Page is loading ...
SERVICE MANUAL
SERVICE MANUAL
This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not
contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by
electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or
products dealt with in this service information by anyone else could result in serious injury or death
MODEL:
Front Load Washing Machine
WARNING
©2011 Front Load Haier Washing Machine
All rights reserved. Unauthorized copying and distribution is a violation of law.
Front Load Washing Machine
Order No.
L614WD13
03D Series
SERVICE MANUAL
2
Front Load Washing Machine
21
21
21
22
03D Series
SERVICE MANUAL
3
Front Load Washing Machine
03D Series
22
23
23
24
28
9
33
10 Washing process table
Front Load Washing Machine
03D Series
SERVICE MANUAL
5
Front Load Washing Machine
03D Series
Front Load Washing Machine
L614WD13
300
800
1400
2050
6
850X525X595
67
60
78
0.5
0.5
03D Series
1
SERVICE MANUAL
7
Chapter 3 Appearance brief introduction
Front Load Washing Machine
3-1. Name of parts
L614WD13
03D Series
595
525
850
SERVICE MANUAL
8
Chapter 4 Operational Guidance
Front Load Washing Machine
03D Series
¬Control panel lock function:
Press the "Delay" and the "Start/Pause" buttons simultaneously for 3 seconds after starting a program.Button Functions and wash cycle
will be unable to be changed. To unlock press the "Delay" and "Start/Pause" buttons again for 3 seconds.
.
Dry
.
L614WD13
90
60
40
1400
1000
800
400
Temp. Speed Intense
Start/Pause
Delay
20
Pre-Wash
Standard
Eco
Synthetic
Wool
Power
Cotton
Quick Wash
Mix
Delicate
Spin
Rinse
Dry
Dry
SERVICE MANUAL
9
Front Load Washing Machine
03D Series
¬To cancel a program
Press the "Start/Pause" button, then switch off the power and the program is automatically cancelled. Turn on the power and use the
program selector again to choose another program.
¬To cancel audible alarm
Alarm sound can be cancelled if it is required (not recommended)
Switch on the washing machine and turn the program knob to Spin/Drain cycle, then press the "Delay" and "Dry” button, hold on for
3 seconds.
The message "bEEP OFF” will be displayed on the screen, indicating that the alarm sound has been cancelled.
¬To reinstate audible alarm
Switch on the washing machine and turn the program knob to Spin/Drain cycle, then press the "Delay" and "Extra rinse " button, hold on for
3 seconds.The "bEEP On" message will be displayed on the screen, indicating that the alarm sound has been reinstated.
¬Power-off memory function
In case of abrupt power failure or the need to cut off the power during a program cycle, the present settings will be saved and the
preset operation will resume when the power is on again.
Press this button ,the "dry" indicator light will illuminate.When you select the washing programe first,
and then press this button,the machine will perform the washing and drying function.
K
SERVICE MANUAL
Chapter 5 Wiring circuit
Front Load Washing Machine
10
03D Series
SERVICE MANUAL
11
03D Series
AC
1.How to start
Press the “Temp.” and “Speed” button, at the same time, put plug in the socket, then LED will be on.Press“start/pause”
button, it will enter the model of the machine, then press the “start/pause” button again, it will implement the test function.
2.Test item
1)Door switch is closed for 3 seconds, “88:88” will display. If the door switch is open, “Err1” will display.
2)”77:77” will display, if the level of water reach the first level following these steps: firstly, the water is from the pre wash
valve for 5 seconds, secondly , the water is form the main wash valve for 5 seconds, thirdly, the water is from the hot water
valve for 5 seconds(if there is not hot water, this step ignores), then the water is from the soft water valve (in the mean,
the main wash valve and the prewash valve work at the same time) until the first level. “Err5” will dispaly, if the first level
does not reach after 2 minutes.(“Err8”will dispaly, if the first level indicates before the water coming from the valve, or it
showesreaching the overflown level).
3) The Heater works for 10 seconds, ”66:66” will display.
4) When the water runs out, “55:55” will be on. If there is water after 2 minutes, “Err2” will be on.
5) Drain Pump keep working, at the same time, the washing machine works 10s at the speed of 400rpm, then it keep 10s
at the speed of 1400rpm,“44:44” will be on.
Please press the “start/pause” botton or turn off the power when it need stop the program. If there is
something wrong, please deal with the trouble following the indication.
1.Press the “Speed” button, at the same time, put plug in the socket,then it will enter the model of the washing
machine.
2. “1490” dispalys on the screen, then press “Speed” button to choose the correct speed
1490/1480/1470/
” will be display by turn.
In order to save the right model, please press the “Temp.” button. Finally, please cut off the power when the
washing work is over.
Finally, please cut off the power when the washing work is over.
3. “1460” is the original edition before you choose the model.
4. The model will change as following “
1490/1480/1470/1460/1450/1290/1280/1270/1260/1250/1090/1080/
when you choose the model for the first time (from the
lager number to
5. For the model “L614WD13” Please choose “ 1460 ”
the little).The model can not change after you set up.
1460/14501290/1280/1270/1260/1250/1090/1080/1070/1060/1050
1070/1060/1050
ll
l
l
l
ll
l
l
l
l
l
l
ll
ll
l
SERVICE MANUAL
Front load Washing Machine
12
7-1
Chapter 7 Error Display and troubleshooting
03D Series
d
SERVICE MANUL
Haier Front Load Washing Machine
7-2. Error Display
Error message: Drainage error, water not emptied within 6 min.
Troubleshooting:
N
Check if drain pump acts by touching
pump position
Y
Check if drain pump or
drain pipe is jammed,
And open the filter and
clean
N
Cut off the power and choose spin
program to start ,then check the import
voltage of drain pump, is it between
AC 220-2240 V?
Replace drain pump
N
Cut off power and pull out water level
pressure switch wire connection. Set
spin program to start. Check the export
voltage to drain pump, is it between AC
220-240V?
Replace PCB
Y
Check if water is emptied
Y
Check if the pipe connected to the water level sensor
is jammed, If it is, clean the pipe. If not, replace PCB
N
Y
The wire between PCB
and drain pump is not
connected properly.
Replace the wire.
13
03D Series
Error message:Door is not properly shut 20s after program is started.
Troubleshooting:
Pushing the door to Check Whether
Door is properly shut or not
Y
Shut the door properly
Door lock is broken and need replacing,
then make sure wire is connected
properly.
Check the voltage between X1-2 and
X2-2 of PCB, is it between AC
220-240V?
Cut off the power and then turn on again.
Check the voltage between brown wire
and blue wire of door lock, is it between
AC 220-240V?
N
Replace
PCB
N
Connect the wire properly
Check if the wire connecting door lock
and PCB is loose
N
Y
Y
N
SERVICE MANUL
Haier Front Load Washing Machine
14
Error message:Temperature sensor is not properly connected or damaged.
Troubleshooting:
Error message:The heater may be broken(dispiay at the end of a program).
Troubleshooting:
N
NTC exist open circuit. Replace it
Y
Cut off power, check the resistance of
two pins of heater element by
multimeter, is it between 27-30
?
Heater element must
be broken, please
replace it
Y
Check if NTC is connected properly
Cut off power and measure the resistance
of temperature sensor by
multimeter,is
it between 5-14k
?
Y
N
Connect NTC well
N
N
The control wire may be broken,
Otherwise the PCB must be broken;
Please replace the broken.
N
Replace PCB
Check the wire
between NTC
and PBC, are they connected well?
Connect all wires well
Disconnect the two black wires from PCB
, and measure if the resistance
between the two black wires of PCB, is
it infinite?
Y
N
Y
Replace wire
Check if overload laundry. Reduce the laundry
Y
03D Series
SERVICE MANUL
Haier Front Load Washing Machine
15
Error message: The required water level is not reached within 8 min.
Troubleshooting:
N
Check if inlet valve is jammed
Clean inlet valve
N
Draw out the dispenser and check if
water is entering
Observe if the
height of drain pipe
not reach 80 cm. If
water level sensor
and the hose is
leaking gas
N
Turn on power, and set pre-wash
mode, then start. Check the import
voltage of electromagnetic valve by
multimeter is it between AC
220-240V?
Electromagnetic valve must be broken, please
replace it.
N
Check if tap is closed or water
pressure is too low (usual
between 0.03 -1 MPa)
Open the tap or wait for normal water
pressure to use
The wire connected PCB and inlet valve is not
properly. Please reconnect it or replace it.
Y
Y
Y
Y
Y
Check if water is leaking from washer
bottom. Inlet pipe. drain pipe or
other pipe connection
Y
Replace PCB
Check if export voltage from PCB to
electromagnetic valve
is it between AC 220-240V?
N
N
Connect it well.
03D Series
SERVICE MANUL
Haier Front Load Washing Machine
16
Error message. Motor speed is abnormal.
Troubleshooting:
Y
Cut off power and check if motor wires
are connected well
Reconnect well
Y
N
The motor is broken, replace it.
N
Switch on the power and check the
voltage(9 or 10 of motor connector) is
between 220-240V?
Replace the PCB
03D Series
SERVICE MANUL
Haier Front Load Washing Machine
17
Error message. Water level exceeds protection value.
TroubTroubleshooting: leshooting: Troubleshooting:
N
Check if the pipe connected to the
water level sensor is folded.
Unfold the
pipe connected
to the water level sensor
N
Check if the
pipe connected to the
water level sensor is jammed.
Clean the pipe connected
to the water level sensor
Y
Y
Without starting but electrifying, measure
the import voltage of inlet valve, is it
between AC 220-240V?
Replace PCB
Y
N
Without power ,connect inlet pipe to inlet
valve, then open the tap and observe if
water is entering in dispenser
Y
Replace inlet valve
03\D Series
SERVICE MANUL
Haier Front Load Washing Machine
18
03D Series
check the resistance of dry heating
tube by mulitimeter,is it between 27-
30
check the import voltage of dry heating
tube by mulitimeter,is it between 220-
240V
dry heating element error
SERVICE MANUL
Haier Front Load Washing Machine
19
03D Series
Replace the drying motor
Reconnect well
Error message dry motor error
Troubleshooting
Cut off power and check
if drying motor wires are
connected well
SERVICE MANUL
Haier Front Load Washing Machine
20
03D Series
Error message The PCB and the motor can not communicate
Troubleshooting
Are the lines between PC board and
drive board ok?
Can the indicator light on the drive
board flash?
Please connect the lines
or replace them.
replace the drive
board
replace the PC
board
/