Sony TAV-L1 Operating instructions

2-670-721-11(4)

TAV-L1

TV Integrated AV System

Operating Instructions

2

GB

Before operating the system, please read the

“Safety Information” section of this manual.

Retain this manual for future reference.

NOTICE FOR

CUSTOMERS

A moulded plug complying with BS1363 is fitted to

this equipment for your safety and convenience.

Should the fuse in the plug supplied need to be

replaced, a 13 AMP fuse approved by ASTA or BSI to

BS 1362 (i.e., marked with or ) must be used.

When an alternative type of plug is used it should be

fitted with a 13 AMP FUSE, otherwise the circuit

should be protected by a 13 AMP FUSE at the

distribution board.

If the plug supplied with this equipment has a

detachable fuse cover, be sure to attach the fuse cover

after you change the fuse. Never use the plug without

the fuse cover. If you should lose the fuse cover,

please contact your nearest Sony service station.

How to replace the fuse

Open the fuse compartment with a blade screwdriver,

and replace the fuse.

• This apparatus has to be connected to a mains socket outlet

with a protective earthing connection.

• To prevent the risk of electric shock, if the mains lead or

plug is damaged, do not insert the plug into the mains

socket outlet. This plug cannot be used and should be

destroyed.

• Dangerously high voltages are present inside the system.

Do not open the cabinet. Refer servicing to qualified

personnel only.

• Do not install the appliance in a confined space, such as a

bookcase or built-in cabinet.

To reduce the risk of fire or electric shock, do not

expose this apparatus to rain or moisture.

To prevent fire, do not cover the ventilation of the apparatus

with news papers, table-cloths, curtains, etc. And don’t place

lighted candles on the apparatus.

To prevent fire or shock hazard, do not place objects filled

with liquids, such as vases, on the apparatus.

Don’t throw away the battery with general

house waste, dispose of it correctly as

chemical waste.

This appliance is classified as a

CLASS 1 LASER product. This

marking is located on the rear of

the unit.

Disposal of Old Electrical &

Electronic Equipment

(Applicable in the European

Union and other European

countries with separate

collection systems)

This symbol on the product or on

its packaging indicates that this

product shall not be treated as

household waste. Instead it shall

be handed over to the applicable

collection point for the recycling

of electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent

potential negative consequences for the environment and

human health, which could otherwise be caused by

inappropriate waste handling of this product. The recycling

of materials will help to conserve natural resources. For more

detailed information about recycling of this product, please

contact your local Civic Office, your household waste

disposal service or the shop where you purchased the

product.

Thank you for choosing this Sony product.

Before operating the system, please read this manual

thoroughly and retain it for future reference.

Trademark information

• is a registered trademark of the DVB project.

• “PlayStation” is a trademark of Sony Computer

Entertainment, Inc.

• Manufactured under license from Dolby Laboratories.

“Dolby,” “Pro Logic,” and the double-D symbol are

trademarks of Dolby Laboratories.

• Manufactured under license from Digital Theater

Systems, Inc.

“DTS” and “DTS Digital Surround” are registered

trademarks of Digital Theater Systems, Inc.

• This system incorporates

High-Definition Multimedia

Interface (HDMI™) technology. HDMI, the HDMI logo

and High-Definition Multimedia Interface are trademarks

or registered trademarks of HDMI Licensing LLC.

WARNING

FUSE

Disposal of the system

Introduction

3

GB

Table of Contents

NOTICE FOR CUSTOMERS ...................... 2

How to replace the fuse .................................... 2

About this manual ....................................... 5

Safety information ....................................... 5

Precautions ................................................. 8

Notes about the discs ....................................... 9

Guide to basic operations of this

system.................................................. 10

Overview of the remote ............................. 11

Overview of the system/lift unit buttons and

indicators.............................................. 13

Basic Operations

1: Checking the accessories......................14

2: Inserting batteries into the remote .........14

3: Connecting a TV aerial/VCR/

DVD player ...........................................15

4: Connecting the FM wire antenna

(aerial) ..................................................16

5: Switching on the system........................17

6: Auto-tuning the TV.................................18

7: Selecting the DVD language

(Quick Setup)........................................19

: for digital channels only

Watching TV ..............................................20

Checking the Digital Electronic Programme

Guide (EPG) ................................22

Using the Favourite list .....................24

Viewing pictures from connected

equipment.............................................25

Available discs...........................................26

System sound feature................................28

Playing discs..............................................30

Various play modes..........................................31

(PBC Playback)

(Resume Play)

Searching for a particular point or a scene on a

disc.............................................................33

(Scan, Slow-motion Play, Freeze Frame)

(Picture Navigation)

Displaying various angles and subtitles ..........34

Listening to the FM radio ...........................35

Presetting FM radio stations......................36

Getting Started

Watching TV

Enjoying Discs

Enjoying the FM Radio

Continued

4

GB

Advanced Operations

Navigating through menus ........................ 37

Picture Adjustment menu .......................... 38

Sound Adjustment menu........................... 39

Screen menu............................................. 40

Features menu .......................................... 41

Timer menu ............................................... 42

Set Up menu ............................................. 43

Navigating through DVD’s menu............... 49

Enjoying DivX

®

videos .............................. 49

Navigating through menus ........................ 51

Overview of the menus.................................... 51

Searching/selecting the disc ..................... 53

Searching for a title/chapter/track/scene, etc. 53

Selecting [ORIGINAL] or [PLAY LIST] on a DVD-

R/DVD-RW ................................................. 54

Viewing information about the disc ................. 54

Using the play mode ................................. 56

Creating your own programme ....................... 56

(Programme Play)

Playing in random order.................................. 57

(Shuffle Play)

Playing repeatedly........................................... 58

(Repeat Play)

Enjoying the slide show............................. 59

About MP3 audio tracks and JPEG image files ..

59

Playing DATA CDs or DATA DVDs with MP3

audio track and JPEG image files ............. 60

Playing audio tracks and images as a slide show

with sound ................................................. 61

Locking discs............................................. 63

(CUSTOM PARENTAL CONTROL, PAREN-

TAL CONTROL)

Using the Setup Display............................ 65

Overview of the items.......................................69

Enjoying the sound at low volume....................70

(AUDIO DRC)

Enjoying a bilingual DVD disc..........................70

(DUAL MONO)

Reinforcing bass frequencies ..........................71

(SW LEVEL)

Using the lift function........................................71

(Lift Mode)

Connecting optional equipment .................73

Specifications ............................................76

PC specifications .............................................77

Language code list (DVD function only) ..........78

Troubleshooting.........................................79

Self-diagnosis function (DVD function only).....84

Index..........................................................85

Using the TV Menu

Using the DVD’s Menu

Using the Player Control Menu

Using the Lift Unit/Front Panel

Display

Using Optional Equipment

Additional Information

5

GB

About this manual

• The instructions in this manual describe the controls on

the remote. You can also use the controls on the system if

they have the same or similar names as those on the

remote.

• The Control Menu items may be different depending on

the area.

• “DVD” may be used as a general term for DVD VIDEOs,

DVD+RWs/DVD+Rs, and DVD-RWs/DVD-Rs.

• The following symbols are used in this manual.

*1 MP3 (MPEG1 Audio Layer 3) is a standard format defined by

ISO/MPEG which compresses audio data.

*2 DivX

®

is a video file compression technology, developed by

DivX, Inc.

*3 DivX, DivX Certified, and associated logos are trademarks of

DivX, Inc. and are used under license.

Safety information

AC power cord (mains

lead)

• Unplug the AC power

cord (mains lead)

when moving the

system. Do not move

the system with the

AC power cord

(mains lead) plugged in. It may damage the AC power

cord (mains lead) and result in fire or electric shock.

• If you damage the AC power cord

(mains lead), it may result in fire or

electric shock.

– Do not pinch, bend, or twist the

AC power cord (mains lead)

excessively. The core conductors

may be exposed or broken,

causing a short-circuit, which

may cause fire or electric shock.

– Do not modify or damage the AC

power cord (mains lead).

– Do not put anything heavy on the

AC power cord (mains lead). Do

not pull the AC power cord

(mains lead).

– Keep the AC power cord (mains lead) away from heat

sources.

– Be sure to grasp the plug when disconnecting the AC

power cord (mains lead).

• If the AC power cord (mains lead) is damaged, stop using

it and ask your dealer or Sony service centre to exchange

it.

• Do not use the supplied AC power cord (mains lead) on

any other equipment.

• Use only an original Sony AC power cord (mains lead),

not other brands.

AC power cord (mains lead)/

cable protection

Pull out the AC power cord (mains

lead)/cable by the plug. Do not

pull on the AC power cord (mains

lead)/cable itself.

AC power source (mains)

Do not use a poor fitting mains socket. Insert

the plug fully into the mains socket. A poor fit

may cause arcing and result in fire. Contact

your electrician to have the mains socket

changed.

Symbol Functions available for

DVD VIDEOs, DVD-Rs/DVD-

RWs in video mode, and

DVD+Rs/DVD+RWs

DVD-Rs/DVD-RWs in VR

(Video Recording) mode

VIDEO CDs (including Super

VCDs or CD-Rs/CD-RWs in

video CD format or Super VCD

format)

Super Audio CDs

Music CDs or CD-Rs/CD-RWs in

music CD format

DATA CDs (CD-ROMs/CD-Rs/

CD-RWs containing MP3*

1

audio

tracks, JPEG image files, and

DivX*

2

*

3

video files)

DATA DVDs (DVD-ROMs/

DVD-Rs/DVD-RWs/DVD+Rs/

DVD+RWs containing MP3*

1

audio tracks, JPEG image files,

and DivX*

2

*

3

video files)

Continued

6

GB

Notes about moving the lift unit up/down

• The lift unit moves up and down

automatically when the system is

turned on/off, and when the input is

switched with “AUTO” selected in

“Lift Mode” (page 72). You can also

make the lift unit move up/down by

pressing .

