Sharp AR-800 imager User manual

Category
Copiers
Type
User manual

This manual is also suitable for

DIGITAL COPYING MACHINE
OPERATION MANUAL
MODEL
AR-650
❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧
❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧
❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧
❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧❧
➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣
➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣
➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣
➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣
The power switch positions are marked “ ” to indicate power “ON” and
” to indicate stand-by.
In the stand-by position, power is being supplied to a drying heater within
the optical system of the copier.
Caution:
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be
easily accessible.
FOR YOUR RECORDS ...
To protect against loss or theft, record and retain for reference the
copier’s serial number located on the left hand side at the rear corner of
the copier.
Model Number
AR-650
Serial Number
Date of Purchase
Place of Purchase
Authorized Sharp Copier
Service Department Number
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This Class [A] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme á la norme NMB-003 du Canada.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this
equipment not expressly approved by the manufacturer could void the user’s
authority to operate this equipment.
EPA ENERGY STAR ® (MFD)
EPA ENERGY STAR Program-
The United States Environmental Protection Agency (EPA) has introduced a voluntary program, the
ENERGY STAR Program, to enourage the widespread and voluntary use of energy-efficient technologies
that enhance the workplace, improve product performance and prevent pollution. As an ENERGY STAR
Partner, the Sharp Corp. has determined that this copier model meets the ENERGY STAR guidelines for
energy efficiency.
ENERGY STAR guidelines for this class of copier require ENERGY STAR copiers to have an 'Off Mode'
feature that automatically turns the copier off after a period of inactivity, ensuring night and weekend
shut-off. The copier must also automatically change to a 'Low Power Mode' (Automatic Energy Save)
after a period of time since the last usage.
For Copier+Printer or FAX model, ENERGY STAR guidelines for this class of copier require ENERGY
STAR Multifunction copiers to have a 'Sleep Mode' feature that automatically makes the copier enter
the sleep mode after a period of inactivity. The copier must also automatically change to a 'Low Power
Mode' (Automatic Energy Save) after a period of time since the last usage.
Specifically, this copier complies with the following requirements-
The AR-650 Copier model (Base model)
'Off Mode'-
The copier consumes less than 20 watts in the 'Off Mode'.
'Off Mode' Default Time-
The default time for the 'Off Mode' is 90 minutes.
'Automatic Energy Save'-
The copier consumes less than 255 watts during Energy Save.
'Automatic Energy Save' Default Time-
The default time for the 'Automatic Energy Save' is 15 minutes.
The AR-650 Copier + Printer model (Multifunction model)-
'Sleep Mode'-
The copier consumes less than 95 watts in the 'Sleep Mode'.
'Sleep Mode' Default Time-
The default time for the 'Sleep Mode' is 90 minutes.
'Automatic Energy Save'-
The copier consumes less than 300 watts during Energy Save.
'Automatic Energy Save' Default Time-
The default time for the 'Automatic Energy Save' is 15 minutes.
Note1- The default setting for the 'Off Mode' or 'Sleep Mode' and 'Automatic Energy Save' can be
changed. If you want to increase the default setting, contact your authorized Sharp dealer.
Note2- For Copier model (Base model), to restart the copier after an automatic shut-off, return the
power switch to the 'On' position.
Note3- For Copier model (Base model), after an automatic shut-off, the weekly timer feature cannot be
activated. If you prefer to activate this feature, contact your authorized Sharp dealer.
In accordance with the EPA ENERGY STAR Program guidelines, Sharp recycled paper.
If you have any questions regarding the use of recycled paper or some recommended types of recycled
paper, please contact your authorized Sharp dealer.
ENERGY STAR is a U. S. registered mark.
1
PREFACE
CONTENTS
PRECAUTIONS
PREFACE
Thank you for purchasing the Sharp Digital Copier AR-650. This Operators Manual describes the
following:
how to use the digital copier
how to make copies
how to inspect and carry out maintenance on the digital copier
how to remedy mechanical and copying problems.
Before using the digital copier, thoroughly read and understand this Operators Manual. To ensure that
clean copies are made at all times and to make sure that the digital copier is in optimum working order,
keep this Operators Manual in a handy place for future reference.
