Bernina 330 Owner's manual

Brand: Bernina

Model: 330

Category: Sewing machines

Type: Owner's manual

This manual is also suitable for

BERNINA 330

350 PE

380

Dear Bernina Customer,

Congratulations!

You’ve decided on BERNINA, a reliable choice that will delight you for years to come.

For over 100 years, our family has placed the highest value on satisfied customers. For

myself, it is a matter of personal pride to offer you Swiss precision at the height of

perfection, future-oriented sewing technology, and a comprehensive customer service.

The BERNINA 330, 350 and 380 are primarily aimed at the occasional sewer who puts

great stock in design and customer benefit. These sewing computers are very ergonomi-

cally built and therefore even easier to operate, to help you, our esteemed customers,

on your journey to even greater sewing pleasure and perfect results.

Enjoy creative sewing with BERNINA:

Find out about our varied range of accessory and let yourself be inspired by new sewing

projects at www.bernina.com.

And don’t forget to make use of service and maintenance offers from our highly trained

BERNINA dealers.

H.P. Ueltschi

Owner

BERNINA International AG

CH-8266 Steckborn

www.bernina.com

Introduction

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Safety Instructions

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliance, basic safety

precautions should always be followed, including

the following:

Read all instructions before using this sewing

computer.

When the sewing computer is not in use, it

should be disconnected from the electricity

supply by removing the plug from the outlet.

DANGER!

To reduce the risk of electrical shock:

1. The sewing computer should never be left

unattended when plugged in.

2. Always unplug the sewing computer from the

electrical outlet immediately after using and

before cleaning.

3. LED radiation. Do not view directly with

optical instruments. LED class 1M

WARNING!

To reduce the risk of burns, fire, electric shock or

injury to persons:

1. Use the sewing computer only for purposes

as described in this manual. Use only

attachments/accessory recommended by the

manufacturer as contained in this manual.

2. Do not allow the sewing computer to be

used as a toy. Close attention is necessary

when this sewing computer is used by or

near children and infirm persons. This

sewing computer is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the sewing

computer by a person responsible for their

safety. Children must be kept under

supervision to ensure that they do not play

with the sewing computer.

3. Never operate this sewing computer if:

█

it has a damaged cord or plug

█

it is not working properly

█

it has been dropped or damaged

█

it has fallen into water

Take the sewing computer to the nearest

authorized BERNINA dealer for examination,

repair, electrical or mechanical adjustment.

4. Never operate the sewing computer with any

air vents blocked. Keep ventilation openings

of the sewing computer free from lint, dust

and/or fabric bits.

5. Keep fingers away from all moving parts.

Special care is required in the needle area of

the sewing computer.

6. Never drop or insert any objects into any

opening on the sewing computer.

7. Do not use the sewing computer outdoors.

8. Do not operate the sewing computer where

aerosol products (spray) or oxygen is being

administered.

9. Do not pull or push the fabric while stitching.

This may deflect the needle, causing it to

break.

10. Do not use bent needles.

11. Always use the BERNINA original stitch

plate. The wrong stitch plate can cause

needle breakage.

12. To disconnect, turn power switch to «0» (off),

then remove the plug from the outlet. Do not

unplug by pulling the cord, instead grasp the

plug to pull it from the outlet.

13. Turn power switch to «0» (off) when making

any adjustments in the needle area, such as

changing the needle or the presser foot, etc.

14. Always unplug the sewing computer from the

electrical outlet when carrying out cleaning

or maintenance work or any other user

servicing adjustments mentioned in this

manual.

15. This sewing computer is provided with

double insulation (except USA and Canada).

Use only genuine replacement parts. Please

note the advice on the servicing of double-

insulated products.

SAFETY INSTRUCTIONS

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Safety Instructions

Please find the latest version of

your instruction manual at

www.bernina.com

SERVICING DOUBLE

INSULATED PRODUCTS

In a double-insulated product, two systems of

insulation are provided instead of grounding. No

grounding means is provided on a double-

insulated product nor should a means for

grounded be added to the product. Servicing a

double-insulated product requires extreme care

and knowledge of the system and should only be

done by qualified service personnel. Replacement

parts for a double-insulated product must be

identical to the original parts in the product.

A double insulated product is marked with the

words: «Double-Insulation» or «double-insulated».

The symbol

may also be marked on the

product.

DISCLAIMER

No liability will be assumed for any possible

damage which

arises from misuse of this sewing computer.

This sewing computer is intended for household

use only.

SAVE THESE

INSTRUCTIONS!

Environmental Protection

BERNINA is committed to the protection

of the environment. We strive to

minimize the environmental impact of our

products by continuously improving

product design and our technology of

manufacturing.

At end of life please dispose this product

in an environmentally responsible way

according to the national directive. Do

not throw away this product with your

household waste. In case of doubt,

please contact your dealer.

If the sewing computer is stored in a cold

room, it should be brought to a warm

room about one hour before use.

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

* Not supplied as standard with the BERNINA 330

** Not supplied as standard with the BERNINA 350

*** Not supplied as standard with the BERNINA 380

Very important!

Risk of damage!

Supplementary information!

Glossary

Balance Correcting abnormalities in stitch formation due to the fabric

clr Deleting settings or data

LED Sewing light system

FHS Free-Hand System = Knee-operated presser-foot lifter

mem Memory = Longterm data store

Bartack Buttonhole-bead cross-connections

Satin stitching Dense zig-zag

Fabric fold Folded edge of material

Hook «Catches» the needle-thread loop, forming

the seam together with the lower thread

Contents - Key to Signs

Accessory

5-7

8-23

24-29

30-43

47-49

Preparation

█

Details of the sewing computer 8

█

Preparation for sewing 10

Functions

█

Function buttons on the sewing

computer 24

█

Details of the screen 26

Sewing stitches

█

Practical stitches 30

█

Examples of application 31

Cleaning, maintenance

█

Sewing computer and screen 44

█

Lubricating 44

Troubleshooting

Stitch patterns

Index

█

Buttonholes 36

█

Practical-/Quiltstitch 43

█

Memory 27

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Accessory

Standard Accessory

█

Fabric cover

█

Accessory box */**

█

Accessory case ***

█

Foot control

█

Power cable

█

Slide-on table*

█

Stitch pattern summary card

█

Free-Hand System FHS */**

1 5 bobbins (one of them in the bobbin case)

2 Selection of needles

3 Seam guide, right

4 Height compensating tool

5 Seam ripper

6 Screwdriver, red

7 Angular Torx button

8 Lint brush

9 Lubricator

10 2 foam pads

11 3 spool discs

3 4 6

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Presser Feet/Snap-On Soles (BERNINA 330/350/350 PE/380)

Presser Feet - Standard (BERNINA 350/350 PE/380)

1 No. 1 Reverse pattern sole

2 No. 2 Overlock sole (without 350 PE)

3 No. 3A Automatic Buttonhole foot with

slide

4 No. 4 Zipper sole

5 No. 5 Blindstitch sole

6 No. 8 Jeans sole */**/(without

350 PE)

7 No. 20 Open embroidery sole *

8 No. 37 Patchwork sole (only 350 PE)

Accessory

7 8

1 No. 1 Reverse pattern foot

2 No. 2 Overlock foot (without 350 PE)

3 No. 3A Automatic Buttonhole foot with

slide

4 No. 4 Zipper foot

5 No. 5 Blindstitch foot

6 No. 8 Jeans foot **/(without 350 PE)

7 No. 20 Open embroidery foot

8 No. 37 Patchwork foot (only 350 PE)

More accessories you can

found on www.bernina.com

Presser Feet: can vary from country to country (Snap-On Soles or Standard).

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Accessory

Accessory Box */**

Accessory Case ***

Storing Accessory

Standard accessory are supplied in a plastic bag. They can be stored as

shown in the picture.

Standard accessory for the models B330/350 can be carefully stored in the

case. Buttonhole foot 3A is stored inside in a separate compartment.

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Preparation - Details of the sewing computer

Front View

Detail View

13 14

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Preparation - Details of the sewing computer

1 Bobbin cover

2 Stitch plate

3 Attachment base for

special accessory

4 LED sewing light

5 Quick reverse button

6 Start/Stop button

7 Thread take-up cover

8 Thread take-up lever

9 Bobbin winder pre-tension

10 Speed control

11 Screen

12 Needle stop up/down

button

13 Pattern end button

14 Mirror image button */**

15 Stitch length buttons

16 Needle position buttons

17 Stitch width buttons

18 Bobbin winder device

19 Thread cutter on bobbin

winder

20 Memory buttons

21 Alphabet button

22 Stitch selection buttons

23 #-button (hash button)

24 «clr» (clear) button

25 Slide-on table socket

26 FHS (Free Hand System)

connection *

27 Thread tension adjustment

wheel

28 Rear thread guide

29 Carrying handle

30 Vertical spool pin

31 Horizontal spool pin

32 Eyelet

33 Handwheel

34 Balance adjuster

35 Foot control socket

36 Feed-dog drop

37 Power switch on/off

38 Power plug socket

39 Needle threader

40 Thread guide

41 Needle clamp

42 Presser Foot

43 Thread cutter in hook

opening

44 Feed dog

45 Thread cutter on head

frame (left)

46 Presser foot lifter

47 Darning hoop connection

(USA/Canada only):

The sewing computer has a polarized plug (one

blade wider than the other). To reduce the risk of

electrical shock, this plug is intended to fit in a

polarized outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to install the

proper outlet. Do not modify the plug in any way!

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

The LED sewing light illuminates the sewing area and has a long product life.

LED Sewing Light

Please note that a defective sewing light must ONLY be re-

placed by an authorized technician.

The sewing computer must be taken to an authorized BERNINA

dealer!

Sewing speed control

█

control the sewing speed by pressing the foot control

Self storing cord

█

wind the cable around the spool

█

insert the plug into the groove provided

While sewing

█

unwind the cable

Foot Control

Slide-on Table *

The slide-on table increases the sewing surface.

Attaching the slide-on table

█

raise needle and presser foot

█

slide over free-arm to the right until it engages

Removing the slide-on table

█

raise needle and presser foot

█

press button down and pull off slide-on table to the left

Preparation - Sewing

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Preparation - Sewing

The FHS raises and lowers the presser foot.

Attaching the lifter

█

insert into the opening; you should be able to operate the FHS with your

knee in your normal sitting position

Raising and lowering the presser foot

█

with your knee push lever to the right

█

the presser foot is raised; the feed dog is lowered simultaneously. The

thread tension is released

█

the feed dog is raised as soon as the first stitch is sewn

Presser Foot Lifter (FHS) */**

█

the vertical spool pin is on the side behind the handwheel

█

it is an essential aid for sewing with more than one thread, i.e. double need-

le work

█

raise the pin until it clicks into its vertical position

█

when using large reels, add the foam pad A for stability

Vertical Spool Pin

Your dealer can adjust the FHS if necessary.

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Inserting a Bobbin

Insert the bobbin so that the thread runs clockwise.

Laying the thread into the slot

Pull the thread counter clockwise into the slot.

Pulling the thread under the spring

Pull the thread to the left under the spring until it lies in the T-shaped slit at the

end of the spring. The bobbin must turn clockwise.

Preparation - Sewing

█

turn power switch on (to «I»)

█

place empty bobbin on spindle

█

place thread on spool pin

█

attach appropriate spool disc; diameter of thread spool determines disc size

█

following the direction of the arrow take thread through the rear guide and

round the pre-tension stud

█

wind the thread two to three times around the empty bobbin and cut off any

excess thread on the thread cutter

█

push engaging lever against bobbin, the winder works automatically

█

the motor will stop automatically when the bobbin is full

Winding a Bobbin

Bobbin winding while sewing

█

place thread spool on vertical spool pin then, following the direction of the

arrow, take thread through the thread guide and around the pre-tension

stud

█

then proceed as mentioned above

Thread cutter

█

pull thread over thread cutter when removing the bobbin

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Preparation - Sewing

Bobbin Case

To remove the bobbin case

█

raise needle

█

power switch to «0» (off)

█

open the bobbin cover

█

grasp the latch of the bobbin case

█

remove bobbin case

Bobbin thread cutter

█

insert the bobbin case

█

take the thread over cutter A and cut it

█

close the bobbin cover

To insert the bobbin case

█

hold the bobbin case latch

█

the finger on the case should point upwards

█

insert the case so that it clicks into place

The bobbin thread does not have to be brought up as the loose end

is just the right length to start sewing.

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Preparation - Sewing

Threading the Upper Thread

Attaching the thread spool

█

raise the needle and presser foot

█

power switch to «0» (off)

█

place foam pad on pin base

█

place spool on pin (thread unwinds clockwise)

█

attach appropriate spool disc - diameter of spool determines disc size, there

must be no clearance between the disc and the spool

█

take thread through rear guide A

█

then into slit of upper thread tension B

█

pull thread down to the right of the take-up cover and around C

█

take thread up to the left of the cover and around D, placing it in the

take-up lever

█

take thread down and through guides E and F

Needle Threader

1 Press lever down

█

raise needle

█

lower the presser foot

█

hold thread to the left and back

█

press lever A down and simultaneously guide the thread around hook B to

the right to the needle

2 Guide thread to front of the needle

█

put the thread from the front into the guide C until it catches in the wire

hook

3 Release lever and thread

█

release lever A and thread

█

put the thread under the foot and pull the thread backwards or

█

put the thread under the foot and pull it from front to back over the thread

cutter on left side of the head frame

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Preparation - Sewing

Threading the First Thread

█

place thread spool on horizontal spool pin and thread

█

guide the thread to the front in the slit and past the tension disc A on the

right side

█

thread sewing computer as usual and thread the right needle

Threading the Second Thread

█

place thread spool on the vertical spool pin and thread

█

guide the thread to the front in the slit and past the tension disc A on the

left side

█

thread the left needle

█

threads must not be twisted together

█

two thread spools and one full bobbin are needed

█

place one thread spool on horizontal spool pin

█

place second thread spool and the bobbin, separated by a spool disc, on

vertical spool pin (both spools have to turn in the same direction)

█

thread as usual by guiding two threads on the left side of the tension disc A

and one thread on the right side of the disc

Threading the Double Needle

Threading the Triple Needle

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Removing the needle

█

raise needle

█

power switch to «0» (off)

█

lower the presser foot

█

loosen the needle clamp screw

█

pull the needle down to remove

Inserting the needle

█

flat side of needle to the back

█

insert the needle as far as it will go

█

tighten the needle clamp screw

Changing the Needle

Thread Cutter

On the left of the head frame

█

pull both threads from front to back over the cutter

█

the threads release automatically as soon as the first stitch is sewn

Preparation - Sewing

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Preparation - Sewing

Changing the Presser-Foot Sole

█

raise the needle and the presser foot shaft

█

power switch to «0» (off)

█

press the button on the shaft to release the sole

Attaching the presser-foot sole

█

place the presser-foot sole under the shaft so that the peg sits under the

opening of the shaft

█

lower the presser-foot lifter and the foot sole will click into position

Changing the Presser Foot

█

raise the needle and presser foot

█

power switch to «0» (off)

Raising the Lever

█

raise the clamping lever

█

remove the presser foot

Attaching the Presser Foot

█

guide the foot upwards over the cone

█

press the clamping lever down

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Preparation - Sewing

Thread Tension

The Basic Setting

█

is indicated when the red line on the tension adjustment wheel is in line with

the marking A

█

the tension does not need adjusting for normal sewing work

█

for special sewing work, the tension can be adjusted to suit the fabric

Perfect Stitch Formation

█

the interlooping of the threads is in the fabric

Upper thread tension too tight

█

the lower thread is pulled more up, i.e. to the right side of the fabric

█

to reduce the upper thread tension turn tension adjustment wheel to 3-1

Upper thread tension too loose

█

the upper thread is pulled more down, i.e. to the wrong side of the fabric

█

to increase the upper thread tension turn tension adjustment wheel to 5-10

Optimal upper thread tension is set in the factory. For this, Metrosene

threads 100/2 weight (Mettler, Switzerland) are used in the bobbin and

also in the upper thread.

The tension may vary when using other types of thread such as embroidery

thread, and it may therefore be necessary to adjust the tension to suit the fabric

and stitch type.

For example:

Tension Needle

Metallic thread approx. 3 90

Monofilament approx. 2-4 80

Stitch Plate

Stitch Plate Markings

█

the stitch plate is marked with vertical, horizontal and diagonal lines in mm

and inches

█

the lines help to guide the fabric for sewing seams and precise topstitching,

etc.

█

the horizontal markings are helpful for sewing corners and buttonholes, etc.

█

the diagonal markings are useful for quilting

█

the vertical measurements correspond to the distance between the needle

and the line

█

needle insertion point is position 0 (center needle position)

█

the measurements are marked to the right and left, measuring from the

center needle position

Removing the Stitch Plate

█

raise the presser foot and needle

█

power switch to «0» (off)

█

press the stitch plate down at the right back corner B until it flips up

█

remove the stitch plate

Replacing the Stitch Plate

█

place the stitch plate over the opening A and press down until it clicks into

place

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Preparation - Sewing

Balance

Different fabrics, threads and stabilizers can naturally affect the stitch balance

so that the stitch patterns are sewn too close together or not close enough.

This can be remedied with Balance to suit the fabric and produce perfect

results.

Normal position

Denser stitch formation - pulling the stitch pattern closer together

(shorter stitch length)

Finer stitch formation - extending the stitch pattern

(longer stitch length)

Test-sewing

When using decorative stitches, we recommend to test-sew the

stitch pattern on a piece of the project fabric.

If the balance has been adjusted, return it to the normal setting once

sewing is completed!

033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN

Page is loading ...

Bernina 330 Owner's manual

Brand: Bernina

Model: 330

Category: Sewing machines

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Bernina 330 Owner's manual

This manual is also suitable for

Bernina 330 Owner's manual

Related papers

Other documents