Southern Enterprises LADDER MEDIA STAND Assembly Instructions Manual

Southern Enterprises
Brand
Southern Enterprises
Model
LADDER MEDIA STAND
Type
Assembly Instructions Manual

This manual is also suitable for

For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
service@seidal.com
www.seidal.com
MS333400TX –ESPRESSO
LADDER MEDIA STAND
Assembly Instructions
PO#12877
A
B
C
D
E
F
G
H
I
J
K
L
Quantity
of 1
Bottom Panel
Quantity
Of 1
Left Side Panel
Quantity
of 1
Right Side Panel
Quantity
Of 1
Top Center Panel
Quantity
of 1
Bottom Center Panel
Quantity
Of 1
Back Panel
Quantity
of 1
Bottom Left Post
Quantity
Of 1
Bottom Right Post
Quantity
of 1
Top Left Post
Quantity
Of 1
Top Right Post
Quantity
of 1
Top Panel
Quantity
Of 1
Shelf Panel
LADDER MEDIA STAND
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study the
screw diagrams below. You may receive extra hardware with your unit.
M
N
O
P
Q
R
S
T
U
Drawer Back Panel
Quantity
of 2
Drawer Bottom Panel
Quantity
of 2
Middle Leg
Quantity
of 1
Bottom Shelf Panel
Quantity
of 1
Drawer Front
Quantity
of 2
Drawer Left Side Panel
Quantity
of 2
Drawer Right Side Panel
Quantity
of 2
Top Shelf Panel
Quantity
of 1
Medium Shelf Panel
Quantity
of 1
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
Quantity
of 20
Cam Bolt
Quantity
Of 20
Cam Lock
Quantity
of 36
Quantity
Of 4
Φ8mm*1”
Wood Dowel
Φ8mm*1-3/16”
Wood Dowel
Quantity
of 10
Φ1/4”*1”
Hexagon Head Bolt
Quantity
Of 10
Spring Washer
Quantity
of 10
Flat Washer
Quantity
Of 1
Allen Wrench
Quantity
of 2
Pin
Quantity
Of 4
Cross Socket Nut
Quantity
of 16
Φ9*Φ4mm*1”
Screw
Quantity
Of 16
Φ6mm*1-3/16”
Wood Dowel
Quantity
of 2
Knob
Quantity
of 4
Φ9*Φ4mm*3/4”
Bolt
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish . Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call Customer Service at 1-800-633-5096.
Please call manufacturer for assistance,
questions or parts.
Assembly Tool Required
No.2 Phillips Screwdriver (Not Included)
Tool List: 3/16" drill bit, drill, tape measure and pencil.
Quantity
of 12
Angle Iron
Quantity
of 36
Φ8*Φ4mm*7/16”
Screw
Quantity
of 6
Wooden Plug
Quantity
of 24
Sticker
Quantity
of 4
Anti-Tip Iron
Quantity
of 2
Plastic Strip
Quantity
of 2
Quantity
of 2
Plastic Anchor
Φ8*Φ4mm*9/16”
Short Screw
Quantity
of 2
Φ8*Φ4mm*1”
Long Screw
Insert cam lock (2) into pre-drilled holes
on top center panel (F).
Screw cam bolt (1) into pre-drilled holes on
shelf panel (B).
Attach top center panel (F) to shelf panel
(B) by inserting wood dowel (3) & cam bolt
(1) into corresponding pre-drilled holes
until top center panel (F) to shelf panel (B)
meet.
Secure by rotating cam lock (2) clockwise
with Phillips Screwdriver.
Cover cam lock (2) with sticker (17).
Insert cam lock (2) into pre-drilled holes
on bottom center panel (G).
Screw cam bolt (1) into pre-drilled holes on
shelf panel (B).
Attach bottom center panel (G) to shelf
panel (B) by inserting wood dowel (3) &
cam bolt (1) into corresponding pre-drilled
holes until bottom center panel (G) to shelf
panel (B) meet.
Secure by rotating cam lock (2) clockwise
with Phillips Screwdriver.
Cover cam lock (2) with sticker (17).
Insert cam lock (2) into pre-drilled holes
on pre-assembled unit in figure 2.
Screw cam bolt (1) into pre-drilled holes on
shelf panel (B).
Attach right side panel (E) &left side panel
(D) to shelf panel (B) by inserting wood
dowel (3) & cam bolt (1) into
corresponding pre-drilled holes until right
side panel (E) &left side panel (D) to shelf
panel (B) meet.
Secure by rotating cam lock (2) clockwise
with Phillips Screwdriver.
Cover cam lock (2) with sticker (17).
LADDER MEDIA STAND
Assembly Instructions
Figure 1
( 2)
( 1)
"Please do not over tighten cam bolts.
Please stop when you feel tight"
Figure 2
Figure 3
Insert cam lock (2) into pre-drilled holes
on pre-assembled unit in figure 3.
Screw cam bolt (1) into pre-drilled holes on
top panel (A).
Attach top panel (A) to right side panel
(E) ,top center panel (F) and left side panel
(D) by inserting wood dowel (3) & cam bolt
(1) into corresponding pre-drilled holes
until top panel (A) to right side panel
(E) ,top center panel (F) and left side panel
(D) meet.
Secure by rotating cam lock (2) clockwise
with Phillips Screwdriver.
Cover cam lock (2) with sticker (17).
Insert back panel (H) into left side panel
(D) and right side panel (E).
Insert cam lock (2) into pre-drilled holes
on pre-assembled unit in figure 5.
Screw cam bolt (1) into pre-drilled holes on
bottom panel (C).
Attach bottom panel (C) to right side panel
(E) ,to bottom center panel (G) and left
side panel (D) by inserting wood dowel (3)
& cam bolt (1) into corresponding
pre-drilled holes until bottom panel (C) to
right side panel (E) ,to bottom center panel
(G) and left side panel (D) meet.
Secure by rotating cam lock (2) clockwise
with Phillips Screwdriver.
Cover cam lock (2) with sticker (17).
Figure 4
Figure 5
Figure 6
Attach bottom left post (I) to left side panel
(D) by using hexagon head bolt (5) ,spring
washer (6) and flat washer (7). Tighten
with Allen wrench (8) .
Cover hexagon head bolt (5) with sticker
(17).
Attach bottom right post (J) to right side
panel (E) by using hexagon head bolt
(5) ,spring washer (6) and flat washer (7) .
Tighten with Allen wrench (8) .
Cover hexagon head bolt (5) with sticker
(17).
Screw middle leg (U) to bottom panel (C)
.
Attach top left post (K) to top shelf panel
(M), medium shelf panel (N) and bottom
shelf panel (O) by using hexagon head bolt
(5) ,spring washer (6) and flat washer (7) .
Tighten with Allen wrench (8) .
Cover hexagon head bolt (5) with wooden
plug (18).
Figure 7
C
E
D
D
E
Figure 8
Figure 9
Attach top right post (L) to top shelf panel
(M), medium shelf panel (N) and bottom
shelf panel (O) by using hexagon head bolt
(5) ,spring washer (6) and flat washer (7) .
Tighten with Allen wrench (8) .
Cover hexagon head bolt (5) with wooden
plug (18).
Attach top right post (L) to bottom right
post (J) ,and attach top left post (K) to
bottom left post (I) by using wood dowel
(3) ,Pin(9) and cross socket nut (10)
Attach 12pcs angle iron (15) to the edge of
top post and each shelf panel in figure 12,
tight angle iron (15) with screw (16) by
screw driver.
Figure 11
Figure 12
Figure 10
Join drawer front (P) to drawer left side
panel (Q) by using wood dowel (12) and
screw (11), tighten by screw driver.
Join drawer back panel (S) to drawer left
side panel (Q) by using wood dowel (12)
and screw (11), tighten by screw driver.
Insert bottom panel (T) to drawer front (P)
and drawer back panel (S).
Join drawer right side panel (R) to drawer
front (P) and drawer back panel (S) by
using wood dowel (12) and screw (11),
tighten by screw driver.
Attach knob (13) to drawer front (P) with
bolt (14) tighten by screw driver.
Repeat step 1-5 assembly for other drawer
Slide two drawers into the assembled part
onto the pre-fitted metal slide.
Figure 13
Figure 14
Attach anti-tip iron (19) to the back of top
panel (A) with short screw (21). Tighten
with screw driver.
Mark two desired locations on wall. Drill
two 3/16" holes on wall. Insert plastic
anchors (22) into the 2 holes on wall as
shown. (When doing this, you will need a
hammer help you).
Attach the anti-
tip iron (19) to wall using
long screw (23).Tight long screw (23) with
Philip screw driver.
Move this item close to the wall anti-tip
(19) and tie in both anti-tip (19) with
plastic strip (20) as shown in figure 15.
Anti-tipping hardware must be used
on this product to avoid tipping risk
and injury.
Now your LADDER MEDIA STAND is ready
to use.
Figure 15
Please immediately examine this product carefully. Any request for missing parts or damage
replacement must be received within 90 days of your receipt of the product. Replacement, if
available, will be honored within this time frame. Parts will not be available for items arriving fully
assembled. We do not recommend modifying product(s) and we are not responsible for any
damages due to product modification(s).
If damages or missing parts are not reported within 90
days of your receipt, we are under no obligation to provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm
Mon-Fri Central time if you have product issues or email us at service@seidal.com. Please ask for
customer service representative for issues involving damages or replacement parts. Please ask for
technical assistance representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
CAUTION
The top shelf is intended for a flat screen television with a maximum overall width
of 40” and supports up to 80 lb.
The top shelf is NOT INTENDED for tube televisions.
Each shelf should not be loaded with more than 25 lb.
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the
maximum sizes and weights indicated may result in instability causing possible
injury.
This unit contains a permanent warning sticker located on under side of top shelf
or inside drawer.
Do not allow children under 16 years to move the cart.
Model: MS333400TX
Ladder Media Stand
Southern Enterprises, Inc
600 Freeport Parkway,
Suite 200 Coppell, Texas, 75019
Manufacture Date: 01/15/2014
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Southern Enterprises LADDER MEDIA STAND Assembly Instructions Manual

Southern Enterprises
Brand
Southern Enterprises
Model
LADDER MEDIA STAND
Type
Assembly Instructions Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents