Delta 50-764 User manual

www.deltamachinery.com

(800) 223-7278 - US

(800) 463-3582 - CANADA

Recolector de

polvo de 5 H.P.

5 H.P.

Dépoussiéreur

5 H.P. Dust

Collector

Instruction Manual

Manuel d’Utilisation

Manual de Instrucciones

50-764

50-765

FRANÇAIS (17) ESPAÑOL (31)

A17000 - 04-21-06

Machinery

2

TABLE OF CONTENTS

Read and understand all warnings and operating instructions before using any tool or equipment. When

using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Im-

proper operation, maintenance or modification of tools or equipment could result in serious injury and property damage.

There are certain applications for which tools and equipment are designed. Delta Machinery strongly recommends that

this product NOT be modified and/or used for any application other than for which it was designed.

If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery

and we have advised you.

Online contact form at www.deltamachinery.com

Postal Mail: Technical Service Manager

Delta Machinery

4825 Highway 45 North

Jackson, TN 38305

Information regarding the safe and proper operation of this tool is available from the following sources:

Power Tool Institute

1300 Sumner Avenue, Cleveland, OH 44115-2851

www.powertoolinstitute.org

National Safety Council

1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org

ANSI 01.1Safety Requirements for Woodworking Machines, and

the U.S. Department of Labor regulations www.osha.gov

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY GUIDELINES - DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

TOOL WARNING LABEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

FRANÇAIS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

ESPAÑOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially haz ard ous situation which, if not avoided, may result in minor or mod er ate injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may

result in property damage.

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR

SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

SAFETY GUIDELINES - DEFINITIONS

TOOL WARNING LABEL

WHEN USING THIS DUST COLLECTOR, DO NOT PICK UP ANYTHING THAT IS BURNING, SMOL-

DERING OR SMOKING, SUCH AS MATCHES, CIGARETTES, OR HOT ASHES.

DO NOT USE TO VACUUM COMBUSTIBLE EXPLOSIVE MATERIALS, SUCH AS COAL, GRAIN OR

OTHER FINELY DIVIDED COMBUSTIBLE MATERIAL.

DO NOT USE TO VACUUM HAZARDOUS, TOXIC, OR CARCINOGENIC MATERIALS SUCH AS

ASBESTOS, PESTICIDE OR LEAD-BASED PAINT DEBRIS.

4

1. FOR YOUR OWN SAFETY, READ THE INSTRUCTION

MANUAL BEFORE OPERATING THE MACHINE. Learning

the machine’s application, limitations, and specific hazards

will greatly minimize the possibility of accidents and injury.

2. WEAR EYE AND HEARING PROTECTION. ALWAYS

USE SAFETY GLASSES. Everyday eyeglasses are NOT

safety glasses. USE CERTIFIED SAFETY EQUIPMENT.

Eye protection equipment should comply with ANSI Z87.1

standards. Hearing equipment should comply with ANSI

S3.19 standards.

3. WEAR PROPER APPAREL. Do not wear loose clothing,

gloves, neckties, rings, bracelets, or other jewelry which may

get caught in moving parts. Nonslip protective footwear is

recommended. Wear protective hair covering to contain long

hair.

4. DO NOT USE THE MACHINE IN A DANGEROUS

ENVIRONMENT. The use of power tools in damp or wet

locations or in rain can cause shock or electrocution. Keep

your work area well-lit to prevent tripping or placing arms,

hands, and fingers in danger.

5. MAINTAIN ALL TOOLS AND MACHINES IN PEAK

CONDITION. Keep tools sharp and clean for best and safest

performance. Follow instructions for lubricating and changing

accessories. Poorly maintained tools and machines can further

damage the tool or machine and/or cause injury.

6. CHECK FOR DAMAGED PARTS. Before using the machine,

check for any damaged parts. Check for alignment of moving

parts, binding of moving parts, breakage of parts, and any

other conditions that may affect its operation. A guard or any

other part that is damaged should be properly repaired or

replaced with Delta or factory authorized replacement

parts. Damaged parts can cause further damage to the

machine and/or injury.

7. KEEP THE WORK AREA CLEAN. Cluttered areas and benches

invite accidents.

