2. Home
  3. Domestic appliances
  4. Sanitary ware
  5. Zip
  6. InLine Instantaneous Hot Water handwash kit 3kW

Zip InLine Instantaneous Hot Water handwash kit 3kW, InLine Instantaneous Hot Water handwash kit 4kW, InLine Instantaneous Hot Water handwash kit 6kW, InLine Instantaneous Hot Water handwashkit 4kW, InLine Instantaneous Hot Water handwash kit 3kW, InLine Instantaneous Hot Water handwash kit 4kW, InLine Instantaneous Hot Water handwash kit 6kW, InLine Instantaneous Hot Water handwashkit 4kW User manual

  • Hello! I am an AI chatbot trained to assist you with the Zip InLine Instantaneous Hot Water handwash kit 3kW User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
INSTALLATION INSTRUCTIONS & USER MANUAL
9120-14190 V1.00 NOV 2018 -ZIP ES/MT
TECHNICAL SUPPORT TEL: 0345 6 005 005 EMAIL: SERVICE@ZIPINDUSTRIES .CO.UK
WWW.ZIPWATER.CO.UK
Zip
InLine
Installation instructions & user manual
Model number:
ES/MT, ES4/MT, ES6/MT
Single lever mixer tap & fi ttings kit.
2
INSTALLATION INSTRUCTIONS & USER MANUAL
9120-14190 V1.00 NOV 2018 -ZIP ES/MT
TECHNICAL SUPPORT TEL: 0345 6 005 005 EMAIL: SERVICE@ZIPINDUSTRIES .CO.UK
WWW.ZIPWATER.CO.UK
SAFETY INFORMATION
WARNINGS
• These instructions must be read, fully understood and implemented, in conjunction
with the instructions provided with the ES instantaneous water heater.
• For guidance call Zip on 0345 6 005 005.
• The appliance must be disconnected from mains power supply before carrying out
any work involving live circuits.
• The appliance must be installed by a competent person familiar with electric
instantaneous water heaters.
• To prevent back-ow and contamination of the water supply for drinking and culinary
purposes, taps must provide an AUK2 or AUK3 air gap between the outlet & basin.
• The MT tap provides a type AUK2 air gap for domestic usage and a type AUK3 air
gap for non-domestic locations.
• An isolation valve with 15mm compression ttings should be installed on the cold
water supply pipe for connection to the hand wash pack and to enable future
maintenance.
!
!
TECHNICAL DATA
G3/8
G 1 1/4
50
130
80
60
105
90
Ø48
360
330
• ES Instantaneous water heater (see
instructions supplied with the ES
system).
• Tap type - basin mounted single lever
mixer tap.
• Mounting hole size Ø31-35mm.
• Pop up waste size 1 /1/4 inch.
• WRAS approved.
• Dimensions , see adjacent drawing.
Ø63
3
INSTALLATION INSTRUCTIONS & USER MANUAL
9120-14190 V1.00 NOV 2018 -ZIP ES/MT
TECHNICAL SUPPORT TEL: 0345 6 005 005 EMAIL: SERVICE@ZIPINDUSTRIES .CO.UK
WWW.ZIPWATER.CO.UK
INSTALLATION
InLine
ELEC TRONIC
6
7
1
4
3
5
8
9
10
2
9
1. ES Instantaneous water heater
2. Single lever mixer tap
3. 1/2” female to 3/8” male reducer
4.1/2” check valve
5. 15mm - 1/2” BSP braided hose
6. 1/2” male - 3/8” male reducer
7. 15mm - 1/2” ow adjuster
8. 15mm equal T piece
9. 15mm copper pipe (not supplied)
10.15mm isolating valve (not supplied)
• Secure the tap through the hole in the basin with the rubber washer, xing plate and nut
supplied. Install the pop up waste as required.
• Position the ES instantaneous water heater within comfortable reach of the braided hose from
the tap and install the heater according to its separate instructions.
• Connect the 1/2” check valve (4) and 1/2”-3/8” reducer (3) to the hot outlet connection on the
heater before connecting the hot supply braided hose from the tap.
• Run 15mm copper pipe from the isolation valve (10) to a convenient point within comfortable
reach of the cold supply braided hose from the tap and terminate with the T piece (8).
• Using a short length of copper tube from the side outlet of the T piece, connect the 15mm - 1/2”
ow adjuster (7) and the 1/2”- 3/8” reducer (6) before connecting the cold supply braided hose
from the tap.
• Using another length of copper tube from the T piece, connect the braided hose (5) to the cold
inlet connection of the heater.
• Ensure all braided hoses are not stretched, kinked, crushed or coiled and secure all pipework,
hoses and ttings as necessary to a convenient wall or cupboard side.
• Turn on the water supply & operate the tap and dispense water for two minutes.
• Check all connections for leaks and rectify as necessary.
• The ow adjuster (7) can be used to balance the hot and cold ow from the mixer tap.
• The MT taps have a high quality nish and should be treated with care.
• An occasional wipe with a mild soap on a soft damp cloth followed by a thorough rinse, is all
that is required.
• Do not use abrasive of chemical household cleaners, as this may cause damage.
Contents
Installation procedure
Maintenance
Warranty
• See instructions supplied with the ES instantaneous water heater.
4
INSTALLATION INSTRUCTIONS & USER MANUAL
9120-14190 V1.00 NOV 2018 -ZIP ES/MT
TECHNICAL SUPPORT TEL: 0345 6 005 005 EMAIL: SERVICE@ZIPINDUSTRIES .CO.UK
WWW.ZIPWATER.CO.UK
Zip Water UK
14 Bertie Ward Way, Dereham, Norfolk NR19 1TE
0345 6 005 005 sales@zipindustries.co.uk
www.zipwater.co.uk
/