Panasonic SCHTB570EB Operating instructions

Category
Speaker sets
Type
Operating instructions

This manual is also suitable for

until
2013/01/30
EG EB
Operating Instructions
Home Theater Audio System
Model No. SC-HTB570
Thank you for purchasing this product.
Please read these instructions carefully before using this product, and save this manual for future use.
Model number suffix “EB” denotes UK model.
RQT9785-B
SC-HTB570_RQT9785-B_mst.book 1 ページ 2013年1月10日 木曜日 午後2時56分
2
RQT9785
Table of contents
Safety precautions
Unit
To reduce the risk of fire, electric shock or
product damage,
jDo not expose this unit to rain, moisture,
dripping or splashing.
jDo not place objects filled with liquids, such
as vases, on this unit.
jUse only the recommended accessories.
jDo not remove covers.
jDo not repair this unit by yourself. Refer
servicing to qualified service personnel.
AC mains lead
To reduce the risk of fire, electric shock or
product damage,
jEnsure that the power supply voltage
corresponds to the voltage printed on this
unit.
jInsert the mains plug fully into the socket
outlet.
jDo not pull, bend, or place heavy items on the
lead.
jDo not handle the plug with wet hands.
jHold onto the mains plug body when
disconnecting the plug.
jDo not use a damaged mains plug or socket
outlet.
The mains plug is the disconnecting device.
Install this unit so that the mains plug can be
unplugged from the socket outlet immediately.
Button-type battery (Lithium battery)
Risk of fire, explosion and burns. Do not
recharge, disassemble, heat above 60
o
C or
incinerate.
Keep the Button-Type battery out of the reach of
children. Never put Button-Type battery in
mouth. If swallowed call your doctor.
Unit
Do not place sources of naked flames, such as
lighted candles, on this unit.
This unit may receive radio interference caused
by mobile telephones during use. If such
interference occurs, please increase separation
between this unit and the mobile telephone.
This unit is intended for use in moderate
climates.
Placement
Place this unit on an even surface.
To reduce the risk of fire, electric shock or
product damage,
jDo not install or place this unit in a bookcase,
built-in cabinet or in another confined space.
Ensure this unit is well ventilated.
jDo not obstruct this unit’s ventilation openings
with newspapers, tablecloths, curtains, and
similar items.
jDo not expose this unit to direct sunlight, high
temperatures, high humidity, and excessive
vibration.
Button-type battery (Lithium battery)
Danger of explosion if battery is incorrectly
replaced. Replace only with the type
recommended by the manufacturer.
Insert with poles aligned.
Mishandling of batteries can cause electrolyte
leakage and may cause a fire.
jRemove the battery if you do not intend to use
the remote control for a long period of time.
Store in a cool, dark place.
jDo not heat or expose to flame.
jDo not leave the battery(ies) in a car exposed
to direct sunlight for a long period of time with
doors and windows closed.
When disposing the batteries, please contact
your local authorities or dealer and ask for the
correct method of disposal.
WARNING CAUTION
SC-HTB570_RQT9785-B_mst.book 2 ページ 2013年1月10日 木曜日 午後2時56分
Precautions
RQT9785
3
Caution for AC Mains
Lead
(For the AC mains plug of three pins)
For your safety, please read the following text
carefully.
This appliance is supplied with a moulded three
pin mains plug for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please
ensure that the replacement fuse has a rating of
5-ampere and that it is approved by ASTA or BSI
to BS1362.
Check for the ASTA mark Ï or the BSI mark Ì
on the body of the fuse.
If the plug contains a removable fuse cover you
must ensure that it is refitted when the fuse is
replaced.
If you lose the fuse cover the plug must not be
used until a replacement cover is obtained.
A replacement fuse cover can be purchased from
your local dealer.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to the type
of AC mains plug (figures A and B). Confirm the AC
mains plug fitted and follow the instructions below.
Illustrations may differ from actual AC mains plug.
1. Open the fuse cover with a screwdriver.
2. Replace the fuse and close or attach the fuse cover.
About Bluetooth
®
Frequency band used
This system uses the 2.4 GHz frequency band.
Certification of this device
This system conforms to frequency restrictions
and has received certification based on frequency
laws. Thus, a wireless permit is not necessary.
The action below are punishable by law in some countries:
jTaking apart or modifying the unit.
jRemoving specification indications.
Restrictions of use
Wireless transmission and/or usage with all
Bluetooth
®
equipped devices is not guaranteed.
All devices must conform to standards set by
Bluetooth SIG, Inc.
Depending on the specifications and settings of
a device, it can fail to connect or some
operations can be different.
This system supports Bluetooth
®
security
features. But depending on the operating
environment and/or settings, this security is
possibly not sufficient. Transmit data wirelessly
to this system with caution.
This system cannot transmit data to a Bluetooth
®
device.
Range of use
Use this device at a maximum range of 10 m.
The range can decrease depending on the
environment, obstacles or interference.
Interference from other devices
This system may not function properly and
troubles such as noise and sound jumps may
arise due to radio wave interference if the main
unit is located too close to other Bluetooth
®
devices or the devices that use the 2.4 GHz band.
This system may not function properly if radio waves
from a nearby broadcasting station, etc. are too strong.
Intended usage
This system is for normal, general use only.
Do not use this system near equipment or in an
environment that is sensitive to radio frequency
interference (example: airports, hospitals,
laboratories, etc.).
Figure A Figure B
Fuse cover
Figure A Figure B
Fuse
(5 ampere)
Fuse
(5 ampere)
Panasonic bears no responsibility for data
and/or information that is compromised
during a wireless transmission.
SC-HTB570_RQT9785-B_mst.book 3 ページ 2013年1月10日 木曜日 午後2時56分
4
RQT9785
Table of contents
Safety precautions ........................................................................................... 2
Caution for AC Mains Lead ............................................................................. 3
About Bluetooth
®
............................................................................................. 3
Before use
Supplied items .................................................................................................. 5
This system (SC-HTB570) .................................................................................................. 5
Accessories ........................................................................................................................ 5
Control reference guide ................................................................................... 6
This system (Front) ............................................................................................................. 6
This system (Rear) .............................................................................................................7
Remote control ................................................................................................................... 8
Getting started
Step 1 Selecting the placement method ....................................................... 9
The speaker system ......................................................................................................... 10
The active subwoofer ....................................................................................................... 10
Wireless interference ........................................................................................................ 10
Step 2 Assembling the speakers ................................................................. 11
When attaching the speakers to a wall ............................................................................. 11
When placing the speakers on a table ............................................................................. 16
Additional speaker fall prevention measures .................................................................... 20
Step 3 Connections ....................................................................................... 22
Connection with the TV .................................................................................................... 22
Connection with other devices .......................................................................................... 23
Speaker cable connection ................................................................................................ 24
AC mains lead connection ................................................................................................ 24
Active subwoofer wireless connection .............................................................................. 25
Bluetooth
®
connection ...................................................................................................... 25
Operations
Using this system .......................................................................................... 26
3D sound ......................................................................................................... 27
Sound modes ................................................................................................................... 27
Linked operations with the TV (VIERA Link “HDAVI Control
TM
”) .............. 28
Advanced operations ..................................................................................... 29
Reference
Troubleshooting ............................................................................................. 31
Indicator illumination ..................................................................................... 34
Specifications ................................................................................................. 35
Unit care .......................................................................................................... 36
Licenses .......................................................................................................... 36
SC-HTB570_RQT9785-B_mst.book 4 ページ 2013年1月10日 木曜日 午後2時56分
Getting started
Operations
Reference
Before use
Precautions
RQT9785
5
Before use
Supplied items
Check the supplied accessories before using this system.
Product numbers are correct as of December 2012. These may be subject to change.
The supplied AC mains lead is for use with this system only.
Do not use it with other equipment. Also, do not use cords from other equipment with this system.
The illustrations shown may differ from your unit.
These operation instructions are applicable to model SC-HTB570 for variety of regions.
Unless otherwise indicated, illustrations in these operating instructions are of the model for
the United Kingdom and Ireland.
Operations in this operating instructions are described mainly with the remote control, but
you can perform the operations on the main unit if the controls are the same.
This system (SC-HTB570)
1 Main unit
(SU-HTB570)
1 Active subwoofer
(SB-HWA570)
2 Front speakers
(SB-HTB570)
Accessories
1 Remote control
(with a battery)
(N2QAYC000083)
AC mains lead
2 For the United
Kingdom and Ireland
(K2CT2YY00097)
2 For Continental
Europe
(K2CQ2YY00119)
2 Speaker cables
(REE1789: RED)
(REE1790: WHITE)
Length: 3 m
1 Metal bracket
(RML0761)
4 Screws
(XYN5+J14FJK)
2 Speaker feet
(RKAX0042-K)
2 Stand necks
(RGK2444)
2 Support legs
(RGK2464)
2 Leg stands
(RGK2463)
2 Speaker bases
(RGK2465)
SC-HTB570_RQT9785-B_mst.book 5 ページ 2013年1月10日 木曜日 午後2時56分
6
RQT9785
Control reference guide
1 Standby/on switch (Í/I)
Press to switch the unit from on to standby
mode or vice versa. In standby mode, the unit
is still consuming a small amount of power.
2 Adjust the volume of this system
3 Select the input source
“TV”#“BD/DVD”#“AUX”
^-------- “”(--------------}
4 Input selector indicators*
1
A Bluetooth
®
indicator
Lights blue when the Bluetooth
®
device is
the audio source
B TV indicator
Lights green when the TV is the audio
source
C BD/DVD indicator
Lights amber when the device connected
to the BD/DVD terminal is the audio
source
D AUX indicator
Lights amber when the device connected
to the AUX terminal is the audio source
5 Sound mode indicators*
1
E STANDARD indicator
Lights when STANDARD is the current
sound mode
F STADIUM indicator*
2
Lights when STADIUM is the current
sound mode
G MUSIC indicator*
2
Lights when MUSIC is the current sound
mode
H CINEMA indicator
Lights when CINEMA is the current
sound mode
I NEWS indicator
Lights when NEWS is the current sound
mode
J STEREO indicator
Lights when STEREO is the current
sound mode
6 Remote control signal sensor (> 8)
7 WIRELESS LINK indicator (> 25)
*1
The indicators will also blink in various conditions. (> 34)
*2
The indicator blinks for 5 sec when the main unit detects an audio format.
To manually verify the current audio format and the corresponding indicators, refer to page 29 (Audio
format indicator).
This system (Front)
7
456
1
2
3
Main unit
Active subwoofer
SC-HTB570_RQT9785-B_mst.book 6 ページ 2013年1月10日 木曜日 午後2時56分
Before use
RQT9785
7
1 AC IN terminal (> 24)
2 Speaker terminals (> 24)
3 OPTICAL DIGITAL AUDIO IN (TV) terminal
(> 22)
4 OPTICAL DIGITAL AUDIO IN (AUX) terminal
(> 23)
5 USB port (for service use only)
6 HDMI IN terminal (> 23)
7 HDMI OUT terminal (ARC compatible)
(> 22)
8 Active subwoofer on/off button (> 25)
* The I/D SET button is only used when the main unit is not paired with the active subwoofer. (> 33)
This system (Rear)
*
AV OUT
TV(ARC)
AV IN
BD/DVD
AV OUT
TV(ARC)
AV IN
BD/DVD
SC-HTB570_RQT9785-B_mst.book 7 ページ 2013年1月10日 木曜日 午後2時56分
8
RQT9785
1 Turn the main unit on or off (> 26)
2 Adjust the dialog effect level (> 26)
3 Adjust the output level of the active
subwoofer (bass sound) (> 26)
4 Adjust the volume of this system (> 26)
5 Mute the sound (> 26)
6 Select the input source (> 26)
“TV”#“BD/DVD” #“AUX”
^------------ “”(---------}
7 Select the Bluetooth
®
device as the source
(> 26)
8 Select the sound mode (> 27)
“STANDARD” ----#“STADIUM” -----#“MUSIC”
^- “STEREO( “NEWS”( “CINEMA”(}
Remote control operation range
The remote control signal sensor is located on the main unit.
Use the remote control within the correct operation range.
Remote control
DIALOG LEVEL
LINK MODE
PAIRING
----
SOUND
1
6
7
2
3
4
5
8
INPUT
SELECTOR
Before using for the first time
Remove the insulation sheet A.
To replace a button-type battery
Battery type: CR2025 (Lithium battery)
Set the button-type battery with its (i) mark
facing upward.
Keep the button-type battery out of reach of
children to prevent swallowing.
B Remote control signal sensor
Operation range
Distance: Within approx. 7 m
directly in front
Angle: Approx. 30
o
left and right
SC-HTB570_RQT9785-B_mst.book 8 ページ 2013年1月10日 木曜日 午後2時56分
Getting started
Before use
RQT9785
9
Getting started
Step 1 Selecting the placement method
Choose a placement method that suits you best.
When attaching the speakers to a wall
When placing the speakers on a table
Place the speakers
horizontally
Page 11
Place the speakers
vertically
Place the speakers using
the leg stands
Place the speakers using
the speaker bases
Page 14
Page 16
Page 17
Page 18
Place the speakers using
the support legs and
speaker feet
SC-HTB570_RQT9785-B_mst.book 9 ページ 2013年1月10日 木曜日 午後2時56分
10
RQT9785
Use a screwdriver (i) for assembling the speakers.
Do not hold the speakers in one hand to avoid injury, you may drop the speakers when carrying them.
When carrying the active subwoofer
To avoid interference, maintain the following distances between the main unit/active subwoofer
and other electronic devices that use the same radio frequency (2.4 GHz band).
Place the active subwoofer within a few meters of the main unit and in a horizontal position with the top panel facing upward.
Do not use the main unit or the active subwoofer in a metal cabinet.
Placing the active subwoofer too close to the walls and corners can result in excessive bass. Cover walls and windows with thick curtains.
If irregular colouring occurs on your TV, turn the TV off for about 30 minutes. If it persists, move the speakers further away from the TV.
Keep magnetised items away. Magnetised cards, watches, etc., can be damaged if placed too close to the active subwoofer and the speakers.
Caution
This system is to be used only as indicated in these instructions. Failure to do so may lead to damage to the amplifier and/
or the speakers, and may result in the risk of fire. Consult a qualified service person if damage has occurred or if you
experience a sudden change in performance.
Do not attempt to attach the speakers to a wall using methods other than those described in this manual.
The speaker system
When attaching the speakers to a wall
The wall or pillar on which the speakers are to be attached should be capable of supporting 33 kg per screw. Consultation with
a qualified installation specialist is recommended when attaching the speakers to a wall. Improper attachment may result in
damage to the wall and speakers, and personal injury.
When placing the speakers in front of the TV
The speakers may block or interfere with the TV’s various sensors (C.A.T.S. (Contrast Automatic Tracking System) sensor,
remote control sensor, etc.) and the 3D Eyewear transmitters on a 3D compatible TV.
If the leg stands are being used
Change the height of the leg stands and/or move the speakers further away from the TV. If the TV still does not function
correctly, try removing the leg stands.
If the leg stands are not used
Move the speakers further away from the TV. If the TV still does not function properly, try placing them beside the TV (> 9).
The active subwoofer
A Do not hold the active subwoofer from this
opening.
The parts inside may get damaged.
B Always hold the bottom of the active subwoofer when
moving it.
Wireless interference
C Main unit/active subwoofer
D Wireless router, cordless phone and other
electronic devices: approx. 2 m
A
B
D
C
SC-HTB570_RQT9785-B_mst.book 10 ページ 2013年1月10日 木曜日 午後2時56分
Getting started
RQT9785
11
Step 2 Assembling the speakers
The speakers can be wall mounted by drilling screws into the wall, etc.
Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg.
The screws and other items are not supplied as the type and size will vary with each installation.
For details about the required screws, refer to the diagram below the step “Drive a screw into the wall.”.
For a safety measure to prevent the speakers from falling, refer to page 20.
To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
Assemble the speakers.
The two speakers are interchangeable.
Keep the screws out of reach of children to prevent swallowing.
When attaching the speakers to a wall
Place the speakers horizontally
2 Speakers 2 Speaker cables
WHITE: Left
RED: Right
1 Metal bracket
2 Screws
A Screw (supplied)
Tighten securely.
SC-HTB570_RQT9785-B_mst.book 11 ページ 2013年1月10日 木曜日 午後2時56分
12
RQT9785
Connect the speaker cables.
If the speaker cable is twisted, it might not fit through the opening. Straighten the speaker cable before inserting.
Insert the wire fully, taking care not to insert beyond the wire insulation.
Drive a screw into the wall.
Use the measurements indicated below to identify the screwing positions on the wall.
Leave at least 20 mm of space above and on each side of the speaker to allow enough space for fitting the speaker.
Keep the screws out of reach of children to prevent swallowing.
1 Insert the wire fully.
r: White
s: Blue line
2 Press into the
groove.
A Right speaker
connector
B Left speaker connector
A At least 30 mm
B 4.0 mm
C 7.0 mm to 9.4 mm
D Wall or pillar
E 5.5mm to 6.5mm
F 238 mm G 576 mm H 248 mm I 20 mm
J Wall mounting hole
White
Red
Push

SC-HTB570_RQT9785-B_mst.book 12 ページ 2013年1月10日 木曜日 午後2時56分
Getting started
RQT9785
13
Fit the speaker securely onto the screw(s).
A Right speaker connector
B Left speaker connector
Red connector: The speaker attached to the red connector cable is to be placed on the right side.
White connector:The speaker attached to the white connector cable is to be placed on the left side.
DO DO NOT
Move the speaker so
that the screw is in
this position.
In this position, the
speaker will likely fall
if moved to the left or
right.
White
Red
SC-HTB570_RQT9785-B_mst.book 13 ページ 2013年1月10日 木曜日 午後2時56分
14
RQT9785
The speakers can be wall mounted by drilling screws into the wall, etc.
Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg.
The screws and other items are not supplied as the type and size will vary with each installation.
For details about the required screws, refer to the diagram below the step “Drive a screw into the wall.”.
For a safety measure to prevent the speakers from falling, refer to page 20.
To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
Attach the stand neck.
The two speakers are interchangeable.
Keep the screws out of reach of children to prevent swallowing.
A Screw (supplied)
Tighten securely.
Connect the speaker cables.
If the speaker cable is twisted, it might not fit through the opening. Straighten the speaker cable before inserting.
Insert the wire fully, taking care not to insert beyond the wire insulation.
Place the speakers vertically
2 Speakers 2 Speaker cables
WHITE: Left
RED: Right
2 Stand
necks
2 Screws
1 Insert the wire fully.
r: White
s: Blue line
2 Press into the groove.
Push
SC-HTB570_RQT9785-B_mst.book 14 ページ 2013年1月10日 木曜日 午後2時56分
Getting started
RQT9785
15
Drive a screw into the wall.
Use the measurements indicated below to identify the
screwing positions on the wall.
Leave at least 20 mm of space above and on each side of
the speaker to allow enough space for fitting the speaker.
Keep the screws out of reach of children to prevent
swallowing.
A At least 30 mm
B 4.0 mm
C 7.0 mm to 9.4 mm
D Wall or pillar
E 5.5 mm to 6.5 mm
Fit the speaker(s) securely onto the screw(s).
F Front speaker
(Rear view)
G 100 mm
H 436 mm
I 34 mm
J Wall mounting hole
Red connector: The speaker attached to the red connector cable is to be placed on the right side.
White connector:The speaker attached to the white connector cable is to be placed on the left side.
K Left speaker connector L Right speaker connector
DO DO NOT
Move the speaker so
that the screw is in this
position.
In this position, the
speaker will likely fall if
moved to the left or
right.
Red
White
SC-HTB570_RQT9785-B_mst.book 15 ページ 2013年1月10日 木曜日 午後2時56分
16
RQT9785
For a safety measure to prevent the speakers from falling, refer to page 20.
To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
Assemble the speakers following steps 1 and 2 of “Place the speakers
horizontally” (> 11, 12).
Attach the leg stands.
Keep the screws out of reach of children to prevent swallowing.
When placing the speakers on a table
Place the speakers using the leg stands
2 Speakers 2 Speaker cables
WHITE: Left
RED: Right
1 Metal bracket
2 Leg stands 4 Screws
Red connector:
With the speaker facing down, the speaker attached to the red connector cable is
to be placed on the left side.
White connector:
With the speaker facing down, the speaker attached to the white connector cable
is to be placed on the right side.
A Screw (supplied)
Tighten securely.
B Screw hole
C Right speaker connector
D Left speaker connector
Align the higher or lower holes with the projecting parts on
the speaker.
By changing the position that the stand is attached to the
projecting parts, the height can be adjusted by 9 mm.
White
Red
SC-HTB570_RQT9785-B_mst.book 16 ページ 2013年1月10日 木曜日 午後2時56分
Getting started
RQT9785
17
For a safety measure to prevent the speakers from falling, refer to page 20.
To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
Assemble the speakers following steps 1 and 2 of “Place the speakers
horizontally” (> 11, 12).
Attach the support legs and speaker feet.
Keep the screws and the speaker feet out of reach of children to prevent swallowing.
Place the speakers using the support legs and
speaker feet
2 Speakers 2 Speaker cables
WHITE: Left
RED: Right
1 Metal
bracket
2 Support legs 4 Screws 2 Speaker feet
Red connector:
With the speaker facing down, the speaker attached to the red connector cable is
to be placed on the left side.
White connector:
With the speaker facing down, the speaker attached to the white connector cable
is to be placed on the right side.
A Screw (supplied)
Tighten securely.
B Screw hole
C Speaker foot (supplied)
D Right speaker connector
E Left speaker connector
Align the projecting
parts on the speaker
with support leg.
Red
White
SC-HTB570_RQT9785-B_mst.book 17 ページ 2013年1月10日 木曜日 午後2時56分
18
RQT9785
For a safety measure to prevent the speakers from falling, refer to page 20.
To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
Assemble the speakers following step 1 of “Place the speakers
vertically” (> 14).
Insert the speaker cable through the speaker base and connect the
speaker cables.
Be sure to insert the speaker cable through the threading hole as indicated in the illustration. (If the speaker cable is
twisted, it might not fit through the opening. Straighten the speaker cable before inserting.)
Insert the wire fully, taking care not to insert beyond the wire insulation.
Place the speakers using the speaker
bases
2 Speakers 2 Speaker cables
WHITE: Left
RED: Right
2 Stand necks
2 Speaker bases 4 Screws
1 Insert the wire fully.
r: White
s: Blue line
2 Press into the groove.
Push
SC-HTB570_RQT9785-B_mst.book 18 ページ 2013年1月10日 木曜日 午後2時56分
Getting started
RQT9785
19
Attach the speaker base.
The two speakers are interchangeable.
Keep the screws out of reach of children to prevent swallowing.
Red connector: The speaker attached to the red connector cable is to be placed on the right side.
White connector: The speaker attached to the white connector cable is to be placed on the left side.
Screw (supplied)
Tighten securely.
Align the projecting
parts with the holes
on the speaker.
Press into the groove.
SC-HTB570_RQT9785-B_mst.book 19 ページ 2013年1月10日 木曜日 午後2時56分
20
RQT9785
To prevent the speakers from falling, it is recommended, as an additional protection
measure, to attach the speakers to the wall or table with a fall prevention cord (hereafter
“cord”).
Consultation with a qualified installation specialist concerning the appropriate procedure when attaching to a concrete wall or
a surface that may not have strong enough support is recommended (> 12, 15). Improper attachment may result in damage
to the wall and speakers, and personal injury.
Use a cord that is capable of supporting over 10 kg (with a diameter of about 1.5 mm).
The speaker fall prevention measure is to minimize the possibility of damage and harm, but it does not completely guarantee this effect.
Keep the screws out of reach of children to prevent swallowing.
Make sure that the slack of the cord is minimal.
Depending on the placement of the speakers, the screwing position of the screw eye may differ.
Additional speaker fall prevention measures
When attaching the speakers horizontally
A Cord* B Screw eye C Wall
* If the cord cannot be threaded through the holes, try bending the cord in 2 locations, about
10 mm apart from the tip, at an angle of 45
o
(as
illustrated above).
C
A
C
B
A
Wall mounting
On a table
SC-HTB570_RQT9785-B_mst.book 20 ページ 2013年1月10日 木曜日 午後2時56分
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Panasonic SCHTB570EB Operating instructions

Category
Speaker sets
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI