11
213 3 4 5 6 7 8 9 101
12
Service hotline
In the case of technical problems, contact our Service hotline. Switzerland:
Tel. 0900 00 1675 (national charges, Swisscom at time of going to print:
CHF2.60/min).Inthecaseofclaimsunderthetermsofguarantee,contact
your sales outlet.
Maintenance
Cleanthesurfaceofthehousingwithasoft,uff-freecloth.Donotuseany
cleaning agents or solvents.
Guarantee
SWITEL equipment is produced and tested according to the latest produc-
tion methods. The implementation of carefully chosen materials and highly
developed technologies ensure trouble-free functioning and a long service
life. The terms of guarantee do not apply when a device malfunction was
causedbythemobiletelecommunicationsnetworkoperator/provider.The
terms of guarantee do not apply to the batteries or power packs used in the
products. The period of guarantee is 24 months from the date of purchase.
Alldecienciesrelatedtomaterialormanufacturingerrorswithintheperiod
ofguaranteewillberedressedfreeofcharge.Rightstoclaimsunderthe
terms of guarantee are annulled following tampering by the purchaser
or third parties. Damage caused as the result of improper handling or
operation, normal wear and tear, incorrect positioning or storage, improper
connectionorinstallationorActsofGodandotherexternalinuences
are excluded from the terms of guarantee. In the case of complaints, we
reserve the right to repair defective parts, replace them or replace the
entiredevice.Replacedpartsordevicesbecomeourproperty.Rights
to compensation in the case of damage are excluded where there is no
evidence of intent or gross negligence by the manufacturer. If your device
does show signs of a defect within the period of guarantee, please contact
the sales outlet where you purchased the SWITEL device, producing the
purchase receipt as evidence. All claims under the terms of guarantee in
accordance with this agreement can only be asserted at the sales outlet.
No claims under the terms of guarantee can be asserted after a period of
two years from the date of purchase and hand-over of the product.
Disposal
In order to dispose of your device, take it to a collection point
provided by your local public waste authorities (e.g. recycling
centre).Accordingtothelawsonthedisposalofelectronicand
electrical devices, owners are obliged to dispose of old electronic
and electrical devices in a separate waste container. The adjacent
symbol indicates that the device must not be disposed of in normal
domestic waste!
You are legally obliged to dispose of power packs and batteries
at the point of sale or in the corresponding containers provided at
collection points by local public waste authorities. Disposal is free of
charge. The symbols indicate that the batteries must not be disposed
of in normal domestic waste and that they must be brought to collection
points provided by local public waste authorities. Packaging materials must
be disposed of according to local regulations.
Declaration of Conformity
ThisdevicefullstherequirementsstipulatedintheDirective
1999/5/EConradioequipmentandtelecommunicationsterminal
equipmentandthemutualrecognitionoftheirconformity.Conformi-
tywiththeabovementioneddirectiveisconrmedbytheCEmarkonthe
device.ToviewthecompleteDeclarationofConformity,pleaserefertothe
free download available on our web site www.switel.com.
Wireless video monitoring system HS 1000
OVERVIEW
a Conguremotiondetection,brightness,andpairadditionalcamerasto
the monitor.
b Congurerecordingsettingssuchasdatestamps,recordingle
size,leoverwriteandmore.
c Set schedules to have the system record continuously or just
motion-eventsduringspecictimeseachday
d Conguresystemtime,date&timeformat,powersavingmode,or
restore default system settings.
e View and manage saved images and videos.
f Enable/disablealarmbuzzerformotion-detectionevents.
g View live video.
h Displays the size of the inserted microSD card.
USING THE MAIN MENU
Press to enter the menu.
Usethe▲▼◄►keystomakeaselection.
Press OKtoconrmaselection.
Press to exit or return to the previous menu.
SETTING THE DATE & TIME
NOTE: It is important to set the date and time to ensure that they are
properly captured on recordings.
Press to enter the main menu.
Select (d)usingthearrowkeys,thenpressOK.
Select Clock setup, then press OK.
Press◄/►tocongurethecurrentdateandtime.Press▲/▼to
move between items.
Whennished,pressOK to save your settings.
Press to exit or return to the previous menu.
PAIR AN ADDITIONAL CAMERA
Connectthenewcameratoapoweroutlet.Placethecameraandthe
monitor within 1ft of each other.
Press then select the Camera Setting icon. Press OKtoconrm.
Select Pairing and press OK.
Use the arrow keys on the receiver to select the channel you want to
pairthecamerato.Channelsthatarepairedtoanexistingcamera
show the statement PAIR OK, while open channels show NO PAIR.
Press OK on the desired channel to begin pairing.
If you pair a new camera to a channel that is already being used by an
existing camera, the new camera will be connected to that channel. The
old camera will automatically be disconnected.
Following the onscreen prompt (the selected channel shows the
statement PAIRING),pressthePairbuttonbehindthecamera.You
have 30 seconds to press the Pair button on the camera. If pairing was
successful, the pairing channel shows the statement PAIR OK.
Do not press and hold the Pair button!
Press until you have exited all menus. You can now view live video
from the camera by selecting the channel using the arrow keys on the
monitor.
Other settings in the menu similar to this example!
CAMERA SETUP
Before installing camera, carefully plan where and how it will be po-
sitioned, and where you will route the cable that connects the camera
to the power adapter
Camerasareratedforindoor/outdoorinstallation,butarenotintended
for direct exposure to rain or snow. For outdoor applications install
under shelter protected from the elements.
Wireless cameras require a power source to operate.
Ensure power outlets are sheltered from the elements.
Use the included mounting screws to attach the camera stand to the
mounting surface
Mark the positions of the screw holes on the mounting surface with the
base of the mounting stand.
Drillholesandinsertthedrywallanchors(included)asneeded.
Firmly attach camera to the surface using the included screws.
If you run the power cable through the mounting surface, connect
power before attaching the camera to the wall.
Attach the camera stand to the camera.
Loosen the adjustment ring on the metal
camera stand and move the camera to the
desired position.
Tightentheadjustmentringwhennished,
holdingthecamerarmlyinposition.
Connectoneendofthecamera’spoweradaptertothecameraandthe
other end to an electrical outlet or surge protector. Make sure the power
connector is fully inserted to avoid water getting in the plug.
Removetheprotectivelmfromthefrontofthecamera.Ifthelmis
not removed, it will affect picture quality.
LCD MONITOR SETUP
Use a Phillips screwdriver
(notincluded)toopenthebattery
compartment on the back panel.
Insert the included battery so the
statement “THIS SIDE UP“ is
visible, and the clear plastic tabs
on the side of the battery face
outwards.Replacethebattery
compartment cover
Connecttheincludedpoweradaptertothemonitorandtoanelectrical
outlet.
Makesuretorstconnectthecameratoanelectricaloutletbefore
powering on the receiver. This will ensure a proper connection.
Chargethereceiverovernightbeforeusing.Thereceiver’s
rechargeable battery provides up to 5 hours of portable use.
PulluptheantennaonthebackoftheLCDmonitor.
Press and hold the power button on the front panel for 2 seconds. The
startup screen appears, followed by live video from your camera.
MAIN MENU
Feature Value
HS 1000 Operating range: Outdoor max. 150 m, indoor max. 50 m
WxHxD(camera) 138x232x78mm
WxHxD(monitor) 188x17x132mm
Weight(camera) 340g(withoutstand)
Weight(monitor) 340 g
Frequency 2,400~2,4835GHz
Image MPEG4
OperatingTemperature(Camera) 14~122°F/–10~50°C
Camerasensor 1/4“CMOS
Monitordisplay 7“(17,8cm)ColorLCD(800x480pxl)
Technical data(Allrightsreserved)
Power adaptor plug
Usingtheenergy-efcientpoweradaptormodelforcamera(6VDC800mA
±5%)andmonitor(5VDC2000mA±5%)
ATTENTION!
WARNING!
ENGLISH
Operating Instructions
Please read and observe the following information and keep the
operating manual nearby for future reference!
Safety information
Riskofexplosion!
Only use the power adapter plugs supplied!
Only use batteries supplied or ones of the same type!
Always treat batteries with due care and attention and only use
batteries as described.
Never use standard and rechargeable batteries together. Never use
rechargeable batteries or standard batteries with different capacities or
charge statuses together. Never use standard or rechargeable batteries
which are damaged. Never charge the batteries.
Riskofsuffocationthroughsmallobjects,packagingandprotectivefoil!
Keep children away from the product and its packaging!
Riskstohealthandtheenvironmentfrombatteries!
Never open, damage or swallow batteries or allow them to pollute the
environment. They could contain toxic and ecologically harmful heavy
metals.
Never use the units in the vicinity of medical equipment. Effects on
such equipment cannot be fully ruled out. Please observe a minimal
distance of 2.5m to sources of interference such as televisions or
computer screens.
Riskofrethroughpoweradapterplugs!Poweradapterplugscanheat
up. Never leave any objects on the power adapter plugs. Ensure
access to power adapter plugs is not obstructed by furniture or such.
Riskoftrippingduetoimproperlylaidcable!Laythecablessothat
nobody can trip over them!
Preventexposuretoenvironmentalinuences,e.g.smoke,dust,
vibration, chemicals, moisture, heat and direct sunlight.
Onlyallowrepairstobecompletedbyqualiedpersonnel.
Removethepoweradapterandbatteryduringlongperiodofnon-use.
PACKAGE CONTENTS
1Camera,1Monitor,2Poweradapterplug, 1 Operating instruction
1Rechargeablebattery,1Camerastand,1Mountingkit
Monitor
Camera
INTENDED USE
The camera serves a video stream to the monitor. Any other use is
consideredunintendeduse.Unauthorisedmodicationorreconstructionis
not permitted. Under no circumstances open the devices or complete any
repair work yourself. Observe all local directives and regulations.
NOTE: Avoid installing in a location that requires the wireless signal to
pass through cement, concrete, or metal structures. This will reduce the
transmission range.
OPERATING ELEMENTS
1 Press and hold for 2 seconds to turn the receiver on or off.
2 Press to enter the system menu.
3 Inmenus,presstoconrmaselection.Play/Pause:Duringvideo
playback,presstoplay/pausevideo.
4 During live view, press repeatedly to change the view to a different
channel or to see all channels in quad or sequence mode.
In menus, press to move menu selection to the left.
During video playback, press and hold to rewind video.
5 During live view, press repeatedly to change the view to a different
channel or to see all channels in quad or sequence mode.
In menus, press to move menu selection to the right.
During video playback, press and hold to fast-forward video.
6 In menus, press to move menu selection down. During live view and
playback, press to decrease the volum of the receiver.
7 In menus, press to move menu selection up. During live view and
playback, press to increase the volume of the receiver.
8 Inmenus,presstoreturntothepreviousmenu.Duringvideo
playback, press to stop video.
9 During live view, press to save an image of the video display.
During live view, press and hold to begin recording video.
Presswhileanimageorvideoleisselectedtodeletethele.
10 During live viewing, press to zoom in. Press again to zoom out.
11 Display
12 Antenna
13 Camerastand
14 Screw
15 Battery compartment
16 Battery
14
15
16
e f g h
a b c d