Geemarc CL 2L Owner's manual

Brand: Geemarc

Model: CL 2L

Category: Wall & ceiling mounts accessories

Type: Owner's manual

CL2L

Telephone rin

er amplifier with

flasher and

door bell

Indicateur d’appel téléphonique avec flash

et sonnette

Telefonklingelverstärker mit

Blitz und Türklingel

English Page 2

Français Page 15

Deutsch Page 28

CAUTION: The switch for Ringer ALARM

selection must never be set during ringing/

flashing mode but always when CL2 is silent

mode ( No incoming call ringing).

ATTENTION: Le commutateur de configuration

du mode Alarme ne doit jamais être changé

lorsque le CL2 envoie sa sonnerie ( ou flash

lumineux ) mais uniquement durant le mode

repos.

WARNUNG: Bitte die Taste für die Auswahl

des Klingeltons niemals während des Läutens

bzw. Blitz-Signals betätigen, sondern nur im

Ruhe-Modus ( kein eingehender Anruf ).

DESCRIPTION

1. DESCRIPTION

The CL2 will alert you to both doorbell and telephone. It

has adjustable volume and different tone settings for

doorbell and telephone.

(*) Classified TNV-3 according to EN60950 standard.

Door bell

LED

4 ringer

settings

Volume

control

Doorbell Tone

control

Phone ringer

amplifier tone

control

Strobe flasher Loud sound

alarm

FRONT VIEW

REAR VIEW

BELL PUSH

Bell push

button

Wall mountin

Paring/Test

holes

Telephone line

cord socket

(

)

Modular jack for

tele

hone line cord

(

)

Mains power lead socket (*)

Shaker socket (*)

INSTALLATION

2. INSTALLATION

230V

AC/DC

Double plug

Wall socket

Telephone

Option :

to link

two CL2s

Screw wall mount

Door Bell

Button

Door Bell

Special cable

Option : Shaker

(ref.: SHAKCL_BLK only)

1 - Connect the CL2 line cord in CL2 “Line IN”.

2 - Connect your Telephone in the double plug of the line

cord.

3 - Connect the double plug in the Telephone wall socket.

4 - If necessary connect the required shaker

(SHAKCL_BLK only) to the shaker plug input.

5 - Connect the mains adaptor line cord in CL2 12V DC

input.

6 - Connect the mains adaptor in the 230V wall socket.

(*)

INSTALLATION

(*) Classified "hazardous voltage" according to EN60950

standard.

Electrical connection: The apparatus is designed to

operate from a 230V 50Hz supply only. (Classified as

'hazardous voltage" according to EN60950 standard).

The apparatus does not incorporate an integral power

on/off switch. To disconnect the power, either switch off

supply at the mains power socket or unplug the AC

adaptor. When installing the apparatus, ensure that the

mains power socket is readily accessible.

Telephone connection: Voltages present on the

telecommunication network are classified TNV-3

(Telecommunication Network Voltage) according to the

EN60950 standard.

BELL PUSH WALL MOUNTING

3.1. BELL PUSH – WALL MOUNTING

The wire free bell push is mounted by the front door. It

has a range of 20-60 metres depending on the structure

of the building (see note).

Test the system before mounting

on the wall – plug in the CL2 and

press the bell push button to

check that the CL2 rings.

To mount the bell push, open

the access cover in the middle of

the bell push with a needle or

small screwdriver.

Decide where to position the bell

push and use the wall mount

template, shown below, to mark

the holes on the wall or door

surround and drill holes if

necessary.

Align with prepared marks or screwholes, insert and

tighten screws and replace access cover.

Bell push is now ready for use.

Note: Do not place the bell push onto a metallic base or

near electric equipment (such as TV, Radio, computer,

washing machine...). The CL2 will work within a range of

60m in an environment where there are no obstacles

and 20m in an environment which contains a wall or

metallic structure.

WALL MOUNTING BELL PUSH

WALL MOUNTING TEMPLATES

To wall mount the bell push or the CL2, use these

templates to mark the screw hole centres. We

recommend the use of a spirit level to ensure the holes

are level.

CL2 template

Bell push template

BELL PUSH CHANGE THE BATTERY

3.2. CHANGE THE BATTERY

The door bell is supplied with a 23A 12V battery. The

CL2 is supplied ready to use, it is not necessary to open

the bell push when you first install the CL2.

To replace the battery, open the access cover and

unscrew the door bell from the wall, unscrew the three

screws located on the base and open the box to get

access to the battery compartment. Replace the battery,

replace back and remount.

Back of Bell Push Inside Bell Push

Unscrew to

open

Battery

Switches for

LED colour

Note: Do not use a rechargeable battery. Do not put the

used battery into the household rubbish, pay attention to

battery regulations regarding battery disposal.

CL2 SETTINGS

4.1. CL2 SETTINGS

ALARM MODE SETTING

For incoming calls – choose

which alarm mode you want by

moving the alarm mode switch

to one of the following positions:

No alarm selected

Doorbell/ringer

amplifier and strobe

flasher Flasher:

Bell push – 3-4 flashes

Telephone – flashes as

long as phone rings

Doorbell, strobe

flasher and shaker

(if connected)

Doorbell/ringer amplifier and shaker

(if connected)

VOLUME CONTROL

For doorbell and ringer amplifier:

Use the slider control to adjust

the volume of the sound alarm

of the CL2.

SETTINGS CL2

RING TONE CONTROL

The three position switch allows

you to set the tone of the CL2

ringer when the telephone rings.

DOOR BELL TONE CONTROL

This three position switch allows

you to set a different tone when

the door bell rings.

OPTIONAL ACCESSORIES:

Extra bell push – to cover a second door, such as a

kitchen door.

Shaker – the Geemarc shaker unit (CLA2) can be

tucked under your pillow or at the side of your chair to

vibrate when the doorbell or telephone rings. Particularly

useful for hearing aid wearers, when they are not

wearing their hearing aids at night.

Wrist watch alarm – can be worn by someone in the

house who is bedbound and may need to call for help.

To purchase these items, contact your dealer. In case of

difficulty, visit the Geemarc website on:

www.geemarc.com

PAIRING SETTINGS

4.2. The Pairing Procedure

( Note : Factory default setting : paired. )

1. Press and hold the (Pairing/Test) button for 2

seconds to enter pairing mode, at the same time, the

unit makes a beep sound.

2. The 1st LED lights, to pair the BELL PUSH, press and

hold the (Pairing/Test) button and then Bell

push button at the same time, the 1st LED flashes,

after paired, the 1st LED lights and stop flashing,

beeps to confirm.

3. If user wants to pair the 2nd or 3rd BELL PUSH, when

the 1st LED lights, press the (Pairing/Test)

button within 2 seconds, the 1st LED goes off and

then the 2nd LED lights. User is able to pair the 2nd

BELL PUSH, repeat the same procedure for the 3rd.

4. Repeat the above, all 3 LEDS flashing together for the

4th BELL PUSH pairing, the BELL TONE is not

adjustable for the 4th BELL PUSH.

5. If paired more BELL PUSH on same LED, only the

last one kept.

SETTINGS PAIRING

4.3. Un- Register The Pairing

1. Press and hold the Pairing/Test button for 5 seconds

to enter un-register mode, 3 LED light together.

2. If user wants to un-register the 1st BELL PUSH,

press the Pairing/Test button within 2 seconds, the 1st

LED will be flashing (the other 2 LED light), means

user is now un-registering the 1st BELL PUSH, press

the Pairing/Test button until the 1st LED goes off,

beeps to confirm. The 1st remote is now un-registered.

3. If user wants to keep the 1st BELL PUSH but un-

flashes, press the Pairing/Test button within 2 seconds,

the 2nd LED flashes (other 2 LED light), to select

which BELL PUSH to be un-registered.

Note :

1. To check whether the unit works normally, you can

press the (pairing/Test) button, the unit would

sound alarm and flash.

2. Don’t unregister a BELLPUSH unless it is really

necessary.

TROUBLESHOOTING

5. TROUBLESHOOTING

If the CL2 system doesn't work correctly, please carry

out the following checks before calling the helpline:

● If the phone rings but the CL2 does not ring:

Check the connection between the phone socket and the

CL2.

● If the door bell does not ring:

1. Check that the CL2 is plugged into the mains and

switched on.

2. Unscrew the bell push and check the battery is

correctly fitted.

3. Try fitting a new battery.

4. Check that the Bell push paired with CL2, please refer

to page 10/Setting for how to pair the Bellpush with

CL2.

6. GUARANTEE

From the moment your Geemarc product is purchased,

Geemarc guarantee it for the period of one year. During this

time, all repairs or replacements (at our discretion) are free of

charge. Should you experience a problem then contact our

helpline or visit our website at www.geemarc.com.

The guarantee does not cover accidents, negligence or

breakages to any parts.

The product must not be tampered with or taken apart by

anyone who is not an authorised Geemarc representative.

The Geemarc guarantee in no way limits your legal rights.

IMPORTANT: YOUR RECEIPT IS PART OF YOUR

GUARANTEE AND MUST BE RETAINED AND

PRODUCED IN THE EVENT OF AWARRANTY CLAIM.

GUARANTEE

The guarantee applies to the

United Kingdom only.

Declaration: Geemarc Telecom SA hereby declares that

this product is in compliance with the essential

requirements and other relevant provisions of the Radio

and Telecommunications Terminal Equipment Directive

1999/5/ EEC and in particular article 3 section 1a, 1b

and section 2.

The declaration of conformity may be consulted at

www.geemarc.com

RECYCLING DIRECTIVES

7. RECYCLING DIRECTIVES

Recycling directives: The WEEE (Waste Electrical and

Electronic Equipment) Directive has been put in place so

that products at the end of life are recycled in the best

way.

When this product is out of order, please do not put it in

your domestic waste bin. Please use one of the following

disposal options:

– Remove the batteries and deposit them in an

appropriate WEEE skip. Deposit the product in an

appropriate WEEE skip.

– Or hand the old product to the retailer. If you purchase

a new one, they should accept it.

Thus if you respect these instructions you ensure human

health andenvironmental protection.

For product support and help visit our website at

www.geemarc.com

Telephone: +44 (0)1707 384438

or Fax +44 (0)1707 832529

Geemarc CL 2L Owner's manual

Brand: Geemarc

Model: CL 2L

Category: Wall & ceiling mounts accessories

Type: Owner's manual

Download PDF

report

Geemarc CL 2L Owner's manual

Geemarc CL 2L Owner's manual

Related papers

Other documents