Tyan S5197 User manual

1

http://www.tyan.com

Toledo i3010W

///

S5197

Version 1.00

Copyright

manual may be reproduced or translated without prior written consent from TYAN

Computer Corp.

Trademark

All registered and unregistered trademarks and company names contained in this

manual are property of their respective owners including, but not limited to the

following.

TYAN, Toledo i3010W are trademarks of TYAN Computer Corporation.

Intel, Prescott, and combinations thereof are trademarks of Intel Corporation.

Phoenix, Phoenix-Award BIOS are trademarks of Phoenix Technologies.

Microsoft, Windows are trademarks of Microsoft Corporation.

SuSE, is a trademark of Novell.

IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.

Notice

Information contained in this document is furnished by TYAN Computer Corporation

and has been reviewed for accuracy and reliability prior to printing. TYAN assumes

no liability whatsoever, and disclaims any express or implied warranty, relating to

sale and/or use of TYAN products including liability or warranties relating to fitness

for a particular purpose or merchantability. TYAN retains the right to make changes

to product descriptions and/or specifications at any time, without notice. In no event

will TYAN be held liable for any direct or indirect, incidental or consequential

damage, loss of use, loss of data or other malady resulting from errors or

inaccuracies of information contained in this document.

2

http://www.tyan.com

Table of Contents

Check the box contents! 3

Chapter 1: Introduction

1.1 Congratulations 5

1.2 Hardware Specifications 5

1.3 Software Specifications 7

Chapter 2: Board Installation

2.1 Board Image 9

2.2 Block Diagram 10

2.3 Board Parts, Jumpers and Connectors 11

2.4 Jumper Settings 12

2.5 Tips on Installing Motherboard in Chassis 21

2.6 Installing the Memory 23

2.7 Installing the Processor & Cooling Fan 25

2.8 Attaching Drive Cables 28

2.9 Installing Add-in Cards 30

2.10 Connecting External Devices 31

2.11 Installing the Power Supply 32

2.12 Finishing Up 33

Chapter 3: BIOS Setup

3.1 About the BIOS 34

3.2 BIOS Main Setup 36

3.3 Main Menu 37

3.4 Advanced Menu 43

3.5 Security Menu 55

3.6 Power Menu 56

3.7 Boot Menu 57

3.8 Exit Menu 58

Chapter 4: Diagnostics

4.1 Beep Codes 59

4.2 Flash Utility 59

4.3 Phoenix BIOS Post Code 60

Appendix I: SMDC Information

64

Appendix II: How to Make a Driver Diskette

67

Glossary

69

Technical Support

77

3

http://www.tyan.com

Check the box contents!

1x S5197 motherboard

1x 34-Pin floppy drive cable

1 x Ultra-DMA-133/100/66/33 IDE cable

2 x Serial ATA power cable

4 x Serial ATA cable

1 x S5197 user’s manual

1 x S5197 Quick Reference guide

1 x TYAN driver CD

1 x I/O shield

If any of these items are missing, please contact your vendor/dealer for

replacement before continuing with the installation process.

NOTE: The box contents do not include any driver diskette. Please use the

included driver CD to make a driver diskette. Refer to Appendix II for the

information on how to make a driver diskette.

4

http://www.tyan.com

NOTE

5

http://www.tyan.com

Chapter 1: Introduction

1.1 - Congratulations

You have purchased one of the most powerful server solutions. The Toledo

i3010W (S5197) is a flexible Intel

®

platform for multiple applications, based on Intel

®

Mukilteo-2P MCH and ICH7-R chipsets.

Designed to support the family of Intel

®

Socket 775 processors and 8GB DDR2

533/667 memory, the S5197 has integrated Dual Gigabit Ethernet LAN, built-in

32MB ATI graphics controller and four SATA-II ports. This motherboard represents

the best choice for a server platform product.

Remember to visit TYAN’s Website at http://www.TYAN.com

. There you can find

information on all of TYAN’s products with FAQs, online manuals and BIOS

upgrades.

1.2 - Hardware Specifications

Processors

z Intel

®

Pentium 4 1066/800/533

MHz FSB

z Supports Intel® Celeron®D ,

Pentium® D, Pentium® 4,

Pentium® Extreme Edition,

Intel® Core™2 Duo processor

z Single Socket-T LGA775 socket

Expansion Slots

z Two PCI-X 133/100/66 slots in

one PCI-X bus

z One PCI-Express x16 slot with

PCI-Express x8 signals

z PCI-Express x4 slot with PCI-

Express x4 signals

z One 32bit/33MHz 3.3V PCI 2.2

slot

z Total five usable slots

Chipset

z NB: 3010 Mukilteo-2P MCH,

IOB: 6702 PXH-V; SB: ICH7R

z SMSC SCH5027 Super I/O chip

w/PECI support

System Management

z Supports Tyan M3291 SMDC

via 25x2 pin-header

z Integrated H/W Monitoring

functions in Super I/O chip with

PECI support

z One 4-pin CPU fan header and

four 4-pin system fan headers

z 2-pin chassis intrusion header

z Temperature and voltage

monitoring

Intelligent Platform Management

Interface Header

z Tyan M3291 Server

Management Daughter card

(Optional) supports features

listed below via IPMI header

z Based Renesas H8 2167

Baseboard Management

Controller (BMC)

z Tailored for IPMI 2.0

specifications

z Windows and Linux based

Management Solution

z Supports RMCP and SNMP

protocols

6

http://www.tyan.com

Memory

z Dual or single DDR-II memory

channels

z Four DDR-II 533/667 DIMM

sockets

z Supports up to 8 GB ECC or

non-ECC unbuffered memory

Integrated I/O

z One floppy connector for up to

two drives

z One IDE connector

z One COM port (via cable)

z One ECP/EPP/SPP parallel port

header (via an optional cable)

z Four USB v2.0 in USB Type A

(vertical) connectors

z Four SATAII ports

z One 2x25 connector for optional

TYAN SMDC card

Integrated PCI IDE

z Single ATA100/66 IDE bus

master channel supports up to 2

ATA/ATAPI IDE compliant drives

Integrated SATA Controller

(ICH7-R)*

z Supports 4 SATAII ports running

at 3.0Gb/s

z Support Raid 0/1/5/10

(*Note: the current version of the

ICH7R SATA RAID Utility can only

support Windows XP/2000/2003)

Onboard Graphics

z ATI ES1000 (a.k.a. RN50) VGA

graphics controller

z 32MB frame buffer

z I

2

C serial multi-master

controllers and UARTs

z Remote power on/off and reset

support (IPMI-over-LAN) on

Intel’s 82573

BIOS

z Phoenix BIOS 8Mb flash ROM

z Supports ACPI 1.0, PnP

z Auto detection of memory size

z Auto configuration of IDE hard

disk types

z User settings of hardware

monitoring

z Multiple boot options including

PXE or emulated FD/HD

z Power Management: S1, S3, S4

and S5

Back Panel I/O Ports

z One stacked Mouse/ Keyboard

connector

z One stacked four-port USB

connector

z One 9-pin COM Port

z One 15-pin VGA Port

z Two side-by-side GbE RJ45

Form Factor

z Standard ATX (12" x 9.6”)

z EPS/12V 24-pin plus 8-pin

power connectors

Power

z Onboard 5-phase CPU VRM

z One universal 24-pin EPS/12V

system power connector plus

one 8-pin power connector for

processor power

7

http://www.tyan.com

Integrated LAN Controller(s)

z Two 10/100/1000 Gigabit

Ethernet NIC

z Two Intel’s 82573 GbE NICs

(1*82573E & 1*82573V)

z Running at independent x1 PCI-

Express bus

Regulatory

z FCC Class B (Declaration of

Conformity)

z European Community CE

(Declaration of Conformity)

1.3 - Software Specifications

OS (Operating System) Support

Windows Server 2003 (R2 or later)

Red Hat Linux EL4

Red Hat Linux EL5

SuSE Enterprise Server 10

TYAN reserves the right to add support or discontinue support for any OS

with or without notice.

8

http://www.tyan.com

Chapter 2: Board Installation

You are now ready to install your motherboard. The mounting hole pattern of the

Toledo i3010W S5197 matches the ATX specification. Before continuing with

installation, confirm that your chassis supports an ATX motherboard.

How to install our products right… the first time

The first thing you should do is reading this user’s manual. It contains important

information that will make configuration and setup much easier. Here are some

precautions you should take when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the

antistatic bag. Unplug the power from your computer power supply and

then touch a safely grounded object to release static charge (i.e. power

supply case). For the safest conditions, TYAN recommends wearing a

static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the

board, or flex the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors,

memory modules, and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic

bag that the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your

chassis, as well as installing the processor, memory, disk drives and cables.

NOTE

DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN

DAMAGED

9

http://www.tyan.com

2.1- Board Image

This picture is representative of the latest board revision available at the

time of publishing. The board you receive may or may not look exactly

like the picture above.

10

http://www.tyan.com

2.2 - Block Diagram

Toledo i3010W S5197

11

http://www.tyan.com

2.3 - Board Parts, Jumpers and Connectors

This diagram is representative of the latest board revision available at the time of

publishing. The board you receive may not look exactly like the diagram above.

12

http://www.tyan.com

2.4 – Jumper Settings

Jumper Function Settings

J3 COM1 Connector See Section 2.4.1

J5 COM2 Connector See Section 2.4.2

J6

External Speaker Header and Enable/Disable

Buzzer

See Section 2.4.3

J8 LPT Connector See Section 2.4.4

J30，J31

J43，J44

USB Header (4-Pin x 1) See Section 2.4.5

J37 Front Panel Header See Section 2.4.6

J32~J35

Front Panel LAN1/LAN2 Link and Active LED

Connector: J32 ~ J35

See Section 2.4.7

J40 ASF 2.0/SMDC Select See Section 2.4.8

JP1 Clear CMOS Jumper See Section 2.4.9

JP2，JP3 LAN1&LAN2 Enable/Disable Jumper See Section 2.4.10

JP24 PCI-X Frequency Configure See Section 2.4.11

FAN1~5 FAN Headers See Section 2.4.12

Jumper Legend

OPEN - Jumper OFF Without jumper cover

CLOSED - Jumper ON With jumper cover

To indicate the location of pin-1

13

http://www.tyan.com

2.4.1 – COM1 Connector (J3)

Signal

Description

#

Signal

Description

DCD

1 2

DSR

RXD

3 4

RTS

TXD

5 6

CTS

DTR

7 8

RI

GND

9 10

KEY

2.4.2 – COM2 Connector (J5)

Signal

Description

#

Signal

Description

DCD2

1 2

DSR2

RXD2

3 4

RTS2

TXD2

5 6

CTS2

DTR2

7 8

RI2

GND

9 10

KEY

14

http://www.tyan.com

2.4.3 –External Speaker Header and Enable/Disable Buzzer (J6)

Enable onboard buzzer

Disable onboard buzzer

Pin 1 and Pin 4 for an

external speaker header

Pin 1: +5Vdc power

Pin 4: SPK_DATA

2.4.4 – LPT Connector (J8)

Signal

Configuration

#

Signal

Configuration

STB# 1 2 AFD#

LPD0 3 4 ERR#

LPD1 5 6 INIT#

LPD2 7 8 SLIN#

LPD3 9 10 GND

LPD4 11 12 GND

LPD5 13 14 GND

LPD6 15 16 GND

LPD7 17 18 GND

ACK# 19 20 GND

BUSY 21 22 GND

PE 23 24 GND

SLCT 25 26 KEY

15

http://www.tyan.com

2.4.5 –Vertical USB Header (4-Pin x 1) (J30, J31, J43, J44)

Pin_4: GND

Pin_3 : DATA +

Pin_2 : DATA -

Pin_1

Pin_1 : +5VPWR

2.4.6 – Front Panel Header (J37)

Signal

#

Signal

HD_

LED+

1 2

PW_

LED+

HD_

LED-

3 4

PW_ LED-

GND0

5 6

PWR_

S/W#

RESET

7 8

GND2

GND1

9 10

SLP_SW#/

WLED+

Ext.

Interrupt

11 12

GND3/

WLED-

+5VSB

13 14

NC

SMBUS

Data

15 16

GND4

The Front Panel Header is used to connect some control

or signal wires from motherboard to chassis, such as

HDD LED, power LED, power button, and reset button.

SMBUS

Clock

17 18

INTRU#

16

http://www.tyan.com

2.4.7 – Front Panel LAN1/LAN2 Link and Active LED Connector: J32 ~ J35

J35

1

J32

1

J35 is for connecting an

external LED to indicate LAN2

LINK and ACTIVITY. The

behavior of this LED is the

same as LAN2 RJ45 LED2:

Pin 1: LED+

Pin 2: LED-

J32 is for connecting an

external LED to indicate LAN1

LINK and ACTIVITY. The

behavior of this LED is the

same as LAN1 RJ45 LED2:

Pin 1: LED+

Pin 2: LED-

The external LED’s for J32 and J34

can be either bi-color or single-color

LED.

For a single-color LED to indicate

1000Mbps SPEED, connect Pin 1 to

LED+ and Pin 2 to LED-.

J34

1

J33

1

J34 is for connecting an

external LED to indicate LAN2

SPEED. The behavior of this

LED is the same as LAN2

RJ45 LED1:

Pin 1: 100 Mbps- (Low Active)

Pin 2: 1000 Mbps- (Low

Active)

J33 is for connecting an

external LED to indicate LAN1

SPEED. The behavior of this

LED is the same as LAN1

RJ45 LED1:

Pin 1: 100 Mbps- (Low Active)

Pin 2: 1000 Mbps- (Low

Active)

17

http://www.tyan.com

2.4.8 –SMDC CON25X2_M3291 (J40)

2.4.9– Clear CMOS Jumper (JP1)

Pin_3 Pin_1

Normal

Pin_3 Pin_1

Clear

You can reset the CMOS settings by using

this jumper if you have forgotten your

system/setup password or need to clear

system BIOS setting.

- Power off system and disconnect

both power connectors from the

motherboard

- Use jumper cap to close Pin_2 and

Pin_3 for several seconds to Clear

CMOS

- Put jumper cap back to Pin_1 and

Pin_2 (default setting)

Reconnect power & power on system

For connection with Tyan Server

Management Daughter Card (SMDC).

The SMDC connector is compatible with

only the Tyan M3291 (SMDC).

18

http://www.tyan.com

2.4.10 – LAN1 & LAN2 Enable / Disable Jumper (JP2, JP3)

OPEN - Enable

CLOSED– Disable

JP2: LAN1 Enable/Disable

JP3: LAN2 Enable/Disable

2.4.11 – PCI-X Frequency Configure (JP24)

OPEN - Jumper OFF

CLOSED - Jumper ON

JP24 is used to adjust PCI-X frequency.

Open(Default):133MHz/100MHz/66MHz;

Closed: 100MHz/66MHz

19

http://www.tyan.com

2.4.12 – FAN Headers

Use these headers to connect the 3-pin or 4-pin

cooling fans to your motherboard to keep the

system stable and reliable.

These connectors support the tachometer

monitoring and auto fan speed control.

FAN1: CPUFAN (4-pin)

FAN2,FAN3,FAN4,FAN5:System FAN (4-pin)

20

http://www.tyan.com

2.4.13 - OEM Reserved Connectors and Jumpers

The connectors and jumpers, which are not listed, are reserved for OEM use only.

Page is loading ...

Tyan S5197 User manual

This manual is also suitable for

Tyan S5197 User manual

Related papers

Other documents