5019 612 10191
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx.Programme
Duration***
(hours:minutes)
Cotton 95 5.0 50* 1.70 2:05
Cotton** 60 5.0 45 0.85 2:30
Cotton 40 5.0 55 0.55 2:00
Synthetics 60 2.5 50* 0.80 1:30
Synthetics 40 2.5 45 0.45 1:15
Delicates 40 1.5 50 0.55 0:45
Dailyload 40 3.0 40 0.45 1:00
Quickwash 30 3.0 35 0.40 0:30
Wool 40 1.0 55 0.55 0:45
Handwash 40 1.0 40 0.40 0:35
Handwash 30 1.0 40 0.30 0:31
Prewashcycleincreasesprogrammedurationbyaproximately20min.Consumptionvaluesweremeasuredinnormalizedconditionsin
compliancewithstandardIEC/EN60456.Consumptiondatainthehomemayvarywithrespecttothevaluesinthetableinrelationto
thewatersupplypressureandtemperature,theloadandthetypeofwash.
* Toreducethewatertemperature,somecoldwaterisaddedattheendofthemainwashcycle,beforethepumpdrainsthewater
out.
** ReferenceProgrammeforEnergyLabel.
*** Theremainingtimeindicatorcandeviatefromthevaluesinthetable,becauseittakesintoaccountthehouseholdconditions
applicableatthattime.
1. Loadthemachine,closethedrumdoorsandcheck
thattheyareproperlylocked.
2. Adddetergentasindicatedonthefrontpageandas
describedinthechapter“DetergentandAdditives”
inyourInstructionforUse,andclosethelid.
3. Turntheprogramme selectortothedesired
programmeandtemperature.Thetimedisplay
showsthedurationofthechosenprogramme(in
hoursandminutes),andthelampnexttothe
“Start”buttonflashes.Theindicationlampofthe
predefinedspinspeedlightsup.
4. Thespin speedindicatedcanbealteredbypressing
the“Variablespin”button.
PREPARATION OF THE WASH CYCLE
“Prewash” button
• Onlyforheavilysoiledloads(forexamplesand,
granulardirt)sensible.Increasesthecycletimeby
approximately20min.
• Donotuseliquiddetergentforthemainwashwhen
activatingtheprewashoption.
“Intensive rinse” button
• Theamountofwaterisincreasedtoensureamore
intensiverinse.
• Thisoptionisparticularlysuitableforareaswithvery
softwater,washingbabylinenandpeoplewithskin
allergies.
“Rinse hold” button
• Thelaundryremainsinthelastrinsewaterwithout
progressingtothefinalspincycletoavoidcreasing
andpreventcoloursfromchanging.
• Thisoptionisparticularlyrecommendedforthe
“Synthetics”,“Dailyload”and“Delicates”
programmes.
• Itisusefulifyouwanttopostponespinningtoalater
time,orifyouwanttodrainoutonly.
• Ifyouselect“Rinsehold”,donotleaveitemsto
soakfortoolong.
• Assoonastheappliancestopsintherinsehold,the
“Rinsehold”lampofthesequenceindicatorlightsup
andthelampnexttothe“Start”buttonflashes.
Terminate the “Rinse hold” option:
• Pressthe“Start”button;theprogramme
willterminateautomaticallywiththefinalspincycle
forthepresentwashprogramme.
• Ifyoudonotwishtospintheclothes,turnthe
programmeselectorknobtothe“Drain”
programmeandpressthe“Start”button.
“Variable spin” button
• Everyprogrammehasapredefinedspinspeed.
• Pressthebuttontosetanotherspinspeed.
• Ifspinspeed“0”isselected,thefinalspinningis
cancelledbutintermediatespinpeaksremainduring
therinse.Thewaterisdrainedoutonly.
SELECT THE DESIRED OPTION(S)
Selecting or deselecting an option can be done at
any time during the programme. The option will be
applied as long as the corresponding programme
phase has not been executed yet.
“Cold wash” button
• Waterisheatedonlyupto20ºC.
• Suitablefordelicatelaundryitemswithwash
temperaturerecommendationofmax.30ºConthe
carelabel.
• Selectable only on the lowest temperature step
of each programme.
“Eco” button
• Withamodifiedtemperatureprofileandaslightly
prolognedwashingduration,theoptimum
combinationofexcellentwashingresultandeven
lowerenergyconsumptionisachieved.
• SelectableforprogrammesCotton95ºCand
Synthetics60ºC.
“DOOR OPEN” INDICATION
Beforestartingandafterendofaprogramme,thelamp
lightstoshowthethelidcanbeopened.Aslongasa
washprogrammeisrunning,thelidremainslockedand
mustonnoaccountbeforcedopen.Incaseyouhave
anurgentneedtoopenitduringarunningprogramme,
referto“Cancel(Reset)arunningprogrammebefore
theend”.
RED INDICATIONS
“Service”
Lightingupofthe“Service”indicationcanbecaused
byafaultinanelectricalcomponent.Refertothe
“TroubleshootingGuide”inyour“InstructionsforUse”;
ifthefaultpersists,contactourAfterSalesService.
“Water tap closed”
Theappliancehasnoorinsufficientwatersupply.Open
thewatertap:iftheindicationsstilllightsup,refertothe
“TroubleshootingGuide”intheInstructionsforUse.
“Clean pump”
Wastewaterisnotpumpedout.Checkwhetherthe
drainhoseiskinkedorthefiltermustbecleaned:inthe
lattercaserefertotheInstructionsforUse(“Removing
theFilter”).
PROGRAMME START
Openthetapandpressthe“Start” button.The
indicationlampnexttothe“Start” buttonlightsup.
Theprogrammesequenceindicatorshowsthecurrent
programmephase,runningfromlefttorightthrough
Wash,Rinse,Spin/Drain.Whentheprogrammephraseis
finised,thecorrespondingindicationgoesout.
• Note: Ifthereisapowerinterruptionorifthe
applianceisdisconnectedduringthecycle,the
programmewillrunagainfromthepointwhereit
wasinterrupted.
PROGRAMME END
• Allthelightsoftheprogrammesequenceindicator
areoff,andthe“Dooropen”indicationlightsup.
1. Turntheprogrammeselectortothe“Off/O”
position.
2. Closethewatertap.
3. Openlidanddrumandunloadthemachine.
4. Leavethelidopenforsometimetoallowthe
interiorofthemachinetodry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Pressthe“Start” buttontopausethe
programme.Thelightflashes.
2. Selectthenewprogramme,anyoptionsandanother
spinspeedifyouwant.
3. Pressthe“Start” buttonagain.Thenew
programmecontinuesatthesamepositionwhere
thepreviousprogrammewasinterrupted.Donot
adddetergentforthisprogramme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The“Reset”buttoncancelsaprogrammebeforethe
end.Pressthe“Reset” buttonforatleast3seconds.
Anyexistingwaterisdrainedoutbeforethelidcanbe
opened.
START DELAY
The“Startdelay”buttonallowstheusertorunthe
machineathisconvenience,forexampleatnightwhen
electricityischeaper.
• Selectprogramme,spinspeedandoptions.
• Pressthe“Startdelay”buttonseveraltimesto
selectadelaytimeby1to23hours.
• Starttheprogramme(see“ProgremmeStart”).
Theindicationlampoverthe“Startdelay”button
lightsupandgoesoffwhentheprogrammestarts.
• Oncehavingpressedthe“Start”button,
thecountdownofthetimedelaybegins.Thetime
delayindicationonthedisplaydisappearswhenthe
programmestartsandisreplacedbytheremainingtime.
• Afterthe“Start”buttonhasbeenpressed,
thenumberofhourspreselectedcanbereducedby
pressingagainthe“Startdelay”button.
To cancel the “Start delay”
..before you press the “Start” button:
• Turntheprogrammeselectortoanotherposition
orpressthe“Reset”button.
..after having pressed the “Start” button:
• Pressthe“Reset”buttonforatleast3second.The
startdelayindicatorlightgoesoff.