ADJ Spherion Tri LED User manual

Brand: ADJ

Model: Spherion Tri LED

Category: DJ controllers

Type: User manual

Rev. 8/11

User Instructions

Unpacking: Thank you for purchasing the Spherion Tri LED by Amer-

ican DJ®. Every Spherion Tri LED has been thoroughly tested and has

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your xture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Do not return this unit to your dealer without rst contact-

ing customer support.

Introduction: The Spherion Tri LED is part of American DJ’s continu-

ing pursuit for creating and upgrading affordable intelligent fixtures The

Spherion Tri LED is an DMX intelligent centerpiece. This xture can be

used as a stand alone piece or connected in a Master/Slave congura-

tion. The unit can sound active, run in a auto mode or be controlled via

DMX controller. When using DMX control the fixture has a 1 Channel

mode and a 3 Channel mode.

Customer Support: American DJ® provides a toll free customer sup-

port line, to provide set up help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ®.

Spherion Tri LED General Information

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 2

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 3

• Bright 3 Watt LED

• 2 DMX Channel Modes - 1 Channel Mode & 3 Channel Mode

• DMX-512 Compatible

• Master/Slave Operation

• 4 Operating Modes - DMX Control, Sound Active, Show Mode, &

Program Mode.

• Optional UC3 Controller Compatible (Not Included)

Spherion Tri LED Main Features

The Spherion Tri LED carries a 3 year (1095 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase.

All returned service items whether under warranty or not, must be

freight pre-paid and accompany a return authorization (R.A.) number.

If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. Please contact American DJ® customer support for

a R.A. number.

Spherion Tri LED Product Registration

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break o the ground prong from the

electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 16 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (in-

cluding amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Spherion Tri LED Safety Precautions

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 4

Please carefully read and understand the instructions in this manual

thoroughly before attempting to operate this unit. These instructions

contain important safety information regarding the use and mainte-

nance of this unit. Please keep this manual with the unit, for future

reference.

Spherion Tri LED General Instructions

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 6©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 5

Spherion Tri LED Set Up Spherion Tri LED Set Up

Power Supply: The American DJ® Spherion Tri LED contains a auto-

matic voltage switch, which will auto sense the voltage when it is

plugged into the power source. With this switch there is no need to

worry about the correct power voltage, this unit can be plugged in

anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of dierent manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave

Operation): The Spherion Tri LED can be controlled via DMX-512 pro-

tocol. The Spherion Tri LED can be either a 1 or 3

channel DMX unit. The DMX address is set elec-

tronically using the controls on the rear panel of

the unit. Your unit and your DMX controller require

a approved DMX-512 110 Ohm Data cable for data

input and data output (Figure 1). We recommend

Accu-Cable DMX cables. If you are making your

own cables, be sure to use standard 110-120 Ohm

shielded cable (This cable may be purchased at

almost all professional sound and lighting stores). Your cables should

Figure 1

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground

XLR Male Socket

XLR Pin Conguration

3 Hot

2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

be made with a male and female XLR connector on either end of the

cable. Also remember that DMX cable must be daisy chained and

cannot be split.cable.

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 8©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 7

Spherion Tri LED Set Up

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Spherion Tri LED System Menu

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 10

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 9

Spherion Tri LED System Menu Spherion Tri LED System Menu

Operating Modes: The Spherion Tri LED can operate in four

different modes. In each mode you can run the fixture as a

stand alone fixture or in a master/slave confiugration. This next

section will detail the differences in the operating modes.

• Sound Active mode -

The fixture will react to sound.

• Show mode -

Choose 1 of 7 show modes to run.

• Program mode -

Choose 1 of 7 show modes to run.

• DMX control mode -

This function will allow you to control each individual fixtures traits

with a standard DMX-512 controller such as the Elation® Show

Designer.

™

System Menu: When making adjustments you can press

ENTER to conrm your setup or you can wait 8 seconds for

automatic setup. To exit without making any adjustments

press the MENU button.

ADDR - DMX Address Setting. See page 14 for more infor-

mation on DMX Control.

1. Press the either the MENU, UP, or DOWN buttons until

“ADDR” is displayed, press ENTER.

2. The current address will now be displayed and ashing.

Press the UP or DOWN buttons to nd your desired address.

Press ENTER to set your desired DMX address.

CHND - This will let select your desired DMX mode.

1. Press the either the MENU button until “CHND” is displayed,

press ENTER. Either “1CH” or “3CH” will be displayed

2. Press the UP or DOWN buttons to choose your desired DMX

mode and press ENTER to conm and exit.

SLND - This will let you set unit as a master or slave in a

master/slave conguration.

1. Press the MENU button until “SLND” is displayed, press

ENTER. Either “MAST”,“SL 1” or “SL 2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is

displayed, press ENTER to conm.

NOTE: In a Master/Slave conguration you can set one xture

to Master and then set the next xture to “SL 2”, the xtures will

now have contrast movement to each other.

SHND: SH 0 - SH 7 - Show modes 0-7 (Factory programs).

Show mode can be run with sound activity or without. For

show mode to run without sound activity turn sound activity

off.

1. Press the MENU button until “SHND” is displayed, press

ENTER.

2. “Sh X” will now be displayed, “X” representing a number

between 0-7. Programs 0-7 are factory programs, while “Sh 0”

is random mode. Press the UP or DOWN buttons to nd your

desired show and press the ENTER, then press and hold the

MENU button for at least 3 seconds to conrm.

Note: While running a Show, you can change the show instantly

by pressing the UP or DOWN buttons.

PROG - In this mode you can choose 1 of 7 colors and con-

trol rotation and rotation speed.

1. Press the MENU button until “PROG” is displayed, press

ENTER.

2. “CoLo” will now be displayed, press ENTER. “CoLX” will now be

displayed, “X” representing a number between 1-7. Use the UP

or DOWN buttons to scroll through the dierent colors. Once you

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 11

have found your desired color press ENTER.

3. Press the UP or DOWN button so that “ROTA” is displayed. In

this setting you can control rotation. Press the ENTER button,

“XXX” will be displayed. “XXX” representing a number between

0-255.

0-9 is no rotation, 10-113 is clockwise rotation fast-slow,

114-141 is no rotation, 142-245 is counter-clockwise rotation

slow-fast, and 248-255 is no rotation.

4. Adjust the rotation as you desire, then press ENTER.

SOUN - Sound Active mode.

1. Press the MENU button until “SOUN” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to activate sound active mode, or

“OFF” to deactivate sound active mode.

3. Press the ENTER, and then press and hold the MENU button

for at least 3 seconds to conrm.

SENS - Sound sensitivity control.

1. Press the MENU button until “SENS” is displayed, press

ENTER.

2. The display will show a number between 0-100. Press the UP

or DOWN buttons to adjust the sound sensitivity. 0 being the

least sensitive and 100 the most sensitive.

3. Press the ENTER, and then press and hold the MENU button

for at least 3 seconds to conrm.

BLND - Blackout or Stand by mode.

1. Press the MENU button until “BLND” is displayed, press

Spherion Tri LED System Menu

ENTER. Either Yes or No will be displayed.

2. To activate Blackout tap the UP or DOWN buttons until “Yes”

is displayed, press ENTER to conm. The xture will now be in

Blackout mode. To deactivate Blackout mode, select “No” and

press Enter.

LED - With this function you can have the LED display turn

o after 10 seconds.

1. Press the MENU button until “LED” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to keep the LED display on at

all times, or “OFF” to switch to have the LED display switch o

after 10 seconds.

3. Press ENTER to conrm.

DISP - This will “ip” the LED display 180º.

1. Press the MENU button until “dISP” is displayed, press

ENTER.

2. Either “dISP” or “dSIP” will now be displayed. Press the UP or

DOWN buttons to select one or the other.

3. Press the ENTER, and then press and hold the MENU button

for at least 3 seconds to conrm.

TEST - This function will run a self test program.

1. Press the MENU button until “TEST” is displayed, press

ENTER.

2. The xture will now run a self test.

FHRS - With this function you can display the running time

Spherion Tri LED System Menu

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 12

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the chases and patterns,

dimmer and strobe. A DMX controller allows you to create unique

programs tailored to your individual needs.

1. The Spherion Tri LED can be either a 1 or 3 DMX channel fixture.

See page 15 for detailed description of the DMX values and

traits.

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 6-8 as well as the set-up specifications that are includ-

ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instructions on page 9 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Spherion Tri LED DMX Control

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 13 ©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 14

Spherion Tri LED System Menu

of the xture.

1. Press the MENU button until “FHRS” is displayed, press

ENTER.

2. The running time of the xture will now be displayed. Press

MENU to exit.

VER - With this function you can display the version soft-

ware of the xture.

1. Press the MENU button until “VER” is displayed, press

ENTER.

2. The software version will now be displayed. Press MENU to

exit

RSET - Use this function to reset the unit.

1. Press the MENU button until “RSET” is displayed, press

ENTER.

2. The xture will now reset

Master-Slave Operation This function will allow you to link up to 16

units together and operate without a controller. The units will be sound

activated. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. On the Master unit find and run your desired operating mode.

3. On the slave units tap the MENU button until “SLND” is dis-

played, and Press ENTER. See page 9 under “SLND” for more

infomation.

4. The slave units will now follow the Master unit.

Spherion Tri LED Master-Slave Configuration

Spherion Tri LED Fuse Replacement

Disconnect the unit’s main power supply. Insert a standard flat head

screw driver in to the fuse holder housing. Turn the screwdriver in

counter-clockwise direction to remove the fuse holder. Remove the

old fuse and discard it, replace the fuse with the same type. Insert

the fuse holder back into it’s housing and turn in clockwise direction

to lock the holder in place.

Spherion Tri LED Cleaning

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the

internal and external optical lenses and mirror should be carried out

periodically to optimize light output. Cleaning frequency depends on

the environment in which the fixture operates (I.e. smoke, fog residue,

dust, dew). In heavy club use we recommend cleaning on a monthly

basis. Periodic cleaning will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Use a brush to wipe down the cooling vents and fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every

20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

Spherion Tri LED 1 DMX Channel Mode - DMX Traits

Channel Value Function

1 SHOWS

0 - 7 BLACKOUT

8 - 47 SHOW 1

48 - 87 SHOW 2

88 - 127 SHOW 3

128 - 167 SHOW 4

168 - 207 SHOW 5

208 - 247 SHOW 6

248 - 255 SOUND ACTIVE

Spherion Tri LED UC3 Control

Blackout Blackout the unit

Function

1. Synchronous Strobe in white

2. Asynchronous Strobe in whtie

3. Sound Strobe in color

Select color

1. Red

2. Green

3. Blue

4. Red+Green

5. Green+Blue

6. Red+Blue

7. Red+Green+Blue

8. Color change by sound

Select

Show(1-7)

Mode

Sound

(LED OFF)

Manual Color

(LED ON)

Show(LED

slow

blinking)

Channel Value Function

1 ROTATION

0 - 9 STOP

10 - 120 CLOCKWISE ROTATION FAST-SLOW

121 - 134 STOP

135 - 245 COUNTER-CLOCKWISE ROTATION

SLOW - FAST

246 - 255 STOP

2 DIMMER & STROBE

0 - 7 OFF

8 - 199 DIMMER 0% - 100%

200 - 247 STROBING FAST - SLOW

248 - 255 ON

3 COLOR

0 - 46 COLOR 1

47 - 85 COLOR 2

86 - 124 COLOR 3

125 - 163 COLOR 4

164 - 202 COLOR 5

203 - 240 COLOR 6

241 - 255 COLOR 7

Spherion Tri LED 3 DMX Channel Mode - DMX Traits

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 15 ©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 16

Spherion Tri LED Warranty

MANUFACTURER’S LIMITED WARRANTY

A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American

Audio products to be free of manufacturing defects in material and workmanship for a prescribed

period from the date of purchase (see specic warranty period on reverse). This warranty shall be

valid only if the product is purchased within the United States of America, including possessions

and territories. It is the owner’s responsibility to establish the date and place of purchase by ac-

ceptable evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before

sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send

the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the

requested repairs or service (including parts replacement) are within the terms of this warranty,

American DJ, Inc. will pay return shipping charges only to a designated point within the United

States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories

should be shipped with the product. If any accessories are shipped with the product, American DJ,

Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the

safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is

modied in any manner which American DJ, Inc. concludes, after inspection, aects the reliability

of the product; if the product has been repaired or serviced by anyone other than the American DJ,

Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the

product is damaged because not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period specied above, American DJ, Inc. will replace defec-

tive parts at its expense with new or refurbished parts, and will absorb all expenses for warranty

service and repair labor by reason of defects in material or workmanship. The sole responsibility

of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replace-

ment thereof, including parts, at the sole discretion of American DJ. All products covered by this

warranty were manufactured after January 1, 1990, and bear identifying marks to that eect.

E. American DJ, Inc. reserves the right to make changes in design and/or improvements

upon its products without any obligation to include these changes in any products theretofore

manufactured. No warranty, whether expressed or implied, is given or made with respect to any

accessory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ, Inc. in connection with this product, including

warranties of merchantability or tness, are limited in duration to the warranty period set forth

above. And no warranties, whether expressed or implied, including warranties of merchantability

or tness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s

sole remedy shall be such repair or replacement as is expressly provided above; and under no

circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,

arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to American DJ and American Audio

Products and supersedes all prior warranties and written descriptions of warranty terms and

conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Ampli-

ers)

• All American Audio V-Plus Series Ampliers = 3-year (1095 day) Limited Warranty

• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty

(Such as: Special Eect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble

Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,

and Star Tec Series)

• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty

• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which

have a 1-year (365 day Limited Warranty)

©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 17 ©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 18