Emerson SITETPI-E V3 User manual

Emerson
Brand
Emerson
Model
SITETPI-E V3
Category
Power supply units
Type
User manual

Emerson SITETPI-E V3 is an Ethernet-ready device designed to interface specifically with a SiteScan Web system. It is a 32-bit microprocessor-based device designed to monitor third-party equipment via an EIA-485/232 Modbus interface. Logically, the device sits on the Ethernet network, providing the interface to SiteScan Web. This effectively creates a router/gateway and third-party interface in a single device. Screw terminal blocks are provided to terminate power, communication, and input signal wiring.

Some of the key capabilities of the Emerson SITETPI-E V3 include:

  • Ethernet connectivity: The device can be connected to an Ethernet network, allowing it to communicate with other devices on the network, including the SiteScan Web system.

Emerson SITETPI-E V3 is an Ethernet-ready device designed to interface specifically with a SiteScan Web system. It is a 32-bit microprocessor-based device designed to monitor third-party equipment via an EIA-485/232 Modbus interface. Logically, the device sits on the Ethernet network, providing the interface to SiteScan Web. This effectively creates a router/gateway and third-party interface in a single device. Screw terminal blocks are provided to terminate power, communication, and input signal wiring.

Some of the key capabilities of the Emerson SITETPI-E V3 include:

  • Ethernet connectivity: The device can be connected to an Ethernet network, allowing it to communicate with other devices on the network, including the SiteScan Web system.
1
SITETPI-E V3
Product Specification/Installation Sheet
Description
The Liebert SiteTPI-E is an Ethernet-
ready device intended to interface
specifically to a SiteScan Web system.
It is a 32-bit microprocessor-based
device designed to monitor third-party
equipment via an EIA-485/232
Modbus interface.
Logically the device sits on the
Ethernet network, providing the
interface to SiteScan Web. This
effectively creates a router/gateway
and third-party interface in a single
device. Screw terminal blocks are
provided to terminate power,
communication and input signal
wiring.
Module Dimensions and Layout
Module
Address
Format
On Off
Power
CONTROL MODULE
24V ac/dc
Ground
EIA-485
EIA-232
485-4w
485-2w
Archive Valid
Port S1 receive
Port S1 transmit
BACnet receive
BACnet transmit
Battery low
Status
Module
2 wire 4 wire
Rx -
Net-
Net+
n/c
Tx -
Tx +
Rx +n/c
EIA-232
DCD
Rx
Tx
DTR
Signal Ground
Ext. Batt.
Int. Batt.
External
Battery
Gnd
+3V
Blinking Dot = 'Run'
Port S1
Class 2
Use Copper Conductors Only
24Vac, 24VA, 1A, 50-60 Hz
Without Keypad Display:
26Vdc, 10W, 0.4A
Open Energy
Management Equipment
88FO
E143900
TYPE: 002001
R
Power
LED
Error Codes:
0 = Download required
1 = Control Program Error
2 = RAM full
3 = Comm setup error
4 = System error
8 = Formatting
Chase = OK
Option
Comm
IP Addr
Default
Assigned +100
0
Address
Enable
Disable
on S1
On
Off
MSTP
Enable
Disable
on S2
PTP
Shield
Net -
Net +
Port S2
Local Access
Rnet
10/100 BaseT
Ethernet Port E1
BACnet
100 LAN LINK
Gnd
Rnet +
Rnet -
+12V
®
BACnet
Over ARCNET156 KBaud
BT485
BT485
EIA-485
EIA-232
485
n/c
n/c
Net+
Net-
232
Tx
DTR
DCD
Rx
Signal Gnd
EIA-
Tx
Rx
BT485
Made in USA
3V Lithium Battery
CR-123A
Enhanced Access
Port on S2
and Rnet
10's 1's
SiteTPI-E
™
Ethernet
port
Port S1
Options
comm
Local access
port
2.5"
(64mm)
1.25"
(32mm)
7.5"
(190.5mm)
Diagnostic
LED indicators
Port S2
Rnet port
BACnet
port
2.5"
(64mm)
1.25"
(32mm)
11.295"
(286.9mm)
0.23"
(5.8mm)
Power
connector
2
Power Wiring Diagrams
Enclosure Dimensions
3
Enclosure Mounting
The enclosure may be mounted on a wall or on the floor. Refer to the following diagrams for
your application.
Enclosure Wall Mounting Diagram
Enclosure Floor Mounting Diagram
4
© 2006 Liebert Corporation
All rights reserved throughout the world. Specifications subject
to change without notice.
® Liebert and the Liebert logo are registered trademarks of
Liebert Corporation. All names referred to are trademarks or
registered trademarks of their respective owners.
SL-28105 (2/06) Rev. 1
Liebert Corporation
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Telephone: 1-800-877-9222
Facsimile: 1-614-841-6022
www.liebert.com
Specifications
Diagnostic LEDs
Wiring Specifications
Ordering Information
Power 24VAC ±10%, 50 to 60Hz, 24VA, or 26VDC ±10%, 10W
Dimensions
W x D x H: in. (mm)
Module:
11.295 x 0.56 x 7.5 (286.9 x 14.2 x 190.5)
Enclosure (painted steel):
14.25 x 2.85 x 12 (362 x 72.4 x 304.8)
Communication
• One (1) Ethernet 10/100BaseT RJ-45 port
• One (1) Configurable Serial Port - EIA-232 or 485 (2- or 4-wire)
• 5-position Terminal Block
• One (1) CMnet EIA-485 Port - Control Module network screw terminals
• Switch-selectable baud rates ARC156 / 9600 or 38.4bps
• Recommended wire: MAGNUM Cable P/N A3-ARC-156-2
• BACnet Port (ARCNET156 or EIA-485 communication): In ARCNET156 mode, the port speaks
BACnet ARC156. In EIA-485 mode, DIP switch settings specify baud rate and protocol: BACnet
MS/TP or Modbus (RTU or ASCII).
• Port S1 (BMS connection): Normally configured for a Building Management System; may be
configured for EIA-485 or EIA-232. Supports BACnet MS/TP, BACnet PTP and Modbus (RTU or
ASCII) protocols.
• Port S2 (MFR connection): Connection to manufacturer’s equipment; jumper enables EIA-485 or
EIA-232 mode. Supports BACnet MS/TP, BACnet PTP and Modbus (RTU or ASCII) protocols.
• Rnet: Local laptop and/or BACview access port. Conforms to the BACnet Advanced Application
Controller (B-AAC) Standard Device as defined in BACnet 135-2001 Annex L.
Environmental
Operating Range
20°F to 140°F (-29°C to 60°C); 10 to 90% relative humidity, non-condensing.
Note: Control modules should be installed within the building.
Memory
16 MByte non-volatile battery-backed SDRAM (with 12 MBytes available for use)
8 MByte Flash memory, 32-bit memory bus
Protection Built-in surge and transient protection circuitry
Battery 3V lithium battery P/N CR-123A; battery shelf life is 10 years with 720 hours of continuous operation
Fault Detection Hardware watchdog timer
Agency Listings UL916 (Canadian Std C22.2 No. 205-M1983), CE, FCC Part 15 - Subpart B - Class A
Indicator Description Indicator Description
BACnet transmit Blinks when data is transmitted Port S1 transmit Blinks when data is transmitted
BACnet receive Blinks when data is received Port S1 receive Blinks when data is received
Archive Valid N/A Battery low Blinks when the battery is low
Connection Supported Wire Types Maximum Wire Length Rating
Ethernet 10 BaseT CAT 5 328 ft. (100m) N/A
Port S1 ARCnet MAGNUM Cable P/N A3-ARC-156-2 3000 ft. (915m) N/A
Port S2 EIA-485
18-22 AWG Stranded & Shielded; 18 AWG* (recommended)
Non Plenum - Belden 9461; Plenum - Belden 88761
1000 ft. (300m) N/A
Port S2 EIA-232
18-22 AWG Stranded & Shielded; 18 AWG* (recommended)
Non Plenum - Belden 9461; Plenum - Belden 88761
50 ft. (15m) N/A
Quantity Part # Description
SiteTPI-E SiteScan Web Third-Party Interface Module - Ethernet Ready
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Emerson SITETPI-E V3 User manual

Emerson
Brand
Emerson
Model
SITETPI-E V3
Category
Power supply units
Type
User manual

Emerson SITETPI-E V3 is an Ethernet-ready device designed to interface specifically with a SiteScan Web system. It is a 32-bit microprocessor-based device designed to monitor third-party equipment via an EIA-485/232 Modbus interface. Logically, the device sits on the Ethernet network, providing the interface to SiteScan Web. This effectively creates a router/gateway and third-party interface in a single device. Screw terminal blocks are provided to terminate power, communication, and input signal wiring.

Some of the key capabilities of the Emerson SITETPI-E V3 include:

  • Ethernet connectivity: The device can be connected to an Ethernet network, allowing it to communicate with other devices on the network, including the SiteScan Web system.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents