HVS-6000_OU-SETUPGUIDE-E-4.DOC
HVS-6000/6000M
2120ROU/2240OU/2240OUA/3320OU
1. Connection
(1) Connect SDI video signal inputs.
(2) Input a reference signal. Terminate
the other connector with 75-ohm,
if it is not looped-through.
(3) Connect combined SDI video
signal outputs.
(4) Use a supplied LAN cable to connect
LAN1 (MAIN) ports on the HVS-6000/6000M (MU)
and the control panel (OU).
(5) Use a supplied LAN cable to connect
LAN2 (SUB) ports on the HVS-6000/6000M (MU)
and the control panel (OU)..
(6) Supply power to the MU and the OU respectively using the supplied AC power cables.
(7) Turn on power switch(es) on the OU rear panel.
(8) Turn on power switch(es) on the MU front panel.
3. Select System Signal Format
(1) A menu is displayed on the control panel at power ON.
(2) Tap the SETUP tab in the menu.
(3) Tap SYSTEM, then FORMAT to display the [SETUP > SYSTEM > FORMAT] menu.
(4) Turn F1 to select the signal format, then press F1.
(5) Turn F2 to select the aspect ratio.
(6) Tap REBOOT to display the [SETUP > SYSTEM > REBOOT] menu.
(7) Turn F1 to select EXEC under REBOOT, then press F1 to reboot the system.
After a restart, the new format is applied.
Precautions
- Operate the unit only at the specified supply voltage.
- Ensure the unit is properly grounded at all times.
- Ensure the power cord and connectors are firmly
connected.
- Do not install/uninstall cards with power applied to the
unit.
- Unit should not be operated or stored with the cover,
panels, and/or casing removed.
- Unit should not be operated or stored in a humid, dusty,
etc. environment. Doing so could result in fire or electrical
shock.
- Do not allow fluids, metal fragments, or any other foreign
objects to enter the unit. If foreign matter does enter the
unit, turn the power off and disconnect the power cord
immediately. Remove the material or contact your
authorized service representative.
- If you notice any strange smells or noises coming from the
unit, turn the power off immediately, disconnect the power
cord, then contact your authorized service representative.
4. Video Output
Select an M/E1PGM Video
Press a bus button on the M/E1PGM row.
The corresponding video will appear on M/E1 OUT1.
Select an M/E2PGM Video
Press a bus button on the M/E2PGM row.
The corresponding video will appear on M/E2 OUT1.
Select an AUX Video
(a) To output INPUT1 from AUX1, press AUX1, then 1 as shown below.
(b) To output the M/E1 program video from AUX12:
Press AUX12, then M/E1PGM as shown below. (HVS-2240OU)
While holding down AUX+10, press AUX2 twice quickly to display the menu, press M/E1. (HVS-2120ROU)
Press AUX12 twice quickly to display the menu, then turn F2 to select M/E1OUT1. (HVS-3320OU)
5. Background Transitions
(1) Select the next video on the PST bus.
(2) Press CUT to perform Cut transitions (with BKGD lit).
Press MIX then AUTO to perform Mix transitions.
Press WIPE then AUTO to perform Pattern transitions.
Faders can be used instead of AUTO .
* To select another transition pattern, press WIPE twice quickly to display the menu and turn F3 to select a pattern.
* After transitions, the background video will be replaced with a new one. As soon as the images are switched, the PGM and PST bus signals on the
control panel are also switched with each other.
6. Key Transitions
The following procedure example shows how to display a logo using KEY1.
Assume that the fill and key signals are respectively input IN11 and IN12.
(1) Select M/E1,2 DSK at top-left, then M/E2 KEY1 to display the [M/E1,2 DSK > M/E2 > KEY1 > SRC/INS]
menu.
(2) Turn F1 to change TYPE to BUS
(3) Turn F3 to select IN11. Turn F4 to select IN12.
(4) Press KEY1 ON AIR to cut in KEY1 into the PGM image. (The KEY1 ON AIR button lights up while KEY1 is displayed.)
(5) Press KEY1 AUTO to fade out KEY1 from the PGM image.
* KEY1-4 transitions can also be performed in the BKGD transition block.
MU Bundled Items
OU Bundled
2120
2240
3320
AC power cable
LAN cable
2
2
2
CD-ROM (User manual)
AC power cable
－
1
1
Quick Setup Guide (This guide)
AC adapter
1
－
－
Bus button partition plate
－
10
21
User button cover plate
－
－
10
Quick Setup Guide
28 29 30 31
14 15 16 17 18
USER BUTTON
USER BUTTON
NEXT TRANSITION
BK GD
KE Y1 KE Y2 KEY3 KE Y4
FADER LIMIT
MIX WIP E EF F1 EF F2
AUTO CUT
TR ANS
PREV REV NOR/REV DIR ECT
PAT TERN
KEY1 KEY2 KEY3 KEY4
DVE DVE DVE DVE
ON AIR
‚l^‚d@‚n‚t‚s
M/E 1 EXT INPUT 65~72INPUT 49~56INPUT 33~40INPUT 17~24INPUT 1~8AUXOUT 1~8 AUXOUT 17~24 M/E 3 GENLOCK
M/E OUT
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3 4
4
4
4
4
4
4
4 5
5
5
5
5
5 6
6
6
6
6
6 7
7
7
7
7
7 8
8
8
8
8
8
M/E OUT
REF IN TALLY OUT
LAN3
AC100-240V 50/60Hz IN
AC100-240V 50/60Hz IN
1
2
FAN 9
FAN 1 FAN 2 FAN 3 FAN 4
FAN 8FAN 7FAN 6FAN 5
ALARM
RS-422
1
2
3
4
5
6
RATING Label
AUXOUT 25~32 OPTIONEXT INPUT 73~80INPUT 57~64INPUT 41~48INPUT 25~32INPUT 9~16M/E 2AUXOUT 9~16
1
1
1
1
1
1 2
2
2
2
2
2
21
3
3
3
3
3
3
3 4
4
4
4
4
4 5
5
5
5
5
5 6
6
6
6
6
6
7
7
7
7
7
7 8
4
8
8
8
8
8
FAN 10
AC100-240V 50/60Hz IN
AC100-240V 50/60Hz IN
3
4
CPU
LAN1 LAN2
(MAIN) (SUB)
GPI IN
75-ohm termination
Video Server/VDR
AC power
source
HVS-6000 rear panel
AC power
source
SDI (M/E2 PGM)
SDI (M/E2 PVW)
SDI (M/E1 PGM)
SDI (M/E1 PVW)
Reference
GPI IN/TALLY OUT ON
OFF RATING LABLE
AC100-240 V 50/60Hz IN
POWER 2POWER 1
SER. NO.
POWER
CONTROL
MODE SW
LAN1USB LAN2
HDMIVGA (MAIN) (SUB)
MONITOR OUT
HVS-2240OU
GUI menu
(Midas Touch)
CK
AUX TRANSITION
CUT M IX W IPE
12
KEY/A UX 1110987654321
AUX
1 2 3 4 5 6 7 8 9 10 +10 +20
KEY1 KEY2 KEY3 KEY4 UT ILI TY
1 2 1 2 3 USE R BUTTON
4 5 6
HOLD SEL BUS
V
M/E1 M/ E2 M/E3
HVS-2240OU
HVS-2120ROU
HVS-3320OU
14 15 16 17 18 19 20 21 22 23 2410 11 12 135 6 7 8 91 2 3 4 25 26 27 28 29 30 31 32
14 15 16 17 1810 11 12 135 6 7 8 91 2 3 4
KEY1 KE Y2 KE Y3 KE Y4 UTL1 UTL2 AUX
KEY /AUX
M/E1 M/E2 MELite1 MEL ite2 MELite3 MELite4 MELite5 MELite6
LINE SELECT BUS
PGM OUT1 OUT2 OUT3
M/E1 PGM OUT1 OUT2 OUT3
M/E2
M V1
M V2
2423222120191817161514
OUT3OUT2OUT1PGM
M/ E1
M/ E2
PGM OUT1 OUT2 OUT 3
C UT M IX WI PE
AUX TRANSITION
1817
12111098765
AUX
KEY/AUX 13121110987654321
4321
KEY1 KEY2 KEY3 KEY4
16151413
HVS-6000
M/E1 OUT1-4
M/E2 OUT1-4
Operations on HVS-2120ROU /
3320OU are almost the same as
those on HVS-2240OU.
HVS-2240
OU
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
M/E1 PGM
M/E2 PGM
AUTO
Fader
PST row
CUT
14 15 16 17 18 19 20 21 22 23 2410 11 12 135 6 7 8 91 2 3 4
5 6 7 81 2 3 4 10 11 12 139
KEY/FLX
13 14 15 16 17 18 19 20 21 22 23 241 2 3 4 5 6 7 8 9 10 11 12
KEY1 KEY2 KEY3 KEY4 FLX1 FLX1FLX2 FLX3 BUS REC ATTACH DETACH
MACRO USER BUTTON
NEXT TRANSITIO N
KEY1 KEY2 KEY3 KEY4
BKGD
SEL BUS
MIX WIPE EFF1 EFF2
AUTO CUT
PREV
TRANS REV NOR/REV DIRECT
PATTERN
BUS DISP
HOLD
BUS FUNC
USER BUTTON
FADE R LIMIT
https://www.for-a.com/
You can download manuals and other documents by registering your email address.
HVS-6000_OU-SETUPGUIDE-E-4.DOC
HVS-6000/6000M
3355OU/OUA
1. Switcher Connection
(1) Connect SDI video signal inputs.
(2) Connect combined SDI video signal outputs.
(PGM / PVW) on the HVS-6000/6000M(MU).
(3) Use a supplied LAN cable to connect
MU LAN1 (MAIN) to LAN1(MAIN)
on the OU Control unit.
(4) Use a supplied LAN cable to connect
MU LAN2 (SUB) to LAN2(SUB)
on the OU Touch Panel.
(5) Use the supplied RS-422 cable to connect
the OU Control unit and OU Touch Panel.
(See Section 2 below for details.)
(6) Connect the OU AUX BUS unit and LINE
units to the OU Control units.
(See Section 2 below for details.)
(7) Supply AC power to the MU and OU
Control unit using the supplied AC cables.
(8) Connect the mouse and keyboard to the
OU Touch Panel, as necessary.
(9) Turn on the OU Touch Panel power switch.
Turn on the OU Control Unit power switch(es).
Turn on the MU power switch(es).
* To unplug power cables from the MU, wait until power indicators light orange after powered off.
2. Connecting OU Component Units
LAN Connection
Use the supplied LAN cables to connect the AUX
BUS and LINE units to the Control Unit respectively.
LINE 1, LINE 2 and LINE 3 are determined by the
connection ports on the Control Unit.
RS-422 Connection
Use the supplied RS-422 cable to connect the
Control Unit and the Touch Panel Unit.
Plug the cable to the TO TOUCH PANEL UNIT
port on the Control unit and the TO CONTROL
UNIT port on the Touch Panel.
Power Connection
Use the supplied DC canon cables to connect
the Control Unit and other units in a daisy chain.
The last LINE Unit (LINE2 or 3) must be directly
connected to the Control Unit and the Touch
Panel Unit must be the last device on the chain.
Do NOT plug or unplug power cords while the
power is on.
※ If using dedicated AC adapters, power can be directly
supplied to the AUX Unit, LINE Units and Touch Panel
In such cases, connect DC power cords to DC 12 V IN
terminals.
2. Setup
(1) Press the SYSTEM menu button. Tap the SYSTEM tab on the screen to display the [SETUP > SYSTEM > FORMAT] menu.
(2) Tap the FORMAT field. Turn F1 to select the signal format for use, then press F1.
(3) Tap REBOOT. Tap YES in the confirmation dialog to reboot the system. After a restart, the new format is applied.
3. Video Output
Select an M/E1PGM Video
Press a bus button on the M/E1PGM row.
The corresponding video will appear on
M/E1 OUT1.
Select an M/E2PGM Video
Press a bus button on the M/E2PGM row.
The corresponding video will appear on
M/E2 OUT1.
4. Background Transitions
To perform M/E background transitions, proceed as follows:
(1) Select the next video on the PST bus.
(2) Press CUT to perform Cut transitions.
Press MIX and AUTO to perform Mix transitions.
Press WIPE and AUTO to perform Pattern transitions.
Also move the fader from end to end to perform transitions.
* To select another pattern, press WIPE twice quickly to display the corresponding menu. And turn F3 to select a pattern.
* Performing transitions replace the background video with the next one and switch the PGM and PST bus signal selections.
5. Key Transitions
As an example, follow the procedure below to insert a logo using
M/E2 KEY1.
Assume that IN11 and IN12 accept logo fill and key signals respectively.
(1) Press menu tabs in the following order on the menu screen to display
the [FUNCTION > KEYER DSK > SRC/INS > M/E2] menu.
(2) Turn F1 to select BUS for TYPE.
(3) Turn F2 to select IN11 for INSERT SIGNAL (fill).
(4) Turn F1 to select IN12 for SOURCE SIGNAL (key).
(5) Press KEY1 ON AIR to cut in the logo on the PGM image.
(KEY1 ON AIR lights during the logo is displayed.)
(6) Press KEY1 AUTO to fade out the logo from the PGM image.
MU Bundled Items
HVS-3355OU/OUA
AC power cable
<OU component units>
<Other items>
Rack mount brackets (Installed)
Control Unit
1
LAN cable
6
CD-ROM (User manual)
Touch Panel Unit
1
RS-422 cable
1
Quick Setup Guide (This guide)
AUX BUS Unit
1
AC power cable
1
LINE Unit
3
DC Canon cable
5
Rack mount brackets
1
HVS-6000
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
FLX FLX FLX
FLX FLX
1 21 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18
16 17 18 1 2 3
FLX
3
FLX FLX
4
4DSK
DSK
DSK
DSK
DSK
DSK
DSK
DSK
1 2 3 4
1 2 3 4
MACRO
MACRO
MACRO
MACRO
MACRO MACRO MACRO MACRO
REC ATTACH DETACH CHECK
DISP SHIFT SHIFT
2 3
INHI
CUT
CUT
MIX
MIX
WIPE
WIPE
SRC HOLD LDVE SEL
SRC HOLD LDVE
SEL
SEL
DISP SHIFT
2SHIFT
3 BUS
INHI
HOLD
HOLD
LDVE
LDVE LOCK
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
EFF
2
1
NOR
REV
NOR
/REV
LIMIT
AUTOCUT
SRC
SRC
HOLD
HOLD
SHIFT
DISP 2SHIFT
3
LDVE
LDVE
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK
INHI
SRC
SRC
DISP
INHI
HOLD
HOLD
SHIFT
LDVE
LDVE
SHIFT
2 3
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK CUT AUTO
EFF
EFF
2
1
LIMIT
NOR
/REV
MIX
WIPE
NOR
REV
TRNS
KEY
PAD
-
MACRO
PATTERN
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
1
EFF
2
NOR
REV
NOR
/REV
LIMIT
AUTOCUT
TRANS
KEY
PAD
-
CLR
CLR
EVENT
SEQ
EVENT
SEQ
MACRO
PATTERN
DISPLAY
DISPLAY
DVE
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
KEY1
KEY1
KEY2
KEY2
KEY3 KEY4
KEY4KEY3
1
KEY1 KEY2
KEY1 KEY2
KEY3 KEY4
KEY3 KEY4
1 2 3 4
5 6 7 8
KEY1 KEY2 KEY3 KEY4
2 3 4
5 6 7 8
CONTROL
SEQDSKFLXME3ME2ME1
CTRL
REV
NOR
/REV
LIMIT
KEY3
KEY4
KEY2
KEY1
CUT AUTO
DVE
FLX1 FLX4FLX3FLX2
DSK1 DSK2 DSK3 DSK4
FLX1 FLX2 FLX3 FLX4
DISPLAY
DSK1 DSK2 DSK3 DSK4
1 2 3 4
5 6 7 8
DISPLAY
EVENT
MACRO
SEQ
PATTERN
-
KEY
PAD
TRANS
CLR
DIGITAL VIDEO SWITCHER
TOP
KEY1 KEY2 KEY3 KEY4
12
12
AUX A UX AUX AUX A UX AUX AUX A UX AUX A UX AUX AUX A UX AUX AUX A UX AUX AUX
AUX A UX AUX AUX A UX AUX AUX A UX AUX A UX AUX AUX A UX AUX AUX A UX AUX AUX
FLX FLX FLX
FLX FLX
1 21 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18
16 17 18 123
FLX
3
FLX FLX
4
4DSK
DSK
DSK
DSK
DSK
DSK
DSK
DSK
1 2 3 4
1 2 3 4
MACRO
MACRO
DVE
FLX1 FLX4FLX3FLX2
DSK1 DSK2 DSK3 DSK4
FLX1 FLX2 FLX3 F LX4
DISPLAY
DSK1 DSK2 DSK3 DSK4
CONTROL
SEQDSKFLXME3M E2ME1
CTRL
REV
NOR
/REV
LIMIT
KEY3
KEY4
KEY2
KEY1
CUT AUTO
DIGITAL VIDEO SWITCHE R
TOP
CUT AUTO
EFF
EFF
2
1
LIMIT
NOR
/REV
MIX
WIPE
NOR
REV
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
1
EFF
2
NOR
REV
NOR
/REV
LIMIT
AUTOCUT
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
EFF
2
1
NOR
REV
NOR
/REV
LIMIT
AUTOCUT
EVENT
MACRO
SEQ
PATTERN
-
KEY
PAD
TRANS
CLR
TRNS
KEY
PAD
-
MACRO
PATTERNCLR
EVENT
SEQ
TRANS
KEY
PAD
-
CLR
EVENT
SEQ
MACRO
PATTERN
‚j‚d‚x‚P ‚j‚d‚x‚Q ‚j‚d‚x‚R ‚j‚d‚x‚S
KEY1 KEY2 KEY4KEY3
1 2 3 4
5 6 7 8
DISPLAY
DISPLAY
KEY1 KEY2 KEY3 KEY4
1
KEY1 KEY2 KEY3 KEY4
234
5 6 7 8
DISPLAY
KEY1 KEY2
KEY1 KEY2
KEY3 KEY4
KEY3 KEY4
1 2 3 4
5 6 7 8
SRC
SRC
DISP
INHI
HOLD
HOLD
SHIFT
LDVE
LDVE
SHIFT
2 3
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK
SRC
SRC
HOLD
HOLD
SHIFT
DISP 2SHIFT
3
LDVE
LDVE
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK
INHI
SRC HOLD LDVE SEL
SRC HOLD LDVE
SEL
SEL
DISP SHIFT
2SHIFT
3 BUS
INHI
HOLD
HOLD
LDVE
LDVE LOCK
MACRO MACR O MACRO MACRO
REC ATTACH D ETACH CHECK
2 3
INHI
CUT
CUT
MIX
MIX
WIPE
WIPE
DVE
DISP SHIFT SHIFT
USER
USER
M/E1 PGM
M/E2 PGM
M/E1 OUT1-4
M/E2 OUT1-4
SRC
SRC
DISP
INHI
HOLD
HOLD
SHIFT
LDVE
LDVE
SHIFT
2 3
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK CUT AUTO
EFF
EFF
2
1
LIMIT
NOR
/REV
MIX
WIPE
NOR
REV
DVE KEY1 KEY2 KEY4KEY3
1 2 3 4
5 6 7 8
DISPLAY
EVENT
MACRO
SEQ
PATTERN
-
KEY
PAD
TRANS
CLR KEY1 KEY2 KEY3 KEY4
DVE
FLX1 FLX2 FLX3 FLX4
KEY5 KEY6 KEY7 KEY8
DISPLAY
FLX1 FLX2 FLX3 FLX4
KEY5 KEY6 KEY7 KEY8
PGM PST KEY1 KEY2 KEY3 KEY4
AUTO
Fader
PST row
CUT
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
FLX FLX FLX
FLX FLX
1 21 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18
16 17 18 1 2 3
FLX
3
FLX FLX
4
4DSK
DSK
DSK
DSK
DSK
DSK
DSK
DSK
1 2 3 4
1 2 3 4
MACRO
MACRO
MACRO
MACRO
MACRO MACRO MACRO MACRO
REC ATTACH DETACH CHECK
DISP SHIFT SHIFT
2 3
INHI
CUT
CUT
MIX
MIX
WIPE
WIPE
SRC HOLD LDVE SEL
SRC HOLD LDVE
SEL
SEL
DISP SHIFT
2SHIFT
3 BUS
INHI
HOLD
HOLD
LDVE
LDVE LOCK
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
EFF
2
1
NOR
REV
NOR
/REV
LIMIT
AUTOCUT
SRC
SRC
HOLD
HOLD
SHIFT
DISP 2SHIFT
3
LDVE
LDVE
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK
INHI
SRC
SRC
DISP
INHI
HOLD
HOLD
SHIFT
LDVE
LDVE
SHIFT
2 3
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK CUT AUTO
EFF
EFF
2
1
LIMIT
NOR
/REV
MIX
WIPE
NOR
REV
TRNS
KEY
PAD
-
MACRO
PATTERN
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
1
EFF
2
NOR
REV
NOR
/REV
LIMIT
AUTOCUT
TRANS
KEY
PAD
-
CLR
CLR
EVENT
SEQ
EVENT
SEQ
MACRO
PATTERN
DISPLAY
DISPLAY
DVE
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
KEY1
KEY1
KEY2
KEY2
KEY3 KEY4
KEY4KEY3
1
KEY1 KEY2
KEY1 KEY2
KEY3 KEY4
KEY3 KEY4
1 2 3 4
5 6 7 8
KEY1 KEY2 KEY3 KEY4
2 3 4
5 6 7 8
CONTROL
SEQDSKFLXME3ME2ME1
CTRL
REV
NOR
/REV
LIMIT
KEY3
KEY4
KEY2
KEY1
CUT AUTO
DVE
FLX1 FLX4FLX3FLX2
DSK1 DSK2 DSK3 DSK4
FLX1 FLX2 FLX3 FLX4
DISPLAY
DSK1 DSK2 DSK3 DSK4
1 2 3 4
5 6 7 8
DISPLAY
EVENT
MACRO
SEQ
PATTERN
-
KEY
PAD
TRANS
CLR
DIGITAL VIDEO SWITCHER
TOP
KEY1 KEY2 KEY3 KEY4
CUT AUTO
EFF
EFF
2
1
LIMIT
NOR
/REV
MIX
WIPE
NOR
REV
DVE
PGM PST KEY1 KEY2 KEY3 KEY4 KEY1 KEY2 KEY4KEY3
DVE
FLX1 FLX4FLX3FLX2
DSK1 DSK2 DSK3 DSK4
FLX1 FLX2 FLX3 FLX4
DISPLAY
DSK1 DSK2 DSK3 DSK4
1 2 3 4
5 6 7 8
DISPLAY
EVENT
MACRO
SEQ
PATTERN
-
KEY
PAD
TRANS
CLR KEY1 KEY2 KEY3 KEY4
RATING LABEL 1
2
AC100-240V 50/60Hz IN
TO TOUCH PANEL UNITLINE4LINE3LINE2LINE1OPTIONAUX
GPI IN/TALLY OUT
DC OUTPUT (DC48V)
OUT 1 SERVICE
UNIT CONTROL
LAN 1 (MAIN)
RATING LABEL
To MU
LAN2 (SUB) port
Touch Panel
Supplied DC canon cables (Standard: 1 m)
Supplied LAN cables
(Standard: 3 m)
(Standard
10 m)
Supplied RS-422 cable (Standard: 10 m)
Control Unit
To MU LAN1 (MAIN) port
AC power source
LINE unit (LINE 3)
LINE unit (LINE 2)
LINE unit (LINE 1)
AUX BUS unit
Control
Control Unit Ethernet
DC 12 V IN
SERVICE / CTRL
Quick Setup Guide
‚l^‚d@‚n‚t‚s
M/E 1 EXT INPUT 65~72INPUT 49~56INPUT 33~40INPUT 17~24INPUT 1~8AUXOUT 1~8 AUXOUT 17~24 M/E 3 GENLOCK
M/E OUT
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3 4
4
4
4
4
4
4
4 5
5
5
5
5
5 6
6
6
6
6
6 7
7
7
7
7
7 8
8
8
8
8
8
M/E OUT
REF IN TALLY OUT
LAN3
AC100-240V 50/60Hz IN
AC100-240V 50/60Hz IN
1
2
FAN 9
FAN 1 FAN 2 FAN 3 FAN 4
FAN 8FAN 7FAN 6FAN 5
ALARM
RS-422
1
2
3
4
5
6
RATING Label
AUXOUT 25~32 OPTIONEXT INPUT 73~80INPUT 57~64INPUT 41~48INPUT 25~32INPUT 9~16M/E 2AUXOUT 9~16
1
1
1
1
1
1 2
2
2
2
2
2
21
3
3
3
3
3
3
3 4
4
4
4
4
4 5
5
5
5
5
5 6
6
6
6
6
6
7
7
7
7
7
7 8
4
8
8
8
8
8
FAN 10
AC100-240V 50/60Hz IN
AC100-240V 50/60Hz IN
3
4
CPU
LAN1 LAN2
(MAIN) (SUB)
GPI IN
RATING LABEL 1
2
AC100-240V 50/60Hz IN
TO TOUCH PANEL UNITLINE4LINE3L INE2LINE1OPTIONAUX
GPI IN/TALLY OUT
DC OUTPUT (DC48V)
OUT 1 SERVICE
UNIT CONTROL
LAN 1 (MAIN)
75-ohm termination
Video Server
To AC
power
source
HVS-6000 rear side
OU Control
unit
To AC power
source
SDI (M/E2 PGM)
SDI (M/E2 PVW)
SDI (M/E1 PGM)
SDI (M/E1 PVW)
Reference
F4F3F2F1
RESET USB2USB1
OU Touch Panel
https://www.for-a.com/
You can download manuals and other documents by registering your email address.
-
1
-
2
