GE 2661532110 Installation guide

Category
Electric laundry dryers
Type
Installation guide
Installation
Instructions
Unitized Electric
Washer/Dryer
Questions on installation? Call: 1-800-GECARES {US} or Visit our Web site at: www.GEAppliances.com (US).
In Canada, call 800.561.3344 or visit www.GEAppliances.cu
i
BEFORE YOU BEGIN
Readthese instructions completely and
carefully.
IMPORTANT- savethese instructions for
localinspector's use.
IMPORTANT- Observeall governing codes
and ordinances.
Note to Installer - Be sure to leave these
instructionswith the customer.
Note to Customer- Keepthese instructionswith
your Owner's Hanual for future reference.
Beforethe appliance is removedfrom serviceor
discarded,remove thewasher and dryer doors.
Inspect the dryer exhaust outlet and straighten
the outlet walls ifthey are bent.
Service information and the wiring diagram are
located at the accesspanel.
Do not allow children on or in the appliance.
Closesupervision of children isnecessarywhen
the appliance isusednear children.
Install the appliance where the temperature is
above 50°F for satisfactory operation of the
control system.
Productfailure due to improper installation isnot
coveredunder the Warranty.
_LW_KI_I|I_I£_" RISK OF FIRE
. To reduce the risk of severe injury or death, follow all installation
instructions.
Appliance installation must be performed by a qualified installer.
Install the appliance according to these instructions and in accordance
with local codes.
This appliance must be exhausted to the outdoors.
Use only 4" rigid metal ducting for exhausting the clothes dryer to the
outdoors.
DO NOT install a clothes dryer with flexible plastic ducting materials.
If flexible metal (semi-rigid or foil-type) duct is installed, it must be
UL listed and installed in accordance with the instructions found
in "Connecting The Dryer To House Vent" on page 8 of this manual.
Flexible venting materials are known to collapse, be easily crushed,
and trap lint. These conditions will obstruct dryer airflow and increase
the risk of fire.
Do not install or store this appliance in any location where it could be
exposed to water and or weather.
Save these instructions. (Installers: Be sure to leave these instructions
with the customer).
NOTE: installation and service of this appliance requires basic
mechanical and electrical skills, it is your responsibility to
contact a qualified installer to make the electrical connections.
TOOLS YOU WILL NEED
Slip Pliers
Phillips Screwdriver
Flat-blade Screwdriver
1/4" Nutdriver
Level
#' DFA.METALDUCT
(RECOMMENDED/
MATERIALS YOU WILL NEED
#' DUCT
#' DFAFLEXBLEMETAL(SEMFREGED} CLAMPS(2}
ULLISTEDTRANSITIONDUCT
(IFNEEDED} OR
P
KITWXO8XlO077(INCLUDES2 ELBOWS} #' SPRING
CLAMPS(2}
%
#' DIA.METAL
ELBOW
%
EXHAUST SAFETY
HOOD GLASSES
#' DFA.FLEXBLEMETAL(FOELTYPE} _ 3/#'STRAEN
ULLISTEDTRANSITIONDUCT
x,4
(iFNEEDED,} DUCTTAPE GLOVES RELIEF
4"COVERPLATE(iFNEEDED/ ULRECOGNIZED
(KiTWE1M454}
APPLIANCEPOWER
CORDKIT
(NOTPROVIDED/
ULRATED
120/2@V,}OA
WITH3 OR4PRONGS,
IDENTIFYTHEPLUG
TYPEASPERTHE
HOUSERECEPTACLE
BEFOREPURCHASING
LiNECORD,
PARTS SUPPLIED
1 Cable Tie
% oo
2 Rubber Washers 2 Stainer Screens/
Rubber Washers
(washers may be in water hoses)
2 Washer Hoses
Printedin Mexico 233DI835PO02 31-16652-5 12-12 GE
Installation instructions
INSTALLATION REQUIREMENTS LOCATION
This appliance must be installed on firm flooring to minimize
vibration during spin cycle. Concrete flooring is best, but
wood base is sufficient, provided floor support meets FHA
standards. This appliance should not be installed on rugs or
exposed to weather.
PLUMBING
WATERPRESSURE- Must be 20 psi minimum to 120 psi
maximum.
WATERTEMPERATURE- Householdwater heater should be set
to deliverwater at 120°to !50°F (50°to 66°C)INTHEWASHER
when hot wash isselected.
SHUTOFFVALVES- Both hot and cold shutoffvalves (faucets)
should be supplied.
DRAIN- Water may be drained into standpipe or set tub.
Discharge height MUSTNOTBELESSTHAN30 INCHES,and
no more than 8 feet above the baseof the washer. Standpipe
must be 1-1/2 inches minimum insidediameter and must be
open to atmosphere.
ELECTRICAL REQUIREMENTS
CAUTION: Before plugging in washer, read the following
electrical requirements.
CAUTION: For personal safety, do not use an extension
cord or adapter plug with this appliance. Do not, under any
circumstances, cut or remove the third grounding prong
from the power cord. Follow national electrical codes and
ordinances. This appliance must be supplied with the voltage
and frequency indicated on the rating plate (located at the
top of the dryer front panel),and connected to an individual,
properly grounded branch circuit, protected by a 30-amp
circuit breaker or time-delay fuse. If the electric supply
provided doesnot meet the aboverequirements, calla licensed
electrician.
Step ! Prepare the Area and Exhaust for Installation of
Appliance (seesection !).
Step 2 Check and Ensure the Existing External Exhaust is
Clean (seesection !) and Meets Attached Installation
Specifications (seesection 3).
Step 3 Removethe Foam Shipping Pads (seesection !).
Step 4 Hove the Appliance to the Desired Location.
Step 5 Connect the Power Supply (seesection 2).
Step 6 Connect the External Exhaust (seesection 4).
Step 7 LevelYour Appliance (seesection 5).
Step 8 Connect to plumbing facilities (seesection 8).
Step 9 Check the Operation of the Power Supply
and Venting.
Step !0 Place the Owners Manual and the Installation
Instructions in a Location Where They Will Be Noticed Bythe
Owner.
For Alcove or Closet Installation, see section !0.
For Bathroom or Bedroom Installation, see section !!.
For Mobile or Manufactured Home see, section 9.
For side or bottom exhaust, see section 6.
2
7_._c
Installation Instructions
24" NOMINAL PRODUCT DIMENSIONS
51"
!9.1 "J
0ool oo " 0
Water Inlets
(rear) _
,_------*23.75"--------_
--- 43"--------€
* Dimension represents door closed including handle and knobs.
NOTE:With feet set at mid position, feet can be adjusted +_.375".
Gas Inlet
(Rearview of appliance)
27" NOMINAL PRODUCT DIMENSIONS
52.9"
0oolo o , 0
Vent_.Q_..
_._._.. Drain outlet
i (rear)
p3.9"
-_----- 26.8"
4------'26.7"-----_
-- !2.5"
--47"_
Waterlnlets
(rear) 5i_°
36.5"
4.35"
__ m
",_----- 30.85"------_
* Dimension represents door closed including handle and knobs.
NOTE:With feet set at mid position, feet can be adjusted +_575".
Gas Inlet
(Rearview of appliance)
[
Installation Instructions
Minimum Clearance Other Than Alcove or Closet Installation
Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and rear.Consideration must
be given to provide adequate clearance for installation and service.
_-I PREPARING FOR INSTALLATION
OF NEW APPLIANCE
REMOVING LINT FROM WALL EXHAUST
OPENING
Remove and discard existing plastic or metal foil
transition duct and replace with ULlisted transition duct.
WALL
/
INTERNALDUCT
CHECKTHATEXHAUST
OPENING HOODDAMPEROPENS
ANDCLOSESFREELV.
TILTTHE APPLIANCE
SIDEWAYS AND REMOVE
THE FOAM SHIPPING PADS
BY PULLING ATTHE SIDES
AND BREAKING THEM
AWAY FROM THE APPLIANCE
LEGS.BE SURE TO REMOVE
ALL OFTHE FOAM PIECES
AROUND THE LEGS.
After the machine is in the
home, remove remaining
packing material/carton from
washer.
DO NOT REMOVE SHIPPING
RODAT THISTIME.
Remove styrofoam block.
Remove the bag containing
the Washer hoses and parts
parts from tub. Putstyrofoam
block back in tub opening to
hold tub in place during the
rest of installation.
Hove washer close to final
position. Make sure there is
at least a 24" clearance on
right sideof washer to remove
shipping bar. PULLSHIPPING
BAR OUT USING YELLOW
PLASTICHANDLE.Keepbar so
it can be reinstalled if washer
isever moved again.
Styrofoam BlocJ_
Washer hoses
and parts
II
I
Shipping
Bar
Yellow plastic handle
4
NEW HOME OR REMODELING FAUCETS/
DRAI N STANDPIPEIELECTRICAL LOCATION
Right side of
Laundry Center.
.................. _|
Locate spigots, "
drain standpipe ss" |
and electrical plug |
1
in this area
!
FLOOR
[] ELECTRICAL CONNECTION INFORMATION
A WAR N IN G -TOREDUCETHERISKOF
FIRE,ELECTRICALSHOCK AND PERSONAL INJURY:
DO NOT USE AN EXTENSION CORD OR AN
ADAPTER PLUG WITH THIS APPLIANCE.
Thisdryer must be electrically grounded in accordance
with local codes,or inthe absence of localcodes,with the
National ElectricalCode,ANSI/NFPANO.70 or Canadian
ElectricalCode,CSAC22.1.
ELECTRICAL REQUIREMENTS
This appliance must be connected to an individual
branch circuit, protected by the required time-delay
fuses or circuit breakers. A four or three-wire, single
phase, 120/240V or 120/208V, 60Hz, 30 amp circuit
is required. If the electric supply does not meet the
above specifications, then call a licensed electrician.
GROUNDING INSTRUCTIONS
a.
For a grounded, cord-connected appliance:
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of
least resistance of electric current. This appliance is
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
WARNING -Improper connection of the
equipment-grounding conductor can result in a risk
of electric shock. Check with e qualified electrician
or servicemen if you are in doubt us to whether the
appliance is properly grounded.
Installation
GROUNDING INSTRUCTIONS {Cont.}
Do not modify the plug provided with the appliance. If it
will not fit the outlet, have a proper outlet installed by a
qualified electrician.
B.Fordirect-wire connected appliance:
This appliance must be connected to a grounded, metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment grounding terminal or lead
on the appliance.
ELECTRICAL CONNECTION LOCATION
24" MODELS 27" MODELS
CONNECTING DRYER USING 3-WIRE
CONNECTION
GREEN GROUND
GROUND STRAP
SCREW
NOT
WIRE STRAINRELIEF
BRACKET
3/4",UL
RECOGNIZED
RELIEF
NEUTRAL
(White) HOT
WIRE
] #i0 AWGMINIMUMCOPPER
COVER CONDUCTORSOR220/240V]ORPOWER
SUPPLYCORDKITMARKEDFORUSE
WITHDRYERS&PROVIDEDWITHCLOSED
LOOPORSPADETERMINALSWITH
3-wi re Connection UPTURNEDENDS{NOTSUPPLIED},
Not for use in Canada.
DONOTuse for Mobile Home Installations.
NOTfor use on new construction.
NOTfor use on recreational vehicles.
NOTfor use in areas where local codes prohibit grounding
through the neutral conduction.
1.Turn off the circuit breaker(s) (50 amp) or remove the
dryer's circuit fuse at the electrical box.
2. Be sure the appliance cord isunplugged from the wall.
3. Removethe power cord cover located at the lower back.
4. Install 3/4 in. UL recognized strain relief to power cord
entry hole. Bring power cord through strain relief.
nstructions
5. Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of the
terminal block (marked L1 and L2).
B.Connect the neutral (white) line to the center of the
terminal block (marked N).
6. Be sure ground strap is connected to neutral (center)
terminal of block and to green ground screw on cabinet
rear.Tighten all terminal block screws (3)securely.
7. Properly secure power cord to strain relief.
8. Reinstall the cover.
_:LVV/AKI_Iil_I_: NEVER LEAVE THE
COVER OFF OF THE TERMINAL BLOCK.
CONNECTING APPLIANCE USING 4-WIRE
CONNECTION {MUST BE USED FOR
MOBILE HONE INSTALLATION}
NOTES:Since January 1,1996, the National Electric code
requires that the new constructions utilize a 4-wire
connection to an electric dryer.
WARN ING:onlya4-conductorcordshallbe
used when the appliance is installed in a location where
grounding through the neutral conductor is prohibited.
Grounding through the neutral is prohibited for the new
branch-circuit installations, mobile homes, recreational
vehicles, and areas where local codes prohibit grounding
through the neutral conduction.
REHOVEGROUNDSTRAP
ANDDISCARDKEEPGREEN
GROUNDSCREW[oF_ WIRE RELOCATEGREEN
GROUNDSCREW
"\_,_ HERE GREENOR
RELIEF
BRACKET
COVER
HOT
WIRE
3/4",UL /_
RECOGNIZED
STRAIN RELIEF
4 #10 AWGMINiMUMCOPPER
CONDUCTORSOR120/240V 30A POWER
SUPPLYCORDKIT MARKEDFORUSE
WITHDRYERS& PROVIDEDWITH
CLOSEDLOOPORSPADETERMINALS
WITHUPTURNEDENDS(NOTSUPPLIED)
1.Turn off the circuit breaker (s)(30 amp) or remove the
dryer's circuit fuse at the electrical box.
2. Be sure the appliance cord is unplugged from the wall
receptacle.
3. Removethe power cord cover located at the lower back.
4. Remove and discard ground strap. Keep the green
ground screw for step 7.
5. Install 3/4 in. ULrecognized strain relief to power cord
entry hole. Bring power cord through strain relief.
Installation instructions
CONNECTING APPLIANCE USING 4-WIRE
CONNECTION (MUST BE USED FOR
MOBILE HOME INSTALLATION} (Cont.}
6.Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of the
terminal block (marked L! and L2).
B.Connect the neutral (white) line to the center of the
terminal block (marked N).
7.Attach ground wire of power cord with the green ground
screw (hole above strain relief bracket). Tighten all
terminal block screws (:3)securely.
8. Properly secure power cord to strain relief.
9. Reinstall the cover.
JLWf_KI_Iil_I_: NEVER LEAVE THE
COVER OFF OF THE TERMINAL BLOCK.
EXHAUST INFORMATION
WARNING - IN CANADAANDIN
THE UNITED STATES, THE REQUIRED EXHAUST
DUCT DIAMETER IS 4 IN (102ram). DO NOT
USE DUCT LONGER THAN SPECIFIED IN THE
EXHAUST LENGTH TABLE.
Using exhaust longer than specified length will:
, Increase the drying times and the energy cost.
, Reduce the dryer life.
, Accumulate lint, creating a potential fire hazard.
The correct exhaust installation isYOURRESPONSIBILITY.
Problems due to incorrect installation are not covered by
the warranty.
Removeand discard existing plastic or metal foil transition
duct and replace with ULlisted transition duct.
The MAXIMUM ALLOWABLEduct length and number of
bends of the exhaust system depends upon the type of
duct, number of turns, the type of exhaust hood (wall cap),
and all conditions noted below. Themaximum duct length
for rigid metal duct isshown in the following table.
27" DRYER EXHAUST LENGTH
RECOMMENDEDMAXIMUMLENGTH
Exhaust Hood Types
Recommended
Use only for short
run installations
_'1DIA
.......
Rigid
Metal
56 Feet
48 Feet
40 Feet
32 Feet
No, of 90 ° Rigid
Elbows Metal
0 42 Feet
1 34 Feet
2 26 Feet
3 18 Feet
EXHAUST INFORMATION (cont.}
24" DRYER EXHAUST LENGTH
RECOMMENDED MAXIMUM LENGTH
Exhaust Hood Tgpes
Recommended
Use onlg for short
run installations
4" DIA
_'d I_ 2 1/2"
No. of 90 ° Rigid
Elbows Metal
0 /43 Feet 36 Feet
i 33 Feet 26 Feet
2 24 Feet 16 Feet
, For every additional 90° elbow, reduce the allowable vent
systemlength by 10ft.
, Two 45°elbows will betreated likeone 90°elbow. Forthe side
exhaust installations,add one 90°elbow to the chart.
, Thetotal vent system length includes allthe straight portions
and elbows of the system (transition duct included).
EXHAUST SYSTEM CHECK LIST
HOOD ORWALL CAP
, Terminate in a manner to prevent back drafts or entry of
birds or other wildlife.
, Termination should present minimal resistance to
the exhaust air fiow and should require little or no
maintenance to prevent clogging.
,Never install a screen in or over the exhaust duct. This
could cause lint build up.
, Wall caps must be installed at least 12 in. above ground
level or any other obstruction with the opening pointed
down.
SEPARATIONOFTURNS
For best performance, separate all turns by at least 4 ft.
of straight duct, including distance between last turn and
exhaust hood.
TURNSOTHERTHAN 90°
* One turn of 45oor less may be ignored.
* Two 45oturns should be treated as one 90oturn.
* Eachturn over 45oshould be treated as one 90oturn.
SEALING OFJOINTS
. All joints should be tight to avoid leaks. The male end of
each section of duct must point away from the dryer.
* Donot assemble the ductwork with fasteners that extend
into the duct. They will serve as a collection point for lint.
, Duct joints can be made air and moisture-tight by
wrapping the overlapped joints with duct tape.
, Horizontal runs should slope down toward the outdoors
1/4 inch per foot
INSULATION
Duct work that runs through an unheated area or isnear air
conditioning should be insulated to reduce condensation
and lint build-up.
Installation
[] EXHAUST CONNECTION
, WARNING - TO REDUCE THE
RISK OF FIRE OR PERSONAL INJURY:
. This appliance must be exhausted to the outdoors.
. Use only 4" rigid metal ducting for the home exhaust
duct.
, Use only 4" rigid metal or UL-listed flexible metal
(semi-rigid or foil-type) duct to connect the dryer to the
home exhaust duct. It must be installed in accordance
with the instructions found in "Connecting The Dryer
To House Vent" on page 8 of this manual.
. Donot terminate exhaust in a chimney, a wall, a ceiling,
gas vent, crawl space, attic, under an enclosed floor,
or in any other concealed space of a building. The
accumulated lint could create a potential fire hazard.
, Never terminate the exhaust into a common duct with
a kitchen exhaust system. A combination of grease
and lint creates a potential fire hazard.
, Do not use duct longer than specified in the exhaust
length table. Longer ducts can accumulate lint,
creating a potential fire hazard.
, Never install a screen in or over the exhaust duct. This
will cause lint to accumulate, creating a potential fire
hazard.
, Do not assemble ductwork with any fasteners that
extend into the duct. These fasteners can accumulate
lint, creating a potential fire hazard.
, Do not obstruct incoming or exhausted air.
, Provideanaccessfor inspectionandcleaningoftheexhaust
system,especiallyat turns andjoints. Exhaustsystemshall
be inspectedand cleanedat leastonceayear.
THIS DRYER COMES READY FOR REAR
EXHAUSTING. IF SPACE IS LIMITED, USE
THE INSTRUCTIONS IN SECTION 6 TO
EXHAUST DIRECTLY FROM THE SIDES OR
BOTTOM OF THE CABINET.
STANDARD REAR EXHAUST
Forstraight lineinstallation,connect
the drger exhaustto theexternal
exhausthood usingduct tape or
clamp.
EXTERNALDUCT
OPENING
DUCTTAPEOR
DUCTCLAMP
4" METAL DUCTCUT
TO PROPERLENGTH
DUCTTAPEOR
DUCTCLAMP
®
°°i ©© O
nstructions
STANDARD REAR EXHAUST
(Vented above floor level}
AGE
NOTE: ELBOWS WILL PREVENT DUCT KINKING AND COLLAPSING
ELBOW HIGHLY
RECOMMENDED
[5]LEVELINGAND STABILIZINGYOURAPPLIANCE
FRONT-TO-BACK,
[t¢l
2LEVELINGLEGS
Level and stabilizing your appliance
!. Carefully move the appliance to its final location. Gently rock
the appliance into position. It isimportant not to damage the
rubber leveling legswhen moving your appliance to its final
location. Damaged legs can increase appliance vibration. It
may be helpful to spray window cleaner on the floor to help
move your appliance to its final position.
Note: Do not use washer cover to lift the unit.
2.To ensure the appliance is level and solid on all four legs,
tilt the appliance forward so the rear legs are off the
ground. Gently set the appliance back down to allow the
rear legs to self adjust.
3.With the appliance in its final position, place a level on top
of back part of the washer lid and check it side to side,
then check front to back. Screw the front leveling legs up
or down to ensure the appliance is resting solid on all four
legs (no rocking or the appliance should exist), turn the
lock nuts on each leg up toward the base of the unit and
snug with a wrench.
Note: Keepthe leg extension at minimum to prevent excessive
vibration. Thefarther out legs are extended, the more the unit
will vibrate.
7
Installation instructions
CONNECTING THE DRYERTO HOUSEVENT
RIGIDMETALTRANSITIONDUCT
Forbest drying performance, a rigid metal transition duct is
recommended.
Rigidmetal transitions ducts reduce the risk of crushing and
kinking.
UL-LISTEDFLEXIBLEMETAL(SEMI-RIGID}TRANSITIONDUCT
If rigid metal duct cannot be used,then UL-listedflexible metal
(semi-rigid)ducting can beused(KitWX08X10077).
Neverinstallflexiblemetal duct in walls,ceilings,floors or other
enclosedspaces.
Total length of flexible metal duct should not exceed 8 feet
(2.4m).
Formanyapplications,installingelbows at both the dryerand
the wall ishighlyrecommended(seeillustrations).Elbowsallow
the appliance to sit closeto the wall without kinking and or
crushingthe transitionduct, maximizingdryingperformance.
Avoidrestingtheduct onsharpobjects.
UL-LISTEDFLEXIBLEMETAL(FOIL-TYPE}TRANSITIONDUCT
In special installations,it may be necessaryto connect the
dryerto the housevent usinga flexible metal (foil-type)duct.
A UL-listedflexible metal (foil-type)ductmay be usedONLYin
installations where rigid metal or flexible metal (semi-rigid)
ducting cannot be used AND where a 4" diameter can be
maintainedthroughout theentirelengthof thetransitionduct.
InCanadaandtheUnitedStates,onlytheflexiblemetal(foil-type)
ductsthat complywith the"Outlinefor ClothesDryerTransition
DuctSubject2158A"shallbeused.
Neverinstallflexiblemetal duct in walls,ceilings,floors or other
enclosedspaces.
Total length of flexible metal duct should not exceed 8 feet
(2.4m).
Avoidrestingtheduct onsharpobjects.
Forbest dryingperformance:
1.Slideoneend ofthe duct overthe clothesdryeroutlet pipe.
2.Securetheduct with a clamp.
3.With the dryer in its permanent position,extendthe duct to
its full length.Allow 2" of duct to overlapthe exhaustpipe.
Cutoff and removeexcessduct. Keepthe duct asstraightas
possiblefor maximum airflow.
4.Securetheduct to the exhaustpipewith theother clamp.
DO
ELBOW HIGHLY
RECOMMENDED
;2
DO NOT USE
EXCESSIVE
DON'T
EXHAUST
8
Installation instructions
_-124" MODELS ONLY:
DRYER EXHAUST TO RIGHT, LEFT OR
BOTTOM CABINET
_WARNING - BEFOREPERFORMING
THIS EXHAUST INSTALLATION, BE SURE
TO DISCONNECT THE APPLIANCE FROM
ITS ELECTRICAL SUPPLY. PROTECT YOUR
HANDS AND ARMS FROM SHARP EDGES
WHEN WORKING INSIDE THE CABINET. BE
SURE TO WEAR GLOVES.
For downward venting, rotate elbow
sections so that elbow points downward
REMOVE
DESIRED
KNOCKOUT
(ONLY1)
ADDING ELBOW AND DUCT FOR
EXHAUST TO LEFT OR RIGHT SIDE OF
CABINET
, Rotate elbow sections so that the opening points to the
sideto which you want to vent. Preassemble 4"elbow with
4" duct. Use only 4" UL approved rigid metal for ducting
inside the dryer.
, Connect duct assembly to the internal elbow.
WARNING- Sesurenottopullordamagethe
electrical wires inside the dryer when inserting the duct,
4" UL approved rigid metal
i DUCT
........ i..[j ...... TAPE
, Apply duct tape as shown on the joint between the dryer
internal duct and the straight duct pipe.
AWARNING-
Internal duct joints must be
_ ecured with tope, otherwise
they may separate and cause
a safety hazard.
27" MODELS ONLY:
DRYER EXHAUST TO RIGHT, LEFT OR
BOTTOM CABINET
THIS EXHAUST INSTALLATION, BE SURE
TO DISCONNECT THE APPLIANCE FROM
ITS ELECTRICAL SUPPLY. PROTECT YOUR
HANDS AND ARMS FROM SHARP EDGES
WHEN WORKING INSIDE THE CABINET. BE
SURE TO WEAR GLOVES.
For downward venting, rotate elbow
sections so_
EXHAUST TO LEFT OR RIGHT SIDE OF
CABINET
, Rotate elbow sections so that the opening points to the
sideto which you want to vent. Preassemble 4" elbow with
4" duct. Use only 4" UL approved rigid metal for ducting
inside the dryer.
* Connect duct assembly to the internal elbow.
,_ WARNING- Besure not to pull or damage the
electrical wires inside the dryer when inserting the duct.
, Apply duct tape as shown on the joint between the dryer
internal duct and the straight duct pipe.
AWARNING-
H Internal duct joints must be
secured with tope, otherwise
they may separate and cause
a safety hazard.
Installation
If]PLUMBING INFORMATION
WATER SUPPLY REQUIREMENTS
. HOTAND COLDWATERFAUCETS- Must bewithin 42" of
the appliance water inlet hose connections. The faucets
must be 3/4" garden hose-type so inlet hoses can be
connected.
. WATERPRESSURE- Must be between !0 and 120 pounds
per square inch with a maximum unbalance pressure,
hot vs.cold flowing, of !0 pounds per square inch.
. WATERTEMPERATURE- Water heater should be set to
deliver !20°F (50°C) in the washer when HOT wash is
selected.
, SHUT-OFFVALVES- Both hot and cold water shut-off
valves (faucets) should be supplied.
. LOCATION- Do not install appliance in an area where the
temperature will fall below freezing. If appliance isstored
or transported in freezing temperatures, be sure all water
from the fill and drain systems has been removed.
DRAIN REQUIREMENTS
. DRAIN RATE- The drain or standpipe must be capable
of accepting a discharge at the rate of 16 gallons per
minute.
, DRAINHEIGHT- The drain height must be 33" minimum
and 96" maximum.
. STANDPIPEDIAMETER- The standpipe diameter must
be 1-1/2" minimum. There MUSTbe an air gap around
the drain hose in the standpipe. A snug fit can cause a
siphoning action.
, SIPHONBREAKKIT- Fora drain facility lessthan 33" high,
the hose, coupling and clamps provided in the machine
must be used and, in addition, a siphon break MUSTbe
installed on the back of the machine. Use Siphon Break
Kit WH49X228 and follow instructions in the kit.
Instructions
[8-1CONNECTING TO PLUMBING FACILITIES
Ifnot installed,install rubberwasher in oneendof hotwater hose.
Thread hot water hose onto connection labeled H at top rear
of washer. Handtighten, plus an additional 1/8 turn with pliers.
If not installed, install rubber washer in one end of cold water
hose.Threadcold water hoseonto connection labeled Cat top
rear of washer. Hand tighten, plus an additional 1/8 turn with
pliers.
Moveapplianceasclosetofinal location aspossible,leavingroom
for you to make water, drain, electrical and vent connections to
your home.
NOTE: If longer drain hose
is required, order drain hose
extension kit, part number
WH49X301.Connect additional
drain hose (contained in kit)to
original hose with hose clamp
(contained in kit).
Insertfreeendof drain hoseinto
drain opening of your home up
to drain hose stopper (do not
removehosestopper itprevents
siphoning). If water valves and
drain are built into wall, fasten
drain hose to one of water
hoses with cable tie provided
(ribbed side on inside). If your
drain isa standpipe,fastendrain
hoseto standpipe with cabletie
provided.
10
Installation instructions
[_]MOBILE OR MANUFACTURED HOME
INSTALLATION
. Installation MUSTconform to the MANUFACTUREDHOME
CONSTRUCTION& SAFETYSTANDARD,TITLE 24, PART
32-80 or, when such standard is not applicable, with
AMERICAN NATIONAL STANDARD FOR MOBILE HOME,
ANSl/NFPA NO. 501B.
. The appliance MUST be vented to the outdoors with
the termination securely fastened to the mobile home
structure,
. The vent MUST NOT be terminated beneath a mobile or
manufactured home.
. The vent duct material MUSTBEMETAL.
KIT14-D346-33MUSTbeusedto attach theappliancesecurely
to the structure.
Thevent MUSTNOTbe connectedto any other duct, vent, or
chimney.
. Do not use sheet metal screws or other fastening devices
which extend into the interior of the exhaust vent.
. See section 2 for electrical connection information.
[i-0-IALCOVE OR CLOSET INSTALLATION
. If your appliance is approved for installation in an alcove
or closet, it will be stated on a label on the appliance
back.
. TO PREVENTLARGEAMOUNTSOFLINTAND MOISTURE
FROMACCUMULATINGANDTO MAINTAINDRYING
EFFICIENCY,THISMACHINEMUSTBEEXHAUSTED
OUTDOORS.
. Do not install this appliance with lessthan the minimum
clearances shown above.
CONSIDERATION MUST BE GIVEN TO PROVIDE
ADEQUATE CLEARANCES FOR INSTALLATION AND
SERVICE.
AWARNING: DoNOTINSTALLTHIS
APPLIANCEIN A CLOSETWITH A SOLID DOOR.
DOOR VENTILATION OPENING (27" MODELS)
A minimum of 120 square inches of opening, equally divided
at top and bottom, is required. Air openings are required to
be unobstructed when a door is installed. A Iouvered door
with equivalent air openings for the full length of the door
isacceptable.
When louvers or registers are placed in door openings, the
free air openings of the louvers or registers must equal 120
square inches.
DOOR VENTILATION OPENING (24" MODELS)
27" Model
I Sq.In.
/_0 /
li: Iit qn
A minimum of 72 square inches of opening is required. Air
openings are required to be unobstructed when a door is
installed. A Iouvered door with equivalent air openings for
the full length of the door is acceptable.
When louvers or registers are placed in door openings, the
free air openings of the louvers or registers must equal 72
square inches.
24,,Model__ Sqln
/Ill ', _Sq .In.
[n7BATHROOM OR BEDROOM INSTALLATION
. The appliance MUST be vented to the outdoors. See
EXHAUSTINFORMATION section 3 & 4.
, The installation must conform with local codes or, in the
absence of local codes, with the NATIONAL ELECTRICAL
CODE,ANSI/NFPA NO. 70.
11
Installation instructions
[] SERVICING
,WARNING- LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING
CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION
AFTER SERVICING/INSTALLATION.
Forreplacement parts and other information, refer to Owner's Manual for servicing phone numbers.
REGISTERYOUR NEW APPLIANCE TO RECEIVEANY
IIvlPORTANTPRODUCT NOTIFICATIONS.
Please go to www.GEAppliances.com or mail in your
Product Registration Card.
Forquestions on installation, call: 800.626.2000 (US)or
800-56!-3344 (Canada).
12
Instructions d'Installation
iT21REPARATION
AVERTISSEMENT- HARQUEZ TOUS LES FILS AVANT LE DEBRANCHEMENT
LORSQUE VOUS EFFECTUEZ UN CONTROLE POUR REPARATION. LES ERREURS DE
BRANCHEMENT PEUVENT CAUSEES DES PROBLEMES DE FONCTIONEMENT APRES
REPARATION ET D'INSTALLATION.
Pour les pisces de rechc]nge et (]utres informc]tions, veuillez reporter (]u Manuel de I'Utilisc]teur pour les num#ros de
t#l#phone du service c]pr_svente.
ENREGISTREZVOTRE NOUVEL APPAREIL POUR OUE
VOUS RECEVIEZDES INFORiVlATIONSIIPORTANTES
SUR LE PRODUIT.
Allez, SVP,sur notre site www.GEAppliances.com ou
envoyez par la poste votre Carte d'inscription du produit
Pour des questions sur I'instc]llc]tion,composez:
800.626.2000 (E.U.)ou 800.56!.334/4 (Cc_nodo)
12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

GE 2661532110 Installation guide

Category
Electric laundry dryers
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI