Festool CDD 9.6 FX User manual
- Category
- Cordless combi drills
- Type
- User manual
1
462069_002
Manual de instrucciones
Página 13
IMPORTANTE: Lea y comprende todas las
instrucciones antes de usar.
Guide dutilisation
Page 8
IMPORTANT: Lire et comprendre toutes les
instructions avant de démarrer les travaux.
Instruction manual
Page 4
IMPORTANT: Read and understand all
instructions before using.
Cordless Drill /
Screwdriver
Perceuse visseuse á
accumulateur
Taladradora-atornilladora
con acumuladores
CDD 9.6 FX
CDD 12 FX
Seen at Ideal Tools.
2
Seen at Ideal Tools.
3
Seen at Ideal Tools.
4
GENERAL SAFETY RULES
WARNING! Read and understand all
instructions. Failure to follow all instructions listed
below, may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
Work area
1Keep your work area clean and well lit.
Cluttered benches and dark areas invite accidents.
2Do not operate tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Tools create
sparks which may ignite the dust or fumes.
3Keep bystanders, children, and visitors
away while operating a tool. Distractions can
cause you to lose control.
Electrical safety
4A battery operated tool with integral
batteries or a separate battery pack must be
recharged only with the specified charger for
the battery. A charger that may be suitable for
one type of battery may create a risk of fire or
electric shock when used with another battery.
5Use battery operated tool only with
specifically designated battery pack. Use of any
other batteries may create a risk of fire.
Personal safety
6Stay alert, watch what you are doing and
use common sense when operating a tool. Do
not use while tired or under the influence of
drugs, alcohol, or medication. A moment of
inattention while operating tools may result in
serious personal injury.
7Dress properly. Do not wear loose clothing
or jewellery. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts.
Loose clothes, jewellery, or long hair can be caught
in moving parts.
8Avoid accidental starting. Ensure switch is
in the off position before plugging in or
inserting battery pack. Carrying tools with your
finger on the switch or energising tools that have
the switch on invites accidents.
9Remove adjusting keys or wrenches before
turning the tool on. A wrench or key that is left
attached to a rotating part of the tool may result in
personal injury.
10 Do not overreach. Stand on both feet an
keep proper footing and balance at all times.
Proper footing and balance enables better control
of the tool in unexpected situations.
11 Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for
appropriate conditions.
12 If devices are provided for the connection
of dust extraction and collection facilities
ensure these are connected and properly used.
Use of these devices can reduce dust related
hazards.
Tool use and care
13 Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
14 Do not force tool. Use the correct tool for
your application. The correct tool will do the job
better and safer at the rate for which it is designed.
15 Do not use tool if switch does not turn it
on or off. Any tool that cannot be controlled with
the switch is dangerous and must be repaired.
16 Disconnect battery pack from tool before
making any adjustments, changing
accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool
accidentally.
17 Store idle tools out of reach of children and
other untrained persons. Tools are dangerous
in the hands of untrained users.
18 When battery pack is not in use, keep it
away from other metal objects like: paper
clips, coins, keys, nails, screws, or other small
metal objects that can make a connection
from one terminal to another. Shorting the
battery terminals together may cause sparks,
burns, or a fire.
19 Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools, with
sharp cutting edges are less likely to bind and are
easier to control.
20 Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly
maintained tools.
21 Use only accessories that are
recommended by the manufacturer for your
model. Accessories that may be suitable for one
tool, may become hazardous when used on another
tool.
Service
22 Tool service must be performed only by
qualified repair personnel. Service or
maintenance performed by unqualified personnel
could result in a risk of injury.
23 When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unauthorised parts or failure to follow Maintenance
instructions may create a risk of electric shock or
injury.
Seen at Ideal Tools.
5
Technical data
Cordless drill/screwdriver CDD 9.6 FX CDD 12 FX
Motor voltage 9.6 V 12 V
Idle-running speed 1. speed 0 380 rpm 0 - 380 rpm
2. speed 0 - 1100 rpm 0 - 1100 rpm
Max torque Soft boring (wood) 10 Nm 18 Nm
Hard boring (metal) 26 Nm 30 Nm
Adjustable torque 0.5 - 5 Nm 1 - 7 Nm
Chuck capacity 1 - 10 mm 1,5 - 13 mm
Max. drill diameter for metal / wood 12 mm / 20 mm 14 mm / 25 mm
Tool fitting in chuck 1/4 1/4
Weight with battery pack 1.8 kg (4.0 lbs) 2.0 kg (4.4 lbs)
Charger MC 15
Supply voltage (input) 120 V ~
Line frequency 60 Hz
Charging voltage (output) 4.8 - 12 V (DC)
Charging current quick charge max. 7.5 A
Compensation charge pulsating app. 0.03 A
Charging time for NiCd 1.4 Ah app. 13 min
NiCd 1.7 Ah app. 15 min
NiCd 2.0 Ah app. 18 min
Weight 0.9 kg (2.0 lbs)
Battery pack BPH 9.6 C BPH 12 C
Order number 488 437 488 438
Voltage 9.6 V 12 V
Cells 8 x 1.2 V, NiCd 10 x 1.2 V, NiCd
Capacity 2.0 Ah 2.0 Ah
Temp. range for charging 5 - 45 °C 5 - 45 °C
Monitoring of charge by means of NTC thermistor
Weight 0.5 kg (1.1 lbs) 0.6 kg (1.3 lbs)
The illustrations mentioned can be found at the beginning of the operating instructions.
1Symbols
Vvolts
Aamperes
Hz hertz
W watt
alternating current
n0no load speed
Class II Construction
rpm revolutions per minute
2Intended use
The cordless drill/screwdrivers are suitable for
drilling metal, wood, plastic and similar materials,
as well as for fastening and screwing down of
screws with a diameter up to 6 mm.
The chargers have been designed to charge the
battery packs specified under 3.2.
The user will be liable for damage due to improper
use.
3Preparation for initial operation
3.1 Remove battery pack from unit
The battery pack (1.2) is unlocked and can be
removed by pressing the switch (1.1) downwards.
3.2 Charge battery pack
a) MC 15
The charger MC 15 can be used to charge all
NiCd-FESTOOL battery packs between 4.8 V and
12 V in the battery chamber (3.1).
The charge process is controlled by a micro-
processor. The optimum charging current is
always used depending on the temperature,
voltage and internal resistance.
The LED (3.2) indicates the respective charging
operation of the charger.
LED yellow - steady =
Charger is ready for use.
LED green - flashing =
Battery pack being charged.
LED green - fast flashing =
Battery pack being charged at max. charging
current.
LED green - steady =
Battery pack fully charged, conservation
charge on.
LED red - flashing =
General malfunction, e. g. incorrect polarity
of battery pack, full contact not being made,
short-circuit, battery pack faulty.
LED red - steady =
Temperature of battery pack is outside
permissible limit.
If the battery pack is removed from the charging
chamber during charging, charging can only be
continued after 1-2 seconds when the LED shows
a steady yellow.
Seen at Ideal Tools.
6
b) Charging with the MC 15
-Connect charger to mains. The line
voltage and frequency must correspond with
the data on the ratings plate!
-Insert battery pack with the fin (2.2) in the
lower groove (3.4) of the charging chamber.
-Push battery pack into charging chamber until
it catches with the lock (2.3) in the groove
(3.3).
The battery pack is now charged.
Press the button (1.1) to unlock it and remove it
from the charger.
3.3 Fitting the battery pack in the tool
-Place the charged battery pack with its fin (2.2)
in the groove (2.1).
-Push the battery pack towards the tool until
its lock (2.3) catches in place.
The cordless drill/screwdriver is now ready for
operation.
Note: The cordless drill/screwdriver can be
operated with a battery pack whose voltage is
lower than the motor voltage of the cordless drill/
screwdriver, though not vice versa!
4Initial operation
Turn on by pressing button (1 3). Depending on
the pressure exerted on the button, the
adjustment of running speed can be varied
infinitely.
Turn off by releasing the button. After releasing
the button, the chuck is stopped and therefore,
after-running of the equipment is prevented.
4.1 To change the direction of rotation
The selector button (1.4) determines the direction
of rotation.
- Turn button from right to left = clockwise
rotation.
- Turn button from left to right = anticlockwise
rotation.
-Selector button in central position = circuit
interlock.
4.2 Shifting speeds
Change only when completely
stopped! Using the shift lever (1.5), the speed
can be changed. If the shift lever cannot be
switched completely, slightly turn the chuck.
1. Speed: lever forward - Figure 1 is visible.
2. Speed: lever backwards - Figure 2 is visible.
4.3 Torque adjustment
By turning the adjustment ring (1.7), so that the
corresponding symbol aligns with the arrow (1.6)
the required torque can be adjusted.
a) Drilling:
Drilling symbol on adjustment ring aligns with
the arrow = maximum torque.
b) Screws:
Torque corresponding to setting:
Position 1 = low torque
Position 18 = high torque
5Tool holding fixture, attachments
Make sure that the machine is
switched of and the battery block has been
removed before changing the tool holding fixture,
attachments and tools.
5.1 Chuck BF-FX
The chuck is used to clamp drills and bits.
5.1.1 Fitting / removing the chuck
Fitting:
-Place the chuck on the drill spindle (2.11) and
twist until the hexagon key (2.10) of the chuck
latches into the hexagon socket of the drill
spindle.
-Pull the unlocking ring (2.9) forwards, press
the chuck onto the drill spindle up to the stop
and release the unlocking ring.
Removal:
-Pull the unlocking ring forwards and remove
the chuck.
5.1.2 Changing tools
- Turn the clamping sleeve (2.8) anti-clockwise
to open the clamping jaws (2.7) (Note: the
spindle is automatically locked when the
machine is switched off).
-Insert the tool into the chuck.
-Clamp the tool by turning the clamping sleeve
clockwise. Always make sure that the tool is
clamped centrally in the chuck.
5.2 Angle attachment DD-AS
The angle attachment permits work (drilling,
screwing) vertical to the machines longitudinal
axis.
5.2.1 Fitting / removing the angle attach-
ment
Fitting:
-place the angle attachment on the drill spindle
and turn until it catches in the desired position
(Note: The angle attachment can be fitted in
16 different angle settings).
-Lock the angle attachment by turning the
fastening ring (2.6) tightly clockwise.
Removal:
- Turn the fastening ring anti-clockwise up to
the stop and remove the angel attachment.
5.2.2 Fitting / removal of chuck on angle
attachment
The chuck is fitted on the shaft (2.5) of the angle
attachment in the same way as on the drill spindle
of the machine.
5.3 Eccentric attachment DD-ES
The eccentric attachment is used to hold bits. It
allows screwing close to edges.
5.3.1 Fitting / removing the eccentric
attachment
The eccentric attachment is fitted / removed in
the same was as the angle attachment (see
Chapter 5.2.1).
Seen at Ideal Tools.
7
5.3.2 Changing tools
-Pull the unlocking ring (2.4) back and remove
the tool and/or insert the new tool.
5.4 Tool holding fixture in the drill spindle
Bits can be fitted directly in the hexagon socket
holder of the drill spindle (2.11) to make the
machine lighter and shorter.
6Accessories, tools
The accessory and tool order number can be
found in the Festool catalogue or on the Internet
under "www.festool.com".
Bit depot
Attachments which are used on a regular basis,
as for example the chuck key (4.2), bit extender
(4.3) or different bits (4.5), can be clipped onto
the bit depot (4.1).
The bit depot can be snapped into the bottom
of the drill/screwdriver with its mounting lugs
(4.6). When the mounting lugs are inserted into
the corresponding holes (4.4) and the magazine
is slid sideways the contour of the case aligns
with the contour of the magazine.
The spring loaded catch of the bit magazine can
loosen on impact of drill/screwdriver.
7lnstructions on application -
maintenance - care
Please pay attention to the following
instructions. Otherwise there is a risk of damage
to the tool, charger or battery pack.
Keep the air vents of the electronic equipment
and the charger clean to guarantee the air
circulation for cooling.
Keep the connection contacts of electronic
equipment, charger and battery pack clean.
Festool chargers and Festool battery packs
are designed for each other. Therefore, only
use Festool chargers to charge Festool battery
packs.
By keeping the battery pack in a ready for use
charger, the battery pack will be kept in a state
of readiness by float charging conservation.
Do not keep discharged battery pack
(maximum one month) attached to charger
whenever charger is detached from the power
supply (danger of deep discharging).
A new battery pack or a battery pack not used
for a longer period of time reaches it's full
capacity after about 5 charging and discharging
cycles.
Battery packs should, before charging, be fully
discharged if possible. Continuous starting of
the charging process shortens the lifespan of
the batteries.
A considerably reduced time of operation per
charging shows that the battery pack is used
up an should be replaced by a new one.
Store battery packs at ambient temperatures
between 0°C and 35°C.
All maintenance and repair work, requiring
dismantling of equipment, may only be
performed by an authorised after-sales service
workshop.
8Recycling battery packs
Never throw spent battery packs into
domestic waste containers! Return spent or
defective battery packs to dealers, the Festool
after-sales service department or approved waste
disposal facilities. This ensures that they are
correctly recycled.
9Warranty
Festool warrants, that all Festool portable power
tools will be free from defects in materials and
workmanship for a term of one year from the date
of procurement. Festool makes no other warranty,
express or implied, for all Festool portable power
tools. No agent, representative, distributor, dealer,
or employee of Festool has the authority to
increase or otherwise change the obligations or
limitations of this warranty. The obligations of
Festool in its sole discretion under this warranty
shall be limited to the repair or replacement of
any Festool portable power tool which is found to
be defective as packaged with this User Manual.
Excluded from the coverage under this warranty
are: normal wear and tear; damages caused by
misuse, abuse or neglect; damage caused by
anything other than defects in material and
workmanship.
Returning product: Call us for authorisation.
For product returns: (888) 463-3786
For service or repairs: (800) 554-8741
We will supply you with the correct address for
your return. This is important because not all types
of returns are to be shipped to the same address.
IN NO EVENT SHALL FESTOOL BE LIABLE FOR
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY,
EXPRESSED OR IMPLIED WHATSOEVER.
ALL WARRANTIES IMPLIED BY STATE LAW,
INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE HEREBY LIMITED TO
THE DURATION OF ONE YEAR.
Some states in the U.S. and some Canadian
provinces do not allow the limitations on how long
an implied warranty lasts, so the above limitation
may not apply to you. With the exception of any
warranties implied by state or province law as
hereby limited, the foregoing express limited
warranty is exclusive and in lieu of all other
warranties, guarantees, agreements and similar
obligations of Festool.
This warranty gives you specific legal rights and
you may also have other rights which vary from
state to state in the U.S. and province to province
in Canada.
Seen at Ideal Tools.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Festool CDD 9.6 FX User manual
- Category
- Cordless combi drills
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Festool CDD 12 User manual
-
-
-
-
-
Festool 564274 User manual
-
-
-
-
Festool C12 LI Owner's manual