ESAB A2 Tripletrac User manual

Brand: ESAB

Model: A2 Tripletrac

Category: Welding System

Type: User manual

ESAB A2 Tripletrac is a three-wheeled automatic welding machine designed for submerged arc welding with solid or flux-cored wire. It offers flexible welding possibilities for longitudinal and circumferential welding. The separate wire feeder ensures easy handling and accurate wire feeding. Additional equipment is available for submerged arc welding with strip electrodes.

Valid for serial no. 320--xxx--xxxx0449 435 001 2005--09--06

A2 Automatic

welding machine

(three-wheeled)

A2 Tripletrac

101103105107109111102021110025108024042106023061104022041100020040060001

Bruksanvisning

Brugsanvisning

Bruksanvisning

Käyttöohjeet

Instruction manual

Betriebsanweisung

Manuel d’instructions

Gebruiksaanwijzing

Instrucciones de uso

Istruzioni per l’uso

Manual de instruções

Ïäçãßåò ÷ñÞóåùò

-- 2 --

Rätt till ändring av specifikationer utan avisering förbehålles.

Ret til ændring af specifikationer uden varsel forbeholdes.

Rett til å endre spesifikasjoner uten varsel forbeholdes.

Oikeudet muutoksiin pidätetään.

Rights reserved to alter specifications without notice.

Änderungen vorbehalten.

Sous réserve de modifications sans avis préalable.

Recht op wijzigingen zonder voorafgaande mededeling voorbehouden.

Reservado el derecho de cambiar las especificaciones sin previo aviso.

Ci riserviamo il diritto di variare le specifiche senza preavviso.

Reservamo--nos o direito de alterar as especificações sem aviso prévio.

Äéáôçñåßôáé ôï äéêáßùìá ôñïðïðïßçóçò ðñïäéáãñáöþí ×ùñßò ðñïåéäïðïßçóç.

SVENSKA 5..............................................

DANSK 19................................................

NORSK 33................................................

SUOMI 47................................................

ENGLISH 61..............................................

DEUTSCH 75.............................................

FRANÇAIS 89.............................................

NEDERLANDS 103.........................................

ESPAÑOL 117..............................................

ITALIANO 131..............................................

PORTUGUÊS 145..........................................

ÅËËÇÍÉÊÁ 159.............................................

-- 3 --

FÖRSÄKRAN OM ÖVERENSSTÄMMELSE

ESAB AB, Welding Automation, SE--695 81 Laxå, Sverige, försäkrar under eget ansvar att svetsauto-

mat A2 Tripletrac från serienummer 320 är i överensstämmelse med standard IEC/EN 60292 och

IEC/EN 60204 enligt villkoren i direktiv (98/37/EG) och standard EN 50199 enligt villkoren i direktiv

(89/336/EEG) med tillägg (93/68/EEG).

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- ------------------------------------

OVERENSSTEMMELSEERKLÆRING

ESAB AB, Welding Automation, SE--695 81 Laxå, Sverige, erklærer på eget ansvar, at svejseautomat

A2 Tripletrac fra serienummer 320 er i overensstemmelse med standarden IEC/EN 60292 og IEC/

EN 60204 ifølge betingelserne i direktiv (98/37/EØF) og standarden EN 50199 ifølge betingelserne i

direktiv (89/336/EØF) med tillæg (93/68/EØF).

FORSIKRING OM SAMSVAR

Esab Welding Equipment AB, SE--695 81 Laxå, Sverige, forsikrer på eget ansvar at sveiseautomat

A2 Tripletrac fra serienummer 320 er i overensstemmelse med standard EN 60292 og EN 60204 i

følge vilkårene i direktiv (98/37/EF) og standard EN 50199 i følge vilkårene i direktiv (89/336/EF) med

tillegg (93/68/EF).

VAATIMUSTENMUKAISUUSVAKUUTUS

ESAB AB, Welding Automation, SE--695 81 Laxå, Ruotsi, vakuuttaa omalla vastuullaan, että

hitsausautomaatti A2 Tripletrac alkaen sarjanumerosta 320 täyttää standardin IEC/EN 60292 ja

IEC/EN 60204 vaatimukset direktiivin (98/37/ETY) ehtojen mukaisesti sekä standardin EN 50199 vaa-

timukset direktiivin (89/336/ETY) ja sen lisäysten (93/68/ETY) ehtojen mukaisesti.

DECLARATION OF CONFORMITY

ESAB AB, Welding Automation, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that

automatic welding machine A2 Tripletrac from serial number 320 complies with standard

IEC/EN 60292 and IEC/EN 60204, in accordance with the requirements of directive (98/37/EEC) and

with standard EN 50199, in accordance with the requirements of directive (89/336/EEC) and adden-

dum (93/68/EEC).

ZULASSUNGSNACHWEIS

ESAB AB, Welding Automation, SE--695 81 Laxå Schweden, bestätigt hiermit in Eigenverantwortung,

daß der Schweißautomat A2 Tripletrac ab Seriennummer 320 dem Standard IEC/EN 60292 und

IEC/EN 60204 gemäß den Bedingungen der Direktive (98/37/EEG) und dem Standard EN 50199 ge-

mäß den Bedingungen der Direktive (89/336/EEG) mit Zusatz (93/68/EEG) entspricht.

CERTIFICAT DE CONFORMITÉ

ESAB AB, Welding Automation, SE--695 81 Laxå, Suède, certifie que la appareil de soudage

automatique A2 Tripletrac à partir du numéro de série 320 est conforme à la norme IEC/EN 60292 et

IEC/EN 60204 selon les conditions de la directive (98/37/CEE) et à la norme EN 50199 selon les

conditions de la directive (89/336/CEE) avec additif (93/68/CEE).

VERKLARING VAN OVEREENSTEMMING

ESAB AB, Welding Automation, SE--695 81 Laxå Zweden, verklaart geheel onder eigen verantwoor-

delijkheid dat lasautomaat A2 Tripletrac van het serienummer 320 in overeenstemming is met norm

IEC/EN 60292 en IEC/EN 60204 conform de bepalingen in richtlijn (98/37/EEG) en met norm

EN 50199 conform de bespalingen in richtlijn (89/336/EEG) met annex (93/68/EEG).

DECLARACIÓN DE CONFORMIDAD

ESAB AB, Welding Automation, SE--695 81 Laxå, Suecia, garantiza bajo propia responsabilidad que

la equipo para soldadura automática A2 Tripletrac a partir del número de serie 320 concuerda con la

norma IEC/EN 60292 y IEC/EN 60204 conforme a la directiva (98/37/CEE) y con la norma EN 50199

según los requisitos de la directiva (89/336/CEE) con el suplemento (93/68/CEE)

DICHIARAZIONE DI CONFORMITA

ESAB AB, Welding Automation, SE--695 81 Laxå Svezia, dichiara sotto la propria responsabilità che

la saldatrice automatica A2 Tripletrac con numero di serie a partire da 320 è conforme alla norma

IEC/EN 60292 e IEC/EN 60204 come previsto dalla direttiva (98/37/CEE) ed alla norma EN 50199

come previsto dalla direttiva (89/336/CEE) e successive integrazioni (93/68/CEE).

-- 4 --

DECLARAÇÃO DE CONFORMIDADE

ESAB AB, Welding Automation, SE--695 81 Laxå Suécia, garante sob responsabilidade própria que,

o equipamento automático para soldadura A2 Tripletrac a partir do número de série 320 está em

conformidade com a norma IEC/EN 60292 e IEC/EN 60204 segundo os requisitos da directiva

(98/37/CEE) e com a norma EN 50199 segundo os requisitos da directiva (89/336/CEE) com o suple-

mento (93/68/CEE).

ÄÇËÙÓÇ ÓÕÌÌÏÑÖÙÓÇÓ

ÇåôáéñåßáESAB AB, Welding Automation, SE--695 81 Laxå, Óïõçäßá, äçëþíåé üôé ôá ìç÷áíÞìáôá

áõôüìáôò óõãêïëëçôÞò A2 Tripletrac áðü ôïí áñéèìü óåéñÜò 320 êáé Ýðåéôá, óõììïñöþíïíôáé

ìå ôï ðñüôõðï IEC/EN 60292 êáé IEC/EN 60204 óýìöùíá ìå ôéò áðáéôÞóåéò ôçò ïäçãßáò

(98/37/EEG) êáé ôï ðñüôõðï EN 50199 óýìöùíá ì å ôéò áðáéôÞóåéò ôçò ïäçãßáò (89/336/EEG) êáé

ôïõ ðáñáñôÞìáôïò (93/68/EEG).

Henry Selenius

Managing Director

ESAB AB, Welding Automation

SE--695 81 LAXÅ

SWEDEN Tel: + 46 584 81000 Fax: + 46 584 411721

Laxå 2003--11--20

ENGLISH

-- 6 1 --

TOCe

1SAFETY 62...........................................................

2 INTRODUCTION 64...................................................

2.1 General 64..................................................................

2.2 Welding Method 64...........................................................

2.3 Definitions 64................................................................

2.4 Technical data 64............................................................

2.5 Main components 65.........................................................

2.6 Description of Main Components 66............................................

3 INSTALLATION 67....................................................

3.1 General 67..................................................................

3.2 Mounting 67.................................................................

3.3 Adjusting the brake hub 67....................................................

3.4 Connections 68..............................................................

4 OPERATION 69.......................................................

4.1 General 69..................................................................

4.2 Loading the welding wire 70...................................................

4.3 Changing the feed roller 70....................................................

4.4 Contact equipment 71........................................................

4.5 Refilling with flux powder 71...................................................

4.6 Placing the Control Unit PEH 71................................................

4.7 T ransportation of the Automatic Welding Machine 72..............................

5 MAINTENANCE 73....................................................

5.1 General 73..................................................................

5.2 Daily 73.....................................................................

5.3 Periodic 73..................................................................

6 TROUBLESHOOTING 74..............................................

6.1 General 74..................................................................

6.2 Possible faults 74............................................................

7 ORDERING OF SPARE PARTS 74......................................

DIMENSION DRAWING 173................................................

ACCESSORIES 174.......................................................

SPARE PARTS LIST 175...................................................

-- 6 2 --

SafE

1SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding equipment. The following recommen-

dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

S its operation

S location of emergency stops

S its function

S relevant safety precautions

S welding

2. The operator must ensure that:

S no unauthorised person is stationed within the working area of the equipment when it is

started up.

S no--one is unprotected when the arc is struck

3. The workplace must:

S be suitable for the purpose

S be free from draughts

4. Personal safety equipment

S Always wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

S Make sure the return cable is connected securely.

S Work on high voltage equipment may only be carried out by a qualified electrician.

S Appropriate fire extinquishing equipment must be clearly marked and close at hand.

S Lubrication and maintenance must not be carried out on the equipment during operation.

-- 6 3 --

SafE

WARNING

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-

TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE

BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

S Install and earth the welding unit in accordance with applicable standards.

S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

S Insulate yourself from earth and the workpiece.

S Ensure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

S Keep your head out of the fumes.

S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.

S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

S Protect bystanders with s uitable screens or curtains.

FIRE HAZARD

S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

S Protect your ears. Use earmuffs or other hearing protection.

S Warn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

-- 6 4 --

fhb7d1ea

2 INTRODUCTION

2.1 General

The A2 Tripletrac automatic welding machine is designed for Submerged Arc

Welding of butt and fillet joints.

All other applications are prohibited.

The A2 Tripletrac is intended for use in combination with control box

A2--A6 Process Controller (PEH) or A2 Welding Control Unit ( PEI) and ESAB’s

welding power sources LAF or TAF.

2.2 Welding Method

2.2.1 Submerged Arc Welding (SAW)

This version can be equipped with feed rollers for single wire welding. A special

knurled feed roller is available for flux--cored wire, which guarantees even wire feed

without the risk of deformation due to high feed pressure.

2.3 Definitions

SAW welding The weld bead is protected by a cover of flux during the welding.

2.4 Technical data

A2 TF (UP)

Supply voltage 42 V AC

Permissible load at 100 %: 800 A DC

Wire dimensions:

hollow wire

1.6--4.0 mm

Wire feed speed, max 9m/min

Brake hub braking torque 1.5 Nm

T ravel speed 0.1--2.0 m/min

Turning radius for circumferential welding, min 1500 mm

Pipe diameter for internal joint welding, min 1100 mm

Max. weight of wire 30 kg

Flux container volume (Not to be filled with preheated flux) 6l

Weight (excl. wire and flux) 68 kg

Inclination sideways, max. (the whole unit)

Inclination backwards, max. (the whole unit)

15_

-- 6 5 --

fhb7d1ea

2.5 Main components

1. Carriage

2. Carrier

3. Wire feed unit

4. Slide kit, manual

5. Contact tube

6. Wire feed motor

7. Guide pin

8. Flux hopper

9. Flux tube

10. Control box PEH or PEI

11. Water level

See on page 66 for a description of the m ain components.

-- 6 6 --

fhb7d1ea

2.6 Description of Main Components

2.6.1 Carriage

The carriage is provided with 2--wheel drive.

For manual transport disengage the wheels with

locking lever ( 1).

Tr avel direction is set with the hand wheel (2)

2.6.2 Carrier

The control box, wire feed unit and flux hopper,

among other things, are to be fitted on the carrier.

2.6.3 Wire Feed Unit

The unit is used for guiding and feeding the welding wire down into the contact tube.

2.6.4 Manual Slides

The horizontal and vertical position of the welding head is adjusted by way of linear

slides. The angular motion can be freely adjusted using the rotary slide.

2.6.5 Contact Tube

Tr ansfers welding current to the wire during welding.

2.6.6 Wire Feed Motor

The wire feed motor is used for feeding the welding wire.

2.6.7 Guide Pin

The guide pin is used to help positioning the welding head in the joint.

2.6.8 Flux Hopper / Flux Tube

The flux is filled into the flux hopper and is then transferred to the workpiece through

the flux tube.

The amount of flux to be dropped down is controlled by way of the flux valve fitted to

the flux hopper.

See “Refilling with flu x on page 71.

2.6.9 Control box

A2--A6 Process Controller (PEH), see instruction manual 0443 745 xxx

A2 Welding Control Unit ( PEI), see instruction m anual 0449 331 xxx.

2.6.10 Water L evel

Check the inclination of the automatic welding machine using the water level.

For max. inclination, see Technical Data on page 64.

-- 6 7 --

fhb7i1ea

3 INSTALLATION

3.1 General

The installation must be execu ted by a profession al.

WARNING

Rotating parts can cause injury, take great care.

3.2 Mounting

3.2.1 Wire drum ( Accessories)

Wire drum (1) is mounted on the brake hub ( 2).

S Check that the carrier (3) is pointing upwards.

NOTE! The maximum angle for the wire bobbin is 25°.

At extr em e angles, wear will occur on the brake hub

locking mechanism and the wire bobbin will slide off

the brake hub.

WARNING

To prevent the r eel sliding off the hub:

Lock the reel in place by turning the red knob as shown

on the warning label attached next to the hub.

3.3 Adjusting the brake hub

The brake hub is adjusted when delivered, if readjustment

is required, follow the instructions below. Adjust the brake

hub so that wire is slightly slack when wire feed stops.

S Adjusting the braking torque:

S Turn the red handle to the locked

position.

S Insert a screwdriver into the springs in the hub.

Turn the springs clockwise to reduce the braking torque

Turn the springs anticlockwise to increase the braking torque.

NB: Turn both springs through the same amount.

-- 6 8 --

fhb7i1ea

3.4 Connections

3.4.1 General

S TheA2--A6ProcessController(PEH) is to be connected by a qualified person.

S The A2 Welding Control Unit (PEI) is to be connected by a qualified person.

S For the connection of welding power source LAF/ TAF, see separate instruction

manual.

3.4.2 Automatic welding machine A2 TF ( Sub merged arc welding , SAW)

1. Connect the control cable (7) between the power source (8) and the control box

A2--A6 Process Controller/ A2 Welding Control Unit (2).

2. Connect the return cable (11) between the power source (8) and work piece (9).

3. Connect the welding cable (10) between the power source (8) and the automatic

welding machine (1).

4. Connect the measurement cable ( 12) between the power source (8) and

workpiece ( 9 ).

-- 6 9 --

fhb7o1ea

4 OPERATION

4.1 General

Caution:

Have you read and understood the safety information ?

You must not operate the machine before then !

General safety regulations for the handling of the equipment can be found on

page 62. Read through before you start using the equipment!

S Select electrode type and flux powder or shielding gas so that the weld material

is as close as possible to the analysis of the base metal.

S Select electrode size and welding data in accordance with the values

recommended by the welding materials supplier.

S Thorough preparation of the weld surfaces is necessary to achieve a good weld.

NOTE! The width of the weld joint gap must be uniform.

S To minimise the risk of heat crack formation, the width of the weld must be

greater than the penetration depth.

S Always carry out a test weld with the same joint type and sheet thickness as the

production work piece.

S For control and adjustment of the automatic welding m achine and welding power

supply, see the instruction manual for the A2--A6 Process Controller (PEH)orthe

instruction manual for the A2 Welding Control Unit (PEI).

-- 7 0 --

fhb7o1ea

4.2 Loading the welding wire

1. Mount the wire drum according to the

instructions on page 67.

2. Check that feed roller (1) and contact jaw or

contact tip (3) are of the correct dimension for

the selected wire size.

3. Pull the end of the wire through the straightener ( 2).

S For a wire diameter greater than 2 mm;

straighten out 0.5 m of wire and feed it by

hand down through the straightener.

4. Locate the end of the wire in the feed roller (1 ) groove.

5. Set the wire tension on the feed roller with the knob ( 4 ).

S Note! Do not tension m ore than is required to

achieve an even feed.

6. Feed the wire forward 30 mm by pressing either on the control box

A2--A6 Process Controller (PEH)or

by using on the control box A2 Welding Control Unit (PEI).

7. Direct the wire by adjusting the knob ( 5 ).

4.3 Changing the feed roller

Single wire

S Release the knobs (3) and (4).

S Release the hand wheel (2).

S Change the feed roller (1).

They are marked with their respective wire sizes.

Flux--cored wire f o r knurled rollers (Accessories)

S Change the feed roller (1) and pressure roller (5) as a pair for the wire size to be

used.

NOTE! A special stub shaft is required for the pressure roller

(order no. 0212 901 101).

S Tighten the pressure screw (4) with moderate pressure to ensure that the

flux--cored wire does not deform.

-- 7 1 --

fhb7o1ea

4.4 Contact equipment

For single wire 1.6 -- 4.0 mm. Light duty (D20)

The following are included:

S Wire feed unit (1),

S Connector D20 (2)

S Contact tip (3) (M12 thread).

Tighten the contact tip ( 3 ) with a key in order to

ensure that a good contact is achieved.

4.5 Refilling with flux powder

1. Close the flux valve (1) on the flux hopper.

2. Remove the cyclone on the flux recovery unit, if fitted.

3. Fill with flux powder.

NOTE! The flux powder must be dry. Where possible

avoid using agglomerating flux powder outdoors and

in damp environments.

4. Position the flux tube so that it does not become

kinked.

5. Adjust the height of the flux nozzle above the weld so

that the correct amount of flux is delivered.

Flux coverage should be sufficient so that penetration

of the arc does not occur.

4.6 Placing the Control Unit PEH

In order to reduce the risk of overturning, the control unit PEH is to be fitted as far

back as possible.

-- 7 2 --

fhb7o1ea

4.7 Transportation of the Automatic Welding Machine

S Disengage the wheels by turning the locking lever (1 ).

S Make sure the safety chain (2) is properly

fastened; this to prevent an accident happening,

if for example the carrier is not adequately

locked to the foot clamp of the carriage.

For transportation through a m anhole

the chain can be removed.

N.B. In case of lifting the automatic welding machine, the hole (3)istobeused.

-- 7 3 --

fhb7m1ea

5 MAINTENANCE

5.1 General

Note:

All warranty undertakings given by the supplier cease to apply if the customer

attempts to rectify any faults on the m achine during the warranty period.

NB! Before doing any kind of maintenance work, make sure the m ains is

disconnected.

For the maintenance of the A2--A6 Process Controller ( PEH), see the instruction

manual 0443 745 xxx.

For the maintenance of the A2 Welding Control Unit ( PEI), see the instruction

manual 0449 331 xxx.

5.2 Daily

S Clean flux and dirt off moving parts of the welding machine.

S Check that the contact tip and all electrical cables are connected.

S Check that all bolted joints are tight and that guides and drive rollers are not

worn or damaged.

S Check the brake hub braking torque. It should not be so low, that the wire reel

continues to rotate when wire feed is stopped and it should not be so great that

the feed rollers slip. As a guide, the braking torque for a 30 kg wire reel should

be 1,5 Nm.

To adjust the braking torque see on page 67.

5.3 Periodic

S Inspect the electrode feed unit’s electrode control, drive r ollers and contact tip.

S Replace worn or damaged components.

S Inspect the slides, lubricate them if they are binding.

-- 7 4 --

fhb7f1ea

6 TROUBLESHOOTING

6.1 General

Equipment

S Instruction manual control box A2--A6 Process Controller (PEH).

S Instruction manual control box A2 Welding Control Unit (PEI).

Check

S that the power supply is connected for the correct mains supply

S that all three phases are supplying the correct voltage (phase sequence is not

important)

S that welding cables and connections are not damaged

S that the controls are correctly set

that the mains supply is disconnected before starting repairs

6.2 Possible faults

1. Symptom Current and voltage readings show large fluctuations.

Cause 1.1 Contact jaws or nozzle are worn or wrong size.

Action Replace contact jaws or nozzle.

Cause 1.2 Feed roller pressure is inadequate.

Action Increase pressure on feed rollers.

2. Symptom Wire feed is irregular.

Cause 2.1 Pressure on feed rollers incorrectly set.

Action Adjust pressure on feed rollers.

Cause 2.2 Feed rollers wrong size.

Action Replace feed rollers.

Cause 2.3 Grooves in feed rollers are worn.

Action Replace feed rollers.

3. Symptom Welding cables overheating .

Cause 3.1 Poor electrical connection.

Action Clean and tighten all electrical connections.

Cause 3.2 Cross--sectional area of welding cables too small.

Action Use cables with a larger cross--section or use parallel cables.

7 ORDERING OF SPARE PARTS

Spare parts are order ed through your nearest ESAB representative, see back cover.

When ordering spare parts, p lease state machine type and number as well as desig -

nation and spare part number as shown in the spare parts list on page 175.

This will simplify dispatch and ensur e you get the right part.

ESAB AB

SE--695 81 LAXÅ

SWEDEN

Phone +46 584 81 000

www.esab.co m

041227

ESAB subsidiaries and representative offices

Europe

AUSTRIA

ESAB Ges.m.b.H

Vienna--Liesing

Tel: +43 1 888 25 11

Fax: +43 1 888 25 11 85

BELGIUM

S.A. ESAB N.V.

Brussels

Tel: +32 2 745 11 00

Fax: +32 2 745 11 28

THE CZECH REPUBLIC

ESAB V AMBERK s.r .o.

Prague

Tel: +420 2 819 40 885

Fax: +420 2 819 40 120

DENMARK

Aktieselskabet ESAB

Copenhagen--Valby

Tel:+4536300111

Fax:+4536304003

FINLAND

ESAB Oy

Helsinki

Tel: +358 9 547 761

Fax: +358 9 547 77 71

FRANCE

ESAB France S.A.

Cergy Pontoise

Tel:+33130755500

Fax:+33130755524

GERMANY

ESAB GmbH

Solingen

Tel: +49 212 298 0

Fax: +49 212 298 218

GREAT BRITAIN

ESAB Group (UK) Ltd

Waltham Cross

Tel: +44 1992 76 85 15

Fax: +44 1992 71 58 03

ESAB Automation Ltd

Andover

Tel: +44 1264 33 22 33

Fax: +44 1264 33 20 74

HUNGARY

ESAB Kft

Budapest

Tel:+3612044182

Fax:+3612044186

ITALY

ESAB Saldatura S.p.A.

Mesero (Mi)

Tel:+3902979681

Fax:+390297289181

THE NETHERLANDS

ESAB Nederland B.V.

Utrecht

Tel: +31 30 2485 377

Fax: +31 30 2485 260

NORWAY

AS ESAB

Larvik

Tel:+4733121000

Fax:+4733115203

POLAND

ESAB Sp.zo.o.

Katowice

Tel: +48 32 351 11 00

Fax: +48 32 351 11 20

PORTUGAL

ESAB Lda

Lisbon

Tel: +351 8 310 960

Fax: +351 1 859 1277

SLOVAKIA

ESAB Slovakia s.r.o.

Bratislava

Tel:+421744882426

Fax:+421744888741

SPAIN

ESAB Ibérica S.A.

Alcalá de Henares (MADRID)

Tel: +34 91 878 3600

Fax: +34 91 802 3461

SWEDEN

ESAB Sverige AB

Gothenburg

Tel:+4631509500

Fax:+4631509222

ESAB International AB

Gothenburg

Tel:+4631509000

Fax:+4631509360

SWITZERLAND

ESAB AG

Dietikon

Tel: +41 1 741 25 25

Fax: +41 1 740 30 55

North and South America

ARGENTINA

CONARCO

Buenos Aires

Tel: +54 11 4 753 4039

Fax: +54 11 4 753 6313

BRAZIL

ESAB S.A.

Contagem--MG

Tel: +55 31 2191 4333

Fax: +55 31 2191 4440

CANADA

ESAB Group Canada Inc.

Missisauga, Ontario

Tel: +1 905 670 02 20

Fax: +1 905 670 48 79

MEXICO

ESAB Mexico S.A.

Monterrey

Tel: +52 8 350 5959

Fax: +52 8 350 7554

USA

ESAB Welding & Cutting Products

Florence, SC

Tel: +1 843 669 44 11

Fax: +1 843 664 57 48

Asia/Pacific

CHINA

Shanghai ESAB A/P

Shanghai

Tel: +86 21 5308 9922

Fax: +86 21 6566 6622

INDIA

ESAB India Ltd

Calcutta

Tel: +91 33 478 45 17

Fax: +91 33 468 18 80

INDONESIA

P.T. ESABindo Pratama

Jakarta

Tel: +62 21 460 0188

Fax: +62 21 461 2929

JAPAN

ESAB Japan

Tokyo

Tel: +81 3 5296 7371

Fax: +81 3 5296 8080

MALAYSIA

ESAB (Malaysia) Snd Bhd

Shah Alam Selangor

Tel: +60 3 5511 3615

Fax: +60 3 5512 3552

SINGAPORE

ESAB Asia/Pacific Pte Ltd

Singapore

Tel: +65 6861 43 22

Fax: +65 6861 31 95

SOUTH KOREA

ESAB SeAH Corporation

Kyungnam

Tel: +82 55 269 8170

Fax: +82 55 289 8864

UNITED ARAB EMIRATES

ESAB Middle East FZE

Dubai

Tel: +971 4 887 21 11

Fax: +971 4 887 22 63

Representative offices

BULGARIA

ESAB Representative Office

Sofia

Tel/Fax: +359 2 974 42 88

EGYPT

ESAB Egypt

Dokki--Cairo

Tel: +20 2 390 96 69

Fax: +20 2 393 32 13

ROMANIA

ESAB Representative Office

Bucharest

Tel/Fax: +40 1 322 36 74

RUSSIA--CIS

ESAB Representative Office

Moscow

Tel:+70959379820

Fax: +7 095 937 95 80

ESAB Representative Office

St Petersburg

Tel:+78123254362

Fax: +7 812 325 66 85

Distributors

For addresses and phone

numbers to our distributors in

other countries, please visit our

home page

www.esab.co m

ESAB A2 Tripletrac User manual

Brand: ESAB

Model: A2 Tripletrac

Category: Welding System

Type: User manual

Download PDF

report

ESAB A2 Tripletrac User manual

ESAB A2 Tripletrac User manual

Related papers

Other documents