8. KEEP CHILDREN AND VISITORS AWAY. Your shop is a

potentially dangerous environment. Children and visitors can be

injured.

9. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make

sure that the switch is in the “OFF” position before plugging

in the power cord. In the event of a power failure, move the

switch to the “OFF” position. An accidental start-up can cause

injury. Do not touch the plug’s metal prongs when unplugging

or plugging in the cord.

10. USE THE GUARDS. Check to see that all guards are in place,

secured, and working correctly to prevent injury.

11. REMOVE ADJUSTING KEYS AND WRENCHES BEFORE

STARTING THE MACHINE. Tools, scrap pieces, and other

debris can be thrown at high speed, causing injury.

12. USE THE RIGHT MACHINE. Don’t force a machine or an

attachment to do a job for which it was not designed. Damage

to the machine and/or injury may result.

13. USE RECOMMENDED ACCESSORIES. The use of

accessories and attachments not recommended by Delta

may cause damage to the machine or injury to the user.

14. USE THE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. When using an extension

cord, be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a drop

in line voltage, resulting in loss of power and overheating. See

the Extension Cord Chart for the correct size depending on

the cord length and nameplate ampere rating. If in doubt, use

the next heavier gauge. The smaller the gauge number, the

heavier the cord.

15. SECURE THE WORKPIECE. Use clamps or a vise to hold the

workpiece when practical. Loss of control of a workpiece can

cause injury.

16. FEED THE WORKPIECE AGAINST THE DIRECTION OF

THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE

SURFACE. Feeding it from the other direction will cause the

workpiece to be thrown out at high speed.

17. DON’T FORCE THE WORKPIECE ON THE MACHINE.

Damage to the machine and/or injury may result.

18. DON’T OVERREACH. Loss of balance can make you fall into

a working machine, causing injury.

19. NEVER STAND ON THE MACHINE. Injury could occur if the tool

tips, or if you accidentally contact the cutting tool.

20. NEVER LEAVE THE MACHINE RUNNING UNATTENDED.

TURN THE POWER OFF. Don’t leave the machine until it comes

to a complete stop. A child or visitor could be injured.

21. TURN THE MACHINE “OFF”, AND DISCONNECT THE

MACHINE FROM THE POWER SOURCE before installing or

removing accessories, changing cutters, adjusting or changing

set-ups. When making repairs, be sure to lock the start switch

in the “OFF” position. An accidental start-up can cause injury.

22. MAKE YOUR WORKSHOP CHILDPROOF WITH

PADLOCKS, MASTER SWITCHES, OR BY REMOVING

STARTER KEYS. The accidental start-up of a machine by a

child or visitor could cause injury.

23

. STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE

COMMON SENSE. DO NOT USE THE MACHINE WHEN

YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS,

ALCOHOL, OR MEDICATION. A moment of inattention while

operating power tools may result in injury.

24. USE OF THIS TOOL CAN GENERATE AND

DISBURSE DUST OR OTHER AIRBORNE PARTICLES,

INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST

AND ASBESTOS DUST. Direct particles away from face

and body. Always operate tool in well ventilated area and

provide for proper dust removal. Use dust collection system

wherever possible. Exposure to the dust may cause serious

and permanent respiratory or other injury, including silicosis (a

serious lung disease), cancer, and death. Avoid breathing the

dust, and avoid prolonged contact with dust. Allowing dust to

get into your mouth or eyes, or lay on your skin may promote

absorption of harmful material. Always use properly fitting

NIOSH/OSHA approved respiratory protection appropriate for

the dust exposure, and wash exposed areas with soap and

water.

GENERAL SAFETY RULES

Failure to follow these rules may result in serious personal injury.

5

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

DO NOT USE THIS UNIT TO FILTER

METAL DUST. Combining wood and

metal dust can create an explosion or

fire hazard. This unit is intended to filter

non-explosive atmospheres only.

DO NOT USE THIS UNIT TO DISSIPATE

FUMES OR SMOKE. Explosions or fire

can result. This dust collector is intended

for use where only dry airborne dust is

present. Its use should be limited to non-

explosive, non-metallic atmospheres.

