MicroCore Upgrade Kit Installation Guide
Fixture: Universe Collection Medium (UCM) (HID to LED)
TM
www.aal.net
A R C H I T E C T U R A L A R E A L I G H T I N G
93046644 REV. D
PAGE 1/7
17760 ROWLAND ST. Tel(626)968-5666
CITY OF INDUSTRY Fax(626)968-5716
CALIFORNIA 91748
UPGRADE KIT CONTENTS
1
2
3
4
5
6
9
7
8
WARNING
: Fixtures must be grounded in accordance with local codes or the National Electrical Code. Failure to do so
may result in serious personal injury.
MAINTENANCE
: A regularly scheduled maintenance program should be established to retain optimum light
output and reduce heat retention. Dusting with a soft, clean, dry cloth is normally sufficient for the optics.
CAUTION
: All wiring must be done by a qualified electrician. KEEP THIS SHEET FOR FUTURE REFERENCE.
Examine all parts that are not intended to be replaced by the retrofit kit for damage, and replace any damaged parts
prior to installation of the unit.
!
10
11
ITEM # QTY PART # DESCRIPTION NOTE
1 1 - MICROCORE LED ARRAY
2 1 - DRIVER ASSEMBLY
3 1 93052784 RING HOOD UCM-32LED
93061495 BRKT-LENS FRM UCM-ANG-32LED FOR ANG/BEL/FLR HOOD
93061496 BRKT-LENS FRM UCM-STR-32LED FOR STR HOOD
93061497 BRKT-LENS FRM UCM-SKB-32LED FOR SKB HOOD
5 2 A84024 SCR-8-32x3/4 PHH PHMS SS
6 4 A84004 WSHR-1/4 INT TOOTH LK SS
7 4 A84051 SCR-1/4-20x1/2 BTN HD CAP SS
8 4 93030856 GSKT-ORING 3/8ODx3/16ID NPR
A84384 SCR-1/4-20x1.848 SKT BTN HD SS FOR ANG/STR HOOD
A84065 SCR-1/4-20x1 BTN HD CAP SS FOR FLR HOOD
93058975 SCR-1/4-20x3 SKT BTN HD SS FOR BEL/SKB HOOD
10 1 A56414-12 SPCR-3/8inODx .049in x5.058in FOR UPLIGHT ONLY
11 1 A84119 BOLT-1/4-20x6 HEX HD SS FOR UPLIGHT ONLY
4 4
9 4
MicroCore Upgrade Kit Installation Guide
Fixture: Universe Collection Medium (UCM) (HID to LED)
TM
www.aal.net
A R C H I T E C T U R A L A R E A L I G H T I N G
93046644 REV. D
PAGE 2/7
17760 ROWLAND ST. Tel(626)968-5666
CITY OF INDUSTRY Fax(626)968-5716
CALIFORNIA 91748
1.
REMOVE EXISTING REFLECTOR ASSEMBLY
TURN OFF ALL POWER TO
THE UNIT AND TAKE
PROPER SAFETY PRECAUTIONS.
FAILURE TO DO SO MAY RESULT
IN SERIOUS PERSONAL INJURY.
!
1. Open lower lens frame of the housing by
undoing (2) captive thumb screws located on
underside of fixture and swinging door frame
open as shown in Fig. 1-1 & Fig. 1-1A.
2. Allow door frame assembly to hang freely
as shown in Fig. 1-2
3. Remove existing reflector assembly by
prying housing from fixture. Existing reflector
assembly is held via ball socket studs as
shown in Fig. 1-3.
4.
Disconnect reflector assembly and set
aside as shown in Fig. 1-4
FIG. 1-1A
FIG. 1-1
FIG. 1-1A
FIG. 1-2
FIG. 1-3
FIG. 1-4
DOOR FRAME
ASSEMBLY
MicroCore Upgrade Kit Installation Guide
Fixture: Universe Collection Medium (UCM) (HID to LED)
TM
www.aal.net
A R C H I T E C T U R A L A R E A L I G H T I N G
93046644 REV. D
PAGE 3/7
17760 ROWLAND ST. Tel(626)968-5666
CITY OF INDUSTRY Fax(626)968-5716
CALIFORNIA 91748
2.
REMOVE EXISTING BALLAST ASSEMBLY
1. Locate locking pin on ballast
plate as shown in Fig. 2-1 & 2.1A.
2. Loosen locking pin by turning it
counter clockwise until stopped as
shown in Fig. 2-1A. Do not
disengage.
FIG. 2-1 FIG. 2-1A FIG. 2-2
3. Turn handle counter clockwise until range
of rotation stops as shown in Fig. 2-2 and
pull existing ballast assembly out.
4. Once removed, disconnect and discard
existing ballast into E-waste.
LOCKING PIN
HANDLE
3.
DISASSEMBLE DOME AND HOOD
1. Remove the hood by unscrewing (4)
1/4-20 hex bolts as shown in Fig. 3-1.
2. Save the hood, dome, (4) 1/4-20 hex
bolts and (4) washers for later use. Discard
everything else.
FIG. 3-1
FIG. 3-2
3. Detach the dome and hood as shown in
Fig. 3-2.
4X 1/4-20 HEX BOLTS
4X 1/4" WASHER
MicroCore Upgrade Kit Installation Guide
Fixture: Universe Collection Medium (UCM) (HID to LED)
TM
www.aal.net
A R C H I T E C T U R A L A R E A L I G H T I N G
93046644 REV. D
PAGE 4/7
17760 ROWLAND ST. Tel(626)968-5666
CITY OF INDUSTRY Fax(626)968-5716
CALIFORNIA 91748
4.
REMOVE TOP DOME RING
FIG. 4-1
FIG. 4-2
1. Remove top dome ring by unscrewing (2) 8-32 1/2in screws
as shown in Fig. 4-1 and discard the related hardware.
2. Peel off the existing gasket as shown in Fig. 4-2 and replace
with the new (provided) gasket.
2X 8-32 1/2" SCREWS
93046018
TOP DOME GASKET
ASSEMBLE HOOD AND RING
5.
1. Attach the hood to the dome by (4) provided Z-brackets, (4)
previously saved 1/4-20 hex bolts and washers as shown in
Fig. 5-1.
2. Assemble the hood ring by (4) provided 1/4-20 1/2" button
head screws and (4) washers as shown in Fig. 5-2.
4X HOOD BRACKETS
FIG. 5-1
FIG. 5-2
4X A84051
SCR-1/4-20x1/2 BTN HD CAP SS
4X A84004
WSHR-1/4 INT TOOTH LK SS
HOOD RING
TOP DOME RING
MicroCore Upgrade Kit Installation Guide
Fixture: Universe Collection Medium (UCM) (HID to LED)
TM
www.aal.net
A R C H I T E C T U R A L A R E A L I G H T I N G
93046644 REV. D
PAGE 5/7
17760 ROWLAND ST. Tel(626)968-5666
CITY OF INDUSTRY Fax(626)968-5716
CALIFORNIA 91748
7.
ASSEMBLE DRIVER ASSEMBLY
2. Connect green "C" to fixture ground lead "C" as shown in Fig.
7-2.
3.
Connect flying driver assembly green lead "D" to fixture
ground "D" as shown in Fig. 6-2.
A
C
CONNECTION TO
INCOMING POWER
BLACK
WHITE
GREEN (GROUND TO
BALLAST PLATE)
FIG. 6-1
FIG. 6-2
NOTE: SEE WIRING DIAGRAM
!
D
B
A
C
1. Connect incoming black "A" and incoming white "B" to driver
assembly black "A" and white "B" as shown in Fig. 6-1 & Fig.
6-2
Note: no change in grounding.
B
CONNECTION TO LED
MICROCORE
ASSEMBLY
6.
WIRE CONNECTIONS TO DRIVER ASSEMBLY
1. Assemble driver assembly to the dome by (2) provided 8-32
3/4" screws as shown in Fig 7-1.
FIG. 7-1
C
D
2X A84024
SCR-8-32x3/4 PHH PHMS SS
FIG. 5-3
B
A
C
C
D
NOTE: WITH UPLIGHT OPTIONS, REPLACE THE CURRENT
STANDOFFS BY PROVIDED ONES (AS SHOWN ABOVE) TO
ACCOMMODATE THE CHANGE IN HEIGHT OF NEW
COMPONENTS.
A84119
BOLT-1/4-20x6 HEX HD SS
A56414-12
SPCR-3/8inODx .049in x5.058in
MicroCore Upgrade Kit Installation Guide
Fixture: Universe Collection Medium (UCM) (HID to LED)
TM
www.aal.net
A R C H I T E C T U R A L A R E A L I G H T I N G
93046644 REV. D
PAGE 6/7
17760 ROWLAND ST. Tel(626)968-5666
CITY OF INDUSTRY Fax(626)968-5716
CALIFORNIA 91748
INSTALL MICROCORE ASSEMBLY
8.
STREET SIDE
FIG. 8-2
1. Determine street side and align optical array
direction accordingly. Look for light pattern label
(Fig. 8-1A) for LED direction.
FIG. 8-1
FIG. 8-1A
?
2. Connect MicroCore
assembly and driver
assembly as shown in Fig.
8-2.
FIG. 8-3
3. Drop the MicroCore deck
assembly into fixture housing
by aligning the safety brackets
and the cut out on hood ring as
shown in Fig. 8-2.
4. Rotate the MicroCore assembly clockwise until
stopped. At this time, the (4) mounting holes on
hood ring should line up with those on MicroCore
deck. The fixture is oriented properly to street side.
FIG. 8-3
4. Once everything is lined up, attach the MicroCore
assembly to the hood by (4) provided 1/4-20 button
head screws and (4) O-rings as shown in Fig. 8-4.
FIG. 8-4
4X A84065 / 84384 / 93058975
1/4-20 SOCKET SCREWS
4X 93030856
GSKT-ORING 3/8ODx3/16ID NPR
LENS FRAME ASSEBMLY
SHOWN AS REFERENCE
MicroCore Upgrade Kit Installation Guide
Fixture: Universe Collection Medium (UCM) (HID to LED)
TM
www.aal.net
A R C H I T E C T U R A L A R E A L I G H T I N G
93046644 REV. D
PAGE 7/7
17760 ROWLAND ST. Tel(626)968-5666
CITY OF INDUSTRY Fax(626)968-5716
CALIFORNIA 91748
UCM 32LED MICROCORE WIRING DIAGRAM
INCOMING POWER LEADS
THROUGH ARM
BOND TO FIXTURE
HOUSING
AT CAST DOME TOP
BLACK
WHITE
GREEN
GROUND TO
FIXTURE HOUSING
AT CAST DOME TOP
A
B
C
A
B
D
BLACK
WHITE
GREEN
D
C
MICROCORE LED ARRAY
DRIVER ASSEMBLY
/
