Premium Locking Floor Stand Kiosk
w/ Universal Security Enclosure, Keyboard Tray
and Storage Compartment (White)
PAD-PARAFWK
INSTRUCTION - MANUAL
CONTENTS:
INSTALLATION:
888-733-4448
1. Assembling Stand Body to Base :
A
x4
M4 x12
H
O
x1
M5 Allen Key
3. Assembling Enclosure to Stand : 4. Inserting Tablet into Enclosure :
1A. Allign the holes on the stand (A) with holes on the base (B) and turn in
screws (L) with provided allen tool (P) until securely tightened. Shown above.
2B. When the cable reaches the
bottom of the stand, pull through the
hole at the stand back and remove
the weighted pendant as shown.
2A. To route a charge cable through
the stand, attach the weighted
pendant to your charge cable, then
pass through the cutout at the top of
the stand.
3A. Align enclosure (C) VESA holes to VESA plate holes of stand (A) and from the
front of enclosure turn in screws (J) into the threaded VESA holes with provided
allen tool (O) until securely thigtened. Shown above.
4A. Find the appropiate size foam padding (M) for the tablet you wish to use.
Make sure device is compatible for the enclosure. if having power/data cord
attached to tablet, route it out the opening in the back.
**Tablet for illustration only,
NOT INCLUDED
C
x1
x1
F
M5 x12
x4
K
x4
M5 Nut
x1
DE
x1
M5 x 10
J
x4
M5 x 10
x4
B
x1
x4
M5 x12
Washer
G
x4
M4 x12
Washer
I
x1
N
P
x1
M6 Allen Key
L
x4
M
M6 x4
M6
2. Cable Routing :
M
M
C
C
A
O
A
B
L
P
J
8. Setting up Keyboard Tray to Floor Stand :
10. Mounting Magnetic Brochure Holder :
9. Expanding or Stowing Tray Extension
9A. If not extended, find the tray extension on the underneath of the main tray
body. Firmly adjust and fold out tray extension. Insert metal rod component into
hole as shown to securely lock extension piece in place. When stowing away,
you need to remove rod first, then fold up by rotating around the joint.
8A. Place keyboard tray (D) on the side holes of stand at desired height and turn in
Screws and washers(F,G or H,I) with the provided allen tool (O) until securely
tightened. Shown above.
11A. Enclosure can be oriented in vertical and horizontal positions as
needed. Shown above.
10A. Locate magnetic brochure
holder (O) and lay it on the
stand body (A) where needed.
**Tablet for illustration only,
NOT INCLUDED
**Tablet for illustration only,
NOT INCLUDED
**There are two versions
of the floor stand so both
set of hardware have been
included. One of the sets
will be left unused.
M
5. Optional - Placing Sheet Insert into Enclosure :
M
C
M
5B. Close and lock enclosure afterwards and you`re set
5A. Lay-in correct masking insert from bundle (M) as needed the correct
fitted look for your device.
888-733-4448
D
O
M5 x12
Screw
FG
M5 x12
Washer
OR
HI
M4 x12
Screw
M4 x12
Washer
6A. When installing device into enclosure (C), identify where the camera is.
Then simply remove and pop out the cover prior to mounting or setting up tablet
to properly expose camera.
**Tablet for illustration only,
NOT INCLUDED
**Tablet for illustration only,
NOT INCLUDED
C
6. Removing Back covers : 7. Setting up Security :
C
N
7A. Once the tablet device is set up,
close the front lid of the enclosure (A).
7B. Insert the key (N) in the keyhole on top
of enclosure, and turn clockwise to lock the
enclosure in place.
11. Portrait or Landscape :
snap**
OA
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
CTA ADD-PARAMULTI Owner's manual
-
-
-
-
-
CTA PAD-PARAMULTI Owner's manual
-
-
-
-
CTA PAD-PARAWPCL Owner's manual
Other documents
-
CTA Digital PAD-ASKB10 User manual
-
HoverCam Pilot X User manual
-
Hunter Fan Beck Owner's manual
-
Hunter Fan 59330 Owner's manual
-
MAHA Connect Series Operating instructions
-
Pure Fun 9315TS Installation guide
-
Pure Fun 9315TS Operating instructions
-
Hunter Fan 59625 Owner's manual
-
Hunter Fan 53430 Owner's manual
-
Hunter Fan 59651 Owner's manual
