Thank you for purchasing this quality product. Be sure to check all
packing material carefully for small parts, which may have came
loose inside the carton during shipment. Count all parts and material
hardware, then compare with parts list to be sure all parts are
present. If any parts are missing or damaged, phone, fax, or mail to
our Customer Service Department for efficient and speedy service.
Please indicate the model number and code letter of part(s) needed.
IMPORTANT NOTE: Follow instructions listed below in proper
sequence as numbered to assure fast,easy and correct assembly.
2/18
TOP PANEL-1PC
FIXED SHELF-1PC
c
b
SHOULDER
NOTE: UPON OPENING, THOROUGHLY CLEAN ALL WOOD SURFACES TO REMOVE DUST
AND DIRT THAT MAY HAVE SETTLED ONTO THE FINISH DURING SHIPMENT. IN
ORDER TO PREVENT DAMAGE DURING ASSEMBLY. PLEASE ASSEMBLE THIS ITEM
WITH AT LEAST TWO PEOPLE.
HOW TO USE THE CAM-TOOL
NOTE
:
THE ARROWS ON THE HIDDEN CAM-LOCKS SHOULD POINT TO THE CAM-BOLTS.
ARROW
NOTE: TURN THE CAM-BOLT SCREWS UNTIL THEY
ARE TIGHT, THE SHOULDER SHOULD BE
AGAINST THE SURFACE OF THE PART.
ARROW
5/18
● TIGHTEN THE HOOK (l) ONTO THE TOP MIRROR FRAME (C) BY USING THE 1/2” FLAT HEAD
SCREW (m) THROUGH PRE-DRILLED HOLES.
FIG 1
6/18
● INSTALL THE WOOD DOWEL (a) AND THE CAM LOCK BOLT (b) INTO THE TOP PANEL (G).
● JOIN THE TOP PANEL (G) TO THE ASSEMBLED PART AND ONCE JOINED, TIGHTEN CAM
LOCK (c) ONTO BOLT (b) USING PRE-DRILLED HOLES.
● COVER CAM HOLES WITH THE LONG PLASTIC COVER (k).
● TIGHTEN THE TOP PANEL (G) AND THE TOP MIRROR FRAME (C) BY USING THE 1-1/2”L
FLAT HEAD SCREWS (h).
FIG 3
8/18
● JOIN THE BACK SUPPORT SLATS (D) TO ASSEMBLED PART BY USING THE WOOD DOWEL (a).
FIG 4
9/18
● ATTACH MAGNETS (i) TO THE FIXED PANEL (H) BY USING 5/8”L ROUND HEAD SCREW (d)
THROUGH PRE-DRILLED HOLES.
FIG 5
10/18
● TIGHTEN THE FIXED PANEL (H) THE ASSEMBLED PART BY USING THE WOOD DOWEL (a).
● TIGHTEN THE FIXED PANEL (H) TO ASSEMBLED PART BY USING THE 1-1/2”L FLAT HEAD
SCREW (h) THROUGH PRE-DRILLED HOLES ON BOTTOM OF THE FIXED PANEL (H).
FIG 6
11/18
● INSTALL THE WOOD DOWEL (a) AND THE CAM LOCK BOLT (b) INTO THE DIVIDER (I).
● JOIN THE FIXED SHELF (K) TO THE DIVIDER (I) BY USING THE WOOD DOWEL (a) FIRST.
● ONCE JOINED, TIGHTEN CAM LOCK (c) ONTO BOLT (b) USING PRE-DRILLED HOLES.
FIG 7
12/18
● INSTALL THE WOOD DOWEL (a) AND THE CAM LOCK BOLT (b) INTO BOTTOM PANEL (L).
● JOIN THE ASSEMBLED PART AND THE LOWER SIDE PANEL (J) TO THE BOTTOM PANEL (N)
BY USING THE WOOD DOWEL (a) FIRST.
● ONCE JOINED, TIGHTEN CAM LOCK (c) ONTO BOLT (b) USING PRE-DRILLED HOLES.
● COVER CAM HOLES WITH THE SHORT PLASTIC COVER (e).
FIG 9
14/18
● INSTALL THE WOOD DOWEL (a) AND THE CAM LOCK BOLT (b) INTO BOTTOM OF
THE FIXED PANEL (H).
● JOIN TWO ASSEMBLED PARTS BY USING THE WOOD DOWEL (a) FIRST.
● ONCE JOINED, TIGHTEN CAM LOCK (c) ONTO BOLT (b) USING PRE-DRILLED HOLES.
● COVER CAM HOLES WITH THE SHORT PLASTIC COVER (e).
FIG 10
15/18
● TIGHTEN THE CENTER UPPER BACK PANEL (F), THE SIDE UPPER BACK PANEL (E),
THE BOTTOM BACK PANEL (P), AND THE METAL PLATE (n) BY USING THE 5/8” L ROUND
HEAD SCREW (d).
FIG 11
16/18
● ATTACH THE LEFT DOOR (M) AND THE RIGHT DOOR (N) TO THE ASSEMBLED PART
BY USING 1/2” FLAT HEAD SCREW (m).
● TIGHTEN THE KNOB (f) TO THE LEFT DOOR (M) AND THE RIGHT (N) BY USING THE KNOB
BOLT (g).
FIG 12
17/18
● PLACE THE SHELF PIN (j) IN DESIRED POSITION AND PLACE THE ADJUSTABLE SHELF (O)
ABOVE THE SHELF PIN (j).
FIG 13
18/18
/