Altusen KM0216 / KM0432 User manual

Matrix KVM Switch

KM0216 / KM0432

User Manual

www.altusen.com

KM0216 / KM0432 User Manual

ii

FCC Information

This is an FCC Class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take

adequate measures.

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

RoHS

This product is RoHS compliant.

KM0216 / KM0432 User Manual

iii

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed “as is.”

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

KM0216 / KM0432 User Manual

iv

Safety Instructions

General

 Read all of these instructions. Save them for future reference.

 Follow all warnings and instructions marked on the device.

 Do not place the device on any unstable surface (cart, stand, table, etc.). If

the device falls, serious damage will result.

 Do not use the device near water.

 Do not place the device near, or over, radiators or heat registers.

 The device cabinet is provided with slots and openings to allow for

adequate ventilation. To ensure reliable operation, and to protect against

overheating, these openings must never be blocked or covered.

 The device should never be placed on a soft surface (bed, sofa, rug, etc.) as

this will block its ventilation openings. Likewise, the device should not be

placed in a built in enclosure unless adequate ventilation has been

provided.

 Never spill liquid of any kind on the device.

 Unplug the device from the wall outlet before cleaning. Do not use liquid

or aerosol cleaners. Use a damp cloth for cleaning.

 The device should be operated from the type of power source indicated on

the marking label. If you are not sure of the type of power available,

consult your dealer or local power company.

 The device is equipped with a 3-wire grounding type plug. This is a safety

feature. If you are unable to insert the plug into the outlet, contact your

electrician to replace your obsolete outlet. Do not attempt to defeat the

purpose of the grounding-type plug. Always follow your local/national

wiring codes.

 Do not allow anything to rest on the power cord or cables. Route the

power cord and cables so that they cannot be stepped on or tripped over.

 If an extension cord is used with this device make sure that the total of the

ampere ratings of all products used on this cord does not exceed the

extension cord ampere rating. Make sure that the total of all products

plugged into the wall outlet does not exceed 15 amperes.

 To help protect your system from sudden, transient increases and

decreases in electrical power, use a surge suppressor, line conditioner, or

uninterruptible power supply (UPS).

KM0216 / KM0432 User Manual

v

 When connecting or disconnecting power to hot pluggable power supplies,

observe the following guidelines:

 Install the power supply before connecting the power cable to the power

supply.

 Unplug the power cable before removing the power supply.

 If the system has multiple sources of power, disconnect power from the

system by unplugging all power cables from the power supplies.

 Never push objects of any kind into or through cabinet slots. They may

touch dangerous voltage points or short out parts resulting in a risk of fire

or electrical shock.

 Do not attempt to service the device yourself. Refer all servicing to

qualified service personnel.

 If the following conditions occur, unplug the device from the wall outlet

and bring it to qualified service personnel for repair.

 The power cord or plug has become damaged or frayed.

 Liquid has been spilled into the device.

 The device has been exposed to rain or water.

 The device has been dropped, or the cabinet has been damaged.

 The device exhibits a distinct change in performance, indicating a need

for service.

 The device does not operate normally when the operating instructions

are followed.

 Only adjust those controls that are covered in the operating instructions.

Improper adjustment of other controls may result in damage that will

require extensive work by a qualified technician to repair.

KM0216 / KM0432 User Manual

vi

Rack Mounting

 Before working on the rack, make sure that the stabilizers are secured to

the rack, extended to the floor, and that the full weight of the rack rests on

the floor. Install front and side stabilizers on a single rack or front

stabilizers for joined multiple racks before working on the rack.

 Always load the rack from the bottom up, and load the heaviest item in the

rack first.

 Make sure that the rack is level and stable before extending a device from

the rack.

 Use caution when pressing the device rail release latches and sliding a

device into or out of a rack; the slide rails can pinch your fingers.

 After a device is inserted into the rack, carefully extend the rail into a

locking position, and then slide the device into the rack.

 Do not overload the AC supply branch circuit that provides power to the

rack. The total rack load should not exceed 80 percent of the branch circuit

rating.

 Ensure that proper airflow is provided to devices in the rack.

 Do not step on or stand on any device when servicing other devices in a

rack.

KM0216 / KM0432 User Manual

vii

Package Contents

The KM0216 / KM0432 package consists of:

1 KM0216 or KM0432 Matrix KVM Switch

1Power Cord

1 Rack Mount Kit (brackets and Phillips head hex M3 x 8 screws)

1 Foot Pad Set (4 pcs.)

1 User Manual*

1 Quick Start Guide

1 Registration Card

Check to make sure that all of the components are present and in good order.

If anything is missing, or was damaged in shipping, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the switch or to any other

devices on the KM0216 / KM0432 installation.

* Changes may have been made to the manual since it was printed. Please

visit our Website to check for the most up-to-date version.

®

International Co., Ltd.

Manual Part No.: PAPE-0213-3AXG

Printing Date: 08/2006

All other brand names and trademarks are the registered property of their respective owners.

KM0216 / KM0432 User Manual

viii

Contents

FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

ALTUSEN Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiii

Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiii

Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiii

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiv

Chapter 1.

Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Benefits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

KM0216 / KM0432 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

KM0216 / KM0432 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Chapter 2.

Installation

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Before you Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Stacking and Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Rack Mounting—Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Rack Mounting—Rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Single Stage Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Multilevel Installations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Daisy Chaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Cascading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Daisy Chaining Plus Cascading Expansion . . . . . . . . . . . . . . . . . . . . 24

Topology Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Basic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

KM0216 / KM0432 User Manual

ix

Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Switching Station Positions:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Hot Plugging Console Ports: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Powering Off and Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Port ID Numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Single Stage and Daisy Chained Installations: . . . . . . . . . . . . . . .28

Cascaded Installations: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

User Management and Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Chapter 3.

OSD Operation

OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

F1 GOTO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

F2 LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

F3 SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

F4 ADM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

F5 SKP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

F6 BRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

F7 SCAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

F8 LOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Chapter 4.

Hotkey Operation

Hotkey Port Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Invoking Hotkey Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Selecting the Active Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Auto Scanning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Setting the Scan Interval:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Invoking Auto Scan:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Skip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Hotkey Beeper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Hotkey Summary Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Chapter 5.

Keyboard Emulation

Mac Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Sun Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Chapter 6.

The Firmware Upgrade Utility

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

KM0216 / KM0432 User Manual

x

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Performing the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Starting the Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Appendix

Computer Connection Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

KM0216 Daisy Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

KM0216 Cascade to KH88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

KM0432 Daisy Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

KM0432 Cascade to KH88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

OSD Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Supported KVM Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Additional Installation Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Clear Login Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Sun Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Index

KM0216 / KM0432 User Manual

xi

About This Manual

This User Manual is provided to help you get the most from your KM0216 /

KM0432 system. It covers all aspects of installation, configuration and

operation. An overview of the information found in the manual is provided

below.

Overview

Chapter 1, Introduction, introduces you to the KM0216 / KM0432 system.

Its purpose, features and benefits are presented, and its front and back panel

components are described.

Chapter 2, Installation, provides step-by-step instructions for setting up

your installation, and explains some basic operating procedures.

Chapter 3, OSD Operation, provides detailed information for configuring

and controlling your installation using the KM0216 / KM0432’s intuitive,

mouse-driven On Screen Display (OSD) menus.

Chapter 4, Hotkey Operation, explains the concepts and procedures used

to control the KM0216 / KM0432 from the keyboard.

Chapter 5, Keyboard Emulation, lists the keys for a PC-compatible

keyboard to emulate the functions of the Mac and Sun keyboards.

Chapter 6, The Firmware Upgrade Utility, explains how to upgrade the

KM0216 / KM0432’s flash firmware version.

An Appendix at the end of the manual provides technical and

troubleshooting information.

KM0216 / KM0432 User Manual

xii

Conventions

This manual uses the following conventions:

Monospaced Indicates text that you should key in.

[ ]

Indicates keys you should press. For example, [Enter] means

to press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1.

Numbered lists represent procedures with sequential steps.

♦

Bullet lists provide information, but do not involve sequential

steps.

→

Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

→ Run means

to open the Start menu, and then select Run.

Indicates critical information.

KM0216 / KM0432 User Manual

xiii

ALTUSEN Information

Technical Support

Getting Help

For additional help, advice, and information, ALTUSEN provides several

support options. If you need to contact ALTUSEN technical support with a

problem, please have the following information ready beforehand:

 Product model number, serial number, and date of purchase

 Your computer configuration, including operating system, revision level,

expansion cards, and software

 Any error messages displayed at the time the error occurred

 The sequence of operations that led up to the error

 Any other information you feel may be of help

North America Technical

Phone Support

Registered ALTUSEN product owners are entitled to

telephone technical support. Call the ALTUSEN

Technical Support Center: 949-453-8885.

International Technical

Phone Support

Contact your local dealer.

Call the ALTUSEN Technical Support Center:(886-2)

8692-6959.

Email Support E-mail your questions and concerns to:

[email protected]

Online Support

Troubleshooting

Documentation

Software Updates

Online troubleshooting that describes the most

commonly encountered problems and offers

possible solutions to them; online documentation

(including electronically available manuals); and the

latest drivers and firmware for your product are

available at the ALTUSEN Website: http://

www.altusen.com

KM0216 / KM0432 User Manual

xiv

Product Information

For information about all of ALTUSEN's products and how they can help you

connect without limits, visit ALTUSEN on the Web or contact an ALTUSEN

Authorized Reseller.

 In the United States of America, call: 866-ALTUSEN (866-258-8736)

 In Canada and South America, call: 949-453-8885

 In all other locations, call: 886-2-8692-6789

 Visit ALTUSEN on the Web at http://www.altusen.com for a list of

locations and telephone numbers

1

Chapter 1

Introduction

Overview

The KM0216 / KM0432 Matrix KVM Switch gives IT administrators in large

corporations advanced control of multiple servers. Operators working at up to

two (KM0216) or four (KM0432) consoles (keyboard, mouse, and monitor)

can simultaneously and independently take direct control of up to 16

(KM0216) or 32 (KM0432) computers. With a combination of daisy chaining

and cascading, up to 16 or 32 operators can access and control up to 1,024 or

2,048 computers.

The 2 / 4 consoles belonging to the master unit (the highest level KM0216 /

KM0432) are able to access all the computers on the installation—those that

are directly connected as well as those that are daisy chained and cascaded. The

2 / 4 consoles belonging to each of the Slave units (the daisy chained KM0216

/ KM0432s), however, can only access the computers that are connected to

them on the same daisy chain level (directly connected and cascaded).

The KM0216 / KM0432 features a console module design with automatic

console conversion that allows any combination of PS/2 and USB consoles to

control any combination of PS/2, USB, or Sun computers. The RJ-45 port

connectors, combined with Auto Signal Compensation (ASC), allow signals to

travel up to 500 feet (150 meters) away and still maintain high video resolution;

eliminating the need for KVM extenders, and allowing the installation to take

advantage of the internal Cat 5e and Cat 6 wiring built in to most modern

commercial buildings. In addition, use of RJ-45 connectors saves precious IT

real estate by allowing a full 16 or 32 KVM ports to reside in a single 1U

system case.

Setup is fast and easy; plugging cables into their appropriate ports is all that is

entailed. Because the KM0216 / KM0432 intercepts keyboard and mouse input

directly, there is no software to configure, so there is no need to get involved

in complex installation routines or be concerned with incompatibility

problems.

Access to any computer is easily accomplished either by means of a powerful

menu driven OSD (On Screen Display) system, or by entering Hotkey

combinations from the keyboard. A convenient Auto Scan feature also permits

automatic scanning and monitoring of the activities of all computers running

on the installation one by one.