COPYRIGHT 2000
SHARP CORPORATION
n To ensure correct and safe use of the Sharp Digital Copier AR-650, this Operators Manual
describes safety precautions according to the following three levels of warning:
Before reading this Operators Manual, you should fully understand the meaning and importance
of these signal words.
Warning ------ Indicates a potentially hazardous situation which, if not avoided, could result in
death, serious injury, or serious damage, or fire in the equipment or surrounding
area.
Caution ------- Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury, partial damage of the equipment or surrounding
area, or loss of data.
Note------------ Indicates a procedure you should follow to ensure the optimal performance of
the digital copier and problem-free copying.
Tip -------------- Describes information useful to know when operating the digital copier.
Advice --------- Describes an operation you should follow to maintain the digital copier in good
working order.
User Safety
This Sharp digital plain paper copier does not produce laser radiation hazardous to the user. It is certified
as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation
Performance Standard according to the Radiation Control for Health and Safety Act of 1968.
Protective housing and external covers completely confine the laser light emitted inside the plain paper
copier. The laser beam cannot escape from the machine during any phase of user operation.
Regulations implemented on August 2, 1976 by the Bureau of Radiological Health (BRH) of the U.S. Food
and Drug Administration apply to laser products manufactured from August 1, 1976. Laser products
marketed in the United States must comply with these regulations.
CAUTION: Using controls or adjustments or performing procedures, other than those specified
herein may result in hazardous radiation exposure.
2
The copier is a plain paper digital copier.
The copier scans originals and stores the resulting data in its memory as digital images. The
copier allows you not only to process and edit these digital image data, but also enables copies
to be sorted and grouped quietly, quickly and easily. The copier incorporates a large-size
display with a touch panel and menu buttons that graphically represent copier functions. As
a result, anybody can make clear-looking copies quickly and easily.
The copier also has the following convenient features which allow the digital copier to be used
in many applications.
. Copying speed is 65 copies (Letter) per minute for the copier.
. The automatic original density function automatically reads the density of the original to
set the ideal copy density.
. The size of the original is automatically read and the appropriate paper size and reproduction
ratio are automatically selected.
. Wide reproduction range (25% to 400%).
. Duplex copies or single-sided copies can be made automatically from two-sided originals.
Duplex copies can also be made automatically from single-sided originals.
. Comes with the following digital editing functions:
Trimming, masking, negative/positive reversal, X-Y zoom and mirror image, etc.
. Comes with the following memory editing functions:
2 in 1, 4 in 1, document storage, annotation and page numbering.
. With the electronic sort function, you can also sort at high speed without damaging the
originals.
. The cover-sheet mode allows you to add cover pages at the first and/or last pages of the
copies. The sheet-insertion mode allows you to insert copied and/or blank sheets at user-
specified pages.
. Copy sizes from Statement up to Ledger are acceptable.
. Adding the optional finisher permits the stapling and sorting of copies as well as magazine
sorting (AR-FN9: with the saddle stitching function, AR-FN8 : without the function). An
optional hole punching unit can be installed.
. Comes with a weekly timer. This timer allows automatic turning ON or OFF of the power
supply at the specified startup or shutdown times, respectively.
. An automatic job start mode. This mode allows you to start copying when warming-up is
completed after you have set the desired copy modes and pressed the START key.
Installing an optional printer unit allows you to print out data from PCs.
Features of the AR-650 copier
PREFACE
3
TABLE OF CONTENTS
PREFACE .................................................................................................................... 1
TABLE OF CONTENTS ............................................................................................. 3
PRECAUTIONS .......................................................................................................... 5
1. INSTALLATION..................................................................................................................... 5
2. GENERAL PRECAUTIONS ................................................................................................... 6
DESCRIPTION OF THE DIGITAL COPIER ............................................................... 7
1. NAMES OF MAIN COMPONENTS..................................................................................... 8
2. DESCRIPTION OF OPTIONAL EQUIPMENT ...................................................................... 9
3. DESCRIPTION OF THE CONTROL PANEL ...................................................................... 10
4. DESCRIPTION OF THE GRAPHIC DISPLAY .................................................................... 13
HOW TO MAKE COPIES........................................................................................ 15
1. TURNING ON THE POWER SWITCH / AUTO JOB START .......................................... 16
2. USING THE REVERSING AUTOMATIC DOCUMENT FEEDER...................................... 19
3. COPYING IN THE AUTOMATIC PAPER SELECTION MODE ........................................ 24
4. ACTUAL-SIZE COPYING BY SPECIFYING THE COPY SIZE.......................................... 27
5. REDUCTION AND ENLARGEMENT COPYING................................................................ 29
6. DUPLEXED COPIES FROM SINGLE-SIDED ORIGINALS ............................................... 34
7. DUPLEXED COPIES FROM TWO-SIDED ORIGINALS .................................................... 39
8. SINGLE-SIDED COPIES FROM TWO-SIDED ORIGINALS .............................................. 41
9. DUPLEXED COPIES FROM BOOK ORIGINALS .............................................................. 43
10. COPYING WITH COPY DENSITY SELECTION ................................................................ 46
11. COPYING IN THE TEXT OR PHOTO MODE ................................................................... 47
12. BYPASS COPYING ............................................................................................................. 48
13. BYPASS COPYING BY SPECIFYING THE COPY SIZE................................................... 50
14. INTERRUPT COPYING ....................................................................................................... 52
15. PRESETTING OF COPY MODES ...................................................................................... 53
16. ALL CLEAR KEY ................................................................................................................. 54
USING THE EDITING FUNCTIONS....................................................................... 55
1. IMAGE SHIFT COPYING.................................................................................................... 56
2. EDGE ERASE COPYING .................................................................................................... 58
3. DUAL-PAGE COPYING ...................................................................................................... 60
4. X-Y ZOOM .......................................................................................................................... 61
5. TRIMMING/MASKING........................................................................................................ 62
6. MIRROR IMAGE ................................................................................................................. 66
7. NEGATIVE/POSITIVE REVERSAL...................................................................................... 67
8. 2 IN 1 / 4 IN 1.................................................................................................................... 69
9. ANNOTATION..................................................................................................................... 73
10. PAGE NUMBER .................................................................................................................. 75
11. MAGAZINE SORT .............................................................................................................. 78
12. COVER SHEET COPYING .................................................................................................. 80
13. SHEET INSERTION COPYING........................................................................................... 84
14. SETTING A CASSETTE FOR COVER SHEET/SHEET-INSERTION COPYING............... 87
15. DOCUMENT STORAGE ..................................................................................................... 89
PREFACE
CONTENTS
PRECAUTIONS
DESCRIPTION
OF THE DIGITAL
COPIER
HOW TO
MAKE
COPIES
WHEN THE
GRAPHIC SYMBOLS
FLASH
MAINTE-
NANCE
SPECIFICATIONS,
ACCESSORIES &
OPTIONS
USING THE
EDITING
FUNCTIONS
USING THE
SPECIAL
FUNCTIONS
USING THE
OPTIONAL
FINISHER
4
USING THE SPECIAL FUNCTIONS....................................................................... 93
1. ACCOUNT NUMBER.......................................................................................................... 94
2. JOB MEMORY .................................................................................................................... 95
3. WEEKLY TIMER.................................................................................................................. 99
4. COPYING USING PAPER OF OTHER SIZES................................................................. 101
5. SETTING THE DATE AND TIME .................................................................................... 102
6. CHANGING AUTOMATIC ENERGY SAVE TIME/AUTOMATIC SHUTOFF TIME....... 104
7. CHANGE OF LANGUAGE ON THE DISPLAY PANEL.................................................. 105
USING THE OPTIONAL FINISHER.......................................................................107
1. NAMES OF THE MAIN COMPONENTS ........................................................................ 108
2. NON-SORT COPYING ...................................................................................................... 109
3. SORT COPYING................................................................................................................ 110
4. GROUP COPYING ............................................................................................................ 114
5. STAPLING ......................................................................................................................... 118
6. HOLE PUNCHING MODE ................................................................................................ 122
7. MAGAZINE SORT & SADDLE STITCHING MODE....................................................... 124
WHEN THE GRAPHIC SYMBOLS FLASH ...........................................................127
1. ADD PAPER SYMBOL ..................................................................................................... 128
2. REPLACE TONER BAG SYMBOL ................................................................................... 130
3. ADD TONER SYMBOL..................................................................................................... 132
4. CLEAR PAPER SYMBOL.................................................................................................. 136
5. CHECK ORIGINAL SYMBOL ........................................................................................... 147
6. FINISHER/HOLE PUNCHING UNIT MISFEED SYMBOL............................................... 149
7. SADDLE STITCHER JAM SYMBOL................................................................................ 152
8. REPLACING STAPLES (OPTIONAL) ............................................................................... 154
9. REMOVING JAMMED STAPLES (OPTIONAL) .............................................................. 159
10. CLEARING ACCUMULATED PUNCHED PAPER BITS.................................................. 164
11. CALL SERVICE SYMBOL................................................................................................. 165
12. PERIODIC MAINTENANCE .............................................................................................. 166
MAINTENANCE ......................................................................................................167
1. DAILY INSPECTION ......................................................................................................... 168
2. SIMPLE TROUBLESHOOTING ........................................................................................ 169
SPECIFICATIONS, ACCESSORIES & OPTIONS..................................................171
1. SPECIFICATIONS.............................................................................................................. 172
2. FINISHER SPECIFICATIONS (OPTIONAL)...................................................................... 174
TABLE OF CONTENTS (Cont.)
5
PREFACE
CONTENTS
PRECAUTIONS
PRECAUTIONS
1. INSTALLATION
3
2
1
The copier should be installed by a qualified service technician.
Note: The packing material should be disposed of properly.
To obtain the best possible results, this copier should be used in conjunction with a
dedicated AC power line at the following ratings:
115V60 Hz, 16 A
Notes:
1. The use of other appliances or other equipment on the same line as this copier may adversely
affect performance and copy quality.
2. Be sure to use a 3-conductor, grounded wall outlet.
3. In areas where a 2-pin plug is used, the copier must be grounded for safety.
Never ground it to a gas pipe, a water pipe, or any other object not suitable for grounding.
After a suitable place has been selected for the installation of the copier, please do not
change it. Avoid excessive heat, dust, vibration and direct sunlight. Also, provide
proper ventilation as the copier emits a small amount of ozone.
Notes:
1. Recommended environmental range for use is as follows:
Temperature: 10~30˚C/50~86˚F
Humidity: 20~85% RH
2. To insure optimal operation, allow clearances of at least 32" on the left, 32" on the right
and 4" in the rear (refer to the illustration below).
The socket-outlet shall be installed near the equipment and shall be easily accessible.
4 inches
32 inches
32 inches
6
1
2. GENERAL PRECAUTIONS
Handle and use the copier gently and carefully.
. Do not place anything on the paper cassettes or the original feed tray.
. Never allow the power cable to be trampled on or pinched between hard objects, otherwise
an accident or electrical trouble might occur.
. Do not allow any metal items such as paper clips to fall into the copier.
Be sure to turn OFF the power switch (unless using the automatic timer mode):
. When you leave your office at night.
. If a power failure occurs.
Caution: When turning OFF the power switch, be sure to do so only after the machine cycling
has come to a complete stop.
Be sure to disconnect the power-cord plug:
. when you do not intend to use the copier for an extended period of time.
Be sure to turn OFF the power switch immediately and call for service:
. If an unusual noise is heard from the copier.
. If the outside of the copier becomes unusually hot.
. If any part of this copier is damaged, or if it has been dropped.
. If the copier has been exposed to rain or liquid.
It is recommended that only supplies made or designated by Sharp be used for the
copier in order to optimize copy quality. All supplies should be stored in a cool, dry area.
For optimum performance, it is recommended that 22lb. xerographic bond paper of high quality
be used.
Paper of lower quality may contain inherent properties such as excess paper dust and may
lead to premature servicing.
WARNING–DO NOT LEAN ON, APPLY FORCE OR PLACE HEAVY OBJECTS ON THE
FINISHER. PERSONAL INJURY OR PROPERTY DAMAGE MAY RESULT.
2
PRECAUTIONS
(Cont.)
3
"BATTERY DISPOSAL"
CONTAINS MANGANESE DIOXIDE LITHIUM BATTERY. MUST BE DISPOSED OF
PROPERLY. CONTACT YOUR SHARP DEALER OR SERVICER FOR INSTRUCTIONS.
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or the Electronics Industries
Alliance:www.eia.org
7
DESCRIPTION
OF THE DIGITAL
COPIER
DESCRIPTION OF THE DIGITAL COPIER
8
1. NAMES OF MAIN COMPONENTS
Cassette
Control panel
Automatic
document feeder
(ADF)
Glass
Original scale
Right-hand front door
Large capacity feeder
Used toner bag door
Tray-down key
Toner hopper lid
Left-hand front
door
Operator's manual
pocket (back side)
Power switch
Sheet bypass
C
L
A
S
S
1
L
A
S
E
R
P
R
O
D
U
C
T
L
A
S
E
R
K
L
A
S
S
E
1
A
P
P
A
R
E
I
L
A
L
A
S
E
R
D
E
D
L
A
S
S
E
1
'
P
R
O
D
U
C
T
I
S
C
E
R
T
I
F
I
E
D
B
Y
THE
M
A
N
U
F
A
C
T
U
R
E
R
TO
C
O
M
P
L
Y
WITH DHHS
RULE 21
C
F
R
S
U
B
C
H
A
P
T
E
R
J APPLICABLE
AT
THE DATE OF MANUFACTURE
.
J
S
M
A
N
U
FA
C
TU
R
E
D
:
Y
Certification Label
Explanatory Label
CLASS
1
LASER
PRODUCT
LASER
KLASSE 1
APPAREIL
A
LASER
DE
DLASSE 1
'
PRODUCT
IS
CERTIFIED
BY
THE
MANUFACTURER
TO
COMPLY
WITH DHHS
RULE 21
CFR
SUBCHAPTER
J APPLICABLE
AT
THE DATE OF MANUFACTURE
.
JS
MANUFACTURED
: Y
Identification Label
Warning Label
Touch panel contrast
adjustment volume
9
DESCRIPTION
OF THE DIGITAL
COPIER
2.
DESCRIPTION OF OPTIONAL EQUIPMENT
1. Finisher (AR-FN8, AR-FN9)
The finisher allows SORT, GROUP, STAPLE copying, MAGAZINE SORT, MAGAZINE SORT
& SADDLE STITCH, SADDLE STITCH and HOLE PUNCH as well as NON-SORT copying.
2. Hole Punching Unit
The hole punching unit is the option for the finishers.
* The saddle stitching function is available when the AR-FN9 is installed.
1
2
10
3.
DESCRIPTION OF THE CONTROL PANEL
Clip tray
Put any paper clips re-
moved from the originals
here.
INTERRUPT key
When you want to make
a copy of a different ori-
ginal during a multicopy
run, press this key. During
interrupt-copying, you
can make copies only one
at a time. To return to the
previous multicopying
run, press this key again.
ENERGY SAVER key
When you are not using
the copier for a fairly long
period of time, press this
key. The copier enters the
energy-saving mode, and
all display lamps go out.
To resume copying, press
this key again. After a
short while, the copier
becomes ready for
copying.
TOTAL COUNTER
Displays the total number
of copies made after the
copier was installed.
PRINTER/NETWORK key
If you have an optional
printer installed, press
this key to access the
printer function.
COPY key
If you have an optional
printer installed, press
this key to select the copy
function.

HELP
ENERGY SAVER
TIMER
INTERRUPT
COPY
PRINTER/NETWORK
11
DESCRIPTION
OF THE DIGITAL
COPIER


 
OPERATION GUIDE key
Pressing the HELP key
displays the appropriate
operation procedure.
Pressing this key after a
function has been set
displays the features
available.
MESSAGE display
Displays the status of the
copier, operation proce-
dures and various
instructions to the user in
short sentences and
graphics.
DIGITAL keys
Use these keys to enter
the desired copy quantity.
You can set up to 999
copies.
 ALL CLEAR key
When you press this key,
all the modes you have
selected are cleared to the
default settings.
 STOP key
Press this key to stop a
copy run.
 START key
Press this key to start
copying.
 CLEAR key
Use this key to correct the
entered copy quantity.
1 2 3
4 5 6
7 8 9
0C
ALL CLEAR
STOP
START
CLEAR
12
The Message Display panel shows operation status,error messages and function menus.
.
Each function item displayed is shown in the form of a touch key.You can select the function
by touching the key lightly with your finger.
.
Touching one of the function items will show the next display.
The function items shown on the right can be selected directly on the Message Display panel.
* The brightness of the touch panel can be adjusted with the touch panel contrast adjustment
volume. Open the front doors and find it on the back side of the control panel. (Refer to the
illustration on the page8.)
3.
DESCRIPTION OF THE CONTROL PANEL (Cont.)
Note: All the numbers are approximate. The
numbers in parentheses are for the large-
capacity feeder.
: 500 ~ 376 (4000 ~2001)
: 375 ~ 251 (2000 ~1001)
: 250 ~ 126 (1000 ~ 501)
: 125 ~ 1 ( 500 ~ 1)
Message
Reproduction Ratio
Copy Quantity
Paper size of the currently selected paper source
Paper Indicator: Indicates the remaining number of sheets.
The table to show the relation between the paper size display on this
machine and the actual dimensions is as follows:
Paper Size Dimensions
LT 8-1/2" x 11"
LD 11" x 17"
LG 8-1/2" x 14"
ST-R 5-1/2" x 8-1/2"R
COMP 10-1/8" x 14"
FOLIO 8.27" x 13"
LG13 8-1/2" x 13"
13
DESCRIPTION
OF THE DIGITAL
COPIER
The graphic display shows the status of the copier. When one of the graphic symbols flashes,
take the appropriate action referring to the page shown.
4.
DESCRIPTION OF THE GRAPHIC DISPLAY


14
4.
DESCRIPTION OF THE GRAPHIC DISPLAY (Cont.)
SADDLE STITCHER JAM
Symbol
This symbol flashes when
paper is misfed in the
saddle stitcher. (See page
152.)
CLEAR PAPER symbol
This symbol flashes when
paper is misfed in the
automatic duplexer. (See
page 141~144.)
FINISHER/HOLE
PUNCHING
UNIT MISFEED symbol
This symbol flashes when
paper is misfed in the
optional finisher or hole
punching unit. (See page
149.)
CLEAR PAPER symbol
This symbol flashes when
paper is misfed on the
paper path inside the
copier. (See page 136.)
CALL SERVICE symbol
This symbol flashes when
maintenance by a service
technician is necessary.
(See page 165.)
CHECK ORIGINAL
symbol
This symbol flashes when
an original is misfed
inside the automatic
document feeder. (See
page 147.)
ADD TONER symbol
This symbol flashes when
the toner hopper is empty.
(See page 132.)
BYPASS MISFEED
symbol
This symbol flashes when
no paper is fed into the
copier in bypass copying.
Remove and reset the
sheets on the sheet
bypass. (See page 146.)
CLEAR PAPER symbol
This symbol flashes when
a sheet of paper fed from
the large-capacity feeder
is misfed in the paper feed
section. (See page 146.)
 REPLACE TONER BAG
symbol
This symbol flashes when
the toner bag in use
becomes full of used
toner. (See page 130.)
 CLEAR PAPER symbol
This symbol flashes when
a sheet of paper fed from
the selected cassette is
misfed in the paper
feeding section. (See page
145.)
15
HOW TO
MAKE
COPIES
HOW TO MAKE COPIES
16
1
2
3
1. TURNING ON THE POWER SWITCH / AUTO JOB START
Turn ON the power switch.
Turning ON the Power Switch
The message Wait Warming Up appears.
. Wait until the copier becomes ready.
About 7 minutes later, the message
READY appears.
. This message indicates that you can make
copies at any time.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181

Sharp AR-800 imager User manual

Category
Copiers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI