Craftsman 315111810 Owner's manual
- Category
- Power screwdrivers
- Type
- Owner's manual
This manual is also suitable for
Owner's Manual !
CRRFTSMRN°
Single Speed / Reversible
CORDLESS SCREWDRIVER
Model No.
315.111810
Save this manualfor
future reference
CAUTION: Read and
follow all Safety Rules anlLIBRARY:.
Operating Instructions
before first use of this
product.
Sears, Roebuck and Co., I-LO_llan Estates, I_._S,_'
972000-446
9-97
• Table Of Contents ................................................................................................................................ _._.._....2
• Warranty ......................................................................................................................................................... 2
• Introductionand ProductSpecifications......................................................................................................... 2
• RulesFor Safe Operation ........................................................................................................................... 3-5
A. ImportantSafety Rules For BatteryTools .............................................................................................. 4
B. ImportantSafety InstructionsFor Charger .......................................................................................... 4-5
• Accessodes.................................................................................................................................................... 5
• Features ......................................................................................................................................................... 6
• Operation..................................................................................................................................................... 7-9
• Maintenance................................................................................................................................................. 10
• BatteryRemoval ........................................................................................................................................... 11
A. BatteryRemoval, Preparation For Recycling....................................................................................... 11
• Replacement Parts ................................................................................. .:.................................................... 11
• Parts Ordering/ Service............................................................................................................................... 12
FULL ONE YEAR WARRANTY ON CRAFTSMAN CORDLESS SCREWDRIVER
If this CRAFTSNAN Cordless Screwdriverfails togive complete satisfactionwithinone year fromthe date of
purchase, RETURN IT TO THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears willreplace it,
free of charge.
If this rRAFlrSNRN Cordless ScrewdriveriSused forcommemialor rental purposes,this warrantyappliesfor
only90 days fromthe date ofpurchase,
Thiswarranty gives you specificlegal rights,and you may also have otherrightswhichvary fromstate tostate.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Yourscrewdriverhas many features formaking
driving operationsmore pleasant and enjoyable.
Safety, performanceand dependabilityhave been
given toppriorityinthe designofthis screwdriver
makingit easy to maintainand operate.
CAUTION: Carefully read throughthis entire
owner's manual beforeusingyour new
screwdriver.Pay closeattentiontothe Rules For
Safe Operation, Warningsand Cautions. Ifyou
useyour screwdriver properlyand onlyforwhat it
isintended,you will enjoyyears of safe, reliable
SPECIFICATIONS:
Collet 1/4 in.
Motor 2.4 Volts DC
Charger Rating 120 Volts,60 Hz, AC Only
No Load Speed 165 RPM
Switch Single Speed - Reversible
Charge Rate 3-5 Hours
tl_._;_J 20 in. Lbs.
,_-Look for this symbol to point out important safely Precautions. It means attention!!! Your
_Pf_e]yJsjnvolved ....
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and
the explanations wlth them, deserve your careful attention and understanding, The safety wamlngs do _
not by themselves ellmlnate any danger. The Instructions or warnings they give are not substltutes for
proper accident prevention measures.
SYMBOL MEANING
A
SAFETY ALERT SYMBOL:
Indicatescautionorwarning.Maybeusedinconjunctionwithothersymbolsorpictographs.
g
A
WARNING: Failureto obey asafety warningcan resultin seriousinjuryto yourselforto others.
Alwaysfollowthe safety precautionsto reduce the dskof fire,electricshockand personalinjury.
A
CAUTION: Failureto obeya safetywarningmay resultinpropertydamage or personalinjuryto
yourselfor toothers.Alwaysfollow thesafety precautionstoreduce_thedskoffire, electdcshock
and personalinjury.
NOTE: Advisesyou of informationor instructionsvital tothe operationor maintenanceof the equipment._-" *-
_k WARNING: Do not attemptto operatethis tool •
untilyou have read thoroughlyand understand
completelyall instructions,safety rules, etc.
containedin this manual. Failure to comply can
resultin accidents involvingfire, electricshock,
or sedous personalinjury.Save owner'smanual •
and reviewfrequently for continuingsafe
operation,and instructingotherswho may use
this tool.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read owner's
manual carefully. Learn its applications and
limitations as well as the specific potential
hazards related to this tool.
GUARD AGAINST ELECTRICAL SHOCK by
preventingbody contactwithgroundedsurfaces.
Forexample: Pipes, radiators,ranges, refrigera-
tor enclosures.
• KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents.
AVOID DANGEROUS ENVIRONMENT. Don't
use power toolin damp orwet locationsor
expose to rain. Keep workarea well lit.
KEEP CHILDREN AND VISITORS AWAY. All
visitorsshouldwear safety glassesand be kept a
safe distancefromwork area. Do not let visitors
contacttoolor extension cord.
STORE IDLE TOOLS. When not in use tools
should be stored in a dry and highor locked-up
place- out of the reach of children.
DON'T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
USE RIGHT TOOL Don'tforce smalltoolor
attachmentto do the job of a heavy dutytool.
Don't usa toolfor purposenot intended - for
example - A circularsaw should never be used
for cuttingtree limbsor logs.
WEAR PROPER APPAREL. Do not wear loose
clothingor jewelrythat can get caught intool's
movingparts and cause personal injury.Rubber
glovesand nonskidfootwear are recommended
whenworkingoutdoors.Wear protectivehair
coveringtocontainlong hairand keep it from
being drawnintonearby air vents.
ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses;
they are NOT safety glasses,
PROTECT YOUR LUNGS. Wear a face mask or
dust maskifoperation isdusty.
PROTECT YOUR HEARING. Wear headng
protectionduringextended periodsof operation.
SECURE WORK. Use clampsor a viseto hold
work. It'ssafer than usingyour hand and it frees
both hands tooperate tool.
DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable supped.
MAINTAIN TOOLS WITH CARE. Keep tools
sharp at all times, and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories.
REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from
tool before turning it on
3
RULESFORSAFEOPERATION(Continued)
NEVER USE IN AN EXPLOSIVE ATMO-
SPHERE. Normal sparking of the motor could
ignite flammable liquids, gases, or fumes.
KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Alwaysuse a clean
cloth whencleaning. Never use brake fluids,
gasoline,petroleum-based productsor any
strongsolventsto clean your tool
STAY ALERT. Watch what you are doing and
use common sense. Do not operate tool when
you are tired. Do not rush.
CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Chock for alignment of moving pads,
binding of moving pads, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced by an authorized service center unless
indicated elsewhere in this instruction manual.
DO NOT USE TOOL IF SWITCH DOI_S NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
DRIVING SCREWS INTO ELECTRICAL
WIRING IN WALLS, CEILINGS, OR OTHER
AREAS CAN CAUSE THE SCREWDRIVER BIT
OR COLLET TO BECOME ELECTRICALLY
LIVE. Do not touch metal parts when driving
screws into a wall; grasp only the insulated
handle(s) or plastic housing when using this tool.
Make sure hidden electrical wiring, water pipes,
and mechanical hazards are not in the path of
the bit when driving screws into a wall.
• INSPECT FOR and remove all nails from lumber
before driving screws.
IMPORTANT SAFETY RULES FOR BATTERY
TOOLS
Battery toolsdo not have to be plugged intoan
electricaloutlet; therefore, theyare always in
operatingcondition.Be aware of possible
hazards when not using yourbatterytoolor
when changing accessories.
USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. Do notsubstituteany
other charger. Use of another chargercould
cause batteries toexplode causing possible
serious injury.
DO NOT PLACE BATTERY TOOLS OR THEIR
BATTERIES NEAR FIRE OR HEAT. Theymay
explode.
DO NOT CHARGE BA'FrERY TOOL IN A
DAMP OR WET LOCATION.
Your batterytoolshould be charged in a location
where the temperature is morethan 50°F but
lessthan 100°F.
Under extreme usage or temperature conditions,
batteryleakage may occur. If liquidcomes in
contactwith your skin, wash immediatelywith
soap and water, then neutralize withlemonjuice
or vinegar. If liquidgets in youreyes, flush them
with cleanwater for at least 10 minutes,then
seek immediate medicalattention.
if carryingyour batterytool at yourside, make
sure itis not runningand your finger isnot__on the
switch.Avoid accidentalstarting.
SECURE WORK before applyingpower, NEVER
hold workpiecein yourhand or acrossyour legs.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS,
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER
• SAVE THESE INSTRUCTIONS. This manual
contains importantsafety and operating
instructionsforbatterycharger part number
999555-001.
Before usingbattery charger, read allinstructions
and cautionarymarkings in this manual, on
battery charger, and product using battery
charger,
_k WARNING: To reduce riskof injury,charge only
nickel-cadmiumtype rechargeable batteries.
Other types ofbatteries may burstcausing
personal injuryand damage.
m
Do not expose charger to rain or snow.
Use of an attachment notrecommended orsold
by the batterycharger manufacturermay result
in a riskoffire, electricshock, or injuryto
persons.
To reduce risk ofdamage to charger body and
cord, pullby charger bodyrather than cordwhen
disconnectingcharger.
Make sure cordislocated sothat it willnet be
stepped on, tripped over, or otherwisesubjected
to damage or stress.
RULESFORSAFEOPERATION(Continued)
Anextensioncordshouldnotbeusedunless
absolutelynecessary,Useofimproper
extensioncordcouldresultinariskoffireand
electricshock.Ifextensioncord must be used,
make sure:
a. That pinson plug ofextensioncord are the
same number, size and shape as those of
plugon charger.
b. That extensioncord isproperlywired and in
good eiactdcalcondition; and
c. That wire size is largeenough for AC
ampere ratingofcharger as specified
below:
Cord Length(Feet) 25ft. 5Oft. 100ft. 150ft.
Cord Size (AWG) 16 16 16 14
Note: AWG = American Wire Gage
• DO NOT OPERATE CHARGER WITH A
DAMAGED CORD OR PLUG. Ifdamaged, have
replacedimmediatelybyaqualifiedserviceman.
Do not operate charger ifit has receiveda
sharp blow,been dropped, or othen,#ise
damaged in any way;take it toa qualified
serviceman.
Do not disassemblecharger;take itto a
qualifiedserviceman when service or repairis
required, Incorrectreassemblymay resultin a
dskof electricshockor fire.
To reduce risk ofelectdcshock, unplugcharger
from outletbeforeattempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
• Do not use charger outdoors.
• Disconnectcharger frompower supplywhen
notin use.
SAVE THESE INSTRUCTIONS. Referto them
frequentlyand use-them toinstructotherswho
may use thistool, If you loan someonethis tool,
loanthem these instructionsalso,
_1= WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage, Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and a full face shield when needed, We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses
with side shields, avaiEable at Sears Retail Stores.
,_ WARNING: Do not allow familiarity with your
screwdriver to make you careless, Remember
that a careless fraction of a second is sufficient to
inflict severe injury.
,_ CAUTION: Your screwdrivercontainsspecial
hightemperature batteriesto help prevent
batterydamage when lefton charge for extended
periodsof time. However,once the batteries
become fullycharged, we recommendthat you
unplugyourcharger from powersupplyand
disconnectitfrom scrswddver.
The fo ow ng recommended accessories are_urrently available at Sears Retail Stores.
No, 2 Phillips/ 8-10 Slotted,2 Ea.
No. 3 Phillips/ 6-8 Slotted, 2 Ea.
5-Pc. Hex Shank Drill BitSet
6-Pc. Extra LengthScrewdriverBitSet
"/-Pc. ScrewdriverBitSet and Case
13-Pc. Power Screwdriver/ NutdriverSet and
Case
30-Pc. Power Scrawddver/Nutdriver Set and
Case
17-Pc, Power Screwdriver/Nutdriver Set and
Case
_. WARNING: The useofattachmentsor accessories not listedmightbe hazardous,
KNOW YOUR SCREWDRIVER
See Figure 1.
Before attemptingto use your screwdriver,familiadze
yourselfwithall operatingfeatures and safety
requirements.
WARNING: If any partsare missing,do_01"
operate tooluntilthe missingpartsare replaced.
Failure to do so could resultin possibleserious
personal injury.
REVERSE
_EWOFSCREWDRIVERIN OPERA_NGPosmoN
FORWARD(_
REVERSE_)SWITCH
FORWARD
CENTER
POSITION_OCK)
ADJUSTMENT CAP
WRISTSTRAP
VIEW OF SCREWDRIVER IN UPSIDE DOWN POSITION
SWITCHTRIGGER
LIGHTSWITCH
UGHT
ENDCAP
WlTHEXTRA
BULBSTORAGE
LIGHT
As shownin figure 1, your screwdriverhas been
designedwith a light. Thisfeature is convenientwhen
workingin closeor tight areas where additionallightis
needed.
Fig. 1
WRIST STRAP
See Figure 1.
A wriststrapisprovidedto reduce the chancesof
droppingyour screwdriver.Place one hand through
the wriststrap when carryingtool,
CHARGING YOUR SCREWDRIVER
Your screwdriver has been shipped in a low charge
condition to prevent possible problems. Therefore,
you should charge it at least 3 hours prior to use.
Note: Batteries will not reach ful! charge the first time
they are charged. Allow several cycles (driving
screws followed by recharging) for them to become
fully charged.
If the charger does not charge your screwdriver under
normal circumstances, return both the screwdriver
and charger to your nearest Sears repair center for
electrical check.
CHARGING STAND
See Figure2.
CHARGING
PILOTHOLES
.s
SCREWS
WALL
ANCHORS
BIT
CHARGE
UGHT(LED)
BR
STORAGE
AREA
CHARGER
BO'I'rOMOF
CHARGING STAND INPUT
CHARGERPLUG
Fig. 2
For storage convenience,a chargingstand withbit
storage has been providedwith your screwdriver.It
has the capacityof storingyour screwdriverand two
(2) bitswhichare also includedwith yourscrewdriver.
TO MOUNT CHARGING STAND
See Figures2 and 3.
2-3/8 in.
BACK SIDE OFCHARGINGSTAND Fig. 3
• Locate close to an electrical outlet.
Note: Temporarily place your screwdriver in
charging stand. Check to make sure it will not
interfere with the charger or electrical outlet.
• Drill two (2) pilot holes then insert the two (2)
wall anchors provided.
Note: Pilot holes should be 2-3/8 inches apart.
See Figure 3.
• Position charging stand on wall aligning holes in
charging stand with pilot holes.
• Secure charging stand with the two (2) screws
provided.
TO CHARGE
• Place the forward/reverse switchin center
position.
• Place screwdriverin chargingstand.
Note: Screwdrivermust be inchargingstand tobe
charged.
• Insertcharger plugintoinputjack making sure
theyare propertyconnected.
• Charger can be used with normal house
voltage of 120 volts, 60 Hz, AC only.
• Connectcharger to powersupply.
• The charge indicatorlight(LED) indicator,whichis
locatedon the chargingstand, willlightupwhen
charger ispropedyconnected topower supply.
This red lightindicatesyour screwdriverischarg-
ingand willremain on untilcharger is discon-
nectedfrom power supply.
• Afternormalusage, a minimumof3 hours of
chargingtime isrequiredto be fully charged.
• DO NOT place charger in an area ofextreme heat
orcold. It worksbest at normalroomtemperature.
SWITCH
See Figure 4,
To turnyour screwdriverON, depressswitchtriggerin
the directionofthe arrow infigure 4. To turn itOFF,
releasethe switchtdgger.
REVERSIBLE
See Figure5.
Fig. 4
REVERSE(R) FORWARD(_
FORWARD(_
CENTER REVERSE(R)
PosmoN SWITCH
(LOC_
Your screwdriverisequippedwith a Forward/litllmrse
Switchwhichallows you tochange the directionof
rotationof the bit. For ddvingor forwardrotation,slide
the switchto the forward(F) position.To reversethe
bitdirection,slide the switchtothe reverse(R)
position.
CAUTION: To preventgear damage, always
allow bitto come toa complete stopbefore
changingthe directionof bit mtation.
To stop yourscrewdriver,release switchtdggerand
allow yourscrewdrivertocome toa complete stop.
SWITCH LOCK
See Figure 5.
The switchtrigger can be lockedin the OFF position.
This feature can be usedto preventthe pessi_"ity of
accidental startingwhen not in use. To lockswitch
tdgger, place the forward/reverse switchin center
position.
_ WARNING: Batterytoolsare always in
operatingcondition. Therefore, switchshould
always be locked when not in usaor carrying at
your side.
_ WARNING: Always wear safety goggles or
safety glasses with side shields when operating
tools. Failure to do so could result in objects
being thrown into your eyes, resulting in possible
serious injury.
Fig. 5
COLLET
Thecolletonyourscrewdriverhasbeendesignedto
accept1/4in,hoxbits.See Figure 6,
COLLET
\
Fig. 6
TO INSERT BIT
See Figure 6.
• Lockswitchtdgger byplacingthe forward/reverse
switchin center position.See Figure 5.
• Insert bitintocolletas far as possible,
• When finishedusingyour screwdriver,remove bit
fromcolletand place it in chargingstandfor
storage. See Figure2.
I
I
BITSINCLUDED WITHCORDLESS SCREWDRIVER I
I
Double-ended Bit(#1 Phillipsand #5 Slotted)
Double-ended Bit (#2 Phillipsand #7 Slotted)
ADJUSTABLE TORQUE CLUTCH
(Tightening Power of Your Screwdriver)
See Figure
TO
INCREASETOROUE
J TORQUE
ADJUSTMENT
CAP
TO
DECREASETORQUE Fig. 7
When usingyour screwdriverfor various driving
applications,it becomes necessaryto increaseor
decrease the power and torquein orderto help
preventthe possibilityofdamaging screwheads,
threads, workpiece, etc. In general, power and torque
shouldcorrespondto the difficultyof the screwto be
ddven. If torqueis too highthe screws may be
damaged or broken.
Note: Your screwdriver has been shippedwiththe
adjustabletorqueclutchset at the lowest torque
setting.
TO ADJUST TORQUE
See Figure 7.
• Locatearrow ontorque adjustmentcap.
• To increase torque, rotate torqueadjustmentcap
inthe directionof the arrow, When cap stops
rotating,you have reached the highesttorque-
setting.To decrease torque, rotatetorque adjust-
ment cap in the oppositedirectionofthe arrow.
When cap stops rotating,you have reached the
lowesttorquesetting.
BATrERIES
Your scrowddverisequippedwith 2 nickel-cadmium
rechargeable batteries.Lengthof servicefrom each
chargingwill depend on the type ofworkyou are
doing.
The batteries in thistoolhave been designed to
providemaximum troublefree life, However, like all
batteries,they willeventuallywear out.To remove
batteries,see page 11, BatteryRemoval. Handling of
these batteries,especially whenwearing dngsand
jewelry, could resultin a serious burn,
To obtain the longestpossiblebatterylife, we suggest
the following:
• Store and charge yourbatteries in a cool area.
Temperatures above normalroomtemperature
willshorten batterylife.
• Never storebatteries in a dischargedcondition.
Rechargethem immediately after theyare dis-
charged.
• All batteriesgradually losetheir charge. The
higherthe temperature,the quickerthey losetheir
charge. If you storeyour toolfor longperiodsof
timewithout usingit, rechargethe batteriesevery
monthor two. Thispracticewillprolongbattery
life.
_, WARNING: When servicing,use only identical
Craftsman replacement parts. Use ofany other
part may create a hazard or cause product
damage.
,_ WARNING: Donot at any time let brakefluids,
gasoline, petroleum-based products,penetrating
oils, etc. come in contactwithplastic parts.They
containchemicalsthat can damage, weaken or
destroy plastic.
Only the partsshown on parts list,page 11, are
intended to be repaired or replaced bythe customer•
All other partsshouldbe replaced by a qualified
servicetechnician at an authorized servicefacility.
Avoid usingsolvents when cleaning plasticparts.
Most plasticsare susceptibleto damage from various
types ofcommercial solvents and may be damaged
by their use. Use clean clothsto remove dirt,dust, oil,
grease, etc.
DO NOT ABUSE POWER TOOLS. Abusivepractices
can damage toolas well as workpiece.
_k WARNING: Do not attempt to modifythis toolor
create accessoriesnot recommendedfor use
with thistool•Any suchalterationor modification
is misuseand couldresultin a hazardous
conditionleadingto possibleserious personal
injury.
BULB REPLACEMENT
See Figures 8 and 9.
• Loci< switch trigger by placing the forward/reverse
switch in center position.
• Remove bulb cover.
Note: Depress bulb cover and slide forward as
shown by the arrows in figure 8 to remove.
SUDEFORWARD DEPRESSHERE
BULB
COVER
Remove old bulb by liftingit from socket.
Foryour convemence,a bulb storagearea withan
extra bulbhas been provided.It is locatedinside
the end cap on the bottomofyour screwdriver.
See Figure 9.
BULB
STORAGE
AREA
TOREMOVE
ENDCAP
MOTOR
HOUSING
EXTRA END
BULB CAP
TOREPLACE
ENDCAP Fig. 9
• Remove end cap by twistingit inthe directionof
the arrow as shownin figure 9.
• Positionnew bulb insocket.
• Replace bulbcover by insertingtab intoslot.
• Replace end cap.
BULB
\
SOCKET
Fig. 8
10
To preservenaturalresources,please
recycleor disposeofexpiredbatteries
This productcontains nickel-cadmium
battery. Mustbe disposedof properly.
Local,state, or federal laws may prohibitdisposalof
nickel-cadmiumbatteries in ordinarytrash.
Consultyour localwaste authorityfor information
regardingavailable recyclingand/or disposaloptions.
BATTERY REMOVAL, PREPARATION FOR
RECYCLING
SeeRgurel_
TO REMOVE:
• Lock switchtdgger by placingthe forward/reverse
switchin center position.See Figure 5.
• Remove end cap securing batteriesby twistingit
in the directionof the arrow as shownin figure 10.
• Slide batteriesfrom motorhousingenoughto
exposeleads and batteryterminals. Disconnect
leadsfrombattery terminals.Note where each
lead connectstobattery terminals.Connection
must beidenticalwhen installingnew batteries.
Note: Be careful notto break batteryterminals
when disconnectingleads.
_k WARNING: Upon removal, cover the battery's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of
properly. Also, never touch both terminals with
metal objects and/or body parts as short circuit
may result, Keep away from children. Failure to
comply with these warnings coutd result in fire
and/or serious injury,
TERMINAL
MOTOR
HOU_NG
TOREMOVE
ENDCAP
TO REPLACE
ENDCAP ENDCAP
BAKERY
LEADS
BATTERIES
BA'I'rERY
TERMINAL
Fig. 10 H
WHEN SERVICING, USE ONLY IDENTICAL CRAFTSMAN REPLACEMENT PARTS
Key Part
No. Number Description
1 974277-003 BatteryPack .
2 999555-001 Battery Charger
3 974385-002 Charging Stand
972000-446 Owner's Manual
11
Forthe repairor replacementpartsyouneed
delivereddirectlyto yourhome
Call7 am- 7 pm,7 daysaweek
1-800-366-PART
(1-800-366-7278)
Forrepairservice
Call24 hoursa day,7 daysaweek
1-800-4-REPAIR
(1-800-473-7247)
Forthe locationof a
SearsPartsandRepairCenterinyourarea
Call24 hoursaday,7daysaweek
1-800-488-1 222
imiii|
Themodelnumberofthistoolwill befoundonaserialplate
attachedtothemotorhousing.Whenrequestingserviceor
order!ngparts,alwaysprovidethefollowinginformation:
• ProductName
Cordless
Screwdriver
• Model Number
315.111810
SEARS
• PartName • PartNumber America'sRepairSpecia/ists
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Craftsman 315111810 Owner's manual
- Category
- Power screwdrivers
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Craftsman 973.112090 Owner's manual
-
-
-
-
-
-
-
-
Sears COMPANION 27812 User manual
-