Sytech SYXT75BT Owner's manual

Sytech
Brand
Sytech
Model
SYXT75BT
Category
Bluetooth music receivers
Type
Owner's manual
SY·XT75BT
PROFESSIONAL SPEAKER
USER
MANUAL
WELCOME
Welcome to Sytech! Thank you for purchasing the new Professional
Acoustic System SY-XT75BT “Powergenics” Series. Please read this
manual carefully before operating your product and pay close attention
to the precautions which are mentioned below. Store this user manual
in a safe place for future reference
SAFETY INFORMATION AND WARNINGS
Symbol Definitions
DANGER- Indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury. This symbol appears
only in the most extreme situations.
WARNING -
Indicates a potentially hazardous situation which could
result in death or serious injury.
CAUTION- Indicates a potentially hazardous situation, which, if not
avoided, may result in minor/moderate injury or
product/property/damage. It also warns against unsafe practices.
Power source
This symbol means that this unit is double
insulated. An earth connection is not required.
The appliance must be connected to a 100-240V 50/60Hz. AC
supply by means of a two flat pin socket.
Unplug this apparatus during lightning, storms or when
unused for a long period of time to prevent damage to the
product.
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of insulated ‘dangerous voltage’ within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
Warning: to reduce the risk of electric shock do not
remove
cover (or back), no user serviceable parts inside refer
servicing to qualified service personnel.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
To prevent risk of fire or electric shock, avoid overloading
wall outlets, extension cords, or Integral convenience
receptacles.
Use suitable power sources - Plug the product into a suitable
power source, as described in the operating
instructions or as marked on the product.
The supply voltage should be the same as that indicated in
the technical specifications and the appliance rating plate. If
the socket outlets in your home are not suitable for the plug
supplied with this unit check with a qualified electrician for
replacement.
In order to disconnect the apparatus from the mains
c
ompletely, switch off the outlet and remove the mains plug
completely.
Do not bend, stretch or pull the supply cable in order to avoid
electric shock.
When installed, the power socket must be within easy reach.
Moisture and water
•
Do not use this apparatus near water or moisture.
•
Do not use this product near a bathtub, washbowl, kitchen
sink, laundry tub, wet basement, near a swimming pool or
anywhere else that water or moisture is present.
Heat sources and flames
•
Batteries shall not be exposed to excessive heat such as sun
or fire.
•
To prevent risk of fire or electric shock, avoid overloading wall
outlets, extension cords, or integral convenience receptacles.
Servicing and repairs
•
Refer all servicing to qualified service personnel.
•
Servicing is required when the apparatus has been damaged in
any ways: such as liquid has been spilled or objects have fallen
into the apparatus; The apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Warning
The normal function of the product may be disturbed by strong
Electro-Magnetic Interference. If so, simply reset the product to
resume normal operation by following the instruction manual. In
case the function could not resume, please use the product in other
location.
SAFETY INSTRUCTIONS
1)
Read this Instruction Manual before you attempt to connect or
operate the appliance.
2)
Keep these instructions in good condition. Heed all warnings.
Follow all instructions.
3)
Save this Instruction Manual for future reference.
4)
The apparatus shall not be exposed to dripping or splashing and
no objects filled with liquids, such as vases, shall be placed on the
product. Use dry locations only.
5)
No naked flame source, such as candles, should be placed on the
product.
6)
Children should be supervised to ensure that they do not play with
the appliance.
7)
Ventilation should not be impeded by covering the ventilation
openings.
8)
Ensure that the unit is plugged into an AC 100-240V 50/60Hz
power outlet. Using higher voltage may cause the unit to
malfunction or even fire catching. Turn off the unit before
unplugging it from power source to completely switch it off.
9)
Do not plug/ unplug the power plug into/from an electrical outlet
with wet hands.
10)
Use replacement parts, which are specified by the manufacturer.
11)
Install the unit in accordance with the manufacturer’s instructions.
12)
Place the unit where there is good ventilation. Place the speaker
on a flat, hard and stable surface. Do not expose to temperatures
above 40°C. Allow at least 30 cm clearance from the rear and the
top of the unit as well as 5 cm from each side.
13)
Press the buttons of the unit gently. Pressing them too hard can
damage the unit.
14)
Always ensure that the product is unplugged from the electrical
outlet before moving or cleaning. Clean it with dry cloth only.
15)
Unplug the product during lightning, storms or when it will not be
used for long periods of time.
16)
This product has no user serviceable parts. Do not try to repair this
product yourself. Only qualified service personnel should perform
the service. Contact Sytech technical service for a proper
inspection and repair
17)
NEVER let anyone, especially children, insert anything into the
holes, slots or any other openings in the unit’s casing as this could
result in a fatal electric shock.
18)
Don’t mount this product on a wall or ceiling.
19)
Do not place the unit near TVs, speakers and other objects that
generate strong magnetic fields.
20)
Do not leave the unit unattended when it is in use.
NOTE: To disconnect the system completely if it’s not to be used for a long
time, remove the AC power plug from the wall outlet
CONTROL PANEL & FUNCTIONS
BACK PANEL
1.
AC in socket
2.
Power switch
3.
Antenna
TOP PANEL
1. Microphone input
2
. Guitar input
3. AUX input
4. USB charging port (5V 1A)
5. Micro SD card slot
6. USB port for playback
7. MIC.VOL: Increase or decrease the microphone volume
8. ECHO: Increase or decrease the microphone echo effect
9. REC: Start recording
10. REC PLAY: Play recording
11. REPEAT: Repeat one song or all songs
12. LED LIGHT: 1. Press to turn on or off the light
2. Press to change light patterns
13. EQ: Change different EQ mode (Pop, Rock, Jazz, Classic, Country,
User)
14. VOLUME: Rotate knob to increase or decrease the Volume
15. : Press to return to the previous track
16. : Press to skip to the next track
17. Mode: Press to select mode function (USB, TF, AUX, Bluetooth, FM,
TWS)
18. BT Mode: Press this button to select Bluetooth mode
19. : Press to pause or play the track
20. Bass: Increase or decrease the speaker bass effect
21. Treble: Increase or decrease the speaker treble effect
REMOTE CONTROL
1.
Switch to standby mode
2.
Skip to the next track.
3.
Pause or play button
4.
Repeat one song or all songs
5.
Delete recording
6.
Play recording
7.
Microphone priority
8.
Increase or decrease the treble
9.
Increase or decrease the Volume
10.
EQ preset modes
11.
Mute audio playback
12.
Return to the previous track
13.
Mode button
14.
Turn on/off LED light
15.
Start recording
16.
ECHO-: Decrease the
microphone echo effect
17.
ECHO+: Increase the
microphone echo effect
18.
Increase or decrease the bass
19.
Increase or decrease the
Microphone volume
20.
Key number for selecting a
particular track in USB/ Micro SD
Connecting the mains power cable:
1.
Insert the power cord into the mains socket at the rear of the
unit.
2.
Connect the mains plug to a wall outlet.
3.
Set the “POWER” switch to “ON” position. The LED display
will illuminate.
4.
Press the “STANDBY” button on the main unit or on the
remote control to turn on the unit.
Input modes:
Follow the below instructions to switch between Bluetooth, FM radio,
AUX and USB input modes.
1.
Press the MODE button on the main unit or on the remote
control repeatedly to cycle between Bluetooth, FM radio, and
AUX input modes.
2.
Alternatively, press the
“ BT MODE ”
button on the main unit for
direct access to Bluetooth.
TWS Function:
1.
Switch on the 2 speakers and press the “Mode” button to enter
the Bluetooth mode on the 2 speakers.
2.
Long press the “Mode” button on one of the speakers during 4
seconds to enter into TWS pairing mode.
3.
Once the 2 speakers have paired between them, you will hear a
Beep sound indicating that the 2 speakers are now in TWS
mode. The display will indicate “EOEC” on the second speaker,
while the main speaker will indicate “Blue”
4.
Connect your mobile device to Bluetooth and search for
SY-XT75BT. Once found, click on it to pair your mobile to your
speakers.
5.
Playback your favorite tracks and enjoy True wireless sound.
AUX-in input:
Follow the steps below to connect an external audio source
(Smartphone, tablet) to playback your tracks from your Party speaker.
You will need a 3.5mm audio cable or a 3.5mm to RCA cable (not
supplied) to connect your external device to the AUX input socket.
1.
Connect one end of the 3.5mm audio cable to the AUX socket
on top of the unit. Connect the other end to an earphone or line
out socket of the external audio device (Smartphone).
2.
Switch to AUX mode by pressing the MODE button on the main
unit or from the remote control repeatedly until AUX appears on
the LED display.
3.
Press “PLAY” on the external audio device.
4.
Adjust the volume to your desired level.
Note: When connecting via the headphone output, the volume of the
party speakers is affected by the volume control on the player. Ensure
that the audio source (such as MP3 player, smartphone) is set to 70-
80% volume to avoid distortion.
FM Radio operation:
1.
Press the MODE button on the main unit or from the remote
control to access to the FM Radio. The display will change to an
FM Frequency.
2.
Press the “Play button on the main unit or on the remote
control to begin the auto scan process. The unit will save all
the FM stations detected.
3.
Use the
and
buttons to cycle between the saved
station presets.
Note: The position of the party speaker is important for a good FM
reception. If you are unable to find a desired radio station, move the
party speaker to a different location and try to scan again.
Playback MP3 files from a USB:
Follow the steps below to connect a USB drive and playback MP3
files.
1.
Insert a compatible USB flash drive into the USB port (6) of
the speaker located on the top panel.
2.
The device will be automatically detected and the first track in
folder 01 or the root of the USB will start playback automatically.
3.
To pause playback, simply press the button on the main unit
or on the remote-control during playback. To resume playback,
press once more.
4.
To skip to the next or previous track, use the or buttons.
USB / MP3 information:
•
Do not remove the USB device during playback.
•
Maximum reading capacity is 64 GB.
USB Charging port:
1.
The USB charging port (4) allows you to charge your mobile phone
while listening to your favorite tracks.
Note: The maximum charging voltage is set to 5V-1A
Light effect” Gyro LED”:
1. Press the LED/LIGHT button on the speaker or the LED on/off
button on the remote control to turn on the Gyro Led effect.
2. Press the LED/LIGHT button on the speaker to alternate the different
LED patterns.
3. The speaker includes 3 RGB light and 3 different patterns.
When LED lights are on;
Note: If the LED lights are switched off from the remote control, you
can only switch them on from the remote control. The LED function
on the main control board will not respond to the LED light control.
if the LED lights are turned on from the main control panel, the LED
light can be controlled from the remote control or from the main
control panel.
EQ Presets:
1. Press EQ button to select the different EQ presets. There are 6
Equalizer modes from which you can select: POP, ROCK, JAZZ,
CLASSIC, COUNTRY, USER.
Guitar connection:
Follow the below steps to connect a guitar:
1.
Connect the guitar plug to the GUITAR INPUT on the top panel of
the unit.
2.
Once connected, adjust the volume with the buttons Mic+ / Mic-
Microphone recording:
1. Insert a USB drive into the USB port (6)
2. Connect your wired microphone to the microphone input and turn on
the wired mic.
3. Press “REC” button on the speaker (9) or the” REC” button on your
remote control (15) to start recording.
4. To stop recording, simply press the “REC/Play” button on the control
panel (10) or on the remote control (6).
5. Press the “REC play” button to playback the recording.
Mic. Priority:
1. To activate the Mic. Priority function, press the “M.PRI” button on
your remote control (7).
2. This function will automatically decrease the volume level of the
music while the microphone is used.
1.
Press the “MODE” button on the unit or press the “BT MODE”
button directly until “Bt” appears on the LED display of the
speaker. The “Bt” display will start to flash informing that
there is no connected device.
2.
Enable the Bluetooth function on your smartphone, tablet or any
other Bluetooth device which you wish to connect to your speaker
and search for “SY-XT75BT”. Once found, select it to pair your
external device to the speaker. The “Bt” on the LED display will
stop flashing once your device is paired to your speaker.
3.
In the case you are asked to enter a code, please enter “0000”
4.
Once the speaker is connected to your external Bluetooth device,
a sound will be heard confirming the pairing of the two devices.
5.
Each time you switch the Speaker on and select the Bluetooth
mode, the device will automatically pair and connect to the last
device, unless the device has been un-paired on your external
Bluetooth device.
6.
Once the devices are paired up, press the Play/Pause button to
start playback.
7.
When receiving a call during Bluetooth playback, the audio will
automatically stop playing. Once you hang up the call, the music
will restore.
8.
The volume output is affected by the volume level from the
external audio source: For example, if you have paired your
smartphone, you will need to adjust the volume level from your
smartphone to avoid distortion.
Functions and controls:
Once your speaker is connected to an external device via Bluetooth,
you can use the controls located on the top panel of the speaker or
from the remote control.
Bluetooth connection:
To connect a smartphone or any other device to your speaker via
Bluetooth, follow the below steps:
: Playback or pause the track.
: Skip to the next track.
: Skip to the previous track.
Volume control:
•
Rotate the volume knob clockwise on the top panel or press VOL+
button on the remote control to increase the volume output.
•
Rotate the volume knob counterclockwise or press the VOL-
button on the remote control to decrease the volume output.
Mute function:
•
Press the MUTE button on the remote control to silence the audio
playback.
•
Press once again to resume the audio output.
Troubleshooting:
Problem Reason Solution
No Power
Power cable is not
connected to the
wall socket.
Power is not
switched on.
Make sure the plug
is connected.
Switch on the power.
No sound
Volume output is too
low.
AUX/BT source is
too low.
Microphone volume
is too low.
Increase the volume.
Increase the output
volume of the
AUX/BT source.
Increase the volume
of either MIC or
Guitar input.
Sound is distorted Volume is too high.
AUX source volume
is too high.
Reduce the volume.
Reduce the output
volume of the AUX
source.
Remote control is
not working
The batteries are
flat.
Replace the
batteries of the
remote control.
Bluetooth
connection with an
Android device does
not output any
sound
Some older Android
builds may have
incompatibility
issues.
Use the volume
buttons on the
remote control only
to bypass the
incompatibility.
Accessories included:
1.
Remote control
2.
AC cable
3.
Instruction manual
Environment and Compliance:
The European directive 2012/19/EU on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed of
in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimize the recovery and recycling of the materials they
contain, and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the appliance, it must be
separately collected.
To avoid possible hearing damage, do not listen at h
igh audio volume
for a long period of time.
TECHNICAL SPECIFICATIONS
Basic Specifications
• 2-way electronic divider amplifier system (2 IC amplifier)
• Built-in amplifier for connecting musical instruments: Electric guitar,
Electronic keyboard
• FM tuner with 30 preset memory system
• LED display
• RGB light. Red, Green, Blue, 3 patterns.
• 1 x Mic input (6.3mm); 1 x Guitar input (6.3mm); AUX (3.5mm)
• TWS function
• Remote control
• 2 wheels and handle for carrying
Bluetooth Specifications
• Bluetooth Module: AB5301A Bluetrum
• Bluetooth Version: V5.0
• Bluetooth Profiles: A2DP, AVRCP
• Bluetooth Pairing name: SY-XT75BT
• Compatible with: IOS, Android, Windows, Blackberry,
MAC OS, etc…
USB 1 Specifications
• 2.0 USB Port (Max Capacity : 64GB)
• Compatible Audio Formats in USB: MP3/WMA
USB 2 Specifications
• USB Port charging function
• Power: 5V.1-A
Technical Specifications
• Output power RMS: 140W
• Output power PMPO: 900W
• Frequency response: 20Hz-20kHz
• SNR: ≥60dB
• Power supply: AC~100-240V 50/60Hz
• 2 ways speakers: Woofer: 2 x 10” 8 Ohms
Tweeter: 1 x 1.5” 8 Ohms
Dimensions and weight:
• Unit dimension : (LxWxH): 40,0 x 30,0 x 120,0 cm.
• Weight: 15,5 Kg.
• Above specifications are the specifications of SY-XT75BT
“Powergenics Series” and are for reference purpose only.
• Due to continuous product development, specifications may be
subject to change without prior notification.
• Do not expose to adverse weather conditions (Such as rain or high
temperatures) as it can cause malfunctions.
DECLARATION OF CONFORMITY
Manufacturer Name: Satyatrade S. L.
Address: Pol.Ind.La Raya. C/ Guadalquivir, 2.
Camarma de Esteruelas, 28816 Madrid
Tel: 902 430 967
Fax: 91 8864285
NIF: B84254763
Manufacturing country: China
Description: Party speaker Gyro LED
Sytech® SY-XT75BT complies with the following directives:
RED Standard: Directive 2014/53/EU
ROHS Standard: Directive 2015/863/EU Restriction of Hazardous Substances
Signed: Ajeet Nebhwani Utamchandani
Sole Administrator
www.sytech.es
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Sytech SYXT75BT Owner's manual

Sytech
Brand
Sytech
Model
SYXT75BT
Category
Bluetooth music receivers
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents