HVS-2000_OU-SETUPGUIDE-E-6.DOCX
HVS-2000
2120ROU/2240OU/2240OUA/3320OU
1. Connection
(1) Connect SDI video signal inputs.
(2) Input a reference signal. Terminate the other connector with 75-ohm, if it is not looped-through.
(3) Connect combined SDI video signal outputs.
(4) Use the supplied LAN cable to connect HVS-2000 LAN1 (MAIN) to LAN1(MAIN) on the control panel.
(5) Use the supplied LAN cable to connect HVS-2000 LAN2 (SUB) to LAN2(SUB) on the control panel.
(6) Supply power to HVS-2000 and the control panel respectively using the supplied AC cables.
(7) Turn on power switch(es) on the control rear panel.
(8) Turn on power switch(es) on the HVS-2000 front panel.
* HDMI outputs (AUX13 and AUX14) can display input sources, as well as combined images such as preview,
program or multiview.
* An Ethernet hub can be used for LAN1 and LAN2 connections.
* Internal GUI menu operation, which is linked with the panel menu, is available by connecting a monitor to the HDMI
or VGA connector on the control panel.
2. Setup
Select the System Signal Format
(1) The touch panel menu is displayed on the control panel at power ON.
(2) Tap the SETUP tab in the menu display.
(3) Tap SYSTEM, then FORMAT to display the [SETUP > SYSTEM > FORMAT] menu.
(4) Turn F1 to select the signal format, then press F1.
(5) Turn F2 to select the aspect ratio.
(6) Tap REBOOT to display the [SETUP > SYSTEM > REBOOT] menu.
(7) Turn F1 to select EXEC under REBOOT, then press F1 to reboot the system.
After a restart, the new format is applied.
* All inputs are equipped with a frame synchronizer. Open the [SYSTEM > INPUT > SIGNAL] menu and turn on FS,
as needed. (Turn F1 to select an input, then turn F4 to set FS to ON.)
* Open the [SETUP > SYSTEM > TIME] menu to set date and time.
3. Select Output Video
Select an M/E1PGM Video
Press a bus button on the M/E1PGM row.
The corresponding video will appear on M/E OUT1.
Select an M/E2PGM Video
Press a bus button on the M/E2PGM row.
The corresponding video will appear on M/E OUT3.
Select an AUX Video
(a) To output INPUT1 from AUX1, press AUX1, then 1 as shown below.
(b) To output the M/E1 program video from AUX12:
Press AUX12, then M/E1PGM as shown below. (HVS-2240OU)
While holding down AUX+10, press AUX2 twice quickly to display the menu, press M/E1. (HVS-2120ROU)
Press AUX12 twice quickly to display the menu, then turn F2 to select M/E1OUT1. (HVS-3320OU)
4. Perform Background Transitions
(1) Select the next video on the PST bus.
(2) Verify that BKGD lights up as shown at right. If not, press the button to turn on the button light.
(3) Press CUT to perform Cut transitions or perform Mix or Pattern transitions. (See below instructions.) Then the background video will be replaced with
a new one. As soon as the images are switched, the PGM and PST bus signals on the control panel are also switched with each other.
To Perform MIX Transitions
(3) Press MIX. Then press AUTO.
(Or move the fader from end to end.)
To Perform Pattern Transitions
(3) Press WIPE.
(4) Press BKGD twice quickly to display the [M/E1,2 FLEXaKEY
> M/E2 > BKGD PGM > TRANS SUB EFF > TRANS] menu.
(5) Turn F3 to select a pattern.
(6) Press AUTO. (Or move the fader from end to end.)
Precautions
- Operate the unit only at the specified supply voltage.
- Ensure the unit is properly grounded at all times.
- Ensure the power cord and connectors are firmly connected.
- Do not install/uninstall cards with power applied to the unit.
- Unit should not be operated or stored with the cover, panels, and/or casing
removed.
- Unit should not be operated or stored in a humid, dusty, etc.
environment. Doing so could result in fire or electrical shock.
- Do not allow fluids, metal fragments, or any other foreign objects to
enter the unit. If foreign matter does enter the unit, turn the power off
and disconnect the power cord immediately. Remove the material or
contact your authorized service representative.
- If you notice any strange smells or noises coming from the unit, turn
the power off immediately, disconnect the power cord, then contact
your authorized service representative.
Quick Setup Guide
GPI IN/TALLY OUT ON
OFF RATING LABLE
AC100-240 V 50/60Hz IN
POWER 2POWER 1
SER. NO.
POWER
CONTROL
MODE S W
LAN1USB LAN2
HDMIVGA (MAIN) (SUB)
MONIT OR OUT
HD/SD SDI (M/E2 PGM)
HD/SD SDI (M/E1 PGM)
75-ohm termination
Reference signal
AC power source
AC1 0 0 - 24 0 V 50 /60 H z I N
PS1
PS2
AC1 00 - 2 4 0 V 5 0/6 0H z I N
CPU
I/O 1
I/O 2
I/O A
I/O B
A UX
2 3 4 1 2 3 4 5 6 7 8 9 10 11 121M/E
SDI OUTPUT
3 4 521
REF OUT
6
LAN1
(MAIN)
GPI IN TALLY OUT
RS-422
ARCNET LAN2
RE F IN GENLOCK
(SU B)
1 2 3 54 6 7 8 9 10 11 12
SDI IN PUT HDMI OUT1
SDI IN PUT HDMI OUT2
13 14 15 16 17 18 19 20 21 22 23 24
IN A IN B
IN C IN D
OPTION SLOT
SER. NO.
Preview
AC power source
Internal
GUI menu
Video server
etc.
HD/SD
SDI
Operations on HVS-2120ROU /
3320OU are almost the same
as those on HVS-2240OU.
HVS-2000 bundled items
OU bundled items
2120
2240
3320
AC Cable
1
LAN cable
2
2
2
Rack mount brackets
1
AC Cable
－
1
1
CD-ROM (User Manuals)
1
AC Adapter
1
2
Quick Setup Guide (this guide)
1
Bus button partition plates
－
10
21
User button cover plates
－
－
10
HVS-2000
HVS-2240OU
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
M/E2PGM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
M/E1PGM
2 3 41 M/E
2 3 41 M/E
BKGD
KEY1 KEY2 KEY3 KEY4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
MIX WIPE EF F1 E FF 2
AUTO CUT
TRANS RE V
FADER LI MIT
PREV
BUS DISP
BUS F UNC
NEXT TRANSITION
NOR/REV DIRECT
PAT TERN
KEY1
DVE
ON AIR
DVE
KEY2
19 20
KEY1 KEY2 KEY3 KEY4 FLX1 FLX2 FLX3 FLX4 BUS REC ATTA CH DETA CH
MACRO
KEY/FLX
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 4 5SEL BUS
HOLD
1 2 876543 USER BU TTON 3
USER BU TTON
AUTO
Fader
CK
AUX TRANSITION
CUT M IX W IPE
12
KEY/A UX 1110987654321
AUX
1 2 3 4 5 6 7 8 9 10 +10 +20
KEY1 KEY2 KEY3 KEY4 UT ILI TY
1 2 1 2 3 USER BUT TON
4 5 6
HOLD SEL BUS
V
M/E1 M/ E2 M/E3
HVS-2240OU
HVS-2120ROU
HVS-3320OU
14 15 16 17 18 19 20 21 22 23 2410 11 12 135 6 7 8 91 2 3 4 25 26 27 28 29 30 31 32
14 15 16 17 1810 11 12 135 6 7 8 91 2 3 4
KEY1 KE Y2 KEY3 KEY4 UTL1 UTL2 AUX
KEY /AUX
M/E1 M/E2 MELite1 MELite2 MELite3 MELite4 MELite5 MELite6
LINE SELECT BUS
PGM OUT1 OUT2 OUT3
M/E1 PGM OUT1 OUT2 OUT3
M/E2
M V1
M V2
2423222120191817161514
OUT3OUT2OUT1PGM
M/ E1
M/ E2
PGM OUT1 OUT2 OUT 3
C UT M IX WI PE
AUX TRANSITION
1817
12111098765
AUX
KEY/AUX 13121110987654321
4321
KEY1 KEY2 KEY3 KEY4
16151413
https://www.for-a.com/
You can download manuals and other documents by registering your email address.
HVS-2000_OU-SETUPGUIDE-E-6.DOCX
HVS-2000
391OU/392OU/ROU/WOU
1. Connection
(1) Connect SDI video signal inputs.
(2) Input a reference signal. Terminate the other connector with 75-ohm, if it is not looped-through.
(3) Connect combined SDI video signal outputs.
(4) Connect monitors through HDMI ports for monitoring (Preview and Multi-view images)
(5) Use the supplied connection cable to connect HVS-2000 and the control panel through Arcnet.
(6) Supply power to HVS-2000 and the control panel respectively using the supplied AC cables.
(7) Use LAN2(SUB) on the control panel to connect to the HVS-2000 GUI through LAN.
(8) Turn on power switch(es) on the control rear panel.
(9) Turn on power switch(es) on the HVS-2000 front panel.
* HDMI outputs (AUX13 and AUX14) can display input sources, as well as combined images such as preview,
program or multiview.
* An Ethernet hub can be used for LAN2 connections.
2. Setup
Select the System Signal Format
(1) Tap the SYSTEM tab in the left side of the HVS-2000GUI menu screen to open the [SETUP > SYSTEM > FORMAT] menu.
(2) Select the signal format under FORMAT.
(3) Select the aspect ratio under Aspect.
(4) Tap MU REBOOT, then YES in the confirmation dialog.
(5) After a restart, the new format is applied.
* All inputs are equipped with a frame synchronizer. Open the [SYSTEM > INPUT > SIGNAL] menu and turn on FS, as needed.
* Open the [SETUP > SYSTEM > TIME] menu to set date and time.
* HVS-2000GUI software is required for system setup. Install the GUI to a computer from the supplied CD-ROM using a purchased software license.
3. Select Output Video
Select an M/E1PGM Video
Press a bus button on the M/E1PGM row.
The corresponding video will appear on M/E OUT1.
Select an M/E2PGM Video
Press a bus button on the M/E2PGM row.
The corresponding video will appear on M/E OUT3.
4. Perform Background Transitions
(1) Select the next video on the PST bus.
(2) Verify that BKGD lights up as shown at right.
If not, press the button to turn on the button light.
(3) Press CUT to perform Cut transitions or perform
Mix or Pattern transitions. (See below instructions.)
Then the background video will be replaced with
a new one. As soon as the images are switched,
the PGM and PST bus signals on the control panel are also switched with each other.
To Perform MIX Transitions
(3) Press MIX. Then press AUTO. (Or move the fader from end to end.)
To Perform Pattern Transitions
(3) Press WIPE.
(4) Open the [FUNCTION > TRANS > TRANS] menu.
(5) Select a pattern.
(6) Press AUTO. (Or move the fader from end to end.)
Precautions
- Operate the unit only at the specified supply voltage.
- Ensure the unit is properly grounded at all times.
- Ensure the power cord and connectors are firmly connected.
- Do not install/uninstall cards with power applied to the unit.
- Unit should not be operated or stored with the cover, panels, and/or casing
removed.
- Unit should not be operated or stored in a humid, dusty, etc.
environment. Doing so could result in fire or electrical shock.
- Do not allow fluids, metal fragments, or any other foreign objects to
enter the unit. If foreign matter does enter the unit, turn the power off
and disconnect the power cord immediately. Remove the material or
contact your authorized service representative.
- If you notice any strange smells or noises coming from the unit, turn
the power off immediately, disconnect the power cord, then contact
your authorized service representative.
Quick Setup Guide
HVS-2000 bundled items
390 Series OU bundled items
AC Cable
1
AC cable
1
Rack mount brackets
1
Control Cable (BNC)
1
CD-ROM (User Manuals)
1
Quick Setup Guide (This guide)
1
HVS-2000GUI software license (option)
1
Operations on HVS-392OU/ROU/WOU
are almost the same. (HVS-391OU has
only one M/E.)
HVS-2000
HVS-392OU
2 3 41 M/E
2 3 41 M/E
M/E2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 M/E
M/E2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 M /E
M/E2PGM
M/E1PGM
M/E2
12345678910 11 12 13 14 15 16 17 18 19 20 M/E
REV NOR /REV
DIRECTION
PATTERN
BKGD KEY1 KEY2
KEY3 KEY4
NEXT TRANSITION
TRANSITION TYPE
MIX WIPE
AUT O CUT
ON AI R
DVE
KEY 2
KEY 1
KEY 3
KEY 4
DVE
DVE
DVE
FADER LIMIT
AUTO
Fader
HD/SD SDI (M/E2 PGM)
HD/SD SDI (M/E1 PGM)
75-ohm termination
Reference signal
AC power
source
AC1 0 0 - 2 40 V 5 0 /60 H z I N
PS1
PS2
AC1 0 0- 2 40 V 5 0 /60 H z I N
CPU
I/O 1
I/O 2
I/O A
I/O B
A UX
2 3 4 1 2 3 4 5 6 7 8 9 10 11 121M/E
SDI OUTPUT
3 4 521
REF OUT
6
LAN1
(MAIN)
GPI IN TALLY OUT
RS-422
ARCNET LAN2
RE F IN GENLOCK
(SU B)
1 2 3 54 6 7 8 9 10 11 12
SDI IN PUT HDMI OUT1
SDI IN PUT HDMI OUT2
13 14 15 16 17 18 19 20 21 22 23 24
IN A IN B
IN C IN D
OPTI ON SLOT
SER. NO.
Video server,
etc.
HD/SD SDI
AC power
source
RATING LABEL
CONTROL TO MU GPI/TALLY OUT
(SERVICE)
AC100-240V 50/60Hz IN
POWE R 1
POWERON
OFF
POWER 2
Preview
image
Multiview
image
75-ohm termination
HVS-2000
GUI
(option)
https://www.for-a.com/
You can download manuals and other documents by registering your email address.
HVS-2000_OU-SETUPGUIDE-E-6.DOCX
HVS-2000
HVS-3355OU/OUA
1. MU and OU Connection
(1) Connect SDI video signal inputs.
(2) Input a reference signal. Terminate the other connector with 75-ohm, if it is not looped-through.
(3) Connect combined SDI video signal outputs.
(4) Connect a monitor display through HDMI (for monitoring PREVIEW or Multiview images)
(5) Connect the Main Unit (MU) and OU Control Unit using supplied LAN cables. Connect LAN1 (MAIN) ports.
(6) Connect MU and OU Touch Panel Unit using supplied LAN cables. Connect LAN2 (SUB) ports.
(7) Connect OU Control Unit and OU Touch Panel Unit using the supplied RS-422 cable. Connect the TO GUI UNIT
port on the OU Control Unit to the TO CONTROL UNIT port on the OU Touch Panel.
(8) Connect the OU AUX BUS Unit and OU LINE Units to the OU Control Unit. (See the back page)
(9) Use supplied AC power cables to supply AC power to the MU and OU Control Unit.
(10) Connect a mouse and keyboard to USB ports on the OU Touch Panel Unit, as necessary.
* See the back page for more details on OU component connection.
2. Setup
Select the System Signal Format
(1) Press the SYSTEM menu button on the left side of the touch panel. Tap
the SYSTEM tab in the touch panel screen to display [SETUP > SYSTEM
> SYSTEM] menu.
(2) Turn F1 to select a video signal format under FORMAT.
(3) Turn F2 to select an aspect ratio under ASPECT.
(4) Tap MU REBOOT. A confirmation dialog box appears. Tap YES to reboot
the system. After a restart, the new format is applied.
* All inputs are equipped with a frame synchronizer. Open the [SYSTEM >
INPUT > SIGNAL] menu and turn on FS, as needed. (Turn F1 to select an
input, then turn F4 to set FS to ON.)
* Open the [SETUP > SYSTEM > TIME] menu to set date and time.
3. Select Output Video
Select an M/E1PGM Video
Press a bus button on the M/E1PGM row.
The corresponding video will appear on M/E OUT1.
Select an M/E2PGM Video
Press a bus button on the M/E2PGM row.
The corresponding video will appear on M/E OUT3
4. Perform Background Transitions
The following procedure shows how to perform M/E2
background transitions as an example.
(1) Select the next video on the PST bus.
(2) Press CUT to perform Cut transitions.
Press MIX, then AUTO to perform Mix transitions.
Press WIPE, then AUTO to perform Pattern transitions.
Transitions can be performed by moving the fader from end to end, instead of pressing AUTO.
* To select another transition pattern, press WIPE twice quickly to display the menu and turn F3 to select a pattern.
* After transitions, the background video will be replaced with a new one. As soon as the images are switched, the PGM and PST bus signals on the
control panel are also switched with each other.
HVS-2000 Bundled Items
AC Cable (2)
Rack mount brackets (1)
HVS-2000PSM (1) (Installed)
CD-ROM (User Manuals) (1)
Setup Guide (This guide) (1)
HVS-2000GUI software license (option)
<Other Accessories>
LAN Cable (6)
RS-422 Cable (1)
AC Power Cable (1)
DC Power Cable (Cannon) (5)
Rack mount brackets for OU (1)
Quick Setup Guide
HVS-3355OU/OUA Bundled Items
<OU Component Units>
Control Unit (1)
Touch Panel Unit (1)
AUX BUS Unit (1)
LINE Unit (3)
AUX AUX AUX A UX AUX AUX A UX AUX AUX A UX AUX AUX AUX AUX AUX A UX AUX AUX
AUX AUX AUX A UX AUX AUX A UX AUX AUX A UX AUX AUX AUX AUX AUX A UX AUX AUX
FLX FLX FLX
FLX FLX
1 21 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18
16 17 18 123
FLX
3
FLX FLX
4
4DSK
DSK
DSK
DSK
DSK
DSK
DSK
DSK
1 2 3 4
1 2 3 4
MACRO
MACRO
DVE
FLX1 FLX4FLX3FLX2
DSK1 DSK2 DSK3 DSK4
FLX1 F LX2 FLX3 FLX4
DISPLAY
DSK1 DSK2 DSK3 DSK4
CONTROL
SEQDSKFLXME3ME2ME1
CTRL
REV
NOR
/REV
LIMIT
KEY3
KEY4
KEY2
KEY1
CUT AUTO
DIGITAL VI DEO SW ITCHER
TOP
CUT AUTO
EFF
EFF
2
1
LIMI T
NOR
/REV
MIX
WIPE
NOR
REV
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
1
EFF
2
NOR
REV
NOR
/REV
LIMI T
AUTOCUT
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
EFF
2
1
NOR
REV
NOR
/REV
LIMI T
AUTOCUT
EVENT
MACRO
SEQ
PATTERN
-
KEY
PAD
TRANS
CLR
TRNS
KEY
PAD
-
MACRO
PATTERNCLR
EVENT
SEQ
TRANS
KEY
PAD
-
CLR
EVENT
SEQ
MACRO
PATTERN
‚j‚d‚x‚P ‚j‚d‚x‚Q ‚j‚d‚x‚R ‚j‚d‚x‚S
KEY1 KEY2 KEY4KEY3
1 2 3 4
5 6 7 8
DISPLAY
DISPLAY
KEY1 KEY2 KEY3 KEY4
1
KEY1 KEY2 KEY3 KEY4
234
5 6 7 8
DISPLAY
KEY1 KEY2
KEY1 KEY2
KEY3 KEY4
KEY3 KEY4
1 2 3 4
5 6 7 8
SRC
SRC
DISP
INHI
HOLD
HOLD
SHIFT
LDVE
LDVE
SHIFT
2 3
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK
SRC
SRC
HOLD
HOLD
SHIFT
DISP 2SHIFT
3
LDVE
LDVE
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK
INHI
SRC HOLD LDVE SEL
SRC HOLD LDVE
SEL
SEL
DISP SHIFT
2SHIFT
3 BUS
INHI
HOLD
HOLD
LDVE
LDVE LOCK
MACRO MACRO MACRO MACRO
REC ATTACH DETACH CH ECK
2 3
INHI
CUT
CUT
MIX
MIX
WIPE
WIPE
DVE
DISP SHIFT SHIFT
USER
USER
HVS-2000
M/E2PGM
M/E1PGM
2 3 41 M/E
2 3 41 M/E
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
FLX FLX FLX
FLX FLX
1 21 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18
16 17 18 1 2 3
FLX
3
FLX FLX
4
4DSK
DSK
DSK
DSK
DSK
DSK
DSK
DSK
1 2 3 4
1 2 3 4
MACRO
MACRO
MACRO
MACRO
MACRO MACRO MACRO MACRO
REC ATTACH DETACH CHECK
DISP SHIFT SHIFT
2 3
INHI
CUT
CUT
MIX
MIX
WIPE
WIPE
SRC HOLD LDVE SEL
SRC HOLD LDVE
SEL
SEL
DISP SHIFT
2SHIFT
3 BUS
INHI
HOLD
HOLD
LDVE
LDVE LOCK
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
EFF
2
1
NOR
REV
NOR
/REV
LIMIT
AUTOCUT
SRC
SRC
HOLD
HOLD
SHIFT
DISP 2SHIFT
3
LDVE
LDVE
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK
INHI
SRC
SRC
DISP
INHI
HOLD
HOLD
SHIFT
LDVE
LDVE
SHIFT
2 3
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK CUT AUTO
EFF
EFF
2
1
LIMIT
NOR
/REV
MIX
WIPE
NOR
REV
TRNS
KEY
PAD
-
MACRO
PATTERN
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
1
EFF
2
NOR
REV
NOR
/REV
LIMIT
AUTOCUT
TRANS
KEY
PAD
-
CLR
CLR
EVENT
SEQ
EVENT
SEQ
MACRO
PATTERN
DISPLAY
DISPLAY
DVE
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
KEY1
KEY1
KEY2
KEY2
KEY3 KEY4
KEY4KEY3
1
KEY1 KEY2
KEY1 KEY2
KEY3 KEY4
KEY3 KEY4
1 2 3 4
5 6 7 8
KEY1 KEY2 KEY3 KEY4
2 3 4
5 6 7 8
CONTROL
SEQDSKFLXME3ME2ME1
CTRL
REV
NOR
/REV
LIMIT
KEY3
KEY4
KEY2
KEY1
CUT AUTO
DVE
FLX1 FLX4FLX3FLX2
DSK1 DSK2 DSK3 DSK4
FLX1 FLX2 FLX3 FLX4
DISPLAY
DSK1 DSK2 DSK3 DSK4
1 2 3 4
5 6 7 8
DISPLAY
EVENT
MACRO
SEQ
PATTERN
-
KEY
PAD
TRANS
CLR
DIGITAL VIDEO SWITCHER
TOP
KEY1 KEY2 KEY3 KEY4
Tap here if FORMAT is not displayed
in the Parameter Setting Area.
Parameter Setting Area
allows you to change
parameter settings.
Tap MU REBOOT
after setting.
SRC
SRC
DISP
INHI
HOLD
HOLD
SHIFT
LDVE
LDVE
SHIFT
2 3
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK CUT AUT O
EFF
EFF
2
1
LIMIT
NOR
/REV
MIX
WIPE
NOR
REV
DVE KEY1 KEY2 KEY4KEY3
1 2 3 4
5 6 7 8
DISPLAY
EVENT
MACRO
SEQ
PATTE RN
-
KEY
PAD
TRANS
CLR KEY1 KEY2 KEY3 KEY4
DVE
FLX1 FLX2 FLX3 FLX4
KEY5 KEY6 KEY7 KEY8
DISPLAY
FLX1 FLX2 FLX3 FLX4
KEY5 KEY6 KEY7 KEY8
PGM PST KEY1 KEY2 KEY3 KEY4
AUTO
Fader
M/E2 PST row
CUT
RATING LABEL 1
2
AC100-240V 50/60Hz IN
TO TOUCH PANEL UNITLINE4LINE3LINE2LINE1OPTIONAUX
GPI IN/TALLY OUT
DC OUTPUT (DC48V)
OUT 1 SERVICE
UNIT CONTROL
LAN 1 (MAIN)
OU Control Unit
HD/SD SDI (M/E2 PGM)
HD/SD SDI (M/E1 PGM)
75-ohm
termination
Reference
AC power source
AC1 0 0 - 24 0 V 50 /60 H z I N
PS1
PS2
AC1 00 - 2 4 0 V 5 0/6 0H z I N
CPU
I/O 1
I/O 2
I/O A
I/O B
A UX
2 3 4 1 2 3 4 5 6 7 8 9 10 11 121M/E
SDI OUTPUT
3 4 521
REF OUT
6
LAN1
(MAIN)
GPI IN TALLY OUT
RS-422
ARCNET LAN2
RE F IN GENLOCK
(SU B)
1 2 3 54 6 7 8 9 10 11 12
SDI IN PUT HDMI OUT1
SDI IN PUT HDMI OUT2
13 14 15 16 17 18 19 20 21 22 23 24
IN A IN B
IN C IN D
OPTION SLOT
SER. NO.
Preview
Video server,
etc.
HD/SD
SDI
HVS-2000
AC power source
F4F3F2F1
RESET USB2USB1
OU Touch Panel
https://www.for-a.com/
You can download manuals and other documents by registering your email address.
HVS-2000_OU-SETUPGUIDE-E-6.DOCX
5. Perform KEY Transitions
The following procedure example shows how
to display a logo using KEY1. Assume that
the fill and key signals are respectively input
IN11 and IN12.
(1) Press M/E2, then KEY/FLX in the touch
panel menu button block to display the
[FUNCTION > KEYER FLEXaKEY >
SRC/INS > M/E2] menu.
(2) Turn F1 to change TYPE to BUS.
(3) Turn F3 to select IN11.
(4) Turn F4 to select IN12.
(5) Press KEY1 ON AIR to cut in KEY1 into
the PGM image. (The KEY1 ON AIR button
lights up while KEY1 is displayed.)
(6) Press KEY1 AUTO to fade out KEY1 from
the PGM image.
6. AUX Output
Selecting AUX Output Video
(1) Press AUX1 in the top bus row. This allows you to select the AUX1 video signal in the top row.
(2) Signal names appear in the top button displays. To select Input 1, press the button just below the IN01 display.
(3) Press AUX2 in the bottom bus row. This allows you to select the AUX1 video signal in the upper row.
(4) Signal names appear in the bottom button displays. To select M/E1 program, press the button just below the
M/E1PGM.
If an AUX bus button is selected on the top row, select a signal on the top row. If an AUX bus button is selected on the
bottom row, select a signal on the bottom row. Thus, two AUX bus operation can be performed simultaneously.
Performing AUX1 Transitions
For example, to perform AUX1 transitions, AUX 1 transition must be enabled in the menu.
(1) Press AUX1 twice quickly to display the [SETUP > OUTPUT > OUT XPT] menu.
(2) Turn ENABLE to ON for AUX01.
(3) To change the AUX1 video to INPUT2 using fade in/out, press AUX1, MIX then IN02 (the bus button below “IN02” )
If you need to add effects to transitions, press WIPE instead of MIX.
7. Configuring the OU Component Units
LAN Connection
Use the supplied LAN cables to respectively connect the AUX BUS and LINE units to the Control Unit.
Power Connection
Use the supplied DC canon cables to connect the Control Unit and other units in a daisy chain. The last LINE Unit (LINE2 or 3) must be directly connected
to the Control Unit and the Touch Panel Unit must be the last device on the chain.
Do NOT plug or unplug power cords while the power is on.
* If using dedicated AC adapters, power can be directly supplied to the Touch Panel and a LINE Unit in Emergency mode (LINE 3). In such cases,
connect DC power cords to DC 12V IN terminals.
* LINE Unit 1, Unit 2 or Unit 3 is determined by the port to which the Unit has connected.
Precautions
- Operate the unit only at the specified supply voltage.
- Ensure the unit is properly grounded at all times.
- Ensure the power cord and connectors are firmly connected.
- Do not install/uninstall cards with power applied to the unit.
- Unit should not be operated or stored with the cover, panels, and/or casing
removed.
- Unit should not be operated or stored in a humid, dusty, etc.
environment. Doing so could result in fire or electrical shock.
- Do not allow fluids, metal fragments, or any other foreign objects to
enter the unit. If foreign matter does enter the unit, turn the power off
and disconnect the power cord immediately. Remove the material or
contact your authorized service representative.
- If you notice any strange smells or noises coming from the unit, turn
the power off immediately, disconnect the power cord, then contact
your authorized service representative.
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
FLX FLX FLX
FLX FLX
1 21 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18
16 17 18 1 2 3
FLX
3
FLX FLX
4
4DSK
DSK
DSK
DSK
DSK
DSK
DSK
DSK
1 2 3 4
1 2 3 4
MACRO
MACRO
MAC RO MACR O MAC RO MACR O
REC ATT ACH D ETAC H CHECK
DISP SHIFT SHIFT
2 3
INHI
CUT
CUT
MIX
MIX
WIPE
WIPE
USER
USER
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
FLX FLX FLX
FLX FLX
1 21 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18
16 17 18 1 2 3
FLX
3
FLX FLX
4
4DSK
DSK
DSK
DSK
DSK
DSK
DSK
DSK
1 2 3 4
1 2 3 4
MACRO
MACRO
MAC RO MACR O MAC RO MACR O
REC ATT ACH D ETAC H CHECK
DISP SHIFT SHIFT
2 3
INHI
CUT
CUT
MIX
MIX
WIPE
WIPE
USER
USER
CUT AUTO
EFF
EFF
2
1
LIMIT
NOR
/REV
MIX
WIPE
NOR
REV
DVE
PGM PST KEY1 KEY2 KEY3 KEY4 KEY1 KEY2 KEY4KEY3
DVE
FLX1 FLX4FLX3FLX2
DSK1 DSK2 DSK3 DSK4
FLX1 FLX2 FLX3 FLX4
DISPLAY
DSK1 DSK2 DSK3 DSK4
1 2 3 4
5 6 7 8
DISPLAY
EVENT
MACR O
SEQ
PATTERN
-
KEY
PAD
TRANS
CLR KEY1 KEY2 KEY3 KEY4
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX
FLX FLX FLX
FLX FLX
1 21 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18
16 17 18 1 2 3
FLX
3
FLX FLX
4
4DSK
DSK
DSK
DSK
DSK
DSK
DSK
DSK
1 2 3 4
1 2 3 4
MACRO
MACRO
MACRO
MACRO
MACRO MACRO MACRO MACRO
REC ATTACH DETACH CHECK
DISP SHIFT SHIFT
2 3
INHI
CUT
CUT
MIX
MIX
WIPE
WIPE
SRC HOLD LDVE SEL
SRC HOLD LDVE
SEL
SEL
DISP SHIFT
2SHIFT
3 BUS
INHI
HOLD
HOLD
LDVE
LDVE LOCK
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
EFF
2
1
NOR
REV
NOR
/REV
LIMIT
AUTOCUT
SRC
SRC
HOLD
HOLD
SHIFT
DISP 2SHIFT
3
LDVE
LDVE
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK
INHI
SRC
SRC
DISP
INHI
HOLD
HOLD
SHIFT
LDVE
LDVE
SHIFT
2 3
SEL
SEL
SEL
BUS
HOLD
HOLD
LDVE
LDVE LOCK CUT AUTO
EFF
EFF
2
1
LIMIT
NOR
/REV
MIX
WIPE
NOR
REV
TRNS
KEY
PAD
-
MACRO
PATTERN
PGM PST KEY1 KEY2 KEY3 KEY4
MIX
WIPE
EFF
1
EFF
2
NOR
REV
NOR
/REV
LIMIT
AUTOCUT
TRANS
KEY
PAD
-
CLR
CLR
EVENT
SEQ
EVENT
SEQ
MACRO
PATTERN
DISPLAY
DISPLAY
DVE
DVE
PGM PST KEY1 KEY2 KEY3 KEY4
KEY1
KEY1
KEY2
KEY2
KEY3 KEY4
KEY4KEY3
1
KEY1 KEY2
KEY1 KEY2
KEY3 KEY4
KEY3 KEY4
1 2 3 4
5 6 7 8
KEY1 KEY2 KEY3 KEY4
2 3 4
5 6 7 8
CONTROL
SEQDSKFLXME3ME2ME1
CTRL
REV
NOR
/REV
LIMIT
KEY3
KEY4
KEY2
KEY1
CUT AUTO
DVE
FLX1 FLX4FLX3FLX2
DSK1 DSK2 DSK3 DSK4
FLX1 FLX2 FLX3 FLX4
DISPLAY
DSK1 DSK2 DSK3 DSK4
1 2 3 4
5 6 7 8
DISPLAY
EVENT
MACRO
SEQ
PATTERN
-
KEY
PAD
TRANS
CLR
DIGITAL VIDEO SWITCHER
TOP
KEY1 KEY2 KEY3 KEY4
Set to BUS
Select IN11.
Select IN12.
RATING LABEL 1
2
AC100-240 V 50/60 Hz IN
TO TOUCH PANEL UNITL INE4LINE3L INE2LINE1OPTIONAUX
GPI IN/TALLY OUT
DC OUTPUT (DC48V)
OUT 1 SERVICE
UNIT CONTROL
LAN 1 (MAIN)
RATING LABEL
To MU LAN2 (SUB) port
LINE Unit (LINE 2)
LINE Unit (LINE 1)
LINE Unit (LINE 3)
Touch Panel Unit
Supplied DC power cord (Standard: 1 m)
Supplied LAN
cables
(Standard: 3 m)
(Standard: 10 m)
Supplied RS-422 cable (Standard: 10 m)
OU Control Unit
To MU LAN1 (MAIN) port
AUX BUS Unit
AC power source
Control
Control Unit Ethernet
DC 12 V IN
SERVICE / CTRL
-
1
-
2
-
3
-
4