KM0216 / KM0432 User Manual

2

Features

 Two or four consoles independently and simultaneously control up to 16

or 32 directly connected computers

 Daisy chain up to 7 additional units

 Cascade up to 16 or 32 compatible KVM switches from each station on the

chain

 Up to 16 or 32 consoles control all of the computers on a daisy chained/

cascaded installation

 Compact design—RJ-45 connectors allow rack mounting in a 19", 1U,

system rack

 Multiplatform support: PC, Mac and Sun

 Console conversion—any type of console can control any type of

computer—mixed combinations (PS/2 & USB) supported on both the

console and computer sides

 PS/2 keyboard and mouse emulation—computers boot even when the

console focus is elsewhere

 Hot pluggable—add or remove components without having to power off

the switch

 No software required—convenient computer selection via intuitive hotkey

combinations or On Screen Display (OSD) menus

 OSD port list automatically expands when stations are added—port names

are automatically reconfigured when the station sequence is changed

 OSD screen automatically adjusts to resolution changes

 Auto Scan feature for monitoring user-selected computers

 Three level password security: Super Administrator, Administrator, and

Users

 LCD, VGA, SVGA, XGA, and MultiSync support; DDC2B

 Superior video quality—1024 x 768 @ 60Hz for up to 150m; 1920 x 1440

@ 60Hz (distance depends on installation environment)

 Auto Signal Compensation (ASC) assures optimum video resolution for

distances up to 150m between the switch and the consoles or computers—

no DIP switch setting required

 Lifetime firmware upgrading via flash ROM

Chapter 1. Introduction

3

Benefits

The KM0216 / KM0432 Matrix KVM Switch saves time and money by

allowing a single console to manage each of the connected computers. A

KM0216 / KM0432 installation provides the following benefits:

 Eliminates the cost of a keyboard, monitor, and mouse for each computer.

 Eliminates the need for the additional space of the extra components.

 Saves on energy costs.

 Eliminates the inconvenience, time and effort required to move from one

computer to another.

 Allows centralized control of computers located at non-contiguous

locations on the site.

KM0216 / KM0432 User Manual

4

System Requirements

Console

The following hardware components are required for each console:

 A VGA, SVGA, or MultiSync monitor capable of displaying the highest

resolution provided by any computer in the installation

 Keyboard and mouse (PS/2 or USB)

Console modules are required to connect consoles to the KM0216 / KM0432.

They provide flexibility for your installation by allowing PS/2 and USB

interfaces to be mixed and matched at the console side. The console modules

currently available are listed in the table below. Contact your dealer for details

or refer to the documentation included with your console module.

Computers

The following hardware components are required for each computer:

 A VGA, SVGA, or MultiSync video graphics card with an HDB-15 port;

or, for legacy Sun systems, a Sun 13W3 video port

 PS/2 keyboard and mouse ports (6-pin Mini-DIN); or, at least one USB

port; or, for legacy Sun systems, a Sun style keyboard port (8-pin Mini-

DIN)

KVM adapter cables (CPU modules) are required to connect computers to the

KM0216 / KM0432. Similar to console modules, they allow PS/2, USB, Sun,

Mac, and serial computers to be attached to the KM0216 / KM0432. The KVM

adapter cables currently available are listed in the table below. Contact your

dealer for details.

Function Model Number

PS/2 Console Module KA9222

USB Console Module KA9272

Function Model Number

KVM Adapter

Cable

(CPU Module)

For PS/2 computers KA9120

For Sun Legacy computers KA9130

For Sun USB computers KA9131

For serial devices KA9140

For USB computers KA9170

Chapter 1. Introduction

5

Cables

One or more of the following cables are required for use with the KM0216 /

KM0432:

Operating Systems

 Microsoft

®

Windows

®

95, 98, 98SE, ME, NT, 2000, XP or later

 Mac OS

®

8.6, 9.0, 9.1, X, 10.1, 10.2, 10.3 or later

 RED HAT

®

Linux

®

6.0, 7.1, 7.2, 7.3, 8.0 or later

 Mandrake Linux 9.0 or later

 SUSE 8.2 or later

 Free BSD 3.5.1, 4.2, 4.3, 4.5 or later

 Sun Solaris™ 8 or later

 Netware 5.0, 6.0 or later

 OS/2 Ver 2.0

 AIX 4.3 or later

 DOS 6.22

Function Type

Console Module or KVM Adapter Cable to

KM0216 / KM0432 (see page 67)

Cat 5 cable

Daisy Chain Cables LIN5-50H1-H12 (15 cm)

2L-1700KM (60 cm)

2L-1701KM (1.2 m)

2L-1704KM (4 m)

KM0216 / KM0432 User Manual

6

KM0216 / KM0432 Front View

KM0216

KM0432

12 3

45

12 3

45

Page is loading ...

Altusen KM0216 / KM0432, KM0432 User manual

Related papers

Other documents