Thank you for purchasing this quality product. Be sure to check all
packing material carefully for small parts, which may have came
loose inside the carton during shipment. Count all parts and material
hardware, then compare with parts list to be sure all parts are
present. If any parts are missing or damaged, phone, fax, or mail to
our Customer Service Department for efficient and speedy service.
Please indicate the model number and code letter of part(s) needed.
IMPORTANT NOTE: Follow instructions listed below in proper
sequence as numbered to assure fast,easy and correct assembly.
LEFT SIDE PANEL-1PC
TOP PANEL-1PC
2/10
c
b
SHOULDER
NOTE: UPON OPENING, THOROUGHLY CLEAN ALL WOOD SURFACES TO REMOVE DUST
AND DIRT THAT MAY HAVE SETTLED ONTO THE FINISH DURING SHIPMENT. IN
ORDER TO PREVENT DAMAGE DURING ASSEMBLY. PLEASE ASSEMBLE THIS ITEM
WITH AT LEAST TWO PEOPLE.
HOW TO USE THE CAM-TOOL
NOTE
:
THE ARROWS ON THE HIDDEN CAM-LOCKS SHOULD POINT TO THE CAM-BOLTS.
ARROW
NOTE: TURN THE CAM-BOLT SCREWS UNTIL THEY
ARE TIGHT, THE SHOULDER SHOULD BE
AGAINST THE SURFACE OF THE PART.
ARROW
4/10
● INSTALL THE WOOD DOWEL (a) AND THE CAM LOCK BOLT (b) INTO THE FIXED SHELF (C).
JOIN THE DIVIDER (I) TO THE FIXED SHELF (C) BY USING THE WOOD DOWEL (a) FIRST.
● ONCE JOINED, TIGHTEN CAM LOCK (c) ONTO BOLT (b) USING PRE-DRILLED HOLES.
COVER CAM HOLES WITH THE SHORT PLASTIC COVER (f).
FIG 1
5/10
FIG 2
● INSTALL THE WOOD DOWEL (a) AND THE CAM LOCK BOLT (b) INTO THE LEFT SIDE PANEL (A)
AND THE RIGHT SIDE PANEL (B).
● JOIN THE LEFT SIDE PANEL (A) AND THE RIGHT SIDE PANEL (B) INTO THE FIXED SHELF
(C), THE LOWER BACK CROSS BAR (D), THE UPPER BACK CROSS BAR (E), AND THE UPPER
FRONT CROSS BAR (F) BY USING THE WOOD DOWEL (a) FIRST.
● ONCE JOINED, TIGHTEN CAM LOCK (c) ONTO BOLT (b) USING PRE-DRILLED HOLES.
● COVER CAM HOLES WITH THE LONG PLASTIC COVER (k).
6/10
FIG 3
● INSTALL THE WOOD DOWEL (a) AND THE CAM LOCK BOLT (b) INTO THE TOP PANEL (G).
● JOIN THE TOP PANEL (G) TO THE ASSEMBLED PART BY USING THE WOOD DOWEL (a) FIRST .
● ONCE JOINED, TIGHTEN CAM LOCK (c) ONTO BOLT (b) USING PRE-DRILLED HOLES.
● COVER CAM HOLES ON THE DIVIDER (I) WITH THE SHORT PLASTIC COVER (f).
● COVER CAM HOLES ON THE LEFT SIDE PANEL (A) AND THE RIGHT SIDE PANEL (B) WITH
THE LONG PLASTIC COVER (k).
●TIGHTEN THE UPPER FRONT CROSS BAR (F) BY USING THE 1”L FLAT HEAD SCREW (e).
7/10
FIG 4
● ATTACH THE HOOK (j) TO THE ASSEMBLED PART BY USING THE 1/2”L FLAT HEAD SCREW (i).
8/10
FIG 5
● TIGHTEN THE BACK PANEL (H) BY USING THE 1/2”L ROUND HEAD SCREW (d) AND 1"L FLAT
HEAD SCREW (e).
9/10
FIG 6
● USE THE PROPER HARDWARE FOR YOUR WALL TYPE DRILL 1/4” HOLES.
INSERT THE PLASTIC ANCHOR (h) INTO THE WALL.
● SCREW THE 2" L FLAT HEAD SCREW (g) INTO THE FIXED PLASTIC ANCHOR (h).
HANG THE ASSEMBLED WELLMAN WALL SHELF ONTO THE WALL.
10/10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Home Decorators Collection 1158110960 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Home Decorators Collection 9249900270 Operating instructions
-
-
Unbranded 1061110910 Operating instructions
-
-
-
-
-
-
-