ViewSonic PJ758/PJ759/PJ760 User manual

ViewSonic

®

PJ758/PJ759/PJ760

LCD Projector

- User Guide

- Guide de l’utilisateur

- Bedienungsanleitung

- Guía del usuario

- Guida dell’utente

- Guia do usuário

- Användarhandbok

- Käyttöopas

- Руководство пользователя

- 使用手冊 (繁體)

- 使用手冊 (簡體)

- 사용자 안내서

Model No. : VS11862/VS11861/VS11822

ViewSonic

i

PJ758/PJ759/PJ760

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy, and if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modiﬁ cations not expressly approved by the party

responsible for compliance could void your authority to operate the equipment.

For Canada

• This Class B digital apparatus complies with Canadian ICES-003.

• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

CE Conformity for European Countries

The device complies with the requirements of the EEC directive 89/336/EEC as

amended by 92/31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic

compatibility”, and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to “Safety.”

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic

Equipment Directive 2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment as unsorted municipal

waste, but use the return and collection systems according to local law.

ViewSonic

ii

PJ758/PJ759/PJ760

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth. If still not clean, see “Cleaning the Display” in this guide for

further instructions.

7.

Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

devices (including ampliﬁ ers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and a

third grounding prong. The wide blade and the third prong are provided for your safety. If

the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs. Convenience

receptacles and the point where they exit from the unit. Be sure that the power outlet is

located near the unit so that it is easily accessible.

11. Only use attachments/accessories speciﬁ ed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁ ed by the

manufacturer, or sold with the unit. When a cart is used, use caution when

moving the cart/unit combination to avoid injury from tipping over.

13. Unplug this unit when unused for long periods of time.

14. Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the unit has

been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is

spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the

unit does not operate normally or has been dropped.

ViewSonic

iii

PJ758/PJ759/PJ760

Declaration of RoHS Compliance

This product has been designed and manufactured in compliance with Directive 2002/95/EC of

the European Parliament and the Council on restriction of the use of certain hazardous substances

in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the

maximum concentration values issued by the European Technical Adaptation Committee (TAC)

as shown below:

Substance

Proposed Maximum

Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr

6+

) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex of the RoHS

Directives as noted below:

Examples of exempted components are:

1. Mercury in compact ﬂ uorescent lamps not exceeding 5 mg per lamp and in other lamps not

speciﬁ cally mentioned in the Annex of RoHS Directive.

2. Lead in glass of cathode ray tubes, electronic components, ﬂ uorescent tubes, and electronic

ceramic parts (e.g. piezoelectronic devices).

3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or

more lead).

4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium

containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by

weight.

ViewSonic

iv

PJ758/PJ759/PJ760

Copyright Information

Copyright

©

ViewSonic

©

Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft

Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks

of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC

are trademarks of VESA.

PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequential damages resulting from furnishing

this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the right to

change product speciﬁ cations without notice. Information in this document may change without

notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any

purpose without prior written permission from ViewSonic Corporation.

Product Registration

To meet your future needs, and to receive any additional product information as it becomes

available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic®

Wizard CD-ROM also provides an opportunity for you to print the registration form, which you

may mail or fax to ViewSonic.

For Your Records

Product Name:

Model Number:

Document Number:

Serial Number:

Purchase Date:

PJ758/PJ759/PJ760

ViewSonic LCD Projector

VS11862/VS11861/VS11822

PJ758_PJ759_PJ760_UG_ENG Rev. 1A 03-29-07

________________________________________

Personal Identiﬁcation Number (PIN):

The lamp in this product contains mercury.

Please dispose of in accordance with local, state or federal laws.

ViewSonic

1

PJ758/PJ759/PJ760

Projector

PJ758/PJ759/PJ760

User's Manual (detailed)

Operating Guide

(1) Projector

(2) Remote control

with two AA batteries

(3) Power cord

(4) RGB cable

(5) Audio/Video cable

(6) Soft case

(7) Quick Start Guide

and ViewSonic Wizard CD

(8) Lens cover and Strap

Thank you for purchasing this projector.

WARNING ►Before using this product, please read all manuals for this

product. Be sure to read “Safety Guide” ﬁ rst. After reading them, store them in

a safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are

described below.

WARNING This symbol indicates information that, if ignored, could possibly

result in personal injury or even death due to incorrect handling.

CAUTION This symbol indicates information that, if ignored, could possibly

result in personal injury or physical damage due to incorrect

handling.



Please refer to the pages written following this symbol.

NOTE • The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted

without express written consent.

Trademark acknowledgment

• Mac is registered trademarks of Apple Computer, Inc.

• VESA and SVGA are trademarks of the Video Electronics Standard Association.

• Windows is a registered trademark of Microsoft Corporation.

All other trademarks are the properties of their respective owners.

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RGB

SEARCH

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

MENU

RESET

(1) (2) (3)

(6) (7) (8)

(4) (5)

ViewSonic

2

PJ758/PJ759/PJ760

About this manual . . . . . . . . . . 1

Content . . . . . . . . . . . . . . . . . . 2

Projector features . . . . . . . . . . 3

Preparations . . . . . . . . . . . . . . 3

Contents of package . . . . . . . . . . . . .3

Fastening the lens cover . . . . . . . . . .3

Part names . . . . . . . . . . . . . . . 4

Projector . . . . . . . . . . . . . . . . . . . . . .4

Control panel . . . . . . . . . . . . . . . . . . .5

Rear panel . . . . . . . . . . . . . . . . . . . . .5

Remote control . . . . . . . . . . . . . . . . .6

Setting up . . . . . . . . . . . . . . . . 7

Arrangement . . . . . . . . . . . . . . . . . . .7

Connecting your devices . . . . . . . . .10

Connecting power supply . . . . . . . .12

Using the security bar and slot . . . .12

Remote control . . . . . . . . . . . 13

Putting batteries . . . . . . . . . . . . . . .13

About the remote control signal . . . .13

Changing the frequency of remote

control signal

. . . . . . . . . . . . . . . . .14

Using as a

simple PC mouse & keyboard . . .14

Power on/off . . . . . . . . . . . . . 15

Turning on the power . . . . . . . . . . . .15

Turning off the power . . . . . . . . . . . .15

Operating . . . . . . . . . . . . . . . 16

Adjusting the volume . . . . . . . . . . . .16

Temporarily muting the sound . . . . .16

Selecting an input signal . . . . . . . . .16

Searching an input signal . . . . . . . .17

Selecting an aspect ratio . . . . . . . . .17

Adjusting the projector's elevator . .18

Adjusting the zoom and focus . . . . .18

Using the automatic adjustment feature

. .19

Adjusting the position . . . . . . . . . . .19

Correcting the keystone distortions

. .20

Using the magnify feature . . . . . . . .20

Freezing the screen . . . . . . . . . . . . .21

Temporarily blanking the screen . . .21

Using the menu function . . . . . . . . .22

Content

EASY MENU. . . . . . . . . . . . . . 24

ASPECT, AUTO KEYSTONE EXECUTE,

K

EYSTONE , PICTURE MODE, BRIGHTNESS,

CONTRAST, COLOR, TINT, SHARPNESS,

WHISPER, MIRROR, RESET, FILTER TIME,

LANGUAGE, G

o to Advanced Menu...

