GB AWE 7516
5019 312 10543
Programme
Care
Labels
Max.
Load
kg
Type of wash / Notes
- for temperature selection, respect the manufacturer's recommendations on the care label
Detergents and Additives Special options Max.
Spin
Speed
rpm
Pre-
wash
Main
Wash
Softener Rapid Eco Pre-
wash
Start
delay
Intensive
rinse
Rinse
Hold
Variable
spin
Cotton
40 - 60 - 95 °C
40 - 60 - 95°C
5.0
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc.
made of cotton and linen.
For washing heavily soiled laundry, the “Prewash” option can be selected.
i
Yes
1)
i i
i
95°C
only
i i
2)
i i i
1000
Synthetics
30 - 40 - 60 °C
30 - 40 - 60°C
2.5
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira),
polyamide (Perlon, Nylon).
i
Yes
1)
i i
i
60°C
only
i i
2)
i i i
1000
Delicates
30 - 40 °C
30 - 40°C
1.5 Curtains and delicate clothing, dresses, skirts, shirts and blouses.
i
Yes
1)
i
– –
i i
2)
–
i i
1000
Daily Mixed
40 °C
40°C
3.0 Slightly to normally soiled textiles made of cotton and/or synthetics. – Yes
i
– – –
i
2)
i i i
1000
Quick wash
30 °C
30°C
3.0
Shortly worn outer clothing made of cotton, polyester, polyamide and blends with
cotton.
– Yes
i
– – –
i
2)
i i i
1000
Wool
Cold - 40 °C
- 40°C
1.0
Only woollens with a felt-free finish, labelled with the woolmark and identified as
machine washable.
– Yes
i
– – –
i
2)
–
i i
1000
Handwash
40 °C
40°C
1.0
Textiles made of linen, silk, wool and viscose marked as “handwashable”.
A very gentle spin is used in this programme.
– Yes
i
– – –
i
2)
–
i i
400
3)
Lingerie
30 °C
30°C
1.0
This cycle is particularly suitable to treat delicate lingerie (use of a laundry net strongly
recommended).
– Yes
i
– – –
i
2)
–
i i
400
3)
Rinse & Spin – 5.0 Same as the last rinse and the final spin in the “Cotton” programme. – –
i
– – –
i i i i
1000
Spin – 5.0 In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme. – – – – – –
i
– –
i
1000
Gentle Spin – 1.0 In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme. – – – – – –
i
– –
i
1000
Drain – – Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”. – – – – – –
i
– – – –
A. Programme selector
B. Time display
C. “Start delay” button
D. “Variable spin” button
E. “Start/Pause” button
F. Programme sequence indicator
G. “Reset” button
H. “Door open” indication
Whirlpool is a registered trademark of Whirlpool USA.
This washing machine is equipped with
automatic safety functions which detect and
diagnose faults at an early stage and react
appropriately:
I. “Service” indication
J. “Water tap closed” indication
K. “Clean pump” indication
1)
Do not use liquid detergent for main wash if you
have activated prewash option.
2)
Do not use liquid detergent.
3)
For improved garment care, spin speed is restricted
to 400 rpm in this programme.
PROGRAMME CHART
N.B. This machine is controlled by sensors. Please avoid excessive detergent dosing.
A
B
H
F
E
G
C
D
J
I
K
5019 312 10543
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration***
(hours : minutes)
Cotton 95 5.0 50* 1.70 2:05
Cotton** 60 5.0 45 0.85 2:30
Cotton 40 5.0 55 0.55 2:00
Synthetics 60 2.5 50* 0.80 1:30
Synthetics 40 2.5 45 0.45 1:15
Delicates 40 1.5 50 0.55 0:45
Daily Mixed 40 3.0 40 0.45 1:00
Quick wash 30 3.0 35 0.40 0:30
Wool 40 1.0 55 0.55 0:45
Handwash 40 1.0 40 0.40 0:35
Lingerie 30 1.0 40 0.30 0:35
CONSUMPTION DATA
Whirlpool is a registered trademark of Whirlpool USA.
1. Load the machine, close the drum doors and check
that they are properly locked.
2. Add detergent and additives into the dispenser to
no more than the “MAX” level mark, as follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softeners and conditioners
• Stain remover agents
• Anti-scale agents (if necessary)
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The time display
shows the duration of the chosen programme (in
hours and minutes), and the lamp next to the “Start
Pause” button flashes. The indication lamp of the
predefined spin speed lights up.
Prewash cycle increases programme duration by aproximately 20 min. Consumption values were measured in normalized conditions in
compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to
the water supply pressure and temperature, the load and the type of wash.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water
out.
** Reference Programme for Energy Label.
*** The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions
applicable at that time.
PREPARATION OF THE WASH CYCLE
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a
wash programme is running, the lid remains locked and
must on no account be forced open. In case you have
an urgent need to open it during a running programme,
refer to “Cancel (Reset) a running programme before
the end”.
RED INDICATIONS
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for Use”;
if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap: if the indications still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned: in the
latter case refer to the Instructions for Use (“Removing
the Filter”).
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 20 min.
“Intensive Rinse” button
• The amount of water is increased to ensure a more
intensive rinse.
• This option is particularly suitable for areas with very
soft water, washing baby linen and people with skin
allergies.
“Rinse Hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• This option is particularly recommended for the
“Synthetics”, “Daily load” and “Delicates”
programmes.
• It is useful if you want to postpone spinning to a later
time, or if you want to drain out only.
• If you select “Rinse Hold”, do not leave items to
soak for too long.
• As soon as the appliance stops in the rinse hold, the
“Anticrease” lamp of the sequence indicator lights up
and the lamp next to the “Start/Pause” button flashes.
Terminate the “Rinse Hold” option:
• Press the “Start/Pause” button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain”
programme and press the “Start/Pause” button.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause” button
lights up. The programme sequence indicator shows
the current programme phase, running from left to right
through Wash, Rinse, Spin/Drain. When the programme
phrase is finised, the corresponding indication goes out.
• Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
PROGRAMME END
• All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the
interior of the machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Select the new programme, any options and another
spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the
end. Press the “Reset” button for at least 3 seconds.
Any existing water is drained out before the door can be
opened.
SELECT THE DESIRED OPTION(S)
Selecting or deselecting an option can be done at
any time during the programme. The option will be
applied as long as the corresponding programme
phase has not been executed yet.
“Rapid” button
• Reduces water consumption, above all during rinsing.
• Suitable for lightly soiled laundry and small loads
(max. 3 kg).
“Eco” button
• With a modified temperature profile and a slightly
prologned washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
• Selectable for programmes Cotton 95°C and
Synthetics 60°C only.
START DELAY
The “Start delay” button allows the user to run the
machine at his convenience, for example at night when
electricity is cheaper.
• Select programme, spin speed and options.
• Press the “Start Delay” button several times to
select a delay time by 1 to 23 hours.
• Start the programme (see “Progremme Start”).
The indication lamp over the “Start delay” button
lights up and goes off when the programme starts.
• Once having pressed the “Start/Pause” button,
the countdown of the time delay begins. The time
delay indication on the display disappears when the
programme starts and is replaced by the remaining time.
• After the “Start/Pause” button has been pressed,
the number of hours preselected can be reduced by
pressing again the “Start delay” button.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to another position
or press the “Reset” button.
..after having pressed the “Start/Pause” button:
• Press the “Reset” button for at least 3 second. The
start delay indicator light goes off.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
the rinse. The water is drained out only.
/