Chief PDR2644B Installation guide
- Category
- Flat panel wall mounts
- Type
- Installation guide
Chief PDR2644B is a large flat panel interface bracket designed for mounting flat panel displays to a wall. It supports 400mm x 300mm and 300mm x 300mm mounting patterns and can hold up to 175 lbs (79.4 kg) of weight. The bracket is easy to install and comes with all the necessary hardware.
Chief PDR2644B is a large flat panel interface bracket designed for mounting flat panel displays to a wall. It supports 400mm x 300mm and 300mm x 300mm mounting patterns and can hold up to 175 lbs (79.4 kg) of weight. The bracket is easy to install and comes with all the necessary hardware.
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Large Flat Panel Interface Bracket
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PSB-2644
PSB-2644 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the maximum weight
installed on the interface bracket doesn’t exceed 175 lbs
(79.4 kg).
DIMENSIONS
17.11
434.6
20.75
527.1
6.49
164.9
13.20
335.3
11.02
279.9
7.40
188
3.06
77.8
1.45
36.9
.50
12.7
2.55
64.7
6.31
160.4
8.19
208
.58
14.7
3.56
90.5
4.52
114.7
.67
17.1
.35
9
BRACKET WORKS WITH 400MM x 300MM AND
300MM x 300MM MOUNTING PATTERNS
Installation Instructions PSB-2644
3
TOOLS / PARTS FOR INSTALLATION
ASSEMBLY AND INSTALLATION
NOTE: Brackets will work with 400x300mm or 300x300mm
mounting patterns.
1. Attach mounting buttons (C) to interface brackets (A and B)
using four #10-24 x 1/2" button head cap screws (D) and a
1/8" hex key (G). (See Figure 1)
NOTE: Mounting buttons (C) may be installed to lower holes if
more space is needed below display. (See Figure 1)
Figure 1
2. Attach the interface brackets (A and B) to the back of the
display using four M6x20mm Phillips pan machine screws
(E), four spacers (F) and a #2 screwdriver. (See Figure 2)
CAUTION: Using screws of improper length or diameter
may damage your display! Only use screws provided with
interface bracket!
NOTE: Use the inside holes for 300x300mm mounting
patterns. (See Figure 2)
Figure 2
3. Complete the installation following the mount installation
instructions.
1/8"
(Included)
A (1)
[right interface
bracket]
B (1)
[left interface
C (4)
[mounting
button]
G (1)
1/8"
bracket]
D (4)
#10-24 x 1/2
E (4)
M6x20mm
F (4)
.75x.25x.25
1
(D) x 4
(C) x 4
(A)
(B)
lower button
holes
(A)
3
(E) x 4
(400mmx300mm
mounting pattern shown)
300x300mm
mounting pattern
(B)
(F) x 4
PSB-2644 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8804-002017 Rev00
2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
07/10
-
1
-
2
-
3
-
4
Chief PDR2644B Installation guide
- Category
- Flat panel wall mounts
- Type
- Installation guide
Chief PDR2644B is a large flat panel interface bracket designed for mounting flat panel displays to a wall. It supports 400mm x 300mm and 300mm x 300mm mounting patterns and can hold up to 175 lbs (79.4 kg) of weight. The bracket is easy to install and comes with all the necessary hardware.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Chief PSB2020 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Chief Manufacturing PSB-2033 User manual
-
Dell C7017T Quick start guide
-
Infocus PRJ-MNT-INST Specification
-
-
-
-
-
Sanus SAN18B Instructions Manual
-
Atdec AC-AP-4040 Installation guide