1. DO NOT OPERATE THIS UNIT UNTIL IT IS

COMPLETE-LY ASSEMBLED AND INSTALLED

ACCORDING TO THE INSTRUCTIONS. A unit

incorrectly assembled can cause injury.

2. OBTAIN ADVICE FROM YOUR SUPERVISOR,

IN-STRUCTOR, OR ANOTHER QUALIFIED

PERSON if you are not thoroughly familiar with the

operation of this unit. Knowledge is safety

3. FOLLOW ALL WIRING CODES and recommended

electrical connections to prevent electrical shock

or electrocution.

4. DO NOT PULL THIS UNIT BY THE POWER

CORD. Do not allow the power cord to come

in contact with sharp instruments or edges, hot

surfaces, or oil or grease. Do not place any weight

on top of the power cord. A damaged power cord

can cause electrical shock or electrocution.

5. SUPPORT THIS UNIT OR SECURELY CLAMP IT

TO THE WORK SURFACE WHEN IT IS USED IN

A PORTABLE APPLICATION to eliminate potential

injury and/or damage from falling.

6. ENSURE THAT THE INTAKE AND EXHAUST

AREAS ARE CLEAR PRIOR TO STARTING THE

UNIT. Clogged intakes or exhausts can cause an

explosion and/or fire.

7. DO NOT USE THE DUST COLLECTOR to pick

up flammable liquids such as gasoline. Do not use

the dust collector near flammable or combustible

liquids. Explosion and/or fire can occur.

8. KEEP ARMS, HANDS, AND FINGERS AWAY

FROM THE FAN. Avoid all exposure to rotating

parts to prevent injury.

9. DO NOT OPERATE THIS UNIT WITHOUT THE DUST

COLLECTION BAG IN PLACE AND PROPERLY

SECURED. Sawdust and other debris can provide the

potential for fire and/or explosion and can also cause

inhalation problems.

10. INSPECT THE DUST BAG FOR CUTS, RIPS, OR

TEARS. Replace damaged bags or vacuum hoses.

Sawdust and other debris can provide the potential

for fire and/or explosion and can also cause inhalation

problems.

11. ALWAYS USE THE INTAKE CAPS TO COVER

UNUSED DUST PORTS. Debris can cause damage

to the unit and injury.

12. DO NOT ATTEMPT TO REMOVE OR REPLACE

the dust collection bag(s) while the unit is connected

to the power source. Exposed fan blades can cause

severe injuries.

13. MAINTAIN THE UNIT IN TOP CONDITION.

Clogged filters can increase the potential for fire or

explosion. Follow all instructions for changing and

cleaning filters.

14. STORE THIS UNIT IN A LOCATION that eliminates

the potential for damage to the power cord.

A damaged power cord can cause shock or

electrocution. Safely store power cord on the unit

to eliminate tripping hazards.

15. TURN THE UNIT “OFF” AND DISCONNECT THE

UNIT from the power source before installing or

removing accessories, before adjusting or changing

set-ups, or when making repairs. An accidental

start-up can cause serious injury.

16. TURN THE UNIT “OFF”, disconnect the unit from

the power source, and clean the table/work area

before leaving the area.

Failure to follow these rules may result in serious personal injury.

ADDITIONAL SPECIFIC SAFETY RULES

6

POWER CONNECTIONS

A separate electrical circuit should be used for your machine. This circuit should not be less than #12 wire and should be

protected with a 30 Amp time lag fuse. Before connecting the machine to the power line, make sure the electric current

is of the same characteristics as indicated on the machine's specification plate. All line connections should make good

contact. Running on low voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

The 50-764 is wired for 230 volts, 60HZ alternating current. The 50-764 can also be reconfigured to run on 460 volts. The

50-765 is wired for 230V, 60 HZ alternating current.

THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM

ELECTRIC SHOCK.

The 50-764 and 50-765 dust collectors are not supplied with a power cord. They must be permanently connected to the

building’s electrical system and grounded according to the National Electrical Code. Since they must be permanently

connected to the building’s electrical system, extension cords cannot be used with these dust collectors. For instructions

on how to wire three phase or single phase motors, check the section “SINGLE AND THREE PHASE WIRING” in this

manual.

460 VOLT OPERATION

460 volt operation of the 50-764 requires replacement of the motor starter and reconfiguration of the motor's internal

connections. A 460 volt starter is available from most industrial electrical supply dealers and must be installed by a

qualified electrician.

DO NOT ATTEMPT to wire the machine for 460 volts without replacing the starter. Doing so will cause damage

to the machine and personal injury could result.

FOREWORD

The Delta Industrial Models 50-764 and 50-765 are dust collectors that will connect to woodworking machines that ac-

cept a 5" diameter hose. The units each come with two 1 micron filter bags and four 6 mil plastic collection bags. The

50-764 has a three phase 230V/460V 5HP motor, while the 50-765 has a single phase 230V 5 HP motor.

FUNCTIONAL DESCRIPTION

7

3

4

5

6

7

8

9

4. Cloth-covered bag retainer ring (2)

5. One micron upper filter bag (2)

6. Six mil plastic lower bag (4)

7. Legs (2)

8. Bag retainer clamp (2)

9. Lower bag support pole (2)

10. Bag hanger assembly (2)

11. Upper bag support pole (2)

Fig. 1D

10

11

1. Motor and blower assembly

2. Stand

3. Dust intake port

1

2

Fig. 1C

CARTON CONTENTS

8

12

13

20

14

15

16

17

18

Fig. 1E

19

21

12. Caster (4)

13. Intake cap and ring (4)

14. Knob for attaching legs to blower/motor assembly (6)

15. 3/8” (9.5mm) Flat washer for knobs (6)

16. 5/16” (9mm) Small flat washers for casters (16)

17. M4 Sheet metal screw for dust intake port (4)

18. 5/16”x3/4” Hex head screw for attaching casters to base (16)

19. 5/16” (8mm) Hex nut (2)

20. 5/16” (8mm) x 1

1

/4” Hex head screw for bag hanger assembly (2)

21. 5/16” (8mm) Large washers for bag hanger assembly (2)

22. 3/8” washer for bag hanger assembly (2)

ASSEMBLY

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the rust-preventative oil from

unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol.

Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning your

machine.

After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

ASSEMBLY TOOLS REQUIRED

Phillips head screwdriver

12 mm wrench

ASSEMBLY TIME ESTIMATE

Assembly for this machine takes approximately 1-2 hours.

9

FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL

THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION

MANUAL.

CASTERS

1. Turn stand (A) upside down, as shown in Fig 1F.

2. Align holes in caster assembly (B) with holes in

plates on stand. Place small 5/16” flatwasher on a

5/16”x3/4” hex head screw. Insert screw through

hole in caster assembly and thread into hole in

stand. Repeat for all holes in all casters.

3. Tighten hardware by hand, then set with a 12mm

wrench.

LEGS TO MOTOR/BLOWER

ASSEMBLY

1. Place motor/blower assembly with the motor down.

(Fig. 2)

2. Place 3/8” (18 mm) flatwasher on knob (A) Fig. 2.

3. Align holes (B) on legs with holes (C) in the mo-

tor/blower assembly. Legs should extend up. Insert

knob through hole (B) in the legs and thread into

hole (C) in the motor/blower assembly. Tighten

knob securely.

4. Repeat steps for all knobs on both legs.

Fig. 1F

Fig. 2

ATTACHING STAND TO LEGS ON

MOTOR/BLOWER ASSEMBLY

NOTE: TWO PEOPLE ARE NEEDED FOR THIS STEP.

Place all four stand posts (A) Fig. 3 into four legs (B) on

motor/blower assembly.

Fig. 3

A

B

D

C

B

A

THIS MACHINE IS HEAVY. USE TWO

OR MORE PEOPLE WHEN LIFTING.

C

A

B

10

ALTERNATE SETUP

The steps so far will assemble the unit with the motor

on top and dust intake ports on bottom, as shown in

Fig 4.

This unit can be assembled with the intake port (A) Fig.

5 in the up position by following the steps in “LEGS TO

MOTOR/BLOWER ASSEMBLY.” The exception is to

place the motor/blower assembly on a flat surface with

the motor (A) Fig. 6 facing up before attaching legs.

NOTE: BEFORE DOING THE ALTERNATE SETUP,

REMOVE 5/16” HEX HEAD SCREWS FROM HOLES (B)

FIG. 6 IN MOTOR/BLOWER ASSEMBLY AND PLACE

IN HOLES (C). AIR LEAKAGE WOULD OCCUR IF

SCREWS ARE NOT PLACED IN HOLES (C).

Fig. 5

Fig. 4

ATTACHING DUST INTAKE PORTS

DISCONNECT MACHINE FROM POWER

SOURCE

Place dust intake port (A) Fig. 7 over intake hole (B) op-

posite the motor. Align four holes (C) in the port with the

ones in the motor/blower assembly and fasten with four

M4 sheet metal screws.

Turn unit over so casters are on the ground.

BECAUSE OF THE WEIGHT OF THE

UNIT, MORE THAN ONE PERSON

SHOULD LIFT MOTOR/BLOWER ASSEMBLY INTO

UPRIGHT POSITION.

A

B

Fig. 7

A

B

C

Fig. 6

C

A

11

A

Fig. 8

Fig. 9

B

Fig. 10

Fig. 10A

A

B

A

B

A

ATTACHING DUST COLLECTION BAG

USING CLOTH COVERED FLEXIBLE RING:

1. Take cloth-covered bag retainer ring (A) Fig. 8 and

place it inside opening of clear plastic dust col-

lection bag. Fold about 6 inches of the bag down

around the retainer ring.

2. Place bag up into the motor/blower assembly (B)

Fig. 8 and fit retainer ring (A) Fig. 8 and (A) Fig. 9

into bottom groove (B) Fig. 9. It will be necessary to

bend and fold the ring to fit it into place.

3. Tug slightly on bag to eliminate any slack and to

make sure there is a good fit so the bag will not

detach during collection.

4. Repeat for other bag.

USING METAL BAG CLAMP:

The plastic bag can also be attached to the outside of

the dust collector using the included clamp (B) Fig. 10:

1. Place clamp (B) around top of plastic bag (A) and

fold about 4 to 6 inches of plastic bag over the

clamp as show in Fig. 10.

2. Place the clamp and plastic bag assembly (A) Fig.

10A and fasten clamp securely as shown.

3. Repeat for other bag.

DISCONNECT MACHINE FROM

POWER SOURCE

12

Fig. 11

Fig. 12

ATTACHING TOP FILTER BAGS

DISCONNECT MACHINE FROM POWER

SOURCE

NOTE: TWO PEOPLE ARE NEEDED FOR THIS STEP.

1. Assemble upper (A) and lower (B) bag hanging rods

as shown in Fig. 11.

2. Place 3/8” flat washer on 5/16”x1 1/4” hex head

screw. Insert the screw through hole in center of

bag hanging assembly (A) Fig. 12 and Fig. 12A and

through the hole in the upper bag hanging rod (B)

Fig. 12. Then place another large 5/16” flat washer

on end of screw followed by a 5/16 hex nut. Assem-

bly shown complete in Fig. 12. Tighten all securely

with 12mm wrench.

3. Hang bag loops (C) Fig. 12A around hooks on bag

hanging assembly (B), as shown in Fig. 12A

4. Insert rod (A) Fig. 12B into hole in bracket (B). Make

sure the four bag ends are not twisted.

5. Work open end of filter bag into top groove of dust

collector drum until secure and sealed. (Similar to

how internal ring of bottom bag was inserted, Fig. 9.

It will be necessary to bend and fold the internal bag

retainer ring to fit it into place.

6. Fig. 12C shows the bags installed properly.

7. Repeat steps for the other bag.

A

B

Fig. 12A

B

A

C

B

A

B

Fig. 12B

Fig. 12C

A

13

A

B

Fig. 13

A

B

C

D

ATTACHING ACCESSORY HOSE

TO INTAKE PORT

DISCONNECT MACHINE FROM POWER

SOURCE BEFORE CONNECTING OR

DISCONNECTING HOSE .

Models 50-764/50-765 provides four 5” dust ports. Pro-

ceed as follows for each port with your accessory hos-

es.

NOTE: Place open end (D) of intake cap rings around

and onto ends of each dust intake port before attaching

the hose.

To assemble the 5” dust collection hose (not included)

to the motor and blower assembly, loosely attach hose

clamp (A) Fig. 13, around one end of flexible hose (B)

and assemble the hose to dust intake port (C). Tighten

hose clamp (A). Assemble the remaining clamp to the

other end of the flexible hose and to the woodworking

machine.

NOTE: See “ACCESORIES” section of this manual.

NOTE: Do not operate the dust collector with any of the

holes in dust intake port (C) Fig. 13 uncovered. To cover

a hole not being used by a hose, place the flat intake cap

(E) on dust intake port as shown in Fig. 13.

E

MODEL 50-764 THREE

PHASE INSTALLATION FOR 230 VOLTS

Your dust collector is supplied with a motor and a mag-

netic starter controller and must be permanently con-

nected to the building’s electrical system and grounded

to meet code.

1. To connect the dust collector to a power system, re-

move controller cover (A) Fig. 14.

2. Bring three phase power line through the access

hole (B) Fig. 14, in the top of controller box and con-

nect the three power lines to terminals (C) Fig. 15,

and the green ground wire to ground screw (D).

BE SURE TO REINSTALL COVER BE-

FORE OPERATING.

DO NOT INSERT FINGERS OR ANY FOR-

EIGN OBJECT INTO THE DUST INTAKE PORT.

MAKE SURE UNIT IS PROPERLY

GROUNDED.

SINGLE AND THREE PHASE WIRING

INSTALLATION BY A QUALIFIED ELECTRICIAN IS RECOMMENDED TO ASSURE SAFE AND PROP-

ER WIRING AND PRODUCT OPERATION.

DISCONNECT POWER AT SOURCE BE-

FORE WIRING THE MACHINE.

Fig. 14

A

B

Model 50-765

Model 50-764

14

Fig. 15

D

F

E

MODEL 50-765 SINGLE

PHASE INSTALLATION

Your dust collector is supplied with a motor and a mag-

netic starter controller and must be permanently con-

nected to the building’s electrical system and grounded

to meet code.

1. To connect the dust collector to a power system, re-

move controller cover (A) Fig. 14.

2. Bring the single phase power line through the access

hole (B) Fig. 14, in the top of controller box and con-

nect the two power lines to terminals (E) Fig. 16, and

the green ground wire to ground screw (F).

BE SURE TO REINSTALL COVER BE-

FORE OPERATING.

DO NOT INSERT FINGERS OR ANY

FOREIGN OBJECT INTO THE DUST

INTAKE PORT.

MAKE SURE UNIT IS PROPERLY

GROUNDED.

Fig. 16

3. After connecting the power cord to the machine, make

certain the rotation of the motor is in the proper direc-

tion by viewing the rotation of the blower fan. The

fan should rotate in a clockwise direction. Rotation

of the motor can be reversed by interchanging any

two of the three incoming power lines connected to

terminals (C) Fig. 15.

BE SURE TO DISCONNECT MACHINE AT

POWER SOURCE BEFORE REVERSING WIRES.

460 VOLT OPERATION

460V operation of the 50-764 requires replacement of the

motor starter and reconfiguration of the motor's internal

connections. This item is available from most industrial

electrical supply dealers and must be installed by a

qualified electrician.

DO NOT ATTEMPT TO WIRE THE MACHINE

FOR 460 VOLTS WITHOUT REPLACING THE STARTER.

DOING SO WILL CAUSE DAMAGE TO THE MACHINE

AND PERSONAL INJURY COULD RESULT.

C

FOR OPERATOR SAFETY, DO NOT OPERATE THE MACHINE WITH ANY DUST INTAKE HOLES

UNCOVERED. THE ROTATING FAN LOCATED INSIDE THE BLOWER HOUSING IS ACCESSIBLE

THROUGH THE DUST IN-TAKE PORT AND CAN BE HAZARDOUS. ALWAYS WEAR PROPER APPAREL. DO NOT

WEAR JEWELRY AND KEEP FINGERS AND ALL FOREIGN OBJECTS OUT OF THE DUST INTAKE PORT. FOLLOW

THE SAFETY RULES IN THIS MANUAL.

OPERATION

STARTING AND STOPPING DUST

COLLECTOR

1. The on (A) and off (B) buttons are located on the front

of the motor housing as shown in Fig. 17. To turn the

machine “ON”, push the “ON” button (A).

2. To turn the machine “OFF”, push the off button (B).

A

B

Fig. 17

A

B

Model 50-765

Model 50-764

15

LOCKING POWER OUT FOR 50-765

THE POWER SWITCH FOR THE 50-765

CAN NOT BE LOCKED IN THE OFF POSITION AND

SHOULD BE LOCKED OUT AT THE POWER SOURCE

TO PREVENT UNAUTHORIZED USE.

TROUBLESHOOTING GUIDE

For assistance with your tool, visit our website at www.deltamachinery.com for a list of service centers or call the

DELTA Machniery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).

WHEN USING THIS DUST COLLECTOR, DO NOT PICK UP ANYTHING THAT IS BURNING,

SMOLDERING OR SMOKING, SUCH AS MATCHES, CIGARETTES, OR HOT ASHES.

DO NOT USE TO VACUUM COMBUSTIBLE EXPLOSIVE MATERIALS, SUCH AS COAL, GRAIN

OR OTHER FINELY DIVIDED COMBUSTIBLE MATERIAL.

DO NOT USE TO VACUUM HAZARDOUS, TOXIC, OR CARCINOGENIC MATERIALS SUCH AS

ASBESTOS, PESTICIDE OR LEAD-BASED PAINT DEBRIS.

LOCKING SWITCH IN “OFF”

POSITION FOR 50-764

IMPORTANT: When the machine is not in use, the “ON”

button (A) Fig. 17 should be locked to prevent unauthor-

ized use,

using a padlock (C) Fig. 18 with a 3/16" diam-

eter shackle through the hole beside the button.

Fig. 18

C

MAINTENANCE

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to

order parts, visit our website at

servicenet.deltamachinery.

com.

You can also order parts from your nearest factory-

owned branch, or by calling our Customer Care Center at

1-800-223-7278 to receive personalized support from highly-

trained technicians.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or

replacement of parts. For information about Delta Machinery,

its factory-owned branches, or an Authorized Warranty

KEEP MACHINE CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp

cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air.

FAILURE TO START

Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the

outlet. Also, check for blown fuses or open circuit breakers in the line.

SERVICE

Service Center, visit our website at www.deltamachinery.

com or call our Customer Care Center at 1-800-223-7278.

All repairs made by our service centers are fully guaranteed

against defective material and workmanship. We cannot

guarantee repairs made or attempted by others.

You can also write to us for information at Delta Machinery,

4825 Highway 45 North, Jackson, Tennessee 38305 -

Attention: Product Service. Be sure to include all of the

information shown on the nameplate of your tool (model

number, type, serial number, etc.)

16

A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and

Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or for the name of

your nearest supplier.

Since accessories other than those offered by Delta have not been tested with this product, use

of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be

used with this product.

ACCESSORIES

Two Year Limited New Product Warranty

Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal

use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service

center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity

to verify the alleged defect by inspection. For all refurbished Delta product, the warranty period is 180 days. Delta may require that electric

motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible

for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone

other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for incidental or consequential

damages resulting from defective products. This warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect

to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly

disclaimed by Delta.

WARRANTY

To register your tool for warranty service visit our website at www.deltamachinery.com.

Page is loading ...

48

The gray & black color scheme is a trademark for Porter-Cable Power Tools and Accessories. The following are also trademarks for one or more Porter-

Cable and Delta products: L’agencement de couleurs grise et noire est une marque de commerce des outils électriques et accessoires Porter-Cable.

Les marques suivantes sont également des marques de commerce se rapportant à un ou plusieurs produits Porter-Cable ou Delta : Á El gráﬁ co de color

negro y gris es una marca registrada para las herramientas eléctricas y los accesorios Porter-Cable. Las siguientes también son marcas comerciales para

uno o más productos de Porter-Cable y Delta: 2 BY 4

®

, 890

™

, Air America

®

, AIRBOSS

™

, Auto-Set

®

, B.O.S.S.

®

, Bammer

®

, Biesemeyer

®

, Builders

Saw

®

, Charge Air

®

, Charge Air Pro

®

, CONTRACTOR SUPERDUTY

®

, Contractor's Saw

®

, Delta

®

, DELTA

®

, Delta Industrial

®

, DELTA MACHINERY &

DESIGN

™

, Delta Shopmaster and Design

®

, Delta X5

®

, Deltacraft

®

, DELTAGRAM

®

, Do It. Feel It.

®

, DUAL LASERLOC AND DESIGN

®

, EASY AIR

®

,

EASY AIR TO GO

™

, ENDURADIAMOND

®

, Ex-Cell

®

, Front Bevel Lock

®

, Get Yours While the Sun Shines

®

, Grip to Fit

®

, GRIPVAC

™

, GTF

®

, HICKORY

WOODWORKING

®

, Homecraft

®

, HP FRAMER HIGH PRESSURE

®

, IMPACT SERIES

™

, Innovation That Works

®

, Jet-Lock

®

, Job Boss

®

, Kickstand

®

,

LASERLOC

®

, LONG-LASTING WORK LIFE

®

, MAX FORCE

™

, MAX LIFE

®

, Micro-Set

®

, Midi-Lathe

®

, Monsoon

®

, MONSTER-CARBIDE

™

, Network

®

,

OLDHAM

®

, Omnijig

®

, PC EDGE

®

, Performance Crew

™

, Performance Gear

®

, Pocket Cutter

®

, Porta-Band

®

,

Porta-Plane

®

, Porter Cable

®

, Porter-

Cable Professional Power Tools

®

, Powerback

®

, POZI-STOP

™

, Pressure Wave

®

, PRO 4000

®

, Proair

®

, Quicksand and Design

®

, Quickset II

®

, QUIET

DRIVE TECHNOLOGY

™

, QUIET DRIVE TECHNOLOGY AND DESIGN

™

, Quik-Change

®

, QUIK-TILT

®

, RAPID-RELEASE

™

, RAZOR

®

, Redeﬁ ning Per-

formance

®

, Riptide

®

, Safe Guard II

®

, Sand Trap and Design

®

, Sanding Center

®

, Saw Boss

®

, Shop Boss

®

, Sidekick

®

, Site Boss

®

, Speed-Bloc

®

,

Speedmatic

®

, Stair Ease

®

, Steel Driver Series

®

, SUPERDUTY

®

, T4 & DESIGN

®

, THE AMERICAN WOODSHOP

®

, THE PROFESSIONAL EDGE

®

,

Thin-Line

®

, Tiger Saw

®

, TIGERCLAW

®

, TIGERCLAW AND DESIGN

®

, Torq-Buster

®

, TRU-MATCH

®

, T-Square

®

, Twinlaser

®

, Unifence

®

, Uniguard

®

,

UNIRIP

®

, UNISAW

®

, UNITED STATES SAW

®,

Veri-Set

®

, Versa-Feeder

®

, VIPER

®

, VT

™

, VT RAZOR

™,

Water Driver

®

, WATER VROOM

®

, Waveform

®

,

Whisper Series

®

, X5

®

, YOUR ACHIEVEMENT. OUR TOOLS.

®

Trademarks noted with ® are registered in the United States Patent and Trademark Ofﬁ ce and may also be registered in other countries. Other trademarks

may apply. Á Les marques de commerce suivies du symbole ® sont enregistrées auprès du United States Patent and Trademark Ofﬁ ce et peuvent être

enregistrées dans d’autres pays. D’autres marques de commerce peuvent également être applicables. Á Las marcas comerciales con el símbolo ® están

registradas en la Oﬁ cina de patentes y marcas comerciales de Estados Unidos (United States Patent and Trademark Ofﬁ ce), y también pueden estar reg-

istradas en otros países. Posiblemente se apliquen otras marcas comerciales registradas.

Delta Machinery

4825 Highway 45 North

Jackson, TN 38305

(800) 223-7278

www.deltamachinery.com

Delta 50-764 User manual

This manual is also suitable for

Delta 50-764 User manual

in other languages

Related papers

Other documents