• To prevent operational mistakes, this

system features a “LOCK” function

(page 72).

• When connecting other components to the side of the

system (e.g., AV 4 connections), make sure not to place

any cords under the lift unit to avoid trapping them as the

lift unit moves.

• Do not touch the lift unit (especially the circled areas in

the right illustration) while it is moving. Especially, watch

out for small children.

• Do not operate this system while the lift unit is moving.

Medical institutions

Do not place this system in a

place where medical equipment is

in use. It may cause malfunction

of medical instruments.

Carrying

• Before relocating the system,

perform the procedure in “On

moving the system” (page 9), then

disconnect all the cables from the

system.

• When you carry the system by hand,

hold the system as illustrated on the

right. If you do not do so, the system

may fall and be damaged or cause serious injury. If the

system has been dropped or damaged, have it checked

immediately by qualified service personnel.

• When transporting it, do not subject the system to jolts or

excessive vibration. The system may fall and be damaged

or cause serious injury.

• When you carry the system in for repair or when you move

it, pack it using the original carton and packing material.

• Carrying the system requires two or more people.

Ventilation

• Never cover the ventilation holes

in the cabinet. It may cause

overheating and result in fire.

• Unless proper ventilation is

provided, the system may gather

dust and get dirty. For proper

ventilation, observe the

following:

– Do not install the system turned backwards or

sideways.

– Do not install the system turned over or upside down.

– Do not install the system on a shelf or in a closet.

– Do not place the system on a rug or bed.

– Do not cover the system with cloth, such as curtains, or

items such as newspapers, etc.

• Never install the system as follows:

Ventilation holes

• Do not insert anything in the ventilation

holes, gaps between the TV screen and the

lift unit or the disc slot. If metal or liquid

is inserted in these holes, it may result in

fire or electric shock.

• If anything falls into the cabinet, unplug

the unit and have it checked by qualified

personnel before operating it any further.

• Do not block the ventilation slots by putting anything on

the system. The system is equipped with a high power

amplifier. If the ventilation slots are blocked, the unit can

overheat and malfunction.

Placement

• Do not obstruct the area where the lift unit moves up and

down. It may cause a malfunction. Leave some space

around the system. Otherwise, air-circulation may be

inadequate and cause overheating, which may cause fire

or damage to the system or the lift unit.

• Never place the system in hot,

humid or excessively dusty places.

• Do not install the system where

insects may enter.

• Place the system on a stable, level

surface. Otherwise, the system may

fall and cause injury.

• Do not install the system in a location

where it may protrude, such as on or

behind a pillar, or where you might

bump your head on it. Otherwise, it may

result in injury.

Air circulation is

blocked.

Air circulation is

blocked.

Wall Wall

30 cm

Leave at

least this

much

space.

10 cm

Do not place any objects under the area

where the lift unit moves up/down.

7

GB

Water and moisture

• Do not use this system near

water – for example, near a

bathtub or shower room. Also do

not expose to rain, moisture or

smoke. This may result in fire or electric shock.

• Do not touch the AC power cord

(mains lead) and the system with wet

hands. Doing so may cause electric

shock or damage to the system.

Moisture and flammable objects

• Do not let this system get wet. Never

spill liquid of any kind on the system.

If any liquid or solid object does fall

through openings in the cabinet, do

not operate the system. It may result

in electric shock or damage to the

system.

Have it checked immediately by

qualified service personnel.

• To prevent fire, keep flammable

objects (candles, etc.) and electric bulbs away from the

system.

Oils

Do not install this system in restaurants that use oil. Dust

absorbing oil may enter and damage the system.

Fall

Do not allow children to

climb up on or hang from

the system.

Vehicle or ceiling

Do not install this system in a

vehicle. The motion of the vehicle

may cause the system to fall down

and cause injury. Do not hang this

system from the ceiling.

Ships and other vessels

Do not install this system on a ship

or other vessel. If the system is

exposed to seawater, it may cause

fire or damage the system.

Outdoor use

• Do not expose the system to

direct sunlight. The system may

heat up and this may result in

damage to the system.

• Do not install this system

outdoors.

Wiring

• Unplug the AC power cord (mains lead) when wiring

cables. When hooking up, be sure to unplug the AC power

cord (mains lead) for your safety.

• Take care not to catch your feet on the cables. It may

damage the system.

Cleaning

• Unplug the AC power cord (mains lead)

when cleaning the plug and this system. If

you do not, it may result in electric shock.

• Clean the mains plug regularly. If the plug

is covered with dust and it picks up

moisture, its insulation may deteriorate

and result in fire.

Lightning storms

For your own safety, do not touch any

part of the system, AC power cord

(mains lead), or aerial lead during

lightning storms.

Damage requiring service

If the surface of the system cracks, do not touch it until you

have unplugged the AC power cord (mains lead). Otherwise

electric shock may result.

Servicing

Do not open the cabinet.

Entrust the system to qualified

service personnel only.

Small accessories removal and fittable

Keep accessories out of children’s reach. If they are

swallowed, choking or suffocation may occur. Call a doctor

immediately.

Broken glass

Do not throw anything at the system. The

screen glass may explode by the impact

and cause serious injury.

When not in use

For environmental and safety

reasons, it is recommended that

the system is not left in standby

when unused. Disconnect from

the AC power source (mains).

However, some systems may

have features which need the

system to be left in standby to work correctly. The

instructions in this manual will inform you if this applies.

Viewing the TV screen

• To view the TV screen comfortably, the recommended

viewing position is from four to seven times the screen’s

vertical length away from the system.

• View the TV screen in moderate light, as viewing the TV

screen in poor light strains your eyes. Watching the screen

continuously for long periods of time can also strain your

eyes.

Continued

8

GB

Volume adjustment

• Adjust the volume so as not to trouble your neighbours.

Sound carries very easily at night time. Therefore, closing

the windows or using headphones is suggested.

• When using headphones, adjust the volume so as to avoid

excessive levels, as hearing damage may result.

• Do not turn up the volume while listening to a section with

very low level inputs or no audio signals. If you do, the

speakers may be damaged when a peak level section is

suddenly played.

Overloading

This system is designed to operate on

a 220–240 V AC supply only. Take

care not to connect too many

appliances to the same mains socket

as this could result in fire or electric

shock.

Heat

Do not touch the surface of the system. It remains hot, even

after the system has been turned off for some time.

Corrosion

If you use this system near the seashore, salt may corrode

metal parts of the system and cause internal damage or fire.

It may also shorten the life of the system. Steps should be

taken to reduce the humidity and moderate the temperature

of the area where the system is located.

Precautions

Safety

• The unit is not disconnected from the AC power source

(mains) as long as it is connected to the wall outlet

(mains), even if the unit itself has been turned off. To

disconnect the system completely, pull the plug from the

AC power source (mains).

• Unplug the unit from the wall outlet (mains) if you do not

intend to use it for an extended period of time.

LCD Screen

• Although the LCD screen is made with high-precision

technology and 99.99% or more of the pixels are effective,

black dots may appear or bright points of light (red, blue,

or green) may appear constantly on the LCD screen. This

is a structural property of the LCD panel and is not a

malfunction.

• Do not expose the LCD screen surface to the sun. Doing

so may damage the screen surface.

• Do not push or scratch the front filter, or place objects on

top of this system. The image may be uneven or the LCD

panel may be damaged.

• If this system is used in a cold place, a smear may occur in

the picture or the picture may become dark.

This does not indicate a failure. These phenomena

disappear as the temperature rises.

• Ghosting may occur when still pictures are displayed

continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this system is in

use. This is not a malfunction.

• The LCD contains a small amount of liquid crystal and

mercury. The fluorescent tube used in this system also

contains mercury. Follow your local ordinances and

regulations for disposal.

Fluorescent lamp

This system uses a special fluorescent lamp as its light

source. If the screen image becomes dark, flickers, or does

not appear, the fluorescent lamp has worn out and should be

replaced. For replacement, consult qualified service

personnel.

Installing the system

• Do not install the system in places subject to extreme

temperature, for example in direct sunlight, or near a

radiator, or heating vent or excessive dust, mechanical

vibration, or shock. If the system is exposed to extreme

temperature, the system may overheat and cause

deformation of the casing or cause the system to

malfunction.

• To obtain a clear picture, do not expose the screen to direct

illumination or direct sunlight. If possible, use spot

lighting directed down from the ceiling.

9

GB

• Do not install optional components too close to the

system. Keep optional components at least 30 cm away

from the system. If a VCR is installed in front of the

system or beside the system, the picture may become

distorted.

• Picture distortion and/or noisy sound may occur if the

system is positioned in close proximity to any equipment

emitting electromagnetic radiation.

• Allow adequate air circulation to prevent internal heat

buildup.

• Do not place the unit on surfaces (rugs, blankets, etc.) or

near materials (curtains, draperies) that may block the

ventilation slots.

• Do not install the unit in an inclined position. It is designed

to be operated in a horizontal position only.

• Keep the unit and discs away from equipment with strong

magnets, such as microwave ovens, or large loudspeakers.

• If the unit is brought directly from a cold to a warm

location, moisture may condense inside this system and

cause damage to the lenses. When you first install the unit,

or when you move it from a cold to a warm location, wait

for about 30 minutes before operating the unit.

Handling and cleaning the screen surface/cabinet of

the system

The screen surface is finished with a special coating to

prevent strong light reflections.

To avoid material degradation or screen coating degradation,

observe the following precautions.

• Do not push on the screen, scratch it with a hard object, or

throw anything at it. The screen may be damaged.

• Do not touch the display panel after operating the system

continuously for a long period as the display panel

becomes hot.

• We recommend that the screen surface be touched as little

as possible.

• To remove dust from the screen surface/cabinet, wipe

gently with a soft cloth. If dust is persistent, wipe with a

soft cloth slightly moistened with a diluted mild detergent

solution. You can wash and repeatedly use the soft cloth.

• Never use any type of abrasive pad, alkaline/acid cleaner,

scouring powder, or volatile solvent, such as alcohol,

benzene, thinner or insecticide. Using such materials or

maintaining prolonged contact with rubber or vinyl

materials may result in damage to the screen surface and

cabinet material.

If you have any questions or problems concerning your

system, please consult your nearest Sony dealer.

• The ventilation holes can accumulate dust over time. To

ensure proper ventilation, we recommend removing the

dust periodically (once a month) using a vacuum cleaner.

On placement

At high volume, over long periods of time, the cabinet

becomes hot to the touch. This is not a malfunction.

However, touching the cabinet should be avoided.

On cleaning discs, disc/lens cleaner

Do not use a commercially available cleaning disc

or disc/lens cleaner (wet or spray type). These may

cause apparatus to malfunction.

On moving the system

When you carry the system, use the following procedure to

protect the inner mechanism.

1 Press (input select) repeatedly to select “DVD.”

2 Make sure that the disc is removed from the system.

3 Press x (stop) and 1 on the system simultaneously.

“MECHA LOCK” appears in the front panel display.

The lift unit is now set in the shipping position (down).

4 Remove the AC power cord (mains lead) from the

wall outlet (mains).

On handling discs

• To keep the disc clean, handle the disc by its edge. Do not

touch the surface.

• Do not stick paper or tape on the disc.

• Do not expose the disc to direct sunlight or heat sources

such as hot air ducts, or leave it in a car parked in direct

sunlight as the temperature may rise considerably inside

the car.

• After playing, store the disc in its case.

On cleaning

• Before playing, clean the disc with a cleaning cloth.

Wipe the disc from the centre out.

• Do not use solvents such as benzine, thinner,

commercially available cleaners, or anti-static spray

intended for vinyl LPs.

This system can only play back a standard circular disc.

Using neither standard nor circular discs (e.g., card, heart, or

star shape) may cause a malfunction.

Do not use a disc that has a commercially available accessory

attached, such as a label or ring.

Notes about the discs

10

GB

Guide to basic

operations of this

system

This system is a TV with DVD player. The lift unit of

this system has built-in 2.1 channel speakers. You can

enjoy high quality and exciting sound from TV, DVD,

FM and other connected components.

About the lift unit

When you select “AUTO” in “Lift Mode” (page 72),

the lift unit moves up/down according to the selected

input. For example, when you watch TV or DVD, or

turn the system on, the lift unit moves down.

Conversely, listening to FM radio or turning the

system off moves the lift unit up. You can also operate

the lift unit manually by pressing .

x Direct input select buttons D

• TV: Switches the TV input select to either A-TV or

D-TV (whichever was selected last).

• DIGITAL: Switches the input select to digital

broadcast (D-TV).

• ANALOG: Switches the input select to analogue

broadcast (A-TV).

• DVD: Switches the input select to DVD.

• FM: Switches the input select to FM.

x Input select button A

Switches the input select. Each time you press the

button, the input select changes as below.

TV (A-TV or D-TV) t AV1 t AV2 t DVD t

AV4 t PC t HDMI t TV (A-TV or D-TV)

t........

Note

After pressing TV C, if you press the input select button A,

the input does not switch to AV1, but goes back to the

previous status before pressing TV C.

Lift unit

Using the remote

A

B

C

D

E

F

11

GB

x Auto input select button F

While the input is except DVD, if you press Z on the

system or H, the input will be changed to DVD

automatically.

This system has various types of menus:

• TV: TV MENU

• DVD: DVD MENU

DVD TOP MENU

DVD DISPLAY

• FM: FM MENU

These menus are available when either input is

selected.

• TV/DVD/FM: AMP MENU

x CURSOR MODE buttons B

When one of these buttons lights up, you can operate

its menu (</M/m/,/).

TV: Lights up when TV input is selected by TV (direct

input select button

D), or by pressing TV MENU.

DVD/FM: Lights up when DVD or FM is selected by

DVD, FM (direct input select button

D), or by

pressing DVD MENU.

If the </M/m/,/ buttons

E cannot be used,

press the CURSOR MODE button

B (if not lit), then

use </M/m/,/ buttons

E.

Notes

• The status shown by the CURSOR MODE buttons will

change to TV when you press these buttons below:

(Circled numbers refer to the remote illustration on

page 11).

4 – Previous channel

5 DIGITAL/ANALOG (direct input select)

6 Coloured buttons

– Digital text off

–

EPG (Digital Electronic Programme Guide)

– Favourite

/ – Text

qj – Picture Freeze

wa / – Info/Text reveal

• The status shown by the CURSOR MODE buttons will

change to DVD/FM when you press these buttons below:

(Circled numbers refer to the remote illustration on

page 11).

8 DVD DISPLAY

qd AMP MENU

FM MENU

qg PICTURE NAVI

ql DVD TOP MENU

Overview of the remote

Using the menu

1

2

3

4

5

6

7

8

9

0

qa

qs

qd

qf

qg

ws

wa

w;

ql

qk

qj

qh

With cover opened.

Continued

12

GB

1 / – Input select/Text hold

• In TV mode (page 25): Selects the input source

from equipment connected to the system.

• In Text mode (page 21): Holds the current page.

• In TV/DVD/FM mode (page 10): Switches the

input source.

– Lift up/down (page 71)

"/1 – On/standby (page 20)

Switches off the system temporarily. The 1

(standby) indicator on the system (front of the lift

unit) lights up. Press again to switch on the system

from the standby mode.

– Sleep timer (page 42)

3 Number buttons

• In TV mode: Selects channels. For channel

numbers 10 and above, enter the second digit

within two seconds.

• In Text mode: Enters the three digit page number

to select the page.

• In DVD mode: Selects the item, title, chapter,

etc. Enters the password and area code.

• In FM mode: Selects the preset number.

The number 5 button has a tactile dot.*

9 </M/m/,/ – Cursor, OK, ENTER (page 18)

qs % – Muting (page 20)

2 +/– – Volume +/–

qd DIMMER (page 69)

qh SOUND FIELD (page 28)

2 TV (CURSOR MODE) (page 11)

4 – Previous channel

Returns to the previous channel watched (for more

than five seconds).

5 DIGITAL/ANALOG (direct input select) (page 20)

6 Coloured buttons (page 22)

– Digital text off (page 21)

– EPG (Digital Electronic Programme Guide)

(page 22)

– Favourite (page 24)

/ – Text (page 21)

0 TV MENU (page 18)

qs PROG +/– (page 20)

The PROG + button has a tactile dot.*

qf – Picture Mode (page 38)

– Power Saving (page 41)

Reduces the power consumption of the system.

– Screen mode (page 21)

qj – Picture Freeze (page 21)

Freezes the TV picture.

wa / – Info/Text reveal

• In digital mode: Displays brief details of the

programme currently being watched.

• In analogue mode: Displays information such as

current channel number and screen mode.

• In Text mode (page 21): Reveals hidden

information (e.g., answers to a quiz).

ws TV (direct input select) (page 10)

2 DVD (CURSOR MODE) (page 11)

7 DVD MENU (page 49)

8 DVD DISPLAY (page 51)

qa ./> – Next/Previous +/– (page 30)

X – Pause (page 30)

H – Play (page 30)

The

H button has a tactile dot.*

, – Replay, Advance, Step

(page 30)

m/, M/ – Scan, Slow +/– (page 33)

x – Stop (page 30)

qd AMP MENU (page 70)

qg ANGLE (page 34)

AUDIO (page 31)

The AUDIO button has a tactile dot.*

PICTURE NAVI (page 33)

REPEAT (page 58)

SA-CD/CD (page 32)

SUBTITLE (page 34)

TIME/TEXT (page 54)

qk O RETURN (page 32)

ql DVD TOP MENU (page 49)

w; CLEAR (page 53)

ws DVD (direct input select) (page 10)

2 FM (CURSOR MODE) (page 11)

5 FM (direct input select) (page 10)

qa m/, M/ – Tuning (page 36)

qs PROG +/– (page 35)

The PROG + button has a tactile dot.*

qd FM MENU (page 36)

* Use the tactile dot as a reference when operating the system.

Common operations

To control the TV

To control the DVD

To control the FM tuner

13

GB

Overview of the system/

lift unit buttons and

indicators

Touch panel buttons (2 – 9): Touch any of these

buttons once, to activate the panel (buttons light up), then

touch the desired button.

1 Disc slot

2 Z – Eject

Eject a disc.

3 H – Play

Play a disc.

4 x – Stop

Stop a disc.

5 2 +/– – Volume

Increases (+)/decreases (–) volume.

6 PROG +/–

• In TV mode: Select next (+)/previous (–)

channel.

• In FM mode: Select next (+)/previous (–) preset

station.

7 FM

Change input select to FM directly.

8 TV

Change input select to TV directly.

9 – Input select

Select the input select of connected equipment.

Each time you press the button, the input select

changes as below.

A-TV t D-TV t AV1 t AV2 t DVD t

AV4 t PC t HDMI t A-TV t D-TV

t........

0 UP/DOWN – Lift unit up/down

Move the lift unit up/down.

qa 1 – Standby

Switch system on/off. While the system is on, if

you press "/1 on the remote, the system enters

standby mode.

qs ` – Power indicator

Lights green when system is on.

qd 1 – Standby indicator

Lights red when system is in standby mode.

qf – Picture Off (page 41)/Timer indicator

(page 42)

• Lights up in amber when the “Sleep Timer” is

set or when a digital event is programmed.

• Lights up in green when “Picture Off” is set.

• Lights up in red when digital REC starts.

qg Front panel display (page 69)

qh Sound Field indicator

qj – Remote control sensor

qk Lift unit

2CH STEREOAUTO

FRONT

SURROUND

TVTV

UP/DOWNUP/DOWN

FMFMPROGPROG

q

s

q

d

q

f

1

q

g

qk

q

j

q

h

0 q

a

8

42 653

79

14

GB

1: Checking the

accessories

Remote RM-ANU005 (1)

Size AA batteries (R6 type) (2)

AC power cord (mains lead) (1)

Screws (2)

FM wire antenna (aerial) (1)

Frame grille (1)

Quick Start Guide (1)

2: Inserting batteries

into the remote

Notes

• Observe the correct polarity when inserting batteries.

• Dispose of batteries in an environmentally friendly way.

Certain regions may regulate disposal of the battery.

Please consult your local authority.

• Do not use different types of batteries together or mix old

and new batteries.

• Handle the remote with care. Do not drop or step on it, or

spill liquid of any kind onto it.

• Do not place the remote in a location near a heat source, or

in a place subject to direct sunlight, or in a damp room.

Getting Started

15

GB

3: Connecting a TV aerial/VCR/DVD player

1 Remove the covers.

When all connections have been made, replace the

covers.

2 Connect your aerial to the socket on

the rear of the system.

If connecting to an aerial only

Go to step 4.

3 Connect your VCR/DVD player.

1 Connect the socket on the rear of the

system to the input socket on your VCR with

the RF lead.

2 Connect the scart socket on your VCR/DVD

player to the / 1 or 2 scart socket on

the rear of the system with a scart lead.

4 Connect the supplied AC power cord

(mains lead) to the AC IN socket on the

rear of the system.

Note

Do not connect the AC power cord (mains lead) to your

mains socket until all connections are complete.

To prevent the system from toppling over

Notes

• Be sure to take measures to prevent the system from

toppling over. If you fail to do so, the system may topple

over and cause injury. Anchor the system to a wall, pillar,

etc., to prevent it from toppling over.

• Any wall alternations (drilling, etc.) are your own

responsibility.

Prepare a commercially available strong rope or chain

and wall anchor bracket beforehand.

1 Remove the two small screws, and then

attach the two large screws to the screw

holes on the rear of the system.

(SmartLink)

12 5

PC

IN

OUT

Rear of the system

AC power cord

(mains lead)

(supplied)

Coaxial cable

(not supplied)

Scart lead (not supplied)

VCR

RF lead (not supplied)

Scart lead (not supplied)

DVD player

1

2

Continued

16

GB

2 Secure the wall anchor bracket to a wall

or pillar.

3 Thread the rope or chain through both

holes of the screws, and then tighten the

other end of the rope or chain to the wall

anchor bracket.

4: Connecting the FM

wire antenna (aerial)

Connect the supplied FM wire antenna (aerial) for

listening to the FM radio. Thread the wire antenna

(aerial) through the slit of the cover, and then replace

the cover.

Notes

• Be sure to fully extend the FM wire antenna (aerial).

• After connecting the FM wire antenna (aerial), keep it as

horizontal as possible.

A commercially

available wall

screw

A commercially available

strong rope or chain

DVD

DIGITAL OUT

FM ANTENNA

OPTICAL

FM 75

COAXIAL

FM wire antenna (aerial)

Getting Started

17

GB

Tip

If you have poor FM reception, use an “L” type 75-ohms

coaxial cable (not supplied) to connect the system to an

outdoor FM antenna (aerial) as shown below. If you use a 75-

ohms coaxial cable other than “L” type, you may not be able

to replace the covers properly.

5: Switching on the

system

Install this system so that the power cord can be

unplugged from the wall socket immediately in the

event of trouble.

1 Connect the system to your mains socket

(220-240V AC, 50Hz).

2 Press 1 on the system (top of the lift

unit).

When you switch on the system for the first time,

a message confirming the system start auto-tuning

appears on the screen, then go to “6: Auto-tuning

the TV” (page 18).

When the system is in standby mode (the 1

(standby) indicator on the system is red), press

+/1 on the remote to switch on the system.

Notes

• Depending on the Lift Mode setting or selected input,

the lift unit will move down when turning on the

system.

• To recall from standby mode by pressing 1 on the

system, press 1 to turn off the system, and then press

and hold 1 again until ` (power indicator) lights up in

green.

To save the power in standby mode

Press "/1 on the remote while the system turns on. To

cancel standby mode, press "/1 once.

DVD

DIGITAL OUT

FM ANTENNA

OPTICAL

FM 75

COAXIAL

Outdoor FM antenna

(aerial)

“L” type 75-ohms coaxial

cable (not supplied)

1

AC power cord

(mains lead)

Continued

18

GB

6: Auto-tuning the TV

After switching on the system, a message confirming

the system start auto-tuning appears on the screen.

You must tune the system to receive channels (TV

broadcasts). Do the following to search and store all

available channels.

1 Press (OK) to select [Yes].

The system starts searching for all available

digital channels, followed by all available

analogue channels. This may take some time,

please be patient and do not press any buttons on

the system or remote.

Once all available digital and analogue channels

have been stored, the system returns to normal

operation, displaying the digital channel stored on

channel number 1. If no digital channels are

found, the analogue channel stored on channel

number 1 is displayed.

When a message appears for you to confirm the

aerial connections

No digital or analogue channels are found. Check

all the aerial connections and press (OK) to

start auto-tuning again.

2 The Programme Sorting menu appears

on the screen.

Note

If some digital channel is found, this step will not

appear.

3 To change the order in which the

channels are stored on the system. See

page 44.

4 Press TV MENU to exit.

The system has now tuned in all the available

channels.

Hint

To stop Digital Auto Tuning, select [Cancel]. Digital

Auto Tuning is cancelled, and Analogue Auto Tuning

starts.

(OK)

TV MENU

Do you want to start

automatic tuning ?

Ye s No

m

Number of Services found 14

Searching. 40%

Cancel:

Digital auto-tune display

m

Auto Tuning

Programmes found:

5

Searching...

Analogue auto-tune display

Getting Started

19

GB

7: Selecting the DVD

language (Quick Setup)

You can set the display language.

1 Press DVD (direct input select) to switch

the input to DVD.

[Press [ENTER] to run QUICK SETUP.] appears

at the bottom of the screen. This message does not

appear if the disc is loaded or Quick Setup is

already done.

2 Press (ENTER) without inserting a

disc.

The Setup Display for selecting the language used

in the on-screen display appears.

3 Press M/m to select a language.

The system displays the on-screen display, the

menu and subtitles in the selected language.

Note

The selectable language is different depending on the

area.

4 Press (ENTER).

Quick Setup is finished. All connections and setup

operations are complete.

To quit the Quick Setup

Press DVD DISPLAY in any step.

To recall the Quick Setup display

1 Press DVD DISPLAY. (If a disc is playing, press x to

stop playback, then press DVD DISPLAY.)

The Control Menu appears.

2 Press M/m to select [SETUP], then press

(ENTER).

The options for [SETUP] appear.

3 Press M/m to select [QUICK], then press

(ENTER).

The Quick Setup display appears.

M/m/ (ENTER)

DVD

LANGUAGE SETUP

OSD:

MENU:

AUDIO:

SUBTITLE:

ITALIANO

ESPAÑOL

NEDERLANDS

DANSK

SVENSKA

FRANÇAIS

ENGLISH

DEUTSCH

1 2

(

2 7

)

QUICK

RESET

DVD VIDEO

: :

1 8

(

3 4

)

CUSTOM

QUICK

20

GB

Watching TV

1 Press 1 on the system to switch on the

system.

When the system is in standby mode (the 1

(standby) indicator on the system is red), press

"/1 on the remote to switch on the system.

2 Press DIGITAL to switch to digital mode

or ANALOG to switch to analogue mode.

The channels available vary depending on the

mode.

3 Press the number buttons or PROG

+/– to select a TV channel.

To select channel numbers 10 and above using the

number buttons, enter the second and third digits

within two seconds.

To select a digital channel using the Digital

Electronic Programme Guide (EPG), see page 22.

In digital mode

An information banner appears briefly. The

following icons may be indicated on the banner.

Additional operations

Watching TV

1

"/1

Number

buttons

DIGITAL

ANALOG

PROG +/–

: Interactive service is available (MHEG Digital

Text)

: Interactive service (MHEG Digital Text) is

currently disabled

: Radio service

: Scrambled/Subscription service

: Multiple audio languages available

: Subtitles available

: Subtitles available for the hearing impaired

: Recommended minimum age for current

programme (from 4 to 18 years)

: Parental Lock

: Current programme is being recorded

To Do this

Turn off the system

temporarily

(Standby mode)

Press "/1 on the remote.

Turn off the system

completely

Press 1 on the system.

Adjust the volume Press 2 + (increase)

/– (decrease).

Page is loading ...

Sony TAV-L1 Operating instructions

Sony TAV-L1 Operating instructions

Related papers

Other documents