bessel or Linkwitz-Riley crossover filters

•27 Different Crossover Configurations

•Time Alignment and Transducer Alignment Delays

•Compressor/Limiter on every output

•Speaker Compensation EQ (post crossover)

•Multi-level Security System

•Separate House and Show EQ with individual lockouts

•Triple redundant back up of all parameters when running network, 480R and PC GUI

•TYPE IV™ Conversion System

•Electronically balanced/RF filtered XLR Inputs and Outputs

•Proprietary RS-485 Control Network

•RS-232 PC Interface for computer display and configuration

481 DriveRack™ features:

•4 Input and 8 Outputs with routing

•31 band graphic or 9 band parametric equalizer on every input (pre-crossover)

• Dual Real Time Audio Analyzers

•Butterworth, Bessel or Linkwitz-Riley crossover filters

•27 Different Crossover Configurations

1.1 Defining the DriveRack™ System

INTRODUCTION

Introduction

DriveRack™

DriveRack™ User Manual

•Time Alignment and Transducer Alignment Delays

•Compressor/Limiter on every output

•Speaker Compensation EQ (post crossover)

•Multi-level Security System

•Separate House and Show EQ with individual lockouts

•Triple redundant backup of all parameters when running network, 480R and PC GUI

•TYPE IV™ Conversion System

•Electronically balanced/RF filtered Euroblock Inputs and Outputs

•Proprietary RS-485 Control Network

•RS-232 PC Interface for computer display and configuration

482 DriveRack™ features:

•4 Input and 8 Outputs with routing

•31 band graphic or 9 band parametric equalizer on every input (pre-crossover)

• Dual Real Time Audio Analyzers

•Butterworth, Bessel or Linkwitz-Riley crossover filters

•27 Different Crossover Configurations

•Time Alignment and Transducer Alignment Delays

•Compressor/Limiter on every output

•Speaker Compensation EQ (post crossover)

•Multi-level Security System

•Separate House and Show EQ with individual lockouts

•Triple redundant back up of all parameters when running network, 480R and GUI

•TYPE IV™ Conversion System

•Electronically balanced/RF filtered XLR Inputs and Outputs

•Proprietary RS-485 Control Network

•RS-232 PC Interface for computer display and configuration

442 DriveRack™ features:

•4 Input and 4 Outputs

•31 band graphic or 9 band parametric equalizer on every input

•Time Alignment Delays

•Compressor/Limiter on every output

•Multi-level Security System

•Separate House and Show EQ with individual lockouts

•Triple redundant back up of all parameters when running network, 480R and GUI

•TYPE IV™ Conversion System

•Electronically balanced/RF filtered XLR Inputs and Outputs

•Proprietary RS-485 Control Network

•RS-232 PC Interface for computer display and configuration

iii

Introduction

DriveRack™ User Manual

DriveRack™

480R DriveRack™ features:

•Dedicated remote interface to control all 480, 481, 482 and 442 DriveRack™ units

•31 Motorized faders for equalization control

•32 assignable hot-keys with up to 64 different assignment capabilities

•Built-in Real Time Audio Analyzer (with rear-panel XLR connector)

•System Mute button

•Proprietary RS-485 Control Network

•RS-232 PC Interface for computer display and configuration

•480P Power Supply Included

•Responds to MIDI commands from mixing consoles including: Soundcraft™ SM20

and Series 5 and the Allen & Heath™ ML 4000 and ML5000

By including every form of processing necessary to drive the signal from the mixer to the power

amp, the DriveRack™ allows you to eliminate all other processing devices that are normally

found in large and cumbersome traditional DriveRack systems of the past.

The 480 DriveRack™ Loud Speaker Management System includes four balanced XLR inputs, as

well as eight balanced XLR outputs, which can be routed for any configuration. The 481 and

482 DriveRack™ feature the identical processing power of the 480 DriveRack, but utilize stream-

line front panel interfaces. In addition, the 481 utilizes euroblock connectors as opposed to the

XLR connectors found in the 480 and 482 DriveRack.

The 480, 481 and 482 DriveRacks™ include features such as: pre-crossover EQ, dual RTAs, notch

filters, speaker delays, multiple crossovers and compression/limiting, as well as numerous other

features. Dual RTA analyzers can be run simultaneously with RTA source inputs capable of

being remotely switched on the fly. The 480 DriveRack™ is fully programmable from the front

panel, and can control other devices in a network including the 481 and 482 synchronized

units. In addition, the entire system can be controlled via the 480R DriveRack™ remote

controller or through the included GUI interface.

The 442 DriveRack Equalization Management system is the perfect tool for monitor mixing

applications. The 442 offers four balanced XLR inputs and four XLR outputs, with four inde-

pendent channels of effect processing. Each channel offers a 31-band graphic or parametric

equalizers, as well as digital delay and industry-standard, dbx dynamics processing.

If you require technical support, contact dbx Customer Service. Be prepared to accurately

describe the problem. Know the serial number of your unit - this is printed on a sticker attached

to the rear panel. If you have not already taken the time to fill out your warranty registration

card and send it in, please do so now.

1.2 Service Contact Info

Before you return a product to the factory for service, we recommend you refer to the manual.

Make sure you have correctly followed installation steps and operation procedures. If you are still

unable to solve a problem, contact our Customer Service Department at (801) 568-7660 for con-

sultation. If you need to return a product to the factory for service, you MUST contact Customer

Service to obtain a Return Authorization Number.

No returned products will be accepted at the factory without a Return Authorization Number.

Please refer to the Warranty below, which extends to the first end-user. After expiration of the war-

ranty, a reasonable charge will be made for parts, labor, and packing if you choose to use the fac-

tory service facility. In all cases, you are responsible for transportation charges to the factory. dbx

will pay return shipping if the unit is still under warranty.

Use the original packing material if it is available. Mark the package with the name of the shipper

and with these words in red: DELICATE INSTRUMENT, FRAGILE! Insure the package properly.

Ship prepaid, not collect. Do not ship parcel post.

This warranty is valid only for the original purchaser and only in the United States.

1. The warranty registration card that accompanies this product must be mailed within 30 days

after purchase date to validate this warranty. Proof-of-purchase is considered to be the burden

of the consumer.

2. dbx warrants this product, when bought and used solely within the U.S., to be free from defects

in materials and workmanship under normal use and service.

3. dbx liability under this warranty is limited to repairing or, at our discretion, replacing defective

materials that show evidence of defect, provided the product is returned to dbx WITH RETURN

AUTHORIZATION from the factory, where all parts and labor will be covered up to a period of

two years. A Return Authorization number must be obtained from dbx by telephone. The com-

pany shall not be liable for any consequential damage as a result of the product's use in any

circuit or assembly.

4. dbx reserves the right to make changes in design or make additions to or improvements upon

this product without incurring any obligation to install the same additions or improvements on

products previously manufactured.

5. The foregoing is in lieu of all other warranties, expressed or implied, and dbx neither assumes

nor authorizes any person to assume on its behalf any obligation or liability in connection with

the sale of this product. In no event shall dbx or its dealers be liable for special or consequen-

tial damages or from any delay in the performance of this warranty due to causes beyond their

control.

1.3 Warranty

Introduction Section i

DriveRack™

DriveRack™ User Manual v

Introduction

DriveRack™ User Manual

Section i DriveRack™

®

Getting Started

Section 1

DriveRack™

Getting Started

DriveRack™ User Manual

Section 1 DriveRack

™

IEC Power Cord Receptacle

The 480 comes with an International power supply that will accept voltages ranging from 100V-

240V at frequencies from 50Hz-60Hz. An IEC cord is included.

MIDI In, Out and Thru Connectors

These connectors provide MIDI functionality to the 480 DriveRack™. The In, Out and Thru jacks

allow you to use the 480 DriveRack™ at any point in the MIDI chain.

RS485 Control Bus Input (DB-9 connector type)

This input network connection is used to receive information being sent from other units in the

DriveRack™ network link.

RS485 Control Thru Bus (DB-9 connector type)

This Thru network connection is used to pass information to other units in the DriveRack™ net-

work link.

RS485 Control Bus Input (RJ-45 connector type)

This input network connection is used to receive information being sent from other units in the

DriveRack™ network link.

RS485 Control Thru Bus (RJ-45 connector type)

This Thru network connection is used to pass information to other units in the DriveRack™ net-

work link.

Termination LEDs

These LEDS indicate when network is properly terminated. The Green LED indicates that the

network has been correctly terminated.

Remote Controller In Connection

This DB-9 type input connection is used to send and receive information from the 480R Remote

Control unit.

PC Connection

This DB-9 type connection is used to send and receive information to and from the GUI inter-

face.

Outputs 1-8

The output section of the 480 DriveRack™ offers eight electronically balanced XLR connectors.

35 WATTS

1.1 Rear Panel Connections (480)

Inputs 1-4

The input section of the 480 DriveRack™ offers four electronically balanced XLR connectors.

Inputs 3 and 4 offer Line/RTA switches that allow you to run a real time audio analyzer micro-

phone directly into the input of the 480 DriveRack™. The four XLR inputs of the 480

DriveRack™ also offer Pin 1 lift switches which lift the ground of the selected XLR input pair

when pressed.

WARNING - For proper operation of the RTA microphone, the RTA button must be depressed

and the ground /lift switch must be in the grounded position. When the RTA button on the back

panel is depressed, 48V phantom power is applied to pins 2 and 3 of the XLR connector. To

maintain a proper ground return for the phantom power, the ground/lift switch must be in the

grounded position. This will prevent the possibility of electrical shock.

LCD Display

The large LCD display of the 480 DriveRack™ provides the user with all of the vital processing

information of the DriveRack™ including: signal routing, configuration modes, effect block edit-

ing and RTA displays. The top left corner of the display indicates network device ID numbers.

The reverse background number indicates the number of the synchronized unit being

controlled, while Mst indicates that the unit is set to act as the host.

Function Buttons

The function buttons of the 480 DriveRack™ allow access to all editing and navigating functions

of the 480 DriveRack™.

Parameter Knobs

The parameter knobs of the 480 DriveRack™ allow the user to edit parameters of selected

effects of the 480 DriveRack™. The parameter knobs of the 480 and 480R DriveRack™ units

also incorporate light display Logicators™ which surround the knob itself and indicate levels of

parameter and effect activity. The parameter knobs of the 480 DriveRack™ also provide the

25 40 63 100 160 250 400 630 1.0k 1.5k 2.5k 4.0k 6.3k 10k 16k

20 31 50 80 125 200 315 500 800 1.3k 2.0k 3.2k 5.0k 8.0k 13k 20k

+24 +6

+18 +4

+12 +2

+8 0

0 -2

-8 -4

-12 -8

-18 -9

-24 -12

-60 -30

-30 -15

-40 -20

-50 -25

-70 -35

-80 -40

-90 -50

+14

+12

+10

-2

-10

-4

-6

-8

-12

-14

Parameter 1

Parameter 2

Parameter 3



Single RTA

Channel 1

F7 4-Way FOH w/RTA

1.2 Front Panel (480)

Getting Started Section 1

DriveRack

™

DriveRack™ User Manual 3

Getting Started

DriveRack™ User Manual

Section 1 DriveRack

™

user with different modes of functionality including: coarse/fine encoding (successive presses

will toggle the knob between a fast and slow mode of operation) and horizontal-vertical navi-

gators, which allow the parameter buttons (when used in program and configuration mode) to

navigate the program screen horizontally and vertically.

Input Meters

The 480 DriveRack™ provides the user with four independent 12 seg-

ment Lightpipe™ input meters that range from -30 to +22 dBu. Note:

These meters are calibrated for the +22dBu setting of the gain jumpers.

Threshold Meters

The threshold meters indicate that the threshold level has been

exceeded within the dynamics section (compressor/limiter), and gain

reduction is taking place within the specific output channel.

Output Meters

The 480 DriveRack™ provides the user with eight independent 12-seg-

ment Lightpipe™ output meters that range from -30 to +22 dBu. Note:

These meters are calibrated for the +22dBu setting of the gain jumpers.

Output Mutes

The eight output mute buttons are used for independently muting each

output on all eight outputs of the 480 DriveRack™.

Power Switch

Turns the 480 DriveRack™ on and off. Note: dbx Professional

Products recommends that power amps connected to the DriveRack™,

should be powered down prior to cycling the DriveRack™.

IEC Power Cord Receptacle

The 481 comes with an International power supply that will accept voltages ranging from 100V-

240V at frequencies from 50Hz-60Hz. An IEC cord is included.

RS485 Control Bus Input (DB-9 connector type)

This input network connection is used to receive information being sent from other units in the

DriveRack™ network link.

RS485 Control Thru Bus (DB-9 connector type)

This Thru network connection is used to pass information to other units in the DriveRack™ net-

work link.

RS485 Control Bus Input (RJ-45 connector type)

1.3 Rear Panel Connections (481)

Getting Started Section 1

DriveRack

™

This input network connection is used to receive information being sent from other units in the

DriveRack™ network link.

RS485 Control Thru Bus (RJ-45 connector type)

This Thru network connection is used to pass information to other units in the DriveRack™ net-

work link.

Termination LEDs

These LEDS indicate when network is properly terminated. The Green LED indicates that the

network has been correctly terminated.

Remote Controller In Connection

This DB-9 type input connection is used to send and receive information from the 480 Remote

DriveRack™ Unit.

Outputs 1-8 (Euroblock Connectors)

The output section of the 481 DriveRack™ offers eight electronically balanced Euroblock con-

nectors.

Inputs 1-4

The input section of the 481 DriveRack™ offers four electronically balanced Euroblock con-

nectors.

Ground Lift Switch

This switch (when pressed in), is used to lift the Pin one ground on either inputs 1 and 2 or 3

and 4.

PC Connection

This DB-9 type connection is used to send and receive information to and from the GUI inter-

face.

Program Up and Down

These program up and down buttons are used to scroll through the program menu of the 481.

Program Display

This program display is used to indicate the currently selected program of the 481.

ID Display

This ID display is used to indicate the current assigned identification of the 481. This identifi-

cation is essential for unit recognition when the 481 is used in a network system.

Control Bus LED

1.4 Front Panel (481)

DriveRack™ User Manual

Getting Started

Section 1 DriveRack

™

This LED (when lit), indicates that the 481 is connected to the control bus.

When it is flashing, the 481 is sending/receiving network information.

Remote LED

This LED (when lit), indicates that the 481 is connected to the 480R. When

it is flashing, the 481 is sending/receiving information from the 480R.

PC LED

This LED (when lit), indicates that the 481 is connected to the PC. When

it is flashing, the 481 is sending/receiving information from the PC.

Input Meters

The 481 DriveRack™ provides the user with four independent 6-segment

lightpipe™ input meters that range from -30 to +22 dBu. Note: These

meters are calibrated for the +22dBu setting of the gain jumpers.

Output Meters

The 481 DriveRack™ provides the user with eight independent 6-segment

lightpipe™ output meters that range from -30 to +22 dBu. Note: These

meters are calibrated for the +22dBu setting of the gain jumpers.

Power Switch

Turns the 481 DriveRack™ on and off. Note: dbx Professional Products rec-

ommends that power amps connected to the DriveRack™ should be pow-

ered down prior to cycling the DriveRack™.

IEC Power Cord Receptacle

The 482 comes with an International power supply that will accept voltages ranging from 100V-240V

at frequencies from 50Hz-60Hz. An IEC cord is included.

MIDI In, Out and Thru Connectors

These connectors provide MIDI functionality to the 482 DriveRack™. The In, Out and Thru jacks

allow you to use the 482 DriveRack™ at any point in the MIDI chain.

RS485 Control Bus Input (DB-9 connector type)

This input network connection is used to receive information being sent from other units in the

DriveRack™ network link.

1.5 Rear Panel Connections (482)

RS485 Control Thru Bus (DB-9 connector type)

This Thru network connection is used to pass information to other units in the DriveRack™ net-

work link.

RS485 Control Bus Input (RJ-45 connector type)

This input network connection is used to receive information being sent from other units in the

DriveRack™ network link.

RS485 Control Thru Bus (RJ-45 connector type)

This Thru network connection is used to pass information to other units in the DriveRack™ net-

work link.

Termination LEDs

These LEDS indicate when network is properly terminated. The Green LED indicates that the net-

work has been correctly terminated.

Remote Controller In Connection

This DB-9 type input connection is used to send and receive information from the 480 Remote

DriveRack™ Unit.

PC Connection

This DB-9 type connection is used to send and receive information to and from the GUI interface.

Outputs 1-8

The output section of the 482 DriveRack™ offers eight electronically balanced XLR connectors.

Inputs 1-4

The input section of the 482 DriveRack™ offers four electronically balanced XLR connectors.

Inputs 3 and 4 offer Line/RTA switches that allow you to run a real time audio analyzer micro-

phone directly into the input of the 482 DriveRack™. The four XLR inputs of the 482 DriveRack™

also offer Pin 1 lift switches which lift the ground of the selected XLR input pair when pressed.

Warning - For proper operation of the RTA microphone, the RTA button must be depressed and

the ground /lift switch must be in the grounded position. When the RTA button on the back panel

is depressed, 48V phantom power is applied to pins 2 and 3 of the XLR connector. To maintain

a proper ground return for the phantom power, the ground/lift switch must be in the grounded

position. This will prevent the possibility of electrical shock.

1.6 Front Panel (482)

Getting Started Section 1

DriveRack

™

Getting Started

DriveRack™ User Manual

Section 1 DriveRack

™

PC Connection

This DB-9 type connection is used to send and receive information to and from the GUI interface.

Program Up and Down

These program up and down buttons are used to scroll through the pro-

gram menu of the 482.

Program Display

This program display is used to indicate the currently selected program of the 482.

ID Display

This ID display is used to indicate the current assigned identification of the 482. This identifica-

tion is essential for unit recognition when the 482 is used in a network system.

Control Bus LED

This LED (when lit), indicates that the 482 is connected to the control bus.

When it is flashing, the 482 is sending/receiving network information.

Remote LED

This LED (when lit), indicates that the 482 is connected to the 480R.

When it is flashing, the 482 is sending/receiving information from the

480R.

PC LED

This LED (when lit), indicates that the 482 is connected to the PC. When

it is flashing, the 482 is sending/receiving information from the PC.

Input Meters

The 482 provides the user with four independent 12 segment lightpipe™

input meters that range from -30 to +22 dBu. Note: These meters are

calibrated for the +22dBu setting of the gain jumpers.

Threshold Meters

The threshold meters indicate that the threshold level has been exceeded within the dynamics sec-

tion (compressor/limiter), and gain reduction is taking place within the specific output channel.

Output Meters

The 482 DriveRack™ provides the user with eight independent 12-seg-

ment lightpipe™ output meters that range from -30 to +22 dBu. Note:

These meters are calibrated for the +22dBu setting of the gain jumpers.

Output Mutes

The eight output mute buttons are used for independently muting each

output of the 482 DriveRack™.

Power Switch

Turns the 482 DriveRack™ on and off. Note: dbx Professional Products

recommends that power amps connected to the DriveRack™ should be

powered down prior to cycling the DriveRack™.

Page is loading ...

dbx 442 Owner's manual

Brand: dbx

Model: 442

Category: Audio equalizers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

dbx 442 Owner's manual

This manual is also suitable for

dbx 442 Owner's manual

Related papers

Other documents