PICTURE menu . . . . . . . . . . . 26

BRIGHTNESS, CONTRAST, GAMMA, COLOR TEMP,

COLOR, TINT, SHARPNESS, MY MEMORY

IMAGE menu . . . . . . . . . . . . . 29

ASPECT, OVER SCAN, V POSITION, H POSITION,

H PHASE, H SIZE, AUTO ADJUST EXECUTE

INPUT menu . . . . . . . . . . . . . 31

PROGRESSIVE, VIDEO NR, COLOR SPACE,

COMPONENT, VIDEO FORMAT,

FRAME LOCK, COMPUTER IN,

RESOLUTION

SETUP menu . . . . . . . . . . . . . 34

AUTO KEYSTONE EXECUTE, KEYSTONE ,

WHISPER, MIRROR, VOLUME,

SPEAKER

, AUDIO

SCREEN menu . . . . . . . . . . . . 36

LANGUAGE, MENU POSITION, BLANK,

START UP, M

yScreen

, M

yScreen Lock

,

MESSAGE, SOURCE NAME

OPTION menu . . . . . . . . . . . . 40

AUTO SEARCH, AUTO KEYSTONE

,

AUTO ON, AUTO OFF, LAMP TIME,

FILTER TIME, MY BUTTON, SERVICE,

SECURITY

Maintenance . . . . . . . . . . . . . 51

Lamp . . . . . . . . . . . . . . . . . . . . . . . .51

Air ﬁ lter . . . . . . . . . . . . . . . . . . . . . .53

Other care . . . . . . . . . . . . . . . . . . . .54

Troubleshooting . . . . . . . . . . 55

Related messages . . . . . . . . . . . . . .55

Regarding the indicator lamps . . . . .56

Shutting the projector down . . . . . . .57

Resetting all settings . . . . . . . . . . . .57

Phenomena that may be easy

to be mistaken for machine defects

. .58

Speciﬁ cations . . . . . . . . . . . . 60



ViewSonic

3

PJ758/PJ759/PJ760

Fastening the lens cover

To avoid losing the lens cover, please fasten the

lens cover to the projector using the enclosed strap.

1.

Fix the strap to the strap hole of the lens cover.

Thread one end of the strap through the strap hole

of the lens cover and make the loop at the end, and

let the other end of the strap through the loop. Not

have a knot in the strap at either end.

2.

Fix the strap to the strap hole of the projector.

Thread the other end of the strap through the strap hole of the projector and make

the loop there. Let the lens cover with the one end of strap though the loop.

Projector features / Preparations

Projector features

This projector has a capability to project various picture signals onto a screen.

This projector requires only a minimal amount of space for installation and can

produce a large projected image from even a short distance.

This projector boasts a variety of I/O port and low noise. These features provide

you with the broad use of this projector.

Preparations

Contents of package

Please see the “Contents of package” in the “User’s Manual (concise)” which

is a book. Your projector should come with the items shown there. Contact

immediately your dealer if anything is missing.

NOTE • Keep the original packing materials, for future reshipment. Be sure

to use the original packing materials when moving the projector. Use special

caution for the lens.

ViewSonic

4

PJ758/PJ759/PJ760

Part names

Projector

(1) Lamp cover (



51)

The lamp unit is inside.

(2) Focus ring (



18)

(3) Zoom ring (



18)

(4) Control panel (



5)

(5) Elevator buttons (x 2) (



18)

(6) Elevator feet (x 2) (



18)

(7) Remote sensor (



13)

(8) Lens (



18, 54)

(9) Lens cover (



3)

(10) Intake vents

(11) Filter cover (



53)

The air ﬁ lter and intake vent are

inside.

(12) Speaker (



35)

(13) Exhaust vent

(14) AC inlet (



12)

(15) Power switch (



15)

(16) Rear panel (



5)

(17) Security bar (



12)

(18) Security slot (



12)

WARNING ►HOT! : Do not touch around the lamp cover and the exhaust

vents during use or just after use, since it is too hot.

►Do not look into the lens or vents while the lamp is on, since the strong light

is not good for your eyes.

►Do not handle the elevator buttons without holding the projector, since the

projector may drop down.

CAUTION ►

Maintain normal ventilation to prevent the projector from heating

up. Do not cover, block or plug up the vents. Do not place anything that can stick or

be sucked to the vents, around the intake vents. Clean the air ﬁ lter periodically.

HOT!

(1) (2) (3) (4)

(7)

(10)

(9)

(8)

(11)

(6)

(5)

HOT!

(13)

(12)

(6)

(18)

(16)

(17)

(15)

(14)

(4)

(13)

(1)

(10)

(11)

ViewSonic

5

PJ758/PJ759/PJ760

Part names

Control panel

(1) STANDBY/ON button (



15)

(2) INPUT button (



16, 22)

(3) MENU button (



22)

It consists of four cursor buttons.

(4) POWER indicator (



15, 56)

(5) TEMP indicator (



56)

(6) LAMP indicator (



56)

Rear panel

(1) AUDIO IN1 port (



10)

(2) AUDIO IN2 port (



10)

(3) AUDIO OUT port (



10)

(4) COMPUTER IN1 port (



10)

(5) COMPUTER IN2 port (



10)

(6) MONITOR OUT port (



10)

(7) Shutdown switch (



57)

(8) CONTROL port (



10)

(9) USB port (



10)

(10) COMPONENT

(Y, Cb/Pb, Cr/Pr) port (



10)

(11) VIDEO port (



10)

(12) S-VIDEO port (



10)

(13) AUDIO IN3 (L,R) ports (



10)

CAUTION ►Do not use the security bar and slot to prevent the projector

from falling down, since it is not designed for it.

►Use the shutdown switch only when the projector is not turned off by normal

procedure, since pushing this switch stops operation of the projector without

cooling it down.

(1)

(2)

(3) (4) (7)

(10)

(9)(8) (11)

(6)(5)

(12)(13)

(1) (2)(3)

(4)

(6)

(5)

ViewSonic

6

PJ758/PJ759/PJ760

Part names

Remote control

(1) VIDEO button (



17)

(2) COMPUTER button (



16)

(3) SEARCH button (



17)

(4) STANDBY/ON button (



15)

(5) ASPECT button (



17)

(6) AUTO button (



19)

(7) BLANK button (



21)

(8) MAGNIFY - ON button (



20)

(9) MAGNIFY - OFF button (



14, 20)

(10) HOME button (



14)

(11) END button (



14)

(12) PAGE UP button (



14)

(13) PAGE DOWN button (



14)

(14) VOLUME button (



16)

(15) MUTE button (



14, 16)

(16) FREEZE button (



21)

(17) MY BUTTON - 1 button (



42)

(18) MY BUTTON - 2 button (



42)

(19) KEYSTONE button (



20)

(20) POSITION button (



19, 22)

(21) MENU button (



22)

(22) ▲/▼/◄/► cursor buttons (



14, 22, 23)

(23) ENTER button (



14, 22, 23)

(24) ESC button (



14, 22)

(25) RESET button (



14, 22, 23)

(26) Battery cover (



13)

Back of

the remote control

(2)

(1)

(5)

(10)

(8)

(9)

(11)

(16)

(17)

(20)

(22)

(24)

(3)

(4)

(6)

(7)

(12)

(14)

(15)

(13)

(19)

(18)

(21)

(23)

(25)

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARCH

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

12

ESC

ENTER

MENU

RESET

COMPUTER

(26)

ViewSonic

7

PJ758/PJ759/PJ760

Setting up

Install the projector according to the environment and manner the projector will be

used in.

On a horizontal surface

Suspended from the ceiling

• Keep a space of 30 cm or more

between the sides of the projector

and other objects such as walls.

• Consult with your dealer before

a special installation such as

suspending from a ceiling.

Screen size

(diagonal)

4 : 3 screen 16 : 9 screen

Projection distance

Screen

height

Screen

height

Projection distance

Screen

height

Screen

height

min. max. min. max.

inch m m inch m inch cm inch cm inch m inch m inch cm inch cm inch

30 0.8 0.9 34 1.1 41 41 16 5 2 1.0 38 1.1 45 39 15 -1 0

40 1.0 1.2 46 1.4 56 55 22 6 2 1.3 50 1.5 61 51 20 -2 -1

50 1.3 1.5 58 1.8 70 69 27 8 3 1.6 63 1.9 76 64 25 -2 -1

60 1.5 1.8 70 2.1 84 82 32 9 4 1.9 76 2.3 91 77 30 -2 -1

70 1.8 2.1 81 2.5 98 96 38 11 4 2.3 89 2.7 107 90 35 -3 -1

80 2.0 2.4 93 2.8 112 110 43 12 5 2.6 102 3.1 122 103 41 -3 -1

90 2.3 2.7 105 3.2 126 123 49 14 5 2.9 115 3.5 138 116 46 -4 -1

100 2.5 3.0 117 3.6 140 137 54 15 6 3.2 127 3.9 153 129 51 -4 -2

120 3.0 3.6 140 4.3 169 165 65 18 7 3.9 153 4.7 184 154 61 -5 -2

150 3.8 4.5 176 5.4 211 206 81 23 9 4.9 192 5.8 230 193 76 -6 -2

200 5.1 6.0 235 7.2 282 274 108 30 12 6.5 256 7.8 307 257 101 -8 -3

250 6.4 7.5 294 9.0 353 343 135 38 15 8.1 320 9.8 384 322 127 -10 -4

300 7.6 9.0 352 10.8 423 411 162 46 18 9.8 384 11.7 461 386 152 -12 -5

b

a

b

c1

c1 c2

c2

Arrangement

Refer to the illustrations and tables below to determine screen size and projection distance.

The values shown in the table are calculated for a full size screen: 1024×768.

(a) Screen size (diagonal)

(b) Projection distance (±10%)

(c1), (c2) Screen height (±10%)

ViewSonic

8

PJ758/PJ759/PJ760

Setting up

On a horizontal surface

Suspended from the ceiling

• Keep a space of 30 cm or more

between the sides of the projector

and other objects such as walls.

• Consult with your dealer before

a special installation such as

suspending from a ceiling.

<PJ759>

The values shown in the table are calculated for a full size screen: 1024×768.

(a) Screen size (diagonal)

(b) Projection distance (±10%)

(c1), (c2) Screen height (±10%)

Screen size

(diagonal)

4 : 3 screen 16 : 9 screen

Projection distance

Screen

height

Screen

height

Projection distance

Screen

height

Screen

height

min. max. min. max.

inch m m inch m inch cm inch cm inch m inch m inch cm inch cm inch

30 0.8 0.9 35 1.1 43 41 16 5 2 1.0 39 1.2 47 39 15 -1 0

40 1.0 1.2 47 1.4 57 55 22 6 2 1.3 52 1.6 62 51 20 -2 -1

50 1.3 1.5 59 1.8 71 69 27 8 3 1.6 65 2.0 78 64 25 -2 -1

60 1.5 1.8 71 2.2 86 82 32 9 4 2.0 78 2.4 94 77 30 -2 -1

70 1.8 2.1 83 2.5 100 96 38 11 4 2.3 91 2.8 109 90 35 -3 -1

80 2.0 2.4 95 2.9 115 110 43 12 5 2.6 104 3.2 125 103 41 -3 -1

90 2.3 2.7 107 3.3 129 123 49 14 5 3.0 117 3.6 141 116 46 -4 -1

100 2.5 3.0 119 3.6 144 137 54 15 6 3.3 130 4.0 156 129 51 -4 -2

120 3.0 3.6 143 4.4 172 165 65 18 7 4.0 156 4.8 188 154 61 -5 -2

150 3.8 4.6 179 5.5 216 206 81 23 9 4.9 195 6.0 235 193 76 -6 -2

200 5.1 6.1 239 7.3 288 274 108 30 12 6.6 261 8.0 314 257 101 -8 -3

250 6.4 7.6 299 9.1 360 343 135 38 15 8.3 326 10.0 392 322 127 -10 -4

300 7.6 9.1 359 11.0 432 411 162 46 18 9.9 391 12.0 471 386 152 -12 -5

b

a

b

c1

c1 c2

c2

Arrangement (continued)

ViewSonic

9

PJ758/PJ759/PJ760

Setting up

WARNING ►Place the projector in a stable horizontal position. If the

projector falls or is knocked over it could cause injury and/or damage to the

projector. Using a damaged projector could then result in ﬁ re and/or electric

shock.

• Do not place the projector on an unstable, slanted or vibrational surface such

as a wobbly or inclined stand.

• Do not place the projector on its side, front or rear position.

• Consult with your dealer before a special installation such as suspending

from a ceiling.

►Place the projector in a cool place, and ensure that there is sufﬁ cient

ventilation. The high temperature of the projector could cause ﬁ re, burns and/

or malfunction of the projector.

• Do not stop-up, block or otherwise cover the projector's vents.

• Keep a space of 30 cm or more between the sides of the projector and other

objects such as walls.

• Do not place the projector on metallic thing or anything weak in heat.

• Do not place the projector on carpet, cushions or bedding.

• Do not place the projector in direct sunlight or near hot objects such as

heaters.

• Do not anything near the projector lens or vents, or on top of the projector.

• Do not place anything that may be sucked into or stick to the vents on the

bottom of the projector. This projector has some intake vents also on the

bottom.

►Do not place the projector anyplace where it may get wet. Getting the

projector wet or inserting liquid into the projector could cause ﬁ re, electric

shock and/or malfunction of the projector.

• Do not place the projector in a bathroom or the outdoors.

• Do not place anything containing liquid near the projector.

CAUTION ►Avoid placing the projector in smoky, humid or dusty place.

Placing the projector in such places could cause ﬁ re, electric shock and/or

malfunction of the projector.

• Do not place the projector near humidiﬁ ers, smoking spaces or a kitchen.

►Position the projector to prevent light from directly hitting the projector's

remote sensor.

ViewSonic

10

PJ758/PJ759/PJ760

Setting up

Connecting your devices

Be sure to read the manuals for devices before connecting them to the projector.

Make sure that all the devices are suitable to be connected with this product, and

prepare the cables required to connect.

Please refer to the following illustrations to connect them.

WARNING ►Do not disassemble or modify the projector and accessories.

►Be careful not to damage the cables, and do not use damaged cables.

CAUTION ►Turn off all devices and unplug their power cords prior to

connecting them to projector. Connecting a live device to the projector may

generate extremely loud noises or other abnormalities that may result in

malfunction or damage to the device and the projector.

►Use appropriate accessory or otherwise designed cables. Ask your dealer

about non-accessory cables which may have to be of a speciﬁ c length or

equipped with a core. For cables with a core only at one end, connect the end

with the core to the projector.

►Make sure that devices are connected to the correct ports. An incorrect

connection may result in malfunction or damage to the device and the projector.

AUDIO IN

Y CB/PB CR/PR

COMPONENT VIDEO OUT

L R

AUDO IN OUT

VIDEO OUT

L R

AUDO IN OUT

L R

AUDO IN OUT

S-VIDEO OUT

AUDIO OUT

RGB OUT

AUDIO OUT

USB

RGB OUT

RS-232C

RGB IN

VCR/DVD

player

Speakers

PC

Monitor

ViewSonic

11

PJ758/PJ759/PJ760

Setting up

NOTE • Be sure to read the manuals for devices before connecting them to the

projector, and make sure that all the devices are suitable to be connected with this

product. Before connecting to a PC, check the signal level, the signal timing, and the

resolution.

- Some signal may need an adapter to input this projector.

- Some PCs have multiple screen display modes that may include some signals which

are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA (1600X1200),

the signal will be converted to the projector’s panel resolution before being displayed.

The best display performance will be achieved if the resolutions of the input signal and

the projector panel are identical.

• While connecting, make sure that the shape of the cable's connector ﬁ ts the port to

connect with. And be sure to tighten the screws on connectors with screws.

• When connecting a laptop PC to the projector, be sure to activate the PC’s external

RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT

display.) For details on how this is done, please refer to the instruction manual of the

corresponding laptop PC.

• When the picture resolution is changed on a pc depending on an input, automatic

adjustment function may take some time and may not be completed. In this case,

you may not be able to see a check box to select “Yes/No” for the new resolution on

Windows. Then the resolution will go back to the original. It might be recommended to

use other CRT or LCD monitors to change the resolution.

• In some cases, this projector may not display a proper picture or display any picture on

screen. For example, automatic adjustment may not function correctly with some input

signals. An input signal of composite sync or sync on G may confuse this projector, so

the projector may not display a proper picture.

About Plug-and-Play capability

Plug-and-Play is a system composed of a PC, its operating system and peripheral

equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-

Play can be used by connecting this projector to a pc that is VESA DDC (display data

channel) compatible.

• Take advantage of this feature by connecting an RGB cable to the COMPUTER IN1

port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of

connection is attempted.

• Please use the standard drivers in your pc as this projector is a Plug-and-Play monitor.

Connecting your devices (continued)

ViewSonic

12

PJ758/PJ759/PJ760

Setting up

Connecting power supply

At ﬁ rst, make sure that the power switch of the

projector is set to OFF position (marked "O").

1.

Put the connector of the power cord into

the AC inlet of the projector.

2.

Firmly plug the power cord’s plug into the

outlet.

WARNING ►Please use extra caution when connecting the power cord, as

incorrect or faulty connections may result in ﬁ re and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, contact

your dealer to newly get correct one.

• Only plug the power cord into an outlet rated for use with the power cord's

speciﬁ ed voltage range. The power outlet should be close to the projector and

easily accessible. Remove the power cord for complete separation.

• Never modify the power cord.

Using the security bar and slot

A commercial anti-theft chain or wire up to

10 mm in diameter can be attached to the

security bar on the projector.

Also this product has the security slot for the

Kensington lock.

For details, see the manual of the security

tool.

WARNING ►Do not use the security bar and slot to prevent the projector

from falling down, since it is not designed for it.

CAUTION ►Do not place anti-theft chain or wire near the exhaust vents. It

may become too hot.

NOTE • The security bar and slot is not comprehensive theft prevention

measures. It is intended to be used as supplemental theft prevention measure.

AC inlet

Power cord

ViewSonic

13

PJ758/PJ759/PJ760

Remote control

Putting batteries

Please set the batteries to the remote control before using it. If the remote control starts

to malfunction, try to replace the batteries. If you will not use the remote control for long

period, remove the batteries from the remote control and store them in a safe place.

1.

Holding the hook part of the battery

cover, remove it.

2.

Align and insert the two AA batteries

according to their plus and minus terminals

as indicated in the remote control.

3.

Replace the battery cover in the direction of the arrow and snap it back into place.

Remote control

WARNING ►Always handle the batteries with care and use them only as

directed. Improper use may result in battery explosion, cracking or leakage,

which could result in ﬁ re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries speciﬁ ed. Do not use batteries of different

types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not allow a battery in a ﬁ re or water. Keep batteries in a dark, cool and dry place.

•

If you observe battery leakage, wipe out the leakage and then replace a battery. If the

leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

About the remote control signal

The remote control works with the projector’s

remote sensor. This projector has a remote sensor

on the front.

The sensor senses the signal within the following

range when the sensor is active:

60 degrees (30 degrees to the left and right of the

sensor) within 3 meters about.

NOTE • The remote control signal reﬂ ected in the screen or the like may

be available. If it is difﬁ cult to send the signal to the sensor directly, attempt to

make the signal reﬂ ect.

• The remote control uses infrared light to send signals to the projector (Class 1 LED),

so be sure to use the remote control in an area free from obstacles that could block

the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun light) or light

from an extremely close range (such as from an inverter ﬂ uorescent lamp) shines on the

remote sensor of the projector. Adjust the position of projector avoiding those lights.

30º

Approx.

3 m

ViewSonic

14

PJ758/PJ759/PJ760

Using as a simple PC mouse & keyboard

The enclosed remote control works as a simple mouse and

keyboard of the PC, when the projector's USB port (B type)

connects with the PC's USB port (A type) port via a mouse cable.

(1) HOME key: Press HOME button.

(2) END key: Press END button.

(3) PAGE UP key: Press PAGE UP button.

(4) PAGE DOWN key: Press PAGE DOWN button.

(5) Mouse left button: Press ENTER button.

(6) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►.

(7) ESC key: Press ESC button.

(8) Mouse right button: Press RESET button.

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal

frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote

control does not function properly, attempt to change the signal

frequency.

In order to set the Mode, please keep pressing the combination of

two buttons listed below simultaneously for about 3 seconds.

(1) Set to Mode 1:NORMAL... MUTE and RESET buttons

(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons

Please remember that the REMOTE FREQ. in the SERVICE

item of the OPTION menu (



44) of the projector to be controlled

should be set to the same mode as the remote control.

Remote control

NOTE •

When the simple mouse & keyboard function of this product does not work

correctly, please check the following.

- When the mouse cable connects this projector with a PC having a built-in pointing

device (e.g. track ball) like a notebook PC, open BIOS setup menu, then select the

external mouse and disable the built-in pointing device, because the built-in pointing

device may have priority to this function.

- Windows 95 OSR 2.1 or higher is required for this function. And also this function may

not work depending on the PC’s conﬁ gurations and mouse drivers.

- You cannot do things like press two buttons at once (for instance, pressing two buttons

at the same time to move the mouse pointer diagonally).

- This function is activated only when the projector is working properly. This function is

not available while the lamp is warming up (the POWER indicator blinks green), and

while adjusting the volume and display, correcting for keystone, zooming in on the

screen, using the BLANK function, or displaying the menu screen.

CAUTION ►Improper use of the simple mouse

& keyboard function could damage your equipment.

While using this function, please connect this product

only to a PC. Be sure to check your PC’s manuals

before connecting this product to the PC.

(1)(2)

(3)(1)

(2)

(5)

(7)

(4)

(6)

(8)

USB port

USB

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARCH

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

12

ESC

ENTER

MENU

RESET

COMPUTER

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARCH

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

12

ESC

ENTER

MENU

RESET

COMPUTER

ViewSonic

15

PJ758/PJ759/PJ760

Turning on the power

1.

Make sure that the power cord is ﬁ rmly and correctly

connected to the projector and the outlet.

2.

Remove the lens cover, and set the power switch to

ON position (marked “ I “).

The POWER indicator will light up in steady orange

(



56). Then wait several seconds because the

buttons may not function for these several seconds.

3.

Press STANDBY/ON button on the projector or the

remote control.

The projection lamp will light up and POWER indicator

will begin blinking in green. When the power is

completely on, the indicator will stop blinking and light

in steady green (



56).

To display the picture, select an input signal according to the section “Selecting an input

signal” (



16).

Power on/off

WARNING

►A strong light is emitted when the projector’s power is on. Do

not look into the lens of the projector or look inside of the projector through any

of the projector’s openings.

►Do not touch around the lamp cover and the exhaust vents during use or just

after use, since it is too hot.

NOTE • Turn the power on/off in right order. Please power on the projector prior

to the connected devices. Power off the projector after all of connected devices are

powered off.

•

The projector has the AUTO ON function, which can make the projector automatically

turn on. For more information, please see AUTO ON item of OPTION menu

(



40).

• Use the shutdown switch (



57) only when the projector is not turned off by

normal procedure.

Power on/off

Turning off the power

1.

Press the STANDBY/ON button on the projector or the remote control. The message

“Power off?” will appear on the screen for about 5 seconds.

2.

Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange.

Then POWER indicator will stop blinking and light in steady orange when the lamp

cooling is complete(



56).

3.

Make sure that POWER indicator lights in steady orange, and set the

power switch to OFF position (marked “O“).

POWER indicator will go off. Attach the lens cover.

Do not turn the projector on for about 10 minutes or more after turning it off. Turning the projector

on again too soon could shorten the lifetime of some consumable parts of the projector.

HOME

PAGE UP

PAGE DOWN

END

VIDEO

SEARCH

FREEZE

OFF

ON

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

MY BUTTON

POSITION

12

ESC

ENTER

MENU

RESET

COMPUTER

Page is loading ...

ViewSonic PJ758/PJ759/PJ760, PJ759, PJ760, VS11861 User manual

Related papers

Other documents