Delta 50-762 User manual

Brand: Delta

Model: 50-762

Category: Power tools

Type: User manual

This manual is also suitable for

50-763

www.deltamachinery.com

(800) 223-7278 - US

(800) 463-3582 - CANADA

Instruction Manual

Manuel d’Utilisation

Manual de Instrucciones

50-762

50-763

FRANÇAIS (15) ESPAÑOL (29)

A16999 - 04-28-06

Recolector de

polvo de 3 H.P.

3 H.P.

Dépoussiéreur

3 H.P. Dust

Collector

TABLE OF CONTENTS

Read and understand all warnings and operating instructions before using any tool or equipment.

When using tools or equipment, basic safety precautions should always be followed to reduce the risk of

personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious

injury and property damage. There are certain applications for which tools and equipment are designed. Delta

Machinery strongly recommends that this product NOT be modified and/or used for any application other than

for which it was designed.

If you have any questions relative to its application, DO NOT use the product until you have written Delta Machinery

and we have advised you.

Online contact form at www.deltamachinery.com

Postal Mail: Technical Service Manager

Delta Machinery

4825 Highway 45 North

Jackson, TN 38305

(IN CANADA: 125 Mural St. Suite 300, Richmond Hill, ON, L4B 1M4)

Information regarding the safe and proper operation of this tool is available from the following sources:

Power Tool Institute

1300 Sumner Avenue, Cleveland, OH 44115-2851

www.powertoolinstitute.org

National Safety Council

1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org

ANSI 01.1Safety Requirements for Woodworking Machines, and the U.S. Department of Labor regulations www.osha.gov

SAVE THESE INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY GUIDELINES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

CARTON CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

ESPAÑOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially haz ard ous situation which, if not avoided, may result in minor or mod er ate injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may

result in property damage.

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR

SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

SAFETY GUIDELINES - DEFINITIONS

TOOL WARNING LABEL

WHEN USING THIS DUST COLLECTOR, DO NOT PICK UP ANYTHING THAT IS BURNING, SMOL-

DERING OR SMOKING, SUCH AS MATCHES, CIGARETTES, OR HOT ASHES.

DO NOT USE TO VACUUM COMBUSTIBLE EXPLOSIVE MATERIALS, SUCH AS COAL, GRAIN OR

OTHER FINELY DIVIDED COMBUSTIBLE MATERIAL.

DO NOT USE TO VACUUM HAZARDOUS, TOXIC, OR CARCINOGENIC MATERIALS SUCH AS

ASBESTOS, PESTICIDE OR LEAD-BASED PAINT DEBRIS.

1. FOR YOUR OWN SAFETY, READ THE INSTRUCTION

MANUAL BEFORE OPERATING THE MACHINE. Learning

the machine’s application, limitations, and specific hazards

will greatly minimize the possibility of accidents and injury.

2. WEAR EYE AND HEARING PROTECTION. ALWAYS

USE SAFETY GLASSES. Everyday eyeglasses are NOT

safety glasses. USE CERTIFIED SAFETY EQUIPMENT.

Eye protection equipment should comply with ANSI Z87.1

standards. Hearing equipment should comply with ANSI

S3.19 standards.

3. WEAR PROPER APPAREL. Do not wear loose clothing,

gloves, neckties, rings, bracelets, or other jewelry which may

get caught in moving parts. Nonslip protective footwear is

recommended. Wear protective hair covering to contain long

hair.

4. DO NOT USE THE MACHINE IN A DANGEROUS

ENVIRONMENT. The use of power tools in damp or wet

locations or in rain can cause shock or electrocution. Keep

your work area well-lit to prevent tripping or placing arms,

hands, and fingers in danger.

5. MAINTAIN ALL TOOLS AND MACHINES IN PEAK

CONDITION. Keep tools sharp and clean for best and safest

performance. Follow instructions for lubricating and changing

accessories. Poorly maintained tools and machines can further

damage the tool or machine and/or cause injury.

6. CHECK FOR DAMAGED PARTS. Before using the machine,

check for any damaged parts. Check for alignment of moving

parts, binding of moving parts, breakage of parts, and any

other conditions that may affect its operation. A guard or any

other part that is damaged should be properly repaired or

replaced with Delta or factory authorized replacement

parts. Damaged parts can cause further damage to the

machine and/or injury.

7. KEEP THE WORK AREA CLEAN. Cluttered areas and benches

invite accidents.

8. KEEP CHILDREN AND VISITORS AWAY. Your shop is a

potentially dangerous environment. Children and visitors can be

injured.

9. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make

sure that the switch is in the “OFF” position before plugging

in the power cord. In the event of a power failure, move the

switch to the “OFF” position. An accidental start-up can cause

injury. Do not touch the plug’s metal prongs when unplugging

or plugging in the cord.

10. USE THE GUARDS. Check to see that all guards are in place,

secured, and working correctly to prevent injury.

11. REMOVE ADJUSTING KEYS AND WRENCHES BEFORE

STARTING THE MACHINE. Tools, scrap pieces, and other

debris can be thrown at high speed, causing injury.

12. USE THE RIGHT MACHINE. Don’t force a machine or an

attachment to do a job for which it was not designed. Damage

to the machine and/or injury may result.

13. USE RECOMMENDED ACCESSORIES. The use of

accessories and attachments not recommended by Delta

may cause damage to the machine or injury to the user.

14. USE THE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. When using an extension

cord, be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a drop

in line voltage, resulting in loss of power and overheating. See

the Extension Cord Chart for the correct size depending on

the cord length and nameplate ampere rating. If in doubt, use

the next heavier gauge. The smaller the gauge number, the

heavier the cord.

15. SECURE THE WORKPIECE. Use clamps or a vise to hold the

workpiece when practical. Loss of control of a workpiece can

cause injury.

16. FEED THE WORKPIECE AGAINST THE DIRECTION OF

THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE

SURFACE. Feeding it from the other direction will cause the

workpiece to be thrown out at high speed.

17. DON’T FORCE THE WORKPIECE ON THE MACHINE.

Damage to the machine and/or injury may result.

18. DON’T OVERREACH. Loss of balance can make you fall into

a working machine, causing injury.

19. NEVER STAND ON THE MACHINE. Injury could occur if the tool

tips, or if you accidentally contact the cutting tool.

20. NEVER LEAVE THE MACHINE RUNNING UNATTENDED.

TURN THE POWER OFF. Don’t leave the machine until it comes

to a complete stop. A child or visitor could be injured.

21. TURN THE MACHINE “OFF”, AND DISCONNECT THE

MACHINE FROM THE POWER SOURCE before installing or

removing accessories, changing cutters, adjusting or changing

set-ups. When making repairs, be sure to lock the start switch

in the “OFF” position. An accidental start-up can cause injury.

22. MAKE YOUR WORKSHOP CHILDPROOF WITH

PADLOCKS, MASTER SWITCHES, OR BY REMOVING

STARTER KEYS. The accidental start-up of a machine by a

child or visitor could cause injury.

. STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE

COMMON SENSE. DO NOT USE THE MACHINE WHEN

YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS,

ALCOHOL, OR MEDICATION. A moment of inattention while

operating power tools may result in injury.

24. USE OF THIS TOOL CAN GENERATE AND

DISBURSE DUST OR OTHER AIRBORNE PARTICLES,

INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST

AND ASBESTOS DUST. Direct particles away from face

and body. Always operate tool in well ventilated area and

provide for proper dust removal. Use dust collection system

wherever possible. Exposure to the dust may cause serious

and permanent respiratory or other injury, including silicosis (a

serious lung disease), cancer, and death. Avoid breathing the

dust, and avoid prolonged contact with dust. Allowing dust to

get into your mouth or eyes, or lay on your skin may promote

absorption of harmful material. Always use properly fitting

NIOSH/OSHA approved respiratory protection appropriate for

the dust exposure, and wash exposed areas with soap and

water.

GENERAL SAFETY RULES

Failure to follow these rules may result in serious personal injury.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

DO NOT USE THIS UNIT TO FILTER

METAL DUST. Combining wood and

metal dust can create an explosion or

fire hazard. This unit is intended to filter

non-explosive atmospheres only.

DO NOT USE THIS UNIT TO DISSIPATE

FUMES OR SMOKE. Explosions or fire

can result. This dust collector is intended

for use where only dry airborne dust is

present. Its use should be limited to non-

explosive, non-metallic atmospheres.

1. DO NOT OPERATE THIS UNIT UNTIL IT IS

COMPLETE-LY ASSEMBLED AND INSTALLED

ACCORDING TO THE INSTRUCTIONS. A unit

incorrectly assembled can cause injury.

2. OBTAIN ADVICE FROM YOUR SUPERVISOR,

IN-STRUCTOR, OR ANOTHER QUALIFIED

PERSON if you are not thoroughly familiar with the

operation of this unit. Knowledge is safety

3. FOLLOW ALL WIRING CODES and recommended

electrical connections to prevent electrical shock

or electrocution.

4. DO NOT PULL THIS UNIT BY THE POWER

CORD. Do not allow the power cord to come

in contact with sharp instruments or edges, hot

surfaces, or oil or grease. Do not place any weight

on top of the power cord. A damaged power cord

can cause electrical shock or electrocution.

5. ENSURE THAT THE INTAKE AND EXHAUST

AREAS ARE CLEAR PRIOR TO STARTING THE

UNIT. Clogged intakes or exhausts can cause an

explosion and/or fire.

6. DO NOT USE THE DUST COLLECTOR to pick

up flammable liquids such as gasoline. Do not use

the dust collector near flammable or combustible

liquids. Explosion and/or fire can occur.

7. KEEP ARMS, HANDS, AND FINGERS AWAY

FROM THE FAN. Avoid all exposure to rotating

parts to prevent injury.

8. DO NOT OPERATE THIS UNIT WITHOUT THE DUST

COLLECTION BAG IN PLACE AND PROPERLY

SECURED. Sawdust and other debris can provide the

potential for fire and/or explosion and can also cause

inhalation problems.

9. INSPECT THE DUST BAG FOR CUTS, RIPS, OR

TEARS. Replace damaged bags or vacuum hoses.

Sawdust and other debris can provide the potential

for fire and/or explosion and can also cause inhalation

problems.

10. ALWAYS USE THE INTAKE CAPS TO COVER

UNUSED DUST PORTS. Debris can cause damage

to the unit and injury.

11. DO NOT ATTEMPT TO REMOVE OR REPLACE

the dust collection bag(s) while the unit is connected

to the power source. Exposed fan blades can cause

severe injuries.

12. MAINTAIN THE UNIT IN TOP CONDITION.

Clogged filters can increase the potential for fire or

explosion. Follow all instructions for changing and

cleaning filters.

13. STORE THIS UNIT IN A LOCATION that eliminates

the potential for damage to the power cord.

A damaged power cord can cause shock or

electrocution. Safely store power cord on the unit

to eliminate tripping hazards.

14. TURN THE UNIT “OFF” AND DISCONNECT THE

UNIT from the power source before installing or

removing accessories, before adjusting or changing

set-ups, or when making repairs. An accidental

start-up can cause serious injury.

15. TURN THE UNIT “OFF”, disconnect the unit from

the power source, and clean the table/work area

before leaving the area.

Failure to follow these rules may result in serious personal injury.

ADDITIONAL SPECIFIC SAFETY RULES

POWER CONNECTIONS

A separate electrical circuit should be used for your machine. This circuit should not be less than #12 wire and

should be protected with a 20 Amp time lag fuse. Before connecting the machine to the power line, make sure the

electric current is of the same characteristics as indicated on the machine's specification plate. All line connections

should make good contact. Running on low voltage will damage the machine.

Do not expose the machine to rain or operate the machine in damp locations.

MOTOR SPECIFICATIONS

The 50-762 is wired to run on 230 volts, 60 HZ, but it can also be reconfigured to run on 460 volts. The 50-763 is

wired for 230 volts, 60 HZ.

This machine must be grounded while in use to protect the operator from electric shock.

The 50-762 and 50-763 dust collectors do not come with power cords and must be permanently connected to the

building’s electrical system and grounded according to the National Electrical Code. You CANNOT use extension cords

with these three-phase machines. For instructions on how to wire three-phase or single-phase motors, check the

section “SINGLE- AND THREE-PHASE WIRING” in this manual.

460 VOLT OPERATION

460 volt operation of the 50-762 requires replacement of the motor starter and reconfiguration of the motor's internal

connections. A 460 volt starter is available from most industrial electrical supply dealers and must be installed by a

qualified electrician.

DO NOT ATTEMPT to wire the machine for 460 volts without replacing the starter. Doing so will cause

damage to the machine and personal injury could result.

FOREWORD

The Delta Industrial Dust collectors, Models 50-762 and 50-763, connect to woodworking machines that accept a 4"

diameter hose. The units each come with four 6 mil plastic collection bags and two 1-micron cloth filter bags. The 50-

762 has a three-phase 230V/460V 3HP motor, while the 50-763 has a single-phase 230V 3HP motor.

FUNCTIONAL DESCRIPTION

1. Motor and Blower Assembly

2. Stand

CARTON CONTENTS

7. Legs (2)

8. Bag Retainer Clamp (2)

9. Bag Hanging Rod (2)

10. Caster (4)

11. Intake Cap and Ring (4)

12. Knob for Blower/Motor Assembly (4)

3. Dust Intake Port

4. Cloth-covered Bag-retainer Ring (2)

5. One-Micron Upper Filter Bags (2)

6. Six-mil Plastic Lower Collection Bag (4)

13. 3/8” (9.5mm) Flat Washer for Knobs (4)

14. 5/16” (8mm) Flat Washers for Casters (16)

15. M4 Sheet Metal Screw for Dust Intake Port (4)

16. Bracket for Bag-hanging Rod (2)

17. 5/16” x 3/4” Hex-Head Screws (22) ( 6 are for attaching the bracket )

18. 5/16” (8mm) Flat Washer for Bracket (6)

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the rust-preventative oil from

unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol.

Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning your

machine.

After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

ASSEMBLY

For your own safety, do not connect the machine to the power source until the machine is

completely assembled and you read and understand the entire instruction manual.

ASSEMBLY TOOLS REQUIRED

ASSEMBLY TIME ESTIMATE

Phillips head screwdriver 12 mm wrench

This machine is heavy. Use two or more people when lifting.

1. Turn the stand (A) upside down (Fig 1).

2. Align the holes in the caster assembly (B) with the

holes in the plates on the stand. Place a 5/16”

flatwasher on a 5/16” x 3/4” hex-head screw. Place

this screw through the hole in the caster assembly.

and thread it into the hole in the stand. Attach the

other caster assemblies in the same manner.

3. Tighten the hardware by hand and then set it with

a 12mm wrench.

NOTE: This step requires two people.

Place all four stand posts (A) Fig. 3 into the four legs

(B) on the motor/blower assembly. Make sure that the

metal base plates (D) are arranged over the large holes

in the dust collector (C).

1. Place the motor/blower assembly with the motor (A)

Fig. 2 down.

2. Place a 3/8” (18 mm) flatwasher on the knob (B).

3. Align the holes on the legs (C) with the holes (D) in

the motor/blower assembly with the legs extending

up. Insert the knob through the hole in the legs

assembly (D). Tighten the knob securely.

4. Repeat for all knobs on both legs.

ATTACHING THE LEGS ON THE MOTOR/BLOWER ASSEMBLY

ATTACHING THE CASTERS

ATTACHING THE STAND TO THE LEGS ON THE MOTOR/BLOWER ASSEMBLY

30 minutes to 1 hour

Fig. 1

Fig. 2

Fig. 3

Place the dust intake port (A) Fig. 7 over the intake hole

(B) opposite the motor. Align the four holes (C) (two of

which are shown) in the port with the ones in the motor/

blower assembly (D). Fasten them with four M4 sheet

metal screws.

Turn the unit over so that the casters are on the

ground.

Because of the weight of the unit, use

more than one person to place it into the upright

position.

The previous instructions have shown how to assemble the unit with the motor on top and dust intake ports on bottom

(Fig 4).

You can also assemble this unit with the intake port (B) Fig. 5 in the up position by following the steps in “ATTACHING

THE LEGS TO THE MOTOR/BLOWER ASSEMBLY.” The difference in assembly is in placing the motor/blower

assembly on a flat surface with the motor (A) Fig. 5 facing up, and attaching the legs in that position.

NOTE: Before using the alternate set-up, remove the 5/16” hex head screws from holes (B) Fig. 6 in the motor/blower

assembly and place them in the holes (C). Air will leak if the screws are left out of these holes.

Disconnect the machine from the power source!

ALTERNATE SET-UP

Fig. 4

Fig. 7

Fig. 6

Fig. 5

ATTACHING THE DUST INTAKE PORTS

1. Place the cloth-covered bag retainer ring (A) Fig. 8 inside the opening of the clear plastic dust collection bag.

Fold about 6 inches of the bag around the retainer ring.

2. Place the bag in the large hole (B) Fig. 8 in the motor/blower assembly. Fit the retainer ring (A) Fig. 8 and (A)

Fig. 9 into the bottom groove (B) Fig. 9. Bend and fold the ring to fit it into place.

3. Tug slightly on the bag to eliminate any slack and to make sure that the bag is secure and will not detach

during collection.

4. Repeat for the other bag.

B. USING A METAL BAG CLAMP

You can also attach the plastic bag to the outside of the dust collector using the included clamp (B) Fig. 10:

1. Place the clamp (B) around the top of the plastic bag (A). Fold about 4 to 6 inches of plastic bag over the

clamp (Fig. 10).

2. Place the clamp and plastic bag (A) Fig. 11 on the blower assembly. Fasten the clamp (B) securely.

3. Repeat for the other bag.

ATTACHING A DUST COLLECTION BAG

Disconnect the machine from the power source!

A. USING A CLOTH COVERED FLEXIBLE RING

ATTACHING THE TOP FILTER BAG

1. Place a 5/16” flatwasher on a 5/16" hex head

screw.

2. Position the bracket (A) on the dust collector (Fig.

12).

3. Insert a 5/16" hex head screw through a hole in the

bracket, then thread it into the appropriate hole in

the dust collector.

4. Thread the other two screws into the other holes

and tighten all three screws securely with the 12mm

wrench.

Fig. 8

Fig. 9

Fig. 10

Fig. 11

Fig. 12

Disconnect the machine from the power source!

5. Insert the rod into the pocket on the filter bag (A) Fig.

13.

6. Insert the rod in the hole in the bracket (B).

7. Work the open end of the filter bag into the top

groove of the dust collector drum until it is secure

and sealed. Bend and fold, as necessary, the internal

bag retainer ring to fit it into place.

8. Attach the other filter bag in the same manner.

Models 50-762/50-763 provide four 4” dust ports.

NOTE: Place the intake cap rings (D) Fig. 14 on the ends

of each dust intake port before attaching the hose.

Loosely place a hose clamp (A) Fig. 14 around one end

of the flexible hose (B). Attach the hose to the dust

intake port (C). Tighten the hose clamp (A). Attach the

remaining clamp to the other end of the flexible hose

and to the woodworking machine.

NOTE: Do not operate the dust collector with any of the

holes in dust intake port (C) Fig. 14 uncovered. To cover

a hole not being used by a hose, place the flat intake

cap (E) on dust intake port as shown in Fig. 14.

ATTACHING THE ACCESSORY HOSE TO THE INTAKE PORT

Disconnect the machine from the power source!

SINGLE- AND THREE-PHASE WIRING

Use a qualified electrician to install this machine to ensure safe and proper wiring and product

operation.

DIsconnect power at source before wiring the machine.

Your dust collector must be permanently connected to

the building’s electrical system and grounded to meet

code.

1. To connect the dust collector to a power system,

remove the controller cover (A) Fig. 15.

2. Bring the three-phase power line through the access

hole (B) Fig. 15 in the bottom of controller box.

MODEL 50-762 THREE PHASE INSTALLATION (230 VOLT OPERATION)

Fig. 13

Fig. 14

Fig. 15

3. Connect the three power lines to terminals (C) Fig.

16, and the green ground wire to ground screw (D).

4. After connecting the power cord to the machine, view

the rotation of the blower fan to make certain that the

rotation of the motor is in the proper direction. The fan

should rotate clockwise. You can reverse the rotation

of the motor by interchanging any two of the three

incoming power lines connected to terminals (C) Fig.

16.

Disconnect the machine from the power

source before reversing the wires.

Do not insert fingers or any foreign object into the dust intake port.

Make sure that the unit is properly grounded.

Re-install the cover before operating.

Your dust collector must be permanently connected to the building’s electrical system and grounded to meet code.

MODEL 50-763 SINGLE PHASE INSTALLATION

1. Remove the controller cover (A) Fig. 17.

2. Bring the single phase power line through the access hole (B) Fig. 17 in the bottom of controller box and connect the

two power lines to terminals (E) Fig. 18, and the green ground wire to the ground screw (F).

Re-install the cover before operating.

Do not insert fingers or any foreign object into the dust intake port.

Make sure that the unit is properly grounded.

Fig. 16

Fig. 17

Fig. 18

460 VOLT OPERATION

460V operation of the 50-762 requires replacement of

the motor starter and reconfiguration of the motor's

internal connections. This item is available from most

industrial electrical supply dealers and must be installed

by a qualified electrician.

DO NOT ATTEMPT to wire the machine for

460 volts without replacing the starter. Doing so will

cause damage to the machine and personal injury

could result.

The on/off buttons (A) and (B) Fig. 19 are located on the

front of the motor housing. To turn the machine "ON",

push the "ON" button (A).

To turn the machine "OFF", push the "OFF" button (B).

STARTING AND STOPPING THE

DUST COLLECTOR

OPERATION

Fig. 19

IMPORTANT: When the machine is not in use, the

“ON” button (A) Fig. 19 should be locked to prevent

unauthorized use,

using a padlock (C) Fig. 20 with a

3/16" diameter shackle through the hole beside the

button.

LOCKING SWITCH IN THE “OFF” POSITION

When using this dust collector, do not pick up anything that is burning, smoldering, or smoking,

such as matches, cigarettes, or hot ashes.

Do not use this machine to vacuum combustible explosive materials, such as coal, grain, or

other finely-divided combustible materials.

Do not use this machine to vacuum hazardous, toxic, or carcinogenic materials, such as

asbestos, pesticide, or lead-based paint debris.

Fig. 20

TROUBLESHOOTING

For assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call the

DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).

MAINTENANCE

KEEP MACHINE CLEAN

Periodically blow out all air passages with dry compressed

air. All plastic parts should be cleaned with a soft damp

cloth. NEVER use solvents to clean plastic parts. They

could possibly dissolve or otherwise damage the material.

WEAR CERTIFIED SAFETY EQUIPMENT

FOR EYE, HEARING AND RESPIRATORY PROTECTION

WHILE USING COMPRESSED AIR.

FAILURE TO START

Should your machine fail to start, check to make sure

the prongs on the cord plug are making good contact

in the outlet. Also, check for blown fuses or open circuit

breakers in the line.

LUBRICATION & RUST PROTECTION

Apply household floor paste wax to the machine table,

extension table or other work surface weekly. Or use a

commercially available protective product designed for

this purpose. Follow the manufacturer’s instructions for

use and safety.

To clean cast iron tables of rust, you will need the

following materials: a pushblock from a jointer, a sheet

of medium Scotch-Brite™ Blending Hand Pad, a can of

WD-40

and a can of degreaser. Apply the WD-40 and

polish the table surface with the Scotch-Brite pad using

the pushblock as a holddown. Degrease the table, then

apply the protective product as described above.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our website at

servicenet.deltamachinery.com.

You can also order parts from your nearest factory-owned branch, or by calling our Customer Care Center at 1-800-223-7278 to

receive personalized support from highly-trained technicians.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about Delta Machinery, its factory-

owned branches, or an Authorized Warranty Service Center, visit our website at www.deltamachinery.com or call our Customer

Care Center at 1-800-223-7278. All repairs made by our service centers are fully guaranteed against defective material and

workmanship. We cannot guarantee repairs made or attempted by others.

You can also write to us for information at Delta Machinery, 4825 Highway 45 North, Jackson, Tennessee 38305 - Attention:

Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number,

etc.)

SERVICE

A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and

Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or for the name of

your nearest supplier.

Since accessories other than those offered by Delta have not been tested with this product, use

of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be

used with this product.

ACCESSORIES

Two Year Limited New Product Warranty

Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal

use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service

center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity

to verify the alleged defect by inspection. For all refurbished Delta product, the warranty period is 180 days. Delta may require that electric

motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible

for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone

other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for incidental or consequential

damages resulting from defective products. This warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect

to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly

disclaimed by Delta.

WARRANTY

To register your tool for warranty service visit our website at www.deltamachinery.com.

Page is loading ...

The gray & black color scheme is a trademark for Porter-Cable Power Tools and Accessories. The following are also trademarks for one or more Porter-

Cable and Delta products:  L’agencement de couleurs grise et noire est une marque de commerce des outils électriques et accessoires Porter-Cable.

Les marques suivantes sont également des marques de commerce se rapportant à un ou plusieurs produits Porter-Cable ou Delta :  El gráﬁ co de color

negro y gris es una marca registrada para las herramientas eléctricas y los accesorios Porter-Cable. Las siguientes también son marcas comerciales para

uno o más productos de Porter-Cable y Delta: 2 BY 4

, 890

™

, Air America

, AIRBOSS

™

, Auto-Set

, B.O.S.S.

, Bammer

, Biesemeyer

, Builders

Saw

, Charge Air

, Charge Air Pro

, CONTRACTOR SUPERDUTY

, Contractor's Saw

, Delta

, DELTA

, Delta Industrial

, DELTA MACHINERY &

DESIGN

™

, Delta Shopmaster and Design

, Delta X5

, Deltacraft

, DELTAGRAM

, Do It. Feel It.

, DUAL LASERLOC AND DESIGN

, EASY AIR

EASY AIR TO GO

™

, ENDURADIAMOND

, Ex-Cell

, Front Bevel Lock

, Get Yours While the Sun Shines

, Grip to Fit

, GRIPVAC

™

, GTF

, HICKORY

WOODWORKING

, Homecraft

, HP FRAMER HIGH PRESSURE

, IMPACT SERIES

™

, Innovation That Works

, Jet-Lock

, Job Boss

, Kickstand

LASERLOC

, LONG-LASTING WORK LIFE

, MAX FORCE

™

, MAX LIFE

, Micro-Set

, Midi-Lathe

, Monsoon

, MONSTER-CARBIDE

™

, Network

OLDHAM

, Omnijig

, PC EDGE

, Performance Crew

™

, Performance Gear

, Pocket Cutter

, Porta-Band

Porta-Plane

, Porter Cable

, Porter-

Cable Professional Power Tools

, Powerback

, POZI-STOP

™

, Pressure Wave

, PRO 4000

, Proair

, Quicksand and Design

, Quickset II

, QUIET

DRIVE TECHNOLOGY

™

, QUIET DRIVE TECHNOLOGY AND DESIGN

™

, Quik-Change

, QUIK-TILT

, RAPID-RELEASE

™

, RAZOR

, Redeﬁ ning

Performance

, Riptide

, Safe Guard II

, Sand Trap and Design

, Sanding Center

, Saw Boss

, Shop Boss

, Sidekick

, Site Boss

, Speed-Bloc

Speedmatic

, Stair Ease

, Steel Driver Series

, SUPERDUTY

, T4 & DESIGN

, THE AMERICAN WOODSHOP

, THE PROFESSIONAL EDGE

Thin-Line

, Tiger Saw

, TIGERCLAW

, TIGERCLAW AND DESIGN

, Torq-Buster

, TRU-MATCH

, T-Square

, Twinlaser

, Unifence

, Uniguard

UNIRIP

, UNISAW

, UNITED STATES SAW

®,

Veri-Set

, Versa-Feeder

, VIPER

, VT

™

, VT RAZOR

™,

Water Driver

, WATER VROOM

, Waveform

Whisper Series

, X5

, YOUR ACHIEVEMENT. OUR TOOLS.

Trademarks noted with ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Other trademarks

may apply.  Les marques de commerce suivies du symbole ® sont enregistrées auprès du United States Patent and Trademark Ofﬁ ce et peuvent être

enregistrées dans d’autres pays. D’autres marques de commerce peuvent également être applicables.  Las marcas comerciales con el símbolo ® están

registradas en la Oﬁ cina de patentes y marcas comerciales de Estados Unidos (United States Patent and Trademark Ofﬁ ce), y también pueden estar

registradas en otros países. Posiblemente se apliquen otras marcas comerciales registradas.

Delta Machinery

4825 Highway 45 North

Jackson, TN 38305

(800) 223-7278

www.deltamachinery.com