Anchor Audio UHF-EXT500-H Owner's manual

Brand: Anchor Audio

Model: UHF-EXT500-H

Category: Microphones

Type: Owner's manual

This manual is also suitable for

OWNER’S MANUAL

UHF-EXT500

For service or repair, please call us at 1-800-262-4671 x782 or visit www.anchoraudio.com/technical-support-form.html

Our Technical Support team will help to troubleshoot. If unsuccessful and under warranty, they will issue you a Return Merchandise

Authorization (RMA) number. Once you ship your product back to Anchor Audio with the RMA number clearly noted on the box, we will diagnose

your unit and repair your unit then ship it back to you. All products must be shipped prepaid. C.O.D. shipments and shipments without an RA

number will be refused and returned at your expense. See page 18 for additional information.

IMPORTANT: Save the shipping box & packing materials. They were specially designed to ship your unit!

QUICK START GUIDE ......................................................................................................................................................................... 3

CONNECTING THE RECEIVER ............................................................................................................................................................. 7

SETTING UP CHANNEL ON RECEIVER ................................................................................................................................................. 8

SETTING UP THE HANDHELD MICROPHONE / BELT PACK TRANSMITTER .............................................................................................11

SYNCHRONIZING A TRANSMITTER WITH A RECEIVER ........................................................................................................................ 12

COLOR AND LABEL IDENTIFICATION ................................................................................................................................................13

BASIC CONNECTIONS ......................................................................................................................................................................14

TROUBLESHOOTING ........................................................................................................................................................................ 14

TECHNICAL SPECIFICATIONS ............................................................................................................................................................15

IMPORTANT SAFETY INSTRUCTIONS .................................................................................................................................................16

ANCHOR AUDIO WARRANTY / ANCHOR AUDIO RETURN AUTHORIZATION PROCEDURES .......................................................................18

CONTENTS

GETTING STARTED

Please check your new unit carefully for any damage which may have occurred during shipment. Each Anchor Audio product is carefully

inspected at the factory and packed in specially designed boxes for safe transport.

Notify the freight carrier immediately of any damage to the shipping box or product. Repack the unit in the original box and wait for inspection

by the carrier’s claim agent. Notify your Anchor Audio authorized dealer of the pending freight claim.

NOTE: All damage claims must be made with freight carrier!

RETURNING SYSTEMS FOR SERVICE OR REPAIR

MESSAGE FROM ANCHOR AUDIO

Congratulations on purchasing an Anchor Audio wireless system! You have joined the thousands of satisﬁed customers including the various

professional athletic teams, prestigious universities, school districts nationwide, ﬁrst responders, and the branches of the U.S. Military.

From developing our products on giant sticky notes to testing them in the parking lot and driving our neighbors crazy, our hearts - and ears -

are 110% committed to delivering reliable battery powered portable sound systems and portable PA systems for you. But we don’t stop there.

Anchor Audio is proudly manufactured in America and has plenty more solutions for you to choose from: speaker monitors, conference systems,

assistive listening, lecterns, and intercoms. We are your best friend in portable sound and are here for you when you need us...or even when

you don’t. We’re just a phone call away. With over 40 years of experience, our Engineering and Production to Sales and Tech Support teams will

provide you with the most reliable portable audio products and customer service.

Welcome to the Anchor Audio family! Feel free to contact us at any time. We’d love to hear from you.

Alex Jacobs

President

INTRODUCTION

FCC STATEMENT

SAFETY

ENVIRONMENT

UHF-EXT500

The PLL synthesized wireless microphone system operates in UHF 540 - 570 MHz frequency band with 700 selectable

channels. Please read this instruction manual carefully before operating the system. This manual covers the function and

operation of the wireless microphone system.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Notice: The changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is

permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and

void user’s authority to operate the device.

• Do not spill liquid on the appliance, and do not drop it on a hard concrete ﬂoor.

• Do not place the equipment near heat sources such as radiators, heating ducts, ampliﬁer, etc.

• Do not expose the equipment to direct sunlight, extreme dust, shock, or excessive moisture, rain, mechanical vibrations.

• If the unit has been not used for a long period of time, remove the battery from the transmitter as this will avoid potential

damage resulting from a defective leaking battery.

• If the equipment is not going to be used for a long period of time, disconnect the AC adapter from the power outlet. Please

note that if you turn the equipment off while leaving the AC adapter plugged in, it is not fully isolated from the power supply.

• WARNING: To reduce the risk of ﬁre or electric shock, do not use the products near water and do not expose them to rain or

moisture.

• Do not throw used batteries into ﬁre or garbage. Be sure to dispose of use batteries in accordance with local waste disposal

rules and regulations.

• When disposing of the equipment, remove the batteries, separate the case, circuit boards, and cables and dispose of all

components in accordance with local waste disposal rules.

Front Panel

Rear Back Panel

LCD Display

1. Antenna

2. Balanced XLR Audio Output

3. Unbalanced 1/4” Audio Output

4. Mic/Line Switch: Use this to adjust audio output level for mic level (-20 dB)

or line level (0 dB)

5. Squelch: turn the knob to adjust or decrease the noise ﬂoor level

6. Power Adapter Connector

1. MANUAL: Use this mode to select free channel manually

2. SCAN: Use this mode to set free channel by auto-scan function

3. PRESET: Use this mode to set multiple constructions by preset group

4. SYNC: The synchronization process is actuated

5. GP: Display selected preset group

6. CH: Display selected preset channel

7. CH: Display selected channel number

8. FREQ: Display selected frequency

9. MUTE: Audio output is muted

10. RF Bar: Display the reception status of RF signal

11. AF Bar: Display the reception status of AF signal

1 1

2 3 4 5 6

5 6

9 10 11

3 4 6

1. Power Button

2. LCD Display: Display channel, frequency and settings

3. Button : Tap the channel forward/backward

4. SYNC Button: Press the button to actuate the synchronization with the

transmitter

5. SET Button: Press button to activate the manual or auto-scan or preset mode

6. Volume Controller: Adjust the receiver output level

BASIC SYSTEM OPERATION - WR-EXT500

7 5

4 3 6 1

1. Power Button: Press for 2 seconds to power the microphone on or off

2. Power LED: Indicates the power/low battery level status.

1. Power Button: Press for 2 seconds to power the belt pack on or off.

2. Mute Button: With the transmitter on, a slight press of button will toggle between mute

and unmute function.

3. Power LED: Indicates the power/low battery level status.

4. MUTE LED: Blue LED light on means unit is in mute status.

5. SYNC Button: Press to actuate the synchronization process with the receiver.

6. LCD Display: Display channel number and battery power level.

7. Battery Compartment: Insert two AA dry or rechargeable batteries into the

compartment and make sure that the polarity of batteries is correct.

8. Mini XLR Connector: Connect to the lapel microphone or headset microphone.

9. Gain Switch: The switch sets the audio input to -20dB, -10dB, or 0dB.

3. Talk Button: Push the button up to talk.

4. SYNC Button: Press to actuate the synchronization process with the receiver

5. LCD Display: Display channel number and battery power level.

6. Battery Compartment: Insert two AA dry or rechargeable batteries into the compartment and make sure that the polarity of

the batteries is correct.

7. Grille: Protects the microphone capsule and helps reduce breath sounds and wind noise.

LED Indicator Status

Green Ready

Flashing Green The synchronization process is actuated

Flashing Red Low battery power with less than 10 minutes of operation left

LED Indicator Status

Green Ready

Flashing Green The synchronization process is actuated

Flashing Red Low battery power with less than 10 minutes of operation left

BASIC SYSTEM OPERATION - WH-EXT500

BASIC SYSTEM OPERATION - WB-EXT500

SETTING UP THE HANDHELD MICROPHONE / BELT PACK TRANSMITTER

Open the battery cover and insert batteries into the

battery compartment conforming to the polarity +/-

marks.

Unscrew the handheld Mic and open the battery cover

to insert the battery into the battery compartment and

conﬁrm the marks of the polarity +/-.

Press for 4 seconds to turn the Handheld/Belt pack

transmitter on.

If the LED stays ﬂashing. It indicates that the battery will

be out of power soon and should be replaced.

Adjust the audio input level.

-0dB (default setting)

-10dB

-20dB

NOTE: When you aren’t using the handheld mic/belt pack for a long period of time, move the power

switch to Off mode to save battery life.

SECONDS

Manual Mode

Notice: Do not put two or more transmitters operating nearby when setting up the frequency channel. Please keep

transmitter at least one meter away from receiver.

Setting up interference-free channel by manual operation

Using the button to select the “MANUAL” mode.

Press “SET” button for 2 seconds till LCD display

is ﬂashing.

Press button to change the channel forward.

Press “SET” button to lock the setting.

SETTING UP CHANNEL ON RECEIVER

Preset Mode

Set multiple channels by using preset channels. There are 4 preset groups. Excluding the interference from external, there are 8

preprogrammed channels that can be operated simultaneously in each group.

NOTE: When there is any interference on the current preset group, switch to the next preset group. If all 4 preset groups have interference,

use the auto-scan mode or manual mode to set up the system.

Use the button to select the “PRESET” mode.

Press the channel button to change the

programmable group forward.

Press the channel button to change the

programmable channel forward.

Press “SET” button for 2 seconds till LCD display is

ﬂashing.

Press “SET” button to lock group setting.

Press “SET” button to lock the channel setting.

Auto-Scan Mode

Using the button to select the “SCAN” mode.

Press “SET” button for 2 seconds till LCD display

is ﬂashing.

Press button to scan in forward direction, and it will

stop at the free-interference channel automatically.

Press the “SET” button to lock the setting.

Set interference-free channel by automatic frequency function.

Insert Batteries

SYNC

Step 1

Step 2

SECONDS

MUST BE LESS THAN 1 METER

AWAY FROM Belt pack OR

HANDHELD MICROPHONE

PRESS AND HOLD SYNC

SYNC

Prior to setting up, please check that the transmitter and receiver are tuned to the same frequency or channel. Two or more transmitters

operating in the same frequency can not be used at the same time and same area.

Connect the provided DC power supply to the receiver with an appropriate AC

power source. The receiver is on when the LCD screen display lights up.

Using a standard audio cable with 3-pin XLR connectors or 1/4” phono cable to

connect the mixer or ampliﬁer

Never use the balanced and unbalanced audio outputs at the same time. This may

cause signal loss or increased noise

Set the audio output level for

MIC: -20dB

LINE: 0dB (Default setting)

Using the Volume Knob to adjust the AF audio level to the input of the

ampliﬁer or mixer.

Use the SQ (squelch) to avoid reproducing noise when the receiver does not receive

enough signal from the transmitter.

Turn clockwise to increase squelch and reduce noise. When turning the squelch

knob clockwise, it begins to eliminate background noise.

When squelch is all the way to the left, the squelch is off and the ambient RF noise

will be easily heard.

Default settings: In minimum SQ position.

Minimum SQ

Maximum SQ

Default settings: In minimum VOLUME position.

Balanced XLR Cable

Unbalanced 1/4” Phono Cable

VOLUME

SYSTEM OPERATION

QUICK START GUIDE

1. Connect Receiver to Power Cable then plug into a Grounded Power Outlet

2. Connect Mixer or Ampliﬁer

Balanced XLR Cable Unbalanced 1/4” Phono Cable

3. Scan Free Channel

SET

SECONDS

SYNCHRONIZING A TRANSMITTER WITH A RECEIVER

Automatic frequency synchronization via remote channel for easy setup

1. First, switch the transmitter and the receiver on. Press and hold

the SYNC button on your transmitter. The SYNC ﬂashes on the

receiver display panel.

Press the SYNC button on the receiver front panel, the transmitter

will set the same channel as receiver automatically.

2. When using SYNC setting, the distance of receiver and transmitter

should be within 1 meter.

Step 1

USE BELT PACK OR HANDHELD MICROPHONE

Step 2

PRESS AND HOLD SYNC

SYNC

MUST BE LESS THAN 1 METER

AWAY FROM BELT PACK OR

HANDHELD MICROPHONE

COLOR AND LABEL IDENTIFICATION

You can also stick the color label on the receiver and transmitter for

quickly identifying the paired system.

MOUNTING THE RECEIVER

To combine two receivers in 19” standard rack, use the two short L type metal racks and two metal connecting plates, included

in the UHF-EXT500 box.

TROUBLESHOOTING

UHF-EXT500

Problem Solution

No Sound

• Check the power supply of the microphone and receiver

• Check that the transmitter and receiver are tuned to the same frequency

• Check whether the hI-ﬁ appliance is switched on and the receiver output is connected to audio mixer or

ampliﬁer input

• Check whether transmitter is too far away from receiver or SQUELCH control set too high

• Check whether receiver is located too near metal object or there are obstructions between transmitter

and receiver

Sound Interference

• Check the antenna location

• When using 2 or above microphone sets simultaneously, make sure that the chosen frequencies are not

interfered

• Check whether the interference comes from other wireless microphones, TV, radio and etc.

Distortion

• Check the receiver volume level whether is set too high or too low

• Check whether the interference comes from other wireless microphones, TV, radio and etc.

TECHNICAL SPECIFICATIONS

UHF-EXT500

Receiver

Frequency Range UHF 540 ~ 570 MHz (Regionally Selected)

Case Half 19” EIA Rack Metal Case

Oscillator PLL Synthesized

Modulation FM

S/N Radio > 100 dB at 200 KHz deviation and 60 dBµV antenna input

Image & Spurious Rejection 70 dB minimum

Receiving Sensitivity At 2µV over 52 dB S/N ratio

AF Response 80 Hz to 18 KHz

T.H.D. <1% (at 1 KHz)

IF Frequency 1st: 243.95 MHz 2nd: 10.7 MHz

Dynamic Range >100 dB

Tone Signal 32.768 KHz

Audio Output Balanced & Unbalanced

Power Supply DC 12V

Current Consumption 260 ± 10 mA

Dimensions and Weight

Total (HWD) 1.65” x 7.9” x 7.2” (4.2 x 20 x 18.3 cm)

Weight 2.05 lbs / 0.93 Kg

Handheld / Belt Pack Transmitter

Frequency Range UHF 540 ~ 570 MHz (Regionally Selected)

Channel Select SYNC with Receiver

Display LCD displays status, channel, or battery

RF Power Output 10 mW (max.)

Frequency Stability ± 0.005%

Spurious Emission >60 dB below carrier frequency

Gain Setting Belt Pack: 0 dB, -10 dB, -20 dB (3 settings)

Mic Unit Handheld: Uni-Direction dynamic unit or

Uni-Direction electret condenser unit

Belt Pack: Lavalier Mic / Headset Mic

Battery 1. DC2.4V (1.2V x 2 AA size rechargeable batteries)

2. DC3V (1.5V x 2 AA size batteries)

Current Consumption 120 ± 10 mA

Dimensions and Weight

Total (HW) Handheld: 10.2” x 2.1” (26 x 5.4 cm)

Total (HWD) Belt Pack: 3.8” x 2.5” x .95” (9.7 x 6.5 x 2.4 cm)

Weight Handheld: 0.52 lbs /0.234 Kg

Weight Belt Pack: 0.19 lbs /0.086 Kg

IMPORTANT SAFETY INSTRUCTIONS

General Warning or Caution

Electric Shock

Protective Conductor Terminal

European Union CE Mark

Alternating Voltage Symbol

Waste Electrical and Electronic Equipment (WEEE)

Electrical Requirements

Inspection for Damage

Fuses

On Symbol

Off Symbol

The Exclamation Symbol in the ﬁgure to the left appears in Warning and

Caution tables throughout this document. This symbol designates an

area where personal injury or damage to the equipment is possible.

The Electrical Shock Symbol in the ﬁgure to the left appears throughout

this manual. This symbol indicates a hazard arising from dangerous

voltage. Any mishandling could result in irreparable damage to the

equipment and personal injury or death.

The Electrical Shock Symbol in the ﬁgure to the left appears throughout

this manual. This symbol indicates a hazard arising from dangerous

voltage. Any mishandling could result in irreparable damage to the

equipment and personal injury or death.

The presence of the CE Mark on Anchor Audio equipment means that it

has been designed, tested, and certiﬁed as complying with all applicable

European Union (CE) regulations and recommendations.

The alternating voltage symbol means that the unit can also be used with

AC (alternating current) that is in the form of electric power from a wall

socket.

This symbol on the product or on its packaging indicates that this product

must not be disposed of with regular waste. Instead, it is the user’s

responsibility to dispose of waste equipment according to the local laws.

The separate collection and recycling of the waste equipment at the time

of disposal will help to conserve natural resources and ensure that it is

recycled in a manner that protects human health and the environment. For

information about where the user can drop off the waste equipment for

recycling, please contact your local authority for recycling advice.

Warning: To reduce the risk of ﬁre or electric shock, do not expose this

apparatus to rain or moisture, apparatus shall not be exposed to dripping or

splashing and no objects ﬁlled with liquids, such as vases or cups, shall be

placed on the apparatus.

The apparatus should be connected to a main socket outlet with a protective

earthing connection. For Nordic markings refer to copy of marking label.

The plug in the power cord is the AC mains disconnected device and must

remain readily operable.

There should be a minimum distance around the apparatus for sufﬁcient

ventilation. The ventilation should not be impeded by covering the ventilation

openings with items, such as newspapers, table-cloths, curtains, etc.; no naked

ﬂame sources, such as lighted candles, should be placed on the apparatus.

Equipment may be located above or below this apparatus, but some equipment

(like large ampliﬁers) may cause an unacceptable amount of hum or may

generate too much heat and degrade the performance of this apparatus.

Before attempting to power up the unit for the ﬁrst time, the following

precautions must be followed:

Anchor Audio products are carefully packaged at the factory to minimize the

possibility of damage during shipping. Inspect the box for external signs of

damage or mishandling. Inspect the contents for damage. If there is visible

damage to the instrument upon receipt, inform the shipping company and

Anchor Audio immediately.

Have a qualiﬁed electrician verify the wall socket that will be used is properly

polarized and properly grounded.

The fuse symbol in the ﬁgure to the left identiﬁes the fuse location on the

Anchor Audio product. (Not required if not user replaceable)

The On Symbol in the ﬁgure to the left represents a power switch position

on the Anchor Audio product. This symbol represents a Power On condition.

The Off Symbol in the ﬁgure to the left represents a power switch position

on the Anchor Audio product. This symbol represents a Power Off condition.

WARNING

To avoid electric shock, connect the instrument to properly

earth-grounded, 3-prong receptacles only. Failure to

observe this precaution can result in severe injury.

Inspection for Damage

Do not attempt to operate this equipment if there is evidence of

shipping damage or you suspect the unit is damaged. Damaged

equipment may present additional hazards to you. Contact

Anchor Audio Technical Support for advice before attempting to

plug in and operate damaged equipment.

Anchor Audio Technical Support:

800.262.4671 x782

Direct Current Symbol

This international symbol implies a direct voltage or current.

Figure DC Voltage Symbol

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

IMPORTANT SAFETY INSTRUCTIONS (CONT’D)

1) Read Instructions – All the safety and operation instructions should be read before the

product is operated.

2) Retain Instructions – The safety and operating instructions should be retained for future

reference.

3) Heed Warnings – All warnings on the product and in the operating instructions should be

adhered to.

4) Follow Instructions – All operating and use instructions should be followed.

5) Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Exception: A product that is meant for uninterrupted service and that for some speciﬁc

reason, such as the possibility of the loss of an authorization code for the CATV

converter, is not intended to be unplugged by the user for cleaning or any other purpose,

may exclude the reference to unplugging the product in the cleaning description

otherwise).

6) Attachments – Do not use attachments not recommended by the product manufacturer

as they may cause hazards.

7) Water and Moisture – Do not use this product near water – for example, near a bath tub,

wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool;

and the like.

8) Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or

table. The product may fall, causing serious injury to a child or adult and serious damage

to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the

manufacturer or sold with the product. Any mounting of the product should follow the

manufacturer’s instructions and should use a mounting accessory recommended by the

manufacturer.

9) A product and cart combination should be moved with care. Quick stop, excessive force,

and uneven surfaces may cause the product and stand combination to overturn.

10) Ventilation – Slots and openings in the cabinet are provided for ventilation to ensure

reliable operation of the product and to protect it from overheating. These openings must

not be blocked or covered. The openings should never be blocked by placing the product

on a bed, sofa, rug, or other similar surface. This product should not be placed in a

build-in installation such as a bookcase or rack unless proper ventilation is provided, or

the manufacturer’s instructions have been adhered to.

11) Power Sources – This product should be operated only from the type of power source

indicated on the marking label. If you are not sure of the type of power supply to your

home, consult your product dealer or local power company. For products intended to

operate from battery power or other sources refer to the operating instructions.

12) Grounding or Polarization – This product may be equipped with a polarized alternating-

current line plug (a plug having one blade wider than the other). This plug will ﬁt into

the power outlet only one way. This is a safety feature. If you are unable to insert the

plug fully into the outlet, try reversing the plug. If the plug should still fail to ﬁt, contact

your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the

polarized plug.

13) Power-Cord Protection – Power-supply cords should be routed so that they are not likely

to be walked on or pinched by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the point where they exit from

the product.

14) Protective Attachment Plug – The product is equipped with an attachment plug having

overload protection. This is a safety feature. If replacement of the plug is required, be

sure the service technician has used a replacement plug speciﬁed by the manufacturer

that has the same overload protection as the original plug.

15) Outdoor Antenna Grounding – If an outside antenna or cable system is connected to

the product, be sure the antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges. Article 810 of the National

Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of

the mast and supporting structure grounding of the lead in wire to an antenna discharge

unit, size of grounding conductors, location of antenna-discharge unit, connection of

grounding electrodes, and requirements for the grounding electrode. See Figure A.

16) Lightning – For added protection, unplug this product during a lightning storm, or when it

is left unattended and unused for long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent damage to the product due to

lightning and power-line surges.

17) Power Lines – An outside antenna system should not be located in the vicinity of

overhead power lines or other electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside antenna system, extreme care

should be taken to keep from touching such power lines or circuits as contact with them

might be fatal.

18) Overloading – Do not overload wall outlets, extension cords, or integral convenience

receptacles as this can result in a risk of ﬁre or electric shock.

19) Object and Liquid Entry – Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or short-out parts that could result

in a ﬁre or electric shock. Never spill liquid of any kind on the product.

20) Servicing – Do not attempt to service this product yourself as opening or removing

covers may expose you to dangerous voltage, other hazards, and potentially void the

warranty. Refer all servicing to qualiﬁed service personnel.

21) Damage Requiring Service – Unplug this product from the wall outlet and refer servicing

to qualiﬁed service personnel under the following conditions:

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled or objects have fallen into the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions as an

improper adjustment of other controls may result in damage and will often require

extensive work by a qualiﬁed technician to restore the product to

its normal operation.

e. If the product has been dropped or damaged in any way.

f. When the product exhibits a distinct change in performance – this indicates a

need for service.

22) Replacement Parts – When replacement parts are required, be sure the service

technician has used replacement parts speciﬁed by the manufacturer or have the same

characteristics as the original part. Unauthorized substitutions may result in ﬁre, electric

shock, or other hazards.

23) Safety Check – Upon completion of any service or repairs to this product, ask the service

technician to perform safety checks to determine that the product is in proper operating

condition.

24) Wall or Ceiling Mounting – The product should be mounted to a wall or ceiling only as

recommended by the manufacturer.

25) Heat – The product should be situated away from heat sources such as radiators, heat

registers, stoves, or other products (including ampliﬁers) that produce heat.

26) Warning: Battery pack or batteries installed shall not be exposed to excessive heat such

as sunshine, ﬁre, or the like.

Technical Support Team

800.262.4671 x782

[email protected]

Sales Team

800.262.4671 x772

[email protected]om

Technical Support Team

800.262.4671 x782

[email protected]

Sales Team

800.262.4671 x772

[email protected]om

5931 Darwin Court | Carlsbad, CA 92008 USA | anchoraudio.com

ANCHOR AUDIO WARRANTY

Anchor Audio products are warranted to be free from defects in materials and workmanship for the period of SIX (6) YEARS from the date of original

purchase unless listed below.

Warranted for a period of TWO (2) YEARS:

• All wired and wireless microphones, belt pack transmitters, base station transmitters, base station receivers, and hands-free

microphones

• All woodworking

• CouncilMAN microphones and bases

• PortaCom and ProLink 500 systems in their entirety

• Assistive Listening systems in their entirety

• Accessories, cables, cases, and covers

NOTE: The ‘AA’ batteries are not covered under warranty by Anchor Audio.

Warranties are subject to the following conditions:

• Product must have been purchased from an authorized Anchor Audio Dealer and have an Anchor Audio serial number

• Anchor Audio must perform or authorize all warranty services or warranty is void

• Warranty is void when equipment is subjected to negligent use, connected to improper power sources, misuse, and/or operation

beyond speciﬁcations and limits

• Warranty shall not apply to exterior ﬁnish, AC power cords, bulbs, or any other failings due to normal wear

• Warranty is void when equipment is subjected to adverse temperature, humidity, moisture, or any condition not considered normal

environmental conditions

• Products out of warranty cannot be repaired by Anchor Audio

• In all cases, dealers and end users must ﬁrst obtain approval from Anchor Audio for any product they are attempting to return to Anchor Audio.

Upon approval, a Return Merchandise Authorization (RMA) number will be issued by the Anchor Audio Customer Service Department and must

accompany all products returned. Clearly note the RMA number on the outside of the box.

• Products returned without approval and an RMA number may be returned to the sender.

• The RMA expires 30 days from date of issue. Any product received after 30 days of the RMA issue date will be returned to sender.

• Products returned must include a RMA number. Product received without an RMA number visibly seen on the box will incur a $25 processing fee.

• Customer will incur the cost of shipping product to Anchor Audio for any reason. Under warranty repair and/or replacement, Anchor Audio will

incur the freight cost to return product to the dealer or customer within the continental U.S.A.

ANCHOR AUDIO RETURN AUTHORIZATION PROCEDURES

Last Updated: August 7, 2019

Anchor Audio UHF-EXT500-H Owner's manual

Brand: Anchor Audio

Model: UHF-EXT500-H

Category: Microphones

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Anchor Audio UHF-EXT500-H Owner's manual

This manual is also suitable for

Anchor Audio UHF-EXT500-H Owner's manual

Related papers

Other documents