Panasonic SC-HTB770 Operating instructions

Brand: Panasonic

Model: SC-HTB770

Category: Speaker sets

Type: Operating instructions

until

2013/03/26

EG EB GN

Operating Instructions

Home Theater Audio System

Model No. SC-HTB770

Thank you for purchasing this product.

Please read these instructions carefully before using this product, and save this manual for future use.

Model number suffix “EB” denotes UK model.

RQT9849-B

SC-HTB770_RQT9849-B_mst.book 1 ページ２０１３年２月２５日　月曜日　午前１１時５３分

RQT9849

Table of contents

Safety precautions

Unit

≥ To reduce the risk of fire, electric shock or

product damage,

jDo not expose this unit to rain, moisture,

dripping or splashing.

jDo not place objects filled with liquids, such

as vases, on this unit.

jUse only the recommended accessories.

jDo not remove covers.

jDo not repair this unit by yourself. Refer

servicing to qualified service personnel.

AC mains lead

≥ To reduce the risk of fire, electric shock or

product damage,

jEnsure that the power supply voltage

corresponds to the voltage printed on this

unit.

jInsert the mains plug fully into the socket

outlet.

jDo not pull, bend, or place heavy items on the

lead.

jDo not handle the plug with wet hands.

jHold onto the mains plug body when

disconnecting the plug.

jDo not use a damaged mains plug or socket

outlet.

≥ The mains plug is the disconnecting device.

Install this unit so that the mains plug can be

unplugged from the socket outlet immediately.

Button-type battery (Lithium battery)

≥ Risk of fire, explosion and burns. Do not

recharge, disassemble, heat above 60

C or

incinerate.

≥ Keep the Button-Type battery out of the reach of

children. Never put Button-Type battery in

mouth. If swallowed call your doctor.

Unit

≥ Do not place sources of naked flames, such as

lighted candles, on this unit.

≥ This unit may receive radio interference caused

by mobile telephones during use. If such

interference occurs, please increase separation

between this unit and the mobile telephone.

≥ This unit is intended for use in moderate

climates.

Placement

≥ Place this unit on an even surface.

≥ To reduce the risk of fire, electric shock or

product damage,

jDo not install or place this unit in a bookcase,

built-in cabinet or in another confined space.

Ensure this unit is well ventilated.

jDo not obstruct this unit’s ventilation openings

with newspapers, tablecloths, curtains, and

similar items.

jDo not expose this unit to direct sunlight, high

temperatures, high humidity, and excessive

vibration.

Button-type battery (Lithium battery)

≥ Danger of explosion if battery is incorrectly

replaced. Replace only with the type

recommended by the manufacturer.

≥ Insert with poles aligned.

≥ Mishandling of batteries can cause electrolyte

leakage and may cause a fire.

jRemove the battery if you do not intend to use

the remote control for a long period of time.

Store in a cool, dark place.

jDo not heat or expose to flame.

jDo not leave the battery(ies) in a car exposed

to direct sunlight for a long period of time with

doors and windows closed.

≥ When disposing the batteries, please contact

your local authorities or dealer and ask for the

correct method of disposal.

WARNING CAUTION

SC-HTB770_RQT9849-B_mst.book 2 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Precautions

RQT9849

Caution for AC Mains

Lead

(For the AC mains plug of three pins)

For your safety, please read the following text

carefully.

This appliance is supplied with a moulded three

pin mains plug for your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please

ensure that the replacement fuse has a rating of

5-ampere and that it is approved by ASTA or BSI

to BS1362.

Check for the ASTA mark Ï or the BSI mark Ì

on the body of the fuse.

If the plug contains a removable fuse cover you

must ensure that it is refitted when the fuse is

replaced.

If you lose the fuse cover the plug must not be

used until a replacement cover is obtained.

A replacement fuse cover can be purchased from

your local dealer.

Before use

Remove the connector cover.

How to replace the fuse

The location of the fuse differ according to the type

of AC mains plug (figures A and B). Confirm the AC

mains plug fitted and follow the instructions below.

Illustrations may differ from actual AC mains plug.

1. Open the fuse cover with a screwdriver.

2. Replace the fuse and close or attach the fuse cover.

About Bluetooth

∫ Frequency band used

This system uses the 2.4 GHz frequency band.

∫ Certification of this device

≥

This system conforms to frequency restrictions

and has received certification based on frequency

laws. Thus, a wireless permit is not necessary.

≥

The action below are punishable by law in some countries:

jTaking apart or modifying the unit.

jRemoving specification indications.

∫ Restrictions of use

≥ Wireless transmission and/or usage with all

Bluetooth

equipped devices is not guaranteed.

≥ All devices must conform to standards set by

Bluetooth SIG, Inc.

≥ Depending on the specifications and settings of

a device, it can fail to connect or some

operations can be different.

≥ This system supports Bluetooth

security

features. But depending on the operating

environment and/or settings, this security is

possibly not sufficient. Transmit data wirelessly

to this system with caution.

≥

This system cannot transmit data to a Bluetooth

device.

∫ Range of use

Use this device at a maximum range of 10 m.

The range can decrease depending on the

environment, obstacles or interference.

∫ Interference from other devices

≥

This system may not function properly and

troubles such as noise and sound jumps may

arise due to radio wave interference if the main

unit is located too close to other Bluetooth

devices or the devices that use the 2.4 GHz band.

≥

This system may not function properly if radio waves

from a nearby broadcasting station, etc. are too strong.

∫ Intended usage

≥ This system is for normal, general use only.

≥ Do not use this system near equipment or in an

environment that is sensitive to radio frequency

interference (example: airports, hospitals,

laboratories, etc.).

Figure A Figure B

Fuse cover

Figure A Figure B

Fuse

(5 ampere)

Fuse

(5 ampere)

Panasonic bears no responsibility for data

and/or information that is compromised

during a wireless transmission.

SC-HTB770_RQT9849-B_mst.book 3 ページ２０１３年２月２５日　月曜日　午前１１時５３分

RQT9849

Table of contents

Safety precautions ........................................................................................... 2

Caution for AC Mains Lead ............................................................................. 3

About Bluetooth

............................................................................................. 3

Before use

Supplied items .................................................................................................. 5

This system (SC-HTB770) .................................................................................................. 5

Accessories ........................................................................................................................ 5

Control reference guide ................................................................................... 6

This system (Front) ............................................................................................................. 6

This system (Rear) .............................................................................................................7

Remote control ................................................................................................................... 8

Getting started

Step 1 Selecting the placement method ....................................................... 9

The speaker system ......................................................................................................... 10

The active subwoofer ....................................................................................................... 10

Wireless interference ........................................................................................................ 10

Step 2 Assembling the speakers ................................................................. 11

When attaching the speakers to a wall ............................................................................. 11

When placing the speakers on a table ............................................................................. 18

Additional speaker fall prevention measures .................................................................... 23

Step 3 Connections ....................................................................................... 25

Connection with the TV .................................................................................................... 25

Connection with other devices .......................................................................................... 26

Speaker cable connection ................................................................................................ 27

AC mains lead connection ................................................................................................ 27

Active subwoofer wireless connection .............................................................................. 28

Bluetooth

connection ...................................................................................................... 28

Operations

Using this system .......................................................................................... 29

3D sound ......................................................................................................... 30

Sound modes ................................................................................................................... 30

Linked operations with the TV (VIERA Link “HDAVI Control

”) .............. 31

Advanced operations ..................................................................................... 32

Reference

Troubleshooting ............................................................................................. 34

Indicator illumination ..................................................................................... 37

Specifications ................................................................................................. 38

Unit care .......................................................................................................... 39

Licenses .......................................................................................................... 39

Limited Warranty (ONLY FOR AUSTRALIA) ................................................ 43

SC-HTB770_RQT9849-B_mst.book 4 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Getting started

Operations

Reference

Before use

Precautions

RQT9849

Before use

Supplied items

Check the supplied accessories before using this system.



≥ Product numbers are correct as of February 2013. These may be subject to change.

≥ The supplied AC mains lead is for use with this system only.

Do not use it with other equipment. Also, do not use cords from other equipment with this system.

≥ The illustrations shown may differ from your unit.

≥ These operation instructions are applicable to model SC-HTB770 for variety of regions.

Unless otherwise indicated, illustrations in these operating instructions are of the model for the United Kingdom and Ireland.

≥ Operations in this operating instructions are described mainly with the remote control, but you can

perform the operations on the main unit if the controls are the same.

This system (SC-HTB770)

∏ 1 Main unit

(SU-HTB770)

∏ 1

Active subwoofer

(SB-HWA770)

∏ 1 Centre speaker

(SB-HTB770)

∏ 2 Front speakers

(SB-HTB570)

Accessories

∏ 1 Remote control

(with a battery)

(N2QAYC000083)

∏ AC mains lead

2 For the United

Kingdom and Ireland

(K2CT2YY00097)

2 For Continental

Europe

(K2CQ2YY00119)

2 For Australia and

New Zealand

(K2CJ2YY00093)

∏ 3 Speaker cables

(REE1789: RED)

(REE1790: WHITE)

Length: 3 m

(REE1791: GREEN)

Length: 2 m

∏ 1 Metal bracket

(RML0760)

∏ 2 Stand necks

(RGK2444)

∏ 2 Support legs

(RGK2464)

∏ 2 Leg stands

(RGK2463)

∏ 2 Side caps

(RGK2445: R)

(RGK2446: L)

∏ 2 Hook brackets

(RML0763)

∏ 2 Speaker bases

(RGK2465)

∏ 6

Screws (XYN5+J14FJK)

∏ 2 Speaker feet

(RKAX0042-K)

SC-HTB770_RQT9849-B_mst.book 5 ページ２０１３年２月２５日　月曜日　午前１１時５３分

RQT9849

Control reference guide

1 Standby/on switch (Í/I)

Press to switch the unit from on to standby

mode or vice versa. In standby mode, the unit

is still consuming a small amount of power.

2 Adjust the volume of this system

3 Select the input source

“TV”---------#“BD/DVD”---------#“AUX1”

^-- “”(- “AUX3”(- “AUX2”(}

4 Input selector indicators*

A Bluetooth

indicator

Lights blue when the Bluetooth

device is

the audio source

B TV indicator

Lights green when the TV is the audio

source

C BD/DVD indicator

Lights amber when the device connected

to the BD/DVD terminal is the audio

source

D AUX1 indicator

Lights amber when the device connected

to the AUX1 terminal is the audio source

E AUX2 indicator

Lights amber when the device connected

to the AUX2 terminal is the audio source

F AUX3 indicator

Lights amber when the device connected

to the AUX3 terminal is the audio source

5 Sound mode indicators*

G STANDARD indicator

Lights when STANDARD is the current

sound mode

H STADIUM indicator*

Lights when STADIUM is the current

sound mode

I MUSIC indicator*

Lights when MUSIC is the current sound

mode

J CINEMA indicator

Lights when CINEMA is the current

sound mode

K NEWS indicator

Lights when NEWS is the current sound

mode

L STEREO indicator

Lights when STEREO is the current

sound mode

6 Remote control signal sensor (> 8)

7 WIRELESS LINK indicator (> 28)

The indicators will also blink in various conditions. (> 37)

The indicator blinks for 5 sec when the main unit detects an audio format.

To manually verify the current audio format and the corresponding indicators, refer to page 32 (Audio

format indicator).

This system (Front)

456

Main unit

Active subwoofer

SC-HTB770_RQT9849-B_mst.book 6 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Before use

RQT9849

1 AC IN terminal (> 27)

2 Speaker terminals (> 27)

3 TV terminal (> 25)

4 AUX3 terminal (> 26)

5 USB port (for service use only)

6 AUX2 terminal (> 26)

7 AUX1 terminal (> 26)

8 BD/DVD terminal (> 26)

9 HDMI OUT terminal (ARC compatible) (

25)

10 Active subwoofer on/off button (> 28)

* The I/D SET button is only used when the main unit is not paired with the active subwoofer. (> 36)

This system (Rear)

AV IN

(ARC)

BD/DVD

AUX1

(HDMI1)

(HDMI2)

AUX2

(HDMI3)

AV OUT

AV IN

(ARC)

BD/DVD

AUX1

(HDMI1)

(HDMI2)

AUX2

(HDMI3)

AV OUT

SC-HTB770_RQT9849-B_mst.book 7 ページ２０１３年２月２５日　月曜日　午前１１時５３分

RQT9849

1 Turn the main unit on or off (> 29)

2 Adjust the dialog effect level (> 29)

3 Adjust the output level of the active

subwoofer (bass sound) (> 29)

4 Adjust the volume of this system (> 29)

5 Mute the sound (> 29)

6 Select the input source (> 29)

“TV”---------#“BD/DVD”---------#“AUX1”

^--- “”( “AUX3”( “AUX2”(}

7 Select the Bluetooth

device as the source

(> 29)

8 Select the sound mode (> 30)

“STANDARD” ----#“STADIUM” -----#“MUSIC”

^- “STEREO”( “NEWS”( “CINEMA”(}

∫ Remote control operation range

The remote control signal sensor is located on the main unit.

≥Use the remote control within the correct operation range.

Remote control

DIALOG LEVEL

LINK MODE

PAIRING

----

SOUND

INPUT

SELECTOR

∫ Before using for the first time

Remove the insulation sheet A.

∫ To replace a button-type battery

Battery type: CR2025 (Lithium battery)

≥ Set the button-type battery with its (i) mark

facing upward.

≥ Keep the button-type battery out of reach of

children to prevent swallowing.







B Remote control signal sensor

≥ Operation range

Distance: Within approx. 7 m

directly in front

Angle: Approx. 30

left and right

SC-HTB770_RQT9849-B_mst.book 8 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Getting started

Before use

RQT9849

Getting started

Step 1 Selecting the placement method

≥Choose a placement method that suits you best.

When attaching the speakers to a wall

When placing the speakers on a table

Place the speakers

horizontally

Page 11

Place the front speakers

vertically

Place the speakers using

the leg stands

Place the front speakers

using the speaker bases

Page 14

Page 18

Page 19

Page 20

Place the speakers using

the support legs and

speaker feet

SC-HTB770_RQT9849-B_mst.book 9 ページ２０１３年２月２５日　月曜日　午前１１時５３分

RQT9849

≥Use a screwdriver (i) for assembling the speakers.

≥Do not hold the speakers in one hand to avoid injury, you may drop the speakers when carrying them.

When carrying the active subwoofer

To avoid interference, maintain the following distances between the main unit/active subwoofer

and other electronic devices that use the same radio frequency (2.4 GHz band).



≥ Place the active subwoofer within a few meters of the main unit and in a horizontal position with the top panel facing upward.

≥ Do not use the main unit or the active subwoofer in a metal cabinet.

≥

Placing the active subwoofer too close to the walls and corners can result in excessive bass. Cover walls and windows with thick curtains.

≥

If irregular colouring occurs on your TV, turn the TV off for about 30 minutes. If it persists, move the speakers further away from the TV.

≥

Keep magnetised items away. Magnetised cards, watches, etc., can be damaged if placed too close to the active subwoofer and the speakers.

Caution

≥ This system is to be used only as indicated in these instructions. Failure to do so may lead to damage to the amplifier and/

or the speakers, and may result in the risk of fire. Consult a qualified service person if damage has occurred or if you

experience a sudden change in performance.

≥ Do not attempt to attach the speakers to a wall using methods other than those described in this manual.

The speaker system

∫ When attaching the speakers to a wall

The wall or pillar on which the speakers are to be attached should be capable of supporting 33 kg per screw. Consultation with

a qualified installation specialist is recommended when attaching the speakers to a wall. Improper attachment may result in

damage to the wall and speakers, and personal injury.

∫ When placing the speakers in front of the TV

The speakers may block or interfere with the TV’s various sensors (C.A.T.S. (Contrast Automatic Tracking System) sensor,

remote control sensor, etc.) and the 3D Eyewear transmitters on a 3D compatible TV.

≥ If the leg stands are being used

Change the height of the leg stands and/or move the speakers further away from the TV. If the TV still does not function

correctly, try removing the leg stands.

≥ If the leg stands are not used

Move the speakers further away from the TV. If the TV still does not function properly, try placing them beside the TV (> 9).

The active subwoofer

A Do not hold the active subwoofer from this

opening.

The parts inside may get damaged.

B Always hold the bottom of the active subwoofer when

moving it.

Wireless interference

C Main unit/active subwoofer

D Wireless router, cordless phone and other

electronic devices: approx. 2 m

SC-HTB770_RQT9849-B_mst.book 10 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Getting started

RQT9849

Step 2 Assembling the speakers

The speakers can be wall mounted by drilling screws into the wall, etc.

Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg.

The screws and other items are not supplied as the type and size will vary with each installation.

≥

For details about the required screws, refer to the diagram below the step “Drive a screw into the wall.”

(

12).

≥For a safety measure to prevent the speakers from falling, refer to page 23.

≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.

Assemble the speakers.

≥ There is no left and right for the centre speaker.

≥ The two front speakers are interchangeable.

≥ Keep the screws out of reach of children to prevent swallowing.

When attaching the speakers to a wall

Place the speakers horizontally

∏ 2 Front

speakers

∏ 1 Centre

speaker

∏ 3 Speaker cables

WHITE: Left

RED: Right

GREEN: Centre

∏ 1 Metal bracket ∏ 4 Screws

A Screw (supplied)

≥ Tighten securely.



SC-HTB770_RQT9849-B_mst.book 11 ページ２０１３年２月２５日　月曜日　午前１１時５３分

RQT9849

Connect the speaker cables.

* If you have difficulty inserting the cable, try straightening the speaker cable and then bending the

cable about 20 mm from the tip, at an angle of approx. 45o

(as illustrated above).

Drive a screw into the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Leave at least 20 mm of space above and on each side of the speaker to allow enough space for fitting the speaker.

≥ Keep the screws out of reach of children to prevent swallowing.

1 Insert the wire fully.

r: White

s: Blue line

≥ Insert the wire fully, taking care not to insert

beyond the wire insulation.

2 Press into the groove.

A Right speaker connector

B Centre speaker connector

C Left speaker connector

A At least 30 mm

B ‰4.0 mm

C ‰7.0 mm to ‰9.4 mm

D Wall or pillar

E 5.5mm to 6.5mm

F 238 mm G 745 mm H 248 mm I 20 mm

J Wall mounting hole











Push

Red

White

Green











 













Front view (semi-transparent image)

SC-HTB770_RQT9849-B_mst.book 12 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Getting started

RQT9849

Wall mount the speakers:

Fit the speaker securely onto the screw(s).

A Right speaker connector

B Left speaker connector

Red connector: The speaker attached to the red connector cable is to be placed on the right side.

White connector:The speaker attached to the white connector cable is to be placed on the left side.

DO DO NOT

≥ Move the speaker so

that the screw is in

this position.

≥ In this position, the

speaker will likely fall

if moved to the left or

right.





White Red

SC-HTB770_RQT9849-B_mst.book 13 ページ２０１３年２月２５日　月曜日　午前１１時５３分

RQT9849

The speakers can be wall mounted by drilling screws into the wall, etc.

Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg.

The screws and other items are not supplied as the type and size will vary with each installation.

≥

For details about the required screws, refer to the diagram below the step “Drive a screw into the wall.”

16).

≥For a safety measure to prevent the speakers from falling, refer to page 23.

≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.

Assemble the centre speaker:

Attach the side caps and hook brackets to the speaker.

≥ There is no left and right for the centre speaker.

≥ Keep the screws out of reach of children to prevent swallowing.

Place the front speakers vertically

∏ 2 Front

speakers

∏ 1 Centre

speaker

∏ 3 Speaker cables

WHITE: Left

RED: Right

GREEN: Centre

∏ 2 Stand necks ∏ 2 Side caps ∏ 4 Screws

∏ 2 Hook

brackets

A Hook bracket (supplied) B Screw (supplied)

≥ Tighten securely.



SC-HTB770_RQT9849-B_mst.book 14 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Getting started

RQT9849

Assemble the centre speaker:

Connect the speaker cable.

≥ Insert the wire fully, taking care not to insert beyond the wire insulation.

Assemble the front speakers:

Attach the stand neck.

≥ The two front speakers are interchangeable.

≥ Keep the screws out of reach of children to prevent swallowing.

Assemble the front speakers:

Connect the speaker cables.

* If you have difficulty inserting the cable, try straightening the speaker cable and then bending the

cable about 20 mm from the tip, at an angle of approx. 45o (as illustrated above).

A Centre speaker

connector

1 Insert the wire fully.

r: White

s: Blue line

A Screw (supplied)

≥ Tighten securely.

1 Insert the wire fully.

r: White

s: Blue line

≥ Insert the wire fully,

taking care not to insert

beyond the wire

insulation.

2 Press into the groove.

Push

Green







Push

SC-HTB770_RQT9849-B_mst.book 15 ページ２０１３年２月２５日　月曜日　午前１１時５３分

RQT9849

Drive a screw into the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Leave at least 20 mm of space above and on each side of the speaker to allow enough space for fitting the speaker.

≥ Keep the screws out of reach of children to prevent swallowing.

Front speakers

At least 30 mm

B ‰4.0 mm

C ‰7.0 mm to

‰9.4 mm

D Wall or pillar

E 5.5 mm to 6.5 mm

F Front speaker

(Rear view)

G 100 mm

H 436 mm

I 34 mm

J Wall mounting hole

















 



Centre speaker

K At least 30 mm

L ‰4.0 mm

M ‰7.0 mm to

‰9.4 mm

N Wall or pillar

O 1.6 mm to 2.5 mm

P Max. 3.5 mm

Q Centre speaker

(Rear view)

R 18 mm

S 147 mm

T 13 mm

U 19.6 mm

V 50.2 mm























SC-HTB770_RQT9849-B_mst.book 16 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Getting started

RQT9849

Fit the speaker(s) securely onto the screw(s).

Red connector: The speaker attached to the red connector cable is to be placed on the right side.

White connector:The speaker attached to the white connector cable is to be placed on the left side.

A Left speaker connector B Right speaker connector

DO DO NOT

Front speaker Centre speaker

≥ Move the speaker so that the screw is in this

position.

≥ In this position, the speaker will likely fall if moved

to the left or right.





Red

White

SC-HTB770_RQT9849-B_mst.book 17 ページ２０１３年２月２５日　月曜日　午前１１時５３分

RQT9849

≥For a safety measure to prevent the speakers from falling, refer to page 23.

≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.

Assemble the speakers following steps 1 and 2 of “Place the speakers

horizontally” (> 11, 12).

Attach the leg stands.

≥ Keep the screws out of reach of children to prevent swallowing.

When placing the speakers on a table

Place the speakers using the leg stands

∏ 2 Front

Speakers

∏ 1 Centre speaker ∏ 3 Speaker cables

WHITE: Left

RED: Right

GREEN: Centre

∏ 1 Metal

bracket

∏ 2 Leg stands ∏ 6 Screws

Red connector:

With the speaker facing down, the speaker attached to the red connector cable is

to be placed on the left side.

White connector:

With the speaker facing down, the speaker attached to the white connector cable

is to be placed on the right side.

A Screw (supplied)

≥ Tighten securely.

B Screw hole

C Right speaker connector

D Left speaker connector









Align the higher or lower holes with the projecting parts on

the speaker.

≥ By changing the position that the stand is attached to the

projecting parts, the height can be adjusted by 9 mm.

White

Red

SC-HTB770_RQT9849-B_mst.book 18 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Getting started

RQT9849

≥For a safety measure to prevent the speakers from falling, refer to page 23.

≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.

Assemble the speakers following steps 1 and 2 of “Place the speakers

horizontally” (> 11, 12).

Attach the support legs and speaker feet.

≥ Keep the screws and the speaker feet out of reach of children to prevent swallowing.

Place the speakers using the support legs and

speaker feet

∏ 2 Front

Speakers

∏ 1 Centre speaker ∏ 3 Speaker cables

WHITE: Left

RED: Right

GREEN: Centre

∏ 1 Metal

bracket

∏ 2 Support legs ∏ 6 Screws

∏ 2 Speaker feet

Red connector:

With the speaker facing down, the speaker attached to the red connector cable is

to be placed on the left side.

White connector:

With the speaker facing down, the speaker attached to the white connector cable

is to be placed on the right side.

A Screw (supplied)

≥ Tighten securely.

B Screw hole

C Speaker foot (supplied)

D Right speaker connector

E Left speaker connector











Align the projecting

parts on the speaker

with support leg.

Red

White

SC-HTB770_RQT9849-B_mst.book 19 ページ２０１３年２月２５日　月曜日　午前１１時５３分

RQT9849

≥For a safety measure to prevent the speakers from falling, refer to page 23.

≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.

Assemble the centre speaker:

Attach the side caps and speaker feet to the speaker and connect the

speaker cable.

≥ There is no left and right for the centre speaker.

≥ Insert the wire fully, taking care not to insert beyond the wire insulation.

≥ Keep the screws and the speaker feet out of reach of children to prevent swallowing.

Place the front speakers using the speaker

bases

∏ 2 Front

Speakers

∏ 1 Centre speaker ∏ 3 Speaker cables

WHITE: Left

RED: Right

GREEN: Centre

∏

2 Stand necks

∏ 2 Speaker bases ∏ 2 Side caps

∏ 6 Screws ∏ 2 Speaker feet

Push

Green

A Screw (supplied)

≥ Tighten securely.

B Speaker foot (supplied)

C Centre speaker connector

1 Insert the wire fully.

r: White

s: Blue line

SC-HTB770_RQT9849-B_mst.book 20 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Page is loading ...

Panasonic SC-HTB770 Operating instructions

Brand: Panasonic

Model: SC-HTB770

Category: Speaker sets

Type: Operating instructions

Download PDF

report

Panasonic SC-HTB770 Operating instructions

Panasonic SC-HTB770 Operating instructions

Related papers

Other documents