Manitowoc Ice K00385 User manual

Manitowoc Ice
Brand
Manitowoc Ice
Model
K00385
Category
Ice cube makers
Type
User manual

Manitowoc Ice K00385 is an adapter kit used for installing S-1474 or S-1870 ice machines on a B-970 bin. The kit includes a stainless steel support/deflector, fillers, foam tape, and screws. The support/deflector is placed on the front edge of the bin and positioned as far forward as possible. The fillers are then placed on the bin and aligned with the holes in the support/deflector. The fillers are attached with screws, and foam tape is applied to the front and back of the bin between the fillers.

Manitowoc Ice K00385 is an adapter kit used for installing S-1474 or S-1870 ice machines on a B-970 bin. The kit includes a stainless steel support/deflector, fillers, foam tape, and screws. The support/deflector is placed on the front edge of the bin and positioned as far forward as possible. The fillers are then placed on the bin and aligned with the holes in the support/deflector. The fillers are attached with screws, and foam tape is applied to the front and back of the bin between the fillers.

K00385 ADAPTER KIT
Installation Instructions
The K00385 kit is used for installing S-1474 or S-1870 ice machines on a B-970 bin.
(Refer to Sheet 2 of 3 for pre-installation instructions.)
1. Note: Bin must be level before installation of ice machine.
A. Remove the foam tape from the front and sides of the bin where the stainless support/deflector will be located.
Use the support to reference the areas where the tape should be removed.
B. Place the support on the front edge of the bin and position as far forward as possible.
C. Locate the four pieces of the 2” long, 3/4” wide foam tape in the front corners, as shown.
D. Place the fillers on the bin, as shown. Make sure the two holes from the stainless support/deflector and fillers are
aligned on the side.
E. Using the fillers as templates, drill three 5/32” (4 mm.) holes, .500” (12.7 mm.) deep maximum, in the bin.
Warning: Do not drill through the interior liner. Attach each filler with three 10-24 x .500” screws provided.
F. Apply foam tape to the front and back of the bin between the fillers. Note: All other required foam tape comes
preassembled with the stainless support/deflector and fillers.
G. Note: It is recommended to RTV intersections and along the inside edge of the foam tape to prevent water
tracking.
2. Refer to ice machine installation manual for ice machine installation procedures.
Manitowoc Ice, Inc.
2110 South 26
th
Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA 000002544
Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Sheet 1 of 3
Web Site - www.manitowocice.com 06/13/07
Filler
Filler
.75” Wide Foam Tape
INSTALLER: It is
recommended to RTV
intersections and along inside
edge of foam tape to prevent
water tracking
Filler
#10-24 x .50”L
Screws Typ
Stainless Steel
Support/Deflector
.75” x 2.00”L Foam Tape
Typ both front corners
.75” Wide Foam Tape
Pre-installation Instructions for Removal of Existing Plastic Deflector
1. Remove the left and right side cover screws (see View A).
2. Remove the cover to expose the four screws that secure the plastic deflector (see Detail B).
3. Take out the four screws. Remove the plastic deflector, replace with a polymer spacer on each side and secure with
the four screws.
4. Reinstall the cover and proceed with the installation instructions.
000002544
Sheet 2 of 3
06/13/07
Plastic Deflector
Cover
Plastic Deflector
Screws
See Detail B
Detail B
View A
Cover Screw
Installing Ice deflector
1. Locate correct position for the deflector.
If the ice machine is installed, remove the water trough to obtain easier access.
The deflector must be located in the center of the drop zone.
Location is 11” from the left edge of the ice machine to the left edge of the mounting bracket.
2. Cut and remove the foam tape on the front and back of the bin where the deflector will be located.
3. Remove any residual adhesive; areas must be clean and dry.
4. Remove protective covering from the two sided tape on each deflector bracket.
5. Install the deflector bracket.
Distribute the mounting bracket equally on the front and back of the bin.
Locate the retaining pin to the back.
Press the mounting bracket into place.
6. Trim supplied foam tape to length of cuts from step 2 and apply over the top of the bracket. Seal edges
where deflector mounting bracket meets foam tape with silicone sealant to prevent water leakage.
7. Install the deflector into the mounting bracket.
Align tabs and slide the deflector toward the front of the bin.
Insert retaining pin into hole in the mounting bracket to lock deflector in place.
Reinstall water trough if removed in step 1.
000002544
Sheet 3 of 3
06/13/07
Water
Pump
Location
Water Trough
Located Behind
Splash Shield
Splash
Shield
Ice Deflector
  • Page 1 1
  • Page 2 2
  • Page 3 3

Manitowoc Ice K00385 User manual

Manitowoc Ice
Brand
Manitowoc Ice
Model
K00385
Category
Ice cube makers
Type
User manual

Manitowoc Ice K00385 is an adapter kit used for installing S-1474 or S-1870 ice machines on a B-970 bin. The kit includes a stainless steel support/deflector, fillers, foam tape, and screws. The support/deflector is placed on the front edge of the bin and positioned as far forward as possible. The fillers are then placed on the bin and aligned with the holes in the support/deflector. The fillers are attached with screws, and foam tape is applied to the front and back of the bin between the fillers.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents