Panasonic EY 6813 Owner's manual

Page is loading ...

-

4

-

Read “Safety Instructions” booklet and

the following before using.

. ADDITIONAL

SAFETY RULES

1) Use auxiliary handle (support han-

dle) supplied with the tool. Loss of

control can cause personal injury.

2) Be aware that this tool is always in

an operating condition, since it does

not have to be plugged into an elec-

trical outlet.

3) When drilling into walls, floors, etc.,

“live” electrial wires may be en-

countered. DO NOT TOUCH THE

CHUCK OR ANY FRONT METAL

PARTS OF THE TOOL! Hold the

tool only by the plastic handle to

prevent electric shock in case you

drill into a “live” wire.

4) If the bit becomes jammed, immedi-

ately turn the main switch off to pre-

vent an overload which can dam-

age the battery pack or motor. Use

reverse motion to loosen jammed

bits.

5)

Do NOT operate the Forward/Reverse

lever when the main switch is on. The

battery will discharge rapidly and dam-

age to the unit may occur.

6) Use only a dry, soft cloth for wiping

the unit. Do not use a damp cloth,

thinner, benzine, or other volatile

solvents for cleaning.

7)

When storing or carrying the tool, set

the Forward/Reverse lever to the cent-

er position (switch lock).

8) Do not strain the tool by holding

the speed control trigger halfway

(speed control mode) so that the

motor stops. The protection circuit

will activate and may prevent speed

control operation. If this happens,

release the speed control trigger

and squeeze again for normal oper-

ation.

9) Be careful not to get dust inside the

chuck.

10) Do not touch the rotating parts to

avoid injury.

11) Do not continue to use the tool for a

long time. Stop using the tool from

time to time to avoid that the tem-

perature of the motor rises too high.

12) Do not drop the tool.

13) Wear ear protectors when using the

tool for extended periods.

Symbol meaning

V Volts

Direct current

n

0

No load speed

…/min

Revolutions or reciproca-

tion per minutes

Forward rotation

Reverse rotation

Rotation with hammering

Rotation only

-

5

-

. OPERATION

Chuck

...

(A)

NOTE: Grease for bit

Grease the oval indentation

on the bit with the supplied

grease at least once a month.

1. To mount the bit

1-1. Insert a bit into the mounting hole,

and turn it slightly to locate an en-

gaged position.

1-2. At the engaged position, push the

bit as far as it goes. Make sure that

the bit is fixed by pulling it.

SDS PLUS type

shank

2. To dismount the bit

2-1. Depress the chuck cover and pull

the bit.

Foward/Reverse lever

...

(E)

ReverseForward

Be sure to set the switch in the cent-

er to lock it after use.

Operate the Forward/Reverse lever

after the motor rotation is completely

stopped.

Hammering/drilling switching

lever

...

(C)

Speed/Blow Mode selection

lever

...

(D)

1. There are four modes available with

the combination of Hammering/ drill-

ing switching lever and Speed/Blow

Mode selection lever.

Select the suitable mode for appli-

cation.

2. Operate the mode change after

the motor rotation is completely

stopped.

Position of

switching

lever

Speed/Blow Mode

selection lever

Recommended

application

(

Rotation with

hammering

)

Hard blow hammer-

ing mode

This mode has hard

blow hammering which

is suitable for concrete

drilling.

Concrete drill

Soft blow hammering

mode

This mode is suitable

for concrete drilling

with smaller diameter

drill, or for drilling into

soft base material.

Small diameter

concrete drill

(

Rotation only

)

High speed drilling mode

This mode is suitable

for metal drilling with

high speed rotation.

Metal drill

Metal hole saw

Slow speed drilling mode

This mode is suitable

for wood drill with high

torque.

Wood drill

Variable speed control trigger

...

(F)

To set the center of a hole, pull the trigger

slightly to start the drill rotation slowly.

-

6

-

Support handle

...

(I)

Place the support handle at your fa-

vorite position and tighten the handle

securely.

Loosen Tighten

Depth gauge

...

(B)

Loosen the support handle and ad-

just the depth gauge at your favorite

depth.

After adjusting, tighten the support

handle and fix depth gauge.

Depth gauge

Depth of drilling

Battery pack

...

(H)

For Appropriate use of Battery Pack

·Ni-MH Battery pack EY9210

Charge the battery pack fully before

storage in order to ensure a longer

service life.

·Ni-Cd Battery pack EY9116

Discharge the battery pack empty be-

fore storage in order to ensure a long-

er service life.

The ambient temperature range is be-

tween 0°C (32°F) and 40°C (104°F).

If the battery pack is used when the

battery temperature is below 0°C

(32°F), the tool may fail to function

properly. In that case, charge the bat-

tery until charging is completed for

appropriate functioning of the battery.

Battery pack life

The rechargeable batteries have a lim-

ited life. If operation time becomes ex-

tremely short after recharging, replace

the battery pack with a new one.

NOTE:

Use under extremely hot or

cold conditions will reduce op-

erating capacity per charge.

Battery Recycling

For environmental protection and re-

cycling of materials, be sure that it is

disposed of at an officially assigned lo-

cation, if there is one in your country.

ATTENTION:

Ni-Cd Battery pack EY9116

This appliance contains Nickel-

Cadmium. Battery must be recy-

cled or disposed of properly.

Release lever

...

(G)

Battery pack Installation and Re-

moval

-For removal-

Pull the release lever to free the bat-

tery holder.

Battery holder

Release

lever

-For installation-

Fit the battery holder unit it clicks in

position.

Battery charger

...

(J)

NOTE: Charge a new battery pack,

or a battery pack that has not

been used for a prolonged time,

for about 24 hours to bring the

battery up to full charge.

-

7

-

1. Plug the charger into an AC outlet.

2. Insert the battery pack firmly into

the charger.

To AC

outlet

Battery

pack

Battery

charger

Battry pack

To AC

outlet

Battery

charger

3. During charging, the charging lamp

will light up.

When the charge is completed, an

internal electronic switch will auto-

matically be triggered to prevent

overcharging.

Charging will not occur if the bat-

tery pack is warm (for example,

immediately after heavy-duty op-

eration). The orange standby

lamp will light up until the battery

becomes cool. Charging will then

begin automatically.

4. When charging is completed, the

charging lamp will start flashing

quickly.

5. When the battery pack has not

been used for a long time, the

charging lamp starts flashing slow-

ly to indicate protective charging.

Protective charging takes longer to

fully charge the battery pack, than

the standard charging time. (Max.

charging time is approx. 90min-

utes.)

If a fully charged battery pack is in-

serted into the charger again, the

charging lamp may light up. Af-

ter several minutes, the charging

lamp may flash quickly to indicate

the charging is completed.

6. If the charging lamp does not light

immediately after the charger is

plugged in, or if after the standard

charging time the lamp does not go

off, consult an authorized dealer.

NOTE: When a cold battery (of about

5°C (41°F) or less) is to be

charged in a warm room,

leave the battery in the room

for at least one hour and

charge it when it has warmed

up to room temperature.

(Failing to do so may result in

less than a full charge.)

Cool down the charger when

charging more than two bat-

terypacks consecutively.

Do not insert your fingers in-

to contact hole, when hold-

ing charger or any other oc-

casions.

CAUTION: Do not use power

source from an engine

generator.

Do not cover vent holes

on the charger and the

battery pack.

Unplug the charger when

not in use.

-

8

-

LAMP INDICATIONS

EY0214 : EY6813NQKW

Flashing

Lit

Flashing quickly

Lit

Flashing

Charger is plugged into a wall outlet.

Ready to charge.

Now charging

Charging is completed.

Battery pack is warm. Charging will begin

when temperature of battery pack drops.

Charging is not possible. Clogged with

dust or malfunction of the battery pack.

Protective charging

Flashing slowly

EY0110 : EY6813FQW

Red Flashing

Red Lit

Green Flashing quickly

Orange Lit

Orange Flashing

Charger is plugged into the AC outlet.

Ready to charge.

Now charging

Charging is completed.

Battery pack is warm. Charging will begin

when temperature of battery pack drops.

Charging is not possible. Clogged with

dust or malfunction of the battery pack.

-

9

-

Dust Collection Cup (EY9X004)

...

(L)

* Drill bits of which diameter is 20 mm

above cannot be inserted through

dust collection cup.

* Do not use the tool for cutting other

than concrete, mortar and other ceram-

ic materials. If used for cutting metal

materials, the dust collection cup may

be damaged by the metal chip heat.

1. Install a dril bit.

2. Pass the drill bit through A and fix

the cup at B by matching with the

shape of the support handle.

A

B

Operation

Keep the dust collection cup in close

contact with the wall surface during

operation.

Removal

Hold the base of the dust collection

cup for removal.

Please remove after thoroughly get-

ting rid of the dust in the dust collec-

tion cup.

Base

Storage

Do not store the dust collection cup

in a compressed position. If kept in a

compessed position, it may be impos-

sible to return to the original shape.

. MAINTENANCE

Use only a dry, soft cloth for wiping

the unit. Do not use a damp cloth,

thinner, benzine, or other volatile sol-

vents for cleaning.

. ACCESSORIES

Optional

attachment

Can be used in:

Hammer-

ing mode

Drillring

mode

Drill chuck

EY9HX400E

No Yes

dia.1.5mm 13mm (1/16

1/2 )

Wood drill

Metal drill

Don't in hammering mode.

Hammer chuck

EY9HX401E

Yes Yes

dia.2.5mm 13mm (3/32

1/2 )

Masonry drill bit with

straight shank

(for bricks, mortar, cinder

block, Aired Light Concrete

drilling only)

Wood drill

Metalwork drill

Chiseling

attachment

EY9HX402E

Yes No

Light weight chiseling.

Peeling off tiles

Making ditch for plumbing

Basement trimming

-

10

-

. USAGE SUGGESTION

1. If there isn’t enough force pushing down on the bit, the hammer may not be able

to blow in hammering mode.

This is to prevent the hammering mode from operating with no load. Press down

harder on the bit to engage the hammer and cause it to blow.

Always be sure to press down with enough force when working.

2. In winter or in other situations where the temperature of the unit is low (5°C or be-

low), the blow of the hammering mode may be weaker than normal at the begin-

ning stage.

This is because the grease becomes stiffer in low temperatures, increasing fric-

tion.

If this should happen, operating hammering mode with no load for approximately

30 seconds and repeat this 3 times. This will restore its blowing power.

. SPECIFICATIONS

Main Unit (EY6813)

Maximum Drilling Diameter

Concrete

20mm (25/32 )

Steel

13mm (33/64 )

Wood

27mm (1-1/16 )

Motor Voltage DC Motor 24V

Speed At No Load (RPM)

Slow Mode 0 520 /min (rpm)

High Mode 0 950 /min (rpm)

Blows Rate Per Minute (BPM)

Soft Mode 0 3100 /min (bpm)

Hard Mode 0 4600 /min (bpm)

Weight (with battery pack) 4.35 kg

(9.6 lbs) EY6813NQKW / 4.2 kg

(9.3 lbs) EY6813FQW

Dimensions (L×W×H)

316×206×74 mm

(12

-

28/64 ×8

-

7/64 ×2

-

58/64 )

Battery Pack

Battery included

EY9210 :

(EY6813NQKW)

Ni-MH Battery

EY9116 :

(EY6813FQW)

Ni-Cd Battery

Voltage 24 V DC (1.2 V × 20 cells)

-

11

-

Battery Charger

Model EY0214 : EY6813NQKW

Electrical rating See the rating plate on the bottom of the charger.

Weight 0.97 kg

,

(2.14 lbs.)

Charging time

7.2V 9.6 V 12V 15.6V 18V 24V

1.2Ah

EY9065

EY9066

EY9080

EY9086

EY9001

EY9006

20min.

1.7Ah

EY9180

EY9182

EY9101

25min.

2.0Ah

EY9168

EY9106

EY9107

EY9136

EY9116

EY9117

30min. 30min. 30min.

3.0Ah

EY9200 EY9230 EY9210

45min. 45min.

3.5Ah

EY9201 EY9231

55min.

Model EY0110 : EY6813FQW

Electrical rating See the rating plate on the bottom of the charger.

Weight 0.78 kg

,

(1.72 lbs.)

Charging time

7.2V 9.6 V 12V 15.6V 18V 24V

1.2Ah

EY9065

EY9066

EY9080

EY9086

EY9001

EY9006

20min.

1.7Ah

EY9180

EY9182

EY9101

25min.

2.0Ah

EY9168 EY9106 EY9136

EY9116

EY9117

30min. 30min. 60min.

3.0Ah

EY9200 EY9230 EY9210

45min. 90min.

3.5Ah

EY9201 EY9231 EY9251

55min. 65min.

NOTE: This chart may include models that are not available in your area.

Please refer to the catalogue.

Charging time : Approximate one full charging time. May be different on battery pack

condition.

-

12

-

ONLY FOR U. K.

.

E L E C T R I C A L

PLUG INFORMA-

TION

FOR YOUR SAFETY PLEASE READ

THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded

three pin mains plug for your safety and

convenience.

A 3 amp fuse is tted in this plug.

Should the fuse need to be replaced please

ensure that the replacement fuse has a rat

-

ing of 3 amp and that it is approved by ASTA

or BSI to BS1362.

Check for the ASTA mark

or the BSI

mark on the body of the fuse.

If the plug contains a removable fuse cover

you must ensure that it is retted when the

fuse is replaced.

If you lose the fuse cover the plug must

not be used until a replacement cover is

obtained.

A replacement fuse cover can be purchased

from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UN

-

SUITABLE FOR THE SOCKET OUTLET IN

YOUR HOME THEN THE FUSE SHOULD

BE REMOVED AND THE PLUG CUT OFF

AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE

ELECTRICAL SHOCK IF THE CUT OFF

PLUG IS INSERTED INTO ANY 13 AMP

SOCKET.

If a new plug is to be tted please observe

the wiring code as shown below.

If in any doubt please consult a qualied

electrician.

IMPORTANT: The wires in this mains

lead are coloured in ac-

cordance with the follow-

ing code:

Blue:Neutral

Brown: Live

As the colours of the wire in the mains lead

of this appliance may not correspond with

the coloured markings identifying the termi-

nals in your plug, proceed as follows.

The wire which is coloured BLUE must be

connected to the terminal in the plug which

is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be

connected to the terminal in the plug which is

marked with the letter L or coloured RED.

Under no circumstances should either of

these wires be connected to the earth ter-

minal of the three pin plug, marked with the

letter E or the Earth Symbol .

How to replace the fuse: Open the fuse

compartment with a screwdriver and replace

the fuse and fuse cover if it is removable.

Fuse Cover

This apparatus was produced to BS800.

Page is loading ...

Matsushita Electric Works, Ltd.

Osaka, Japan

No.1 EN. GR. FR. IT. ND. ES. DN. SW. NR. FN. RUS. Uk

EY971068135 H1705 Printed in Japan

Panasonic EY 6813 Owner's manual

This manual is also suitable for

Panasonic EY 6813 Owner's manual

in other languages

Related papers

Other documents