Southern Enterprises MS333400TX Assembly Instructions Manual

Brand: Southern Enterprises

Model: MS333400TX

Type: Assembly Instructions Manual

This manual is also suitable for

LADDER MEDIA STAND

For assistance with assembly contact:

Southern Enterprises Inc.

Customer Service 1-800-633-5096

service@seidal.com

www.seidal.com

MS333400TX –ESPRESSO

LADDER MEDIA STAND

Assembly Instructions

PO#12877

Quantity

of 1

Bottom Panel

Quantity

Of 1

Left Side Panel

Quantity

of 1

Right Side Panel

Quantity

Of 1

Top Center Panel

Quantity

of 1

Bottom Center Panel

Quantity

Of 1

Back Panel

Quantity

of 1

Bottom Left Post

Quantity

Of 1

Bottom Right Post

Quantity

of 1

Top Right Post

Quantity

of 1

Top Panel

Quantity

Of 1

Shelf Panel

LADDER MEDIA STAND

Parts List

Please review all parts and hardware before disposing of any packaging.

Call Customer Service if missing hardware.

Using a screw that is too long will cause damage.

Before beginning assembly, separate each type of screw. Carefully study the

screw diagrams below. You may receive extra hardware with your unit.

Drawer Back Panel

Quantity

of 2

Drawer Bottom Panel

Quantity

of 2

Middle Leg

Quantity

of 1

Bottom Shelf Panel

Quantity

of 1

Drawer Front

Quantity

of 2

Drawer Left Side Panel

Quantity

of 2

Drawer Right Side Panel

Quantity

of 2

Top Shelf Panel

Quantity

of 1

Medium Shelf Panel

Quantity

of 1

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

Quantity

of 20

Cam Bolt

Quantity

Of 20

Cam Lock

Quantity

of 36

Quantity

Of 4

Φ8mm*1”

Wood Dowel

Φ8mm*1-3/16”

Wood Dowel

Quantity

of 10

Φ1/4”*1”

Hexagon Head Bolt

Quantity

Of 10

Spring Washer

Quantity

of 10

Flat Washer

Quantity

Of 1

Allen Wrench

Quantity

of 2

Quantity

Of 4

Cross Socket Nut

Quantity

of 16

Φ9*Φ4mm*1”

Screw

Quantity

Of 16

Φ6mm*1-3/16”

Wood Dowel

Quantity

of 2

Knob

Quantity

of 4

Φ9*Φ4mm*3/4”

Bolt

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

(23)

Care and Cleaning Instructions:

Before using, wipe with a clean, dry cloth.

Periodically apply furniture wax to renew

the finish . Avoid rubbing or scratching the

surface with rough or abrasive objects.

For replacement parts or questions, please

call Customer Service at 1-800-633-5096.

Please call manufacturer for assistance,

questions or parts.

Assembly Tool Required

No.2 Phillips Screwdriver (Not Included)

Tool List: 3/16" drill bit, drill, tape measure and pencil.

Quantity

of 12

Angle Iron

Quantity

of 36

Φ8*Φ4mm*7/16”

Screw

Quantity

of 6

Wooden Plug

Quantity

of 24

Sticker

Quantity

of 4

Anti-Tip Iron

Quantity

of 2

Plastic Strip

Quantity

of 2

Quantity

of 2

Plastic Anchor

Φ8*Φ4mm*9/16”

Short Screw

Quantity

of 2

Φ8*Φ4mm*1”

Long Screw

Insert cam lock (2) into pre-drilled holes

on top center panel (F).

Screw cam bolt (1) into pre-drilled holes on

shelf panel (B).

Attach top center panel (F) to shelf panel

(B) by inserting wood dowel (3) & cam bolt

(1) into corresponding pre-drilled holes

until top center panel (F) to shelf panel (B)

meet.

Secure by rotating cam lock (2) clockwise

with Phillips Screwdriver.

Cover cam lock (2) with sticker (17).

Insert cam lock (2) into pre-drilled holes

on bottom center panel (G).

Screw cam bolt (1) into pre-drilled holes on

shelf panel (B).

Attach bottom center panel (G) to shelf

panel (B) by inserting wood dowel (3) &

cam bolt (1) into corresponding pre-drilled

holes until bottom center panel (G) to shelf

panel (B) meet.

Secure by rotating cam lock (2) clockwise

with Phillips Screwdriver.

Cover cam lock (2) with sticker (17).

Insert cam lock (2) into pre-drilled holes

on pre-assembled unit in figure 2.

Screw cam bolt (1) into pre-drilled holes on

shelf panel (B).

Attach right side panel (E) &left side panel

(D) to shelf panel (B) by inserting wood

dowel (3) & cam bolt (1) into

corresponding pre-drilled holes until right

side panel (E) &left side panel (D) to shelf

panel (B) meet.

Secure by rotating cam lock (2) clockwise

with Phillips Screwdriver.

Cover cam lock (2) with sticker (17).

LADDER MEDIA STAND

Assembly Instructions

Figure 1

( 2)

( 1)

"Please do not over tighten cam bolts.

Please stop when you feel tight"

Figure 2

Figure 3

Insert cam lock (2) into pre-drilled holes

on pre-assembled unit in figure 3.

Screw cam bolt (1) into pre-drilled holes on

top panel (A).

Attach top panel (A) to right side panel

(E) ,top center panel (F) and left side panel

(D) by inserting wood dowel (3) & cam bolt

(1) into corresponding pre-drilled holes

until top panel (A) to right side panel

(E) ,top center panel (F) and left side panel

(D) meet.

Secure by rotating cam lock (2) clockwise

with Phillips Screwdriver.

Cover cam lock (2) with sticker (17).

Insert back panel (H) into left side panel

(D) and right side panel (E).

Insert cam lock (2) into pre-drilled holes

on pre-assembled unit in figure 5.

Screw cam bolt (1) into pre-drilled holes on

bottom panel (C).

Attach bottom panel (C) to right side panel

(E) ,to bottom center panel (G) and left

side panel (D) by inserting wood dowel (3)

& cam bolt (1) into corresponding

pre-drilled holes until bottom panel (C) to

right side panel (E) ,to bottom center panel

(G) and left side panel (D) meet.

Secure by rotating cam lock (2) clockwise

with Phillips Screwdriver.

Cover cam lock (2) with sticker (17).

Figure 4

Figure 5

Figure 6

Attach bottom left post (I) to left side panel

(D) by using hexagon head bolt (5) ,spring

washer (6) and flat washer (7). Tighten

with Allen wrench (8) .

Cover hexagon head bolt (5) with sticker

(17).

Attach bottom right post (J) to right side

panel (E) by using hexagon head bolt

(5) ,spring washer (6) and flat washer (7) .

Tighten with Allen wrench (8) .

Cover hexagon head bolt (5) with sticker

(17).

Screw middle leg (U) to bottom panel (C)

Attach top left post (K) to top shelf panel

(M), medium shelf panel (N) and bottom

shelf panel (O) by using hexagon head bolt

(5) ,spring washer (6) and flat washer (7) .

Tighten with Allen wrench (8) .

Cover hexagon head bolt (5) with wooden

plug (18).

Figure 7

Figure 8

Figure 9

Attach top right post (L) to top shelf panel

(M), medium shelf panel (N) and bottom

shelf panel (O) by using hexagon head bolt

(5) ,spring washer (6) and flat washer (7) .

Tighten with Allen wrench (8) .

Cover hexagon head bolt (5) with wooden

plug (18).

Attach top right post (L) to bottom right

post (J) ,and attach top left post (K) to

bottom left post (I) by using wood dowel

(3) ,Pin(9) and cross socket nut (10)

Attach 12pcs angle iron (15) to the edge of

top post and each shelf panel in figure 12,

tight angle iron (15) with screw (16) by

screw driver.

Figure 11

Figure 12

Figure 10

Join drawer front (P) to drawer left side

panel (Q) by using wood dowel (12) and

screw (11), tighten by screw driver.

Join drawer back panel (S) to drawer left

side panel (Q) by using wood dowel (12)

and screw (11), tighten by screw driver.

Insert bottom panel (T) to drawer front (P)

and drawer back panel (S).

Join drawer right side panel (R) to drawer

front (P) and drawer back panel (S) by

using wood dowel (12) and screw (11),

tighten by screw driver.

Attach knob (13) to drawer front (P) with

bolt (14) tighten by screw driver.

Repeat step 1-5 assembly for other drawer

Slide two drawers into the assembled part

onto the pre-fitted metal slide.

Figure 13

Figure 14

Attach anti-tip iron (19) to the back of top

panel (A) with short screw (21). Tighten

with screw driver.

Mark two desired locations on wall. Drill

two 3/16" holes on wall. Insert plastic

anchors (22) into the 2 holes on wall as

shown. (When doing this, you will need a

hammer help you).

Attach the anti-

tip iron (19) to wall using

long screw (23).Tight long screw (23) with

Philip screw driver.

Move this item close to the wall anti-tip

(19) and tie in both anti-tip (19) with

plastic strip (20) as shown in figure 15.

Anti-tipping hardware must be used

on this product to avoid tipping risk

and injury.

Now your LADDER MEDIA STAND is ready

to use.

Figure 15

Please immediately examine this product carefully. Any request for missing parts or damage

replacement must be received within 90 days of your receipt of the product. Replacement, if

available, will be honored within this time frame. Parts will not be available for items arriving fully

assembled. We do not recommend modifying product(s) and we are not responsible for any

damages due to product modification(s).

If damages or missing parts are not reported within 90

days of your receipt, we are under no obligation to provide parts or replacement merchandise.

Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm

Mon-Fri Central time if you have product issues or email us at service@seidal.com. Please ask for

customer service representative for issues involving damages or replacement parts. Please ask for

technical assistance representative for any issues with product and assembly/construction.

Please contact the retailer that you purchased from for returns.

Customer Information

Name

Address

City/State/Zip Code

Phone Number

Please indicate where you purchased this item: Store/Website/Catalog

Please indicate color/size/style number:

Style No Parts Letter Parts Description Quantity Needed

Parts Replacement Form

Customer Service 1-800-633-5096

[email protected]om

Southern Enterprises, Inc.

600 Freeport Parkway, Suite 200

Coppell, Texas 75019

CAUTION

The top shelf is intended for a flat screen television with a maximum overall width

of 40” and supports up to 80 lb.

The top shelf is NOT INTENDED for tube televisions.

Each shelf should not be loaded with more than 25 lb.

DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the

maximum sizes and weights indicated may result in instability causing possible

injury.

This unit contains a permanent warning sticker located on under side of top shelf

or inside drawer.

Do not allow children under 16 years to move the cart.

Model: MS333400TX

Ladder Media Stand

Southern Enterprises, Inc

600 Freeport Parkway,

Suite 200 Coppell, Texas, 75019

Manufacture Date: 01/15/2014

Southern Enterprises MS333400TX Assembly Instructions Manual

Brand: Southern Enterprises

Model: MS333400TX

Type: Assembly Instructions Manual

This manual is also suitable for

LADDER MEDIA STAND

Download PDF

report

Southern Enterprises MS333400TX Assembly Instructions Manual

This manual is also suitable for

Southern Enterprises MS333400TX Assembly Instructions Manual

Related papers

Other documents