Haier HVS1200 User manual

Brand: Haier

Model: HVS1200

Category: Washing machines

Type: User manual

This manual is also suitable for

HVS1000

Haier HVS1200 is a front-loading washing machine with a 5kg wash load capacity and a 300mm diameter porthole that can be opened at a 180-degree angle. It features a multi-gear speed controller, allowing you to select the appropriate spin speed for your laundry. The unique gasket design prevents residual water from accumulating, ensuring a hygienic wash. You can delay the start of the wash cycle for up to 24 hours, giving you flexibility in scheduling your laundry routine.

Front Load Washing Machine Model:HVS SERIES

FRONT LOADING WASHING MACHINE

Service Manual

Suited model:

HVS1000

HVS1200

Features

300mm diameter porthole, door may be open at a 180 degrees.

Class-A energy-saving; Homocentric tubs with higher energy efficiency

Multi-gear speed controller

Unique gasket design featuring no residual water hidden inside

Delay time adjustive

Large wash load capacity 5kg

Serial Number: Version: 1.00 Edition: 2007-3

SMHVS01

Front Load Washing Machine Model:HVS SERIES

Page 1

1 Contents----------------------------------------------------------------------------------------1

2 Product code illumination and series introduction-----------------------------------2

3 Features ---------------------------------------------------------------------------------------3

4 Specification ----------------------------------------------------------------------------------4

5 Matters Needing Attention----------------------------------------------------------------6

6 Installation ------------------------------------------------------------------------------------9

7 Net dimension -------------------------------------------------------------------------------11

8 Names of the parts-------------------------------------------------------------------------12

9 Operational Functions --------------------------------------------------------------------13

10 Program description table---------------------------------------------------------------15

11.Error display and Trouble shooting---------------------------------------------------16

12 Wiring circuit ------------------------------------------------------------------------------24

Contents

Front Load Washing Machine Model:HVS SERIES

Page 2

PRODUCT CODE ILLUMINATION AND SERIES INTRODUCTION

Model code rule description

Model identification˖

HVS

1200

Examples˖

HVS1200

It represents HVS series appearanc eˈ with big windowǃ180eopening windowǃ1200rpm spin

speed.Spin speed is adjustive from 0 to 1200rpmˈtemprature is also adjustive.

it’s controlled

by computer.

A˖Serial code

B˖Max spin speed

Front Load Washing Machine Model:HVS SERIES

Page 3

FEATURES

ƽ300mm diameter porthole, door may be open at a 180 degrees.

Facilitate view of wash process, facilitate unloading and easy to use with large port.

ƽMulti-gear speed controller

According to different costumingˈyou can slect corresponding spin speedˈfrom 0 to 1200 rpm.

ƽUnique gasket design featuring no residual water hidden inside.

By the unique gasketˈwashing machine can left no residual water hidden between outer drum and

board.

ƽDelay time adjustive.

According to different costumingˈyou can slect delay timeˈfrom 0.5h to 24h.



 

Page ˑ

Front Load Washing Machine Model:HVS SERIES

Removable compartment for liquid detergent



Delay timer

(from - to)

h 1-24 1-24

Self cleaning suds pump



Water inlet hose cold water / hot water

Water drain hose / -support







Adjustable feet n° 4 4

4. Safety systems

Auto door lock

ADL

Motor overheating protection

MOP



No heating without water

NHW



Auto water cool-down

(before drain 90°C boiled wa

AWC

Water protection

WRP

Acqua Stop kit

Child protection

5. Programs

1) COTT ON PREWASH (90°C/60°C/40°C/

)

n°

2) COTTON (60°C/40°C/

)

n°

3) SYNTHETIC (40°C/

)

n°

4)WOOL n°

5)CASHMERE n°

6)SILK n°

7)QUICK WASH n°

8)SINGEL WASH n°

9)SINGEL RINSE n°

10)Drain n°

11)Spin n°

Optional function keys

(additional program settings)

3URJUDP

button

ZLWKSRZHUVZLWFK



Start



pause

Extra ri

NH\

Strong wash

Load

Delay timer

VSHHG

WHPSHUDWXUH

Packing dimensions & loadability - -

Packing dimensions (H x W x D)

90×64×66 90×64×66

Gross weight

82 82

40' Container load

SFV

40' HC load capacity

SFV

208 208

Logistic / recicling information RS

Packing weight

Packing materials / Recycling symbols REzY REzY

Carton (weight)

Polistyren (weight)

1000 1000

Polyetylene foil (weight)

500 500

Other packing materials (weight)

Wood (weight)

Service - -

User instruction (languages)

D/F/I/GB/E/P/NL D/F/I/GB/E/P/NL

Max. failure rate (12 Months after sales to end







Front Load Washing Machine Model:HVS SERIES

Page 6



Matters Needing Attention

ƽ6DIHW\



.A separate earthed socket is required for the

power supply. The washing machine must be

positioned so that the plug is accessible.

2. Hold the plug and not the electric cable

when unplugging the washing machine.

3.Fuses in the power circuit should be rated for 15A.

If the supply cord is damaged, it must be replaced

by the manufacturer , its service agent or similarly

qualified persons in order to avoid a hazard.

4. Do not touch or use the washing machine bare-

footed or when the hands or feet are wet.

5.Do not use flammable detergent or dry clean

ing agent; do not use flammable spray in

close vicinity to the washing machine; do not

remove or insert the plug in the presence of

flammable gas.

6. The door of the washing machine will become hot

during the heating process. Avoid contact with the

door during the heating process. For safety, keep

children away from the washing machine.



.HHSFKLOGUHQDZD\IURPWKHSDFNLQJPDWHULDOVDIWHUXQSDFNHG

Front Load Washing Machine Model:HVS SERIES

Page 7

9.The carpet must not obstruct the ventilation

openings in the base of the washing machine.

.The washing machine should not be install-

ed outdoors or in a damp place. In the

event of water leakage or splashes allow

the machine to dry naturally.

10.Keep away from heat sources and direct sun-

light to prevent plastic and rubber components

from aging.

11.During installation, ensure that the electric

cable is not trapped by the washing machine

and avoid damage to the electric cable.

ƽDuring Use

1. Before use, check the joints of the filling hose, the

tap and the drainage hose for possible problems

from water pressure fluctuations. If joints are loose

or there is leakage, turn off the tap and repair. Do

not use the washing machine until the hoses are

properly fixed.



Keep the door slightly open when the washing

machine is not in use to prevent formation of

odors; do not cover the washing machine with

plastic cover so that inside dampness cannot

be kept in.

Matters Needing Attention

Front Load Washing Machine Model:HVS SERIES

Page 8



3. Do not place heavy, heating source or wet

articles on the top of the washing machine.

4. Do not hot wash foam rubber or sponge-like

materials.

6. Do not open the detergent distribution drawer

during the wash cycle..



7. The door is fitted with a self-lock device and will not open until

2~3 minutes after the washing machine stops. Do not force

the door open. Do not open the door if water level can reach

the porthole.

8.After each wash program, turn off the tap to

prevent leakage; and unplug the washing

machine and wipe clean the lower part of

the porthole.

Steel wires in bras will pop

out during washing; never

wash bras containing steel

wires.

5. Before washing, do up zippers, buttons and

clothes straps and put small articles, such as

socks, laces or bras, into a washing bag or a

pillow.

Matters Needing Attention

Front Load Washing Machine Model:HVS SERIES

Page 9

5HPRYHDOOWKHSDFNLQJPDWHULDOVLQFOXGLQJWKHIRDPEDVH

WRSUHYHQWYLEUDWLRQGXULQJXVHDVVKRZQLQ)LJ

8SRQRSHQLQJRIWKHSDFNDJHZDWHUGURSVPD\EHVHHQRQWKH

SODVWLFEDJDQGWKHSRUWKROH7KLVLVQRUPDOSKHQRPHQRQ

UHVXOWLQJIURPZDWHUWHVWLQWKHIDFWRU\

Fig

Check attachments and materials with reference to the following

Dismantle the packing bolts as shown in Fig. 2.

The packing bolts are designed for clamping anti-vibration components

inside of the washing machine during the transportation process.

Beforeuse:

1. Remove the back plate;

2. Remove the three packing bolts on the back plate and take out the

rubber hose;

3. Replace the back plate;

4. Fill the holes left by the packing bolts with plastic plugs.

(Attention: The packing bolts and rubber hose should be kept in a safe

place for later use)

Fig

Adjusting the washing machine

There are adjustable feet under the bottom of the washing machine.

Before use, the washing machine should be adjusted, as shown in

Fig. 3, so that it is level.

Fig.



4XW\

1DPH

2SHUDWLRQ

PDQXDO





4XDOLW\

FHUWLILFDWH

:DWHU

KRVH

'UDLQDJH

KROGHU

3ODVWLF

SOXJV

Installation

Front Load Washing Machine Model:HVS SERIES

Page 10

FP

FP



The height of the drainage outlet must be 80-100cm. To prevent the drainage hose from dropping off,

fix it to the drainage hose clip at the back of the washing machine.

Before connecting to the power supply, check: 

Joining the Inlet Hose to the Washing Machine

Connect of water inlet valve

:DWHULQOHWKRVHRXW



1. Connect the nut on the inlet hose to the connector on the water valve.

7LJKWHQWKHQXWWRVHFXUHWKHKRVH

Installation

'UDLQDJH+RVH

Use the drainage holder to keep the end of the drainage hose retained and to prevent the outflow

of water . It is recommended that drainage hose extensions not be used; if an extension is needed,

please consult a serviceman. The additional hose should be no more than 250cm (overextended

hoses could lead to siphonage). Note: The drainage hose should not be submerged in water and

should be securely fixed and leak-free.The appliance is to be connected to the waster mains using

new hose-sets and that old hose-sets should not be reused.

Connecting to the Power Supply

The socket is adequate for the maximum power of the washing machine (For safety, fuses in the power circuit should be rated

for no less than 15A).

The power outlet should be capable of accepting the washing machine plug. The washing machine must be earthed before

use.

Supplementary earth cable should not be necessary if the socket is connected to the earth

Supplementary earth cable shoulde be installed on the upper back of the washing machine andconnected to an earth if the

power supply socket has no earth connection

The voltage should meet the requirement.

Front Load Washing Machine Model:HVS SERIES

Page 11

height: 850mm / width: 595mm / depth:400mm

595

850

400

NET DIMENSION

Front Load Washing

Machine Model:HVS SERIES

Page 12

Names of the parts

Top

Handle

Program selector

Detergent dispenser

Door

Porthole

Function selector

Bottom planel

ON/OFF button

Front Load Washing Machine Model:HVS SERIES

Page 13

Spin-dry

Pre-

wash

Display Information Introduction

A. Power On /Off Key

Press the key and the washer will be automatically ene

rgized, release the key and power

is discon nected.

B. Program Selection Knob

Turn the knob clockwise/counterclockwise to select the desired program. (please refer to

Program Setting Guidance Table for details)

C. Detergent Distribution B ox- See Figure a for the drawer- type Detergent Dispenser

Open the dispenser box and you will see four detergent compartment of 1, 2, 3:

Compartment 1: Pre-wash Detergent

Compartment 2: Washing Detergent

Compartment 3:Softener , Conditioner and Perfume

D. Reservation Selection K ey

Press the key to select the desired time when the washing progress completes. When

setting this feature, the indicator lamp on the upper left corner of the key will illuminate.

Time reservation range is from 1 to 24 hours. The reserved ti me will increase by one

ho ur at each press of the key. When t he feature is set, press Start/Pause key and the

reservetimewillbedisplayedandcountdownwillstart.Atthesametime,reservation

indicator lamp will start blinking and will go off after th e washer enters into normal

washing progress.

Figure a

Control Panel Function Description



Baby care

ⳳ㑪

Slik

Quick wash

Single wash

Rinse

Drain

Spin

Power

Slim 5

HVS1000

Cotton prewash

Cotton

Synthetic

Wool

Cashmere

㕞㑪

㕞↯

࣪㑪

ẝ咏

ẝ㑪⋫

䗳⋫

ⓖ

ᥦ∈㒛

㑪∈

㑪㑪

Tim e

Delay time

Rinse hold Temp. Speed

Start/Pause

Front Load Washing Machine Model:HVS SERIES

Page 15

Defau lt Program Detergent Usage MethodProgram

Settin g

Mode

Recommended

Laundry

Capacity Temperature

Total

Time

Temperature

Adjustment

Range

Rinse

Hold

Load

Selection

Baby

Care

Reserve

Compartment

Cotton

Pre-wash

Heavily-soiled

Cotton Fabrics

560

1200

1000

900

800

3:12

-40-50-

60-90

-40-50-

60-90

-40-50-

-40

-40-50-

YES YES YES YES

ƾƾ

嗟

Cotton

Cotton Fabrics 5 60 2:58 YES YES YES YES X

嗟

Synthetic

Fsat-colour-

Fiber

3 60 80 0 1:42 YES YES YES YES X

嗟

Cashmere

/ 40 600 1:10 YES NO YES YES X

嗟

/ 40 400 1:10 YES NO YES YES X

嗟

Slik

Silk

/ 40 400 1:05 YES NO YES YES X

/ _ _ 800 0:29 YES NO NO YES X

嗟

Rinse

5400 1:33 NO YES NO YES X

5 800 0:25 / YES YES YES YES XX

嗟

Drain

////0:03 / NO NO NO YES XXX

Spin

///

1200

1000

900

800

0:09 / NO NO NO YES XXX

Note:

嗟

means that it needs to add perfume such as softener

means that it needs to add

detergent otherwise the

desired washing result will not be achieved. X means it must not add

detergent. The data in Speed column is default spin speed of corresponding model (whe

speed is n o t selected.)

Note: 1. Washing t emperature refers to the hi ghest temperature allowable during the whole

wash ing process. The washing time varies according to the type of clothes, selected

temperature and feature. The total operation time provid ed in the above table is for

reference only (There will be a slight difference due to different water temperature.)

2. For clothes made of special materials such as wo olens, cashm ere and wool, please check if the

clothes has a machine

washing tag and the requests to the temperature.

Quick wash

Slightly-soiled

Textiles

Slightly-soiled

Textiles

Slightly-soiled

Textiles

Single

wash

Wool Wool

1200

1000

900

800

Front Load Washing Machine Model:HVS SERIES

Page

HVS SERIES Error Display and Troubleshooting

Error message:Door is not properly shut 20s after program is started.

Troubleshooting:

Pushing the door to Check Whether Door

is properly shut or not

Error message:Drainage error, water not emptied within 4 min.

Troubleshooting:

Cutoffthepowerandthenturnonagain.

Check the voltage between brown wire and

blue wire of door lock, is it between AC

220-240V?

Door lock is broken and need

replacing, then make sure wire is

connected properly.

Check the voltage between brown wire

and blue wire of PCB, is it between AC

220-240V?

Check if drain pump acts by touching

pump position

Check if drain pump or

drain pipe is jammed, and

open the filter and clean

Cut off the power and choose spin program to

start, then check the import voltage of drain

pump, is it between AC 220-240V?

Replace drain pump

Cut off power and pull out water level

pressure switch wire connection. Set spin

program to start. Check the export voltage to

drain pump, is it between AC 220-240V?

Replace PCB

Replace

PCB

Connect the wire properly

Check if the wire connecting door lock

and PCB is loose .

Check if water is emptied

Cut off power and water level pressure switch wire

connection, measure the resistance of 1 and 3 pin, is it

infinite? If not, it is water level pressure switch failure

andreplaceit.Ifitis,thenrepairandcheckPCBand

wire as followed.

The wire between

PCB and drain

pump is not

connected

properly.

Replace the wire.

220-240v

Shut the door properly.

220-240v

PCB

Front Load Washing Machine Model:HVS SERIES

Page 17

Error message:Temperature sensor is not properly connected or damaged (display at the end of a

program).

Troubleshooting:

Error message:The heater may be broken

Troubleshooting:

NTC exist open circuit .Replace it

Cut off power, check the resistance of

two pins of heater element by multimeter,

is it between 32-35

Heater element

must be broken,

please replace it

Check if NTC is connected properly

Cut off power and measure the resistance

of temperature sensor by multimeter, is

it between 5-14k

Connect NTC well

Check the

black wires of NTC,

are they connected well?

Disconnect

from PCB,

and measure if the resistance

between

of PCB is

it infinite?

Replace PCB

Connect all wires well

Replace wire

PCB

two

the two black wires

The control wire may be broken,

otherwise PCB must be broken.

Please replace the broken one.

Front Load Washing Machine Model:HVS SERIES

Page 18

Error message:The required water level is not reached within 8 min

Troubleshooting:

Check if inlet valve is jammed

Clean inlet valve

Draw out the dispenser and check if water is

entering

Observe if the height of

drain pipe not reach 80

cm. If water level

pressuresswitchand

the hose is leaking gas

Turn on power, and set pre-wash mode, then

start. Check the import voltage of

electromagnetic valve by multimeter,

is it between AC 220-240V?

Electromagnetic valve must be broken, please replace

it.

Check if tap is closed or water pressure is too

low (usual between0.2 -1 MPa)

Open the tap or wait for normal wat er pressure to use

The wire connected PCB and inlet valve is not

properly. Please reconnect it or replace it.

Check if water is leaking from washer

bottom. inlet pipe. drain pipe or other

pipe connection

Readjust or replace the broken parts

Replace PCB

Check if export voltage from PCB to

electromagnetic valve, is it between AC

220-240V?

220-240V

Page 19

Page is loading ...

Haier HVS1200 User manual

Brand: Haier

Model: HVS1200

Category: Washing machines

Type: User manual

This manual is also suitable for

HVS1000

Download PDF

report

Haier HVS1200 User manual

This manual is also suitable for

Haier HVS1200 User manual

Related papers

Other documents