Transolid TFH-2522-MB Installation guide

Transolid
Brand
Transolid
Model
TFH-2522-MB
Type
Installation guide

This manual is also suitable for

Rack Installation
Strainer Installation
Rack
P-trap Installation
Washing Stand
Left Side Panel FaucetA K
L
M
O
P
Q
R
N
B L
C M
D N
E5
2
10
1
O
F P
G Q
H R
I S
J T
Round Insert Bar Gasket
Right Side Panel Strainer Gasket
Square Base Bar with connector Double Lip Seal
Front Panel Screw
Adjustable Metal Feet Waste Bowl
Hand-Tighten Thumb Screws Fitting
Back Panel Strainer Bowl
Screw Flat Gasket
Utility Sink P-Trap
S
GH
E
D
F
C
B
A
I TK
J
O
OJ
P
Q
R
S
J
JP
N
N
Q
M
M
R
RQQ
S
L
L
N
5. If you want to connect the faucet with , remove the aerator shell (1), aerator(2) and washer(3) from spray head
by the aerator wrench (5). Then reinstall the washer (3) into the spray head, and thread the connector (4) onto the spray head.
garden hose
K
J
3
2
1
5
3
2
4
1.Turn the left panel and right panel side onto protective surface.
panel(B).
3.Connect one square base bar (F) with right and left panel with
connecters and tighten the screws(H
4.Place the 4 round insert bar (E) into the bottom holes.
Place the last round insert bar (E) into the towel bar hole.
5.Connect another square base bar (F) with right and left panel
with connecters and tighten the screws .
2.Attached the adjustable feet (G) on the left panel(A)and right
).
(H)
6.Gently put the rack upright.
7.Screw the hand-tighten thumb screws (I) into the holes on the
rack and tighten.
8.Slide the front panel (C) and black panel (D) into the rack.
washing stand
E
D
C
I
I
G
BA
H
F
H
F
E
1. Security the rack into screw hole by black panel(screws are not provided) if needed.
2. Carefully place a bead of sealant around the top of the rack if needed.
3. Ease the sink into the rack, ensuring that it is placed evenly and centered on the rack.
4. Wipe off any excess sealant, use masking tape to hold the sink in place until the sealant dries.
1. Meansure and cut the wall tube(B1)to length required.
2. Position nut (A1) on the wall tube (B1).
3. Insert the tube (B1) into waster connector and tighten existing nut.
4. Position nut (C1) and washer (D1) onto tailpiece S , Use reducer wa her (F1) if tailpiece is 1 1/4 in.
5. Slip tailpiece into J-bend (E1).
6. Tighten nuts and check for leaks.
7. The suitable height of wall outlet hole installation is from 16.5in to 17.8in.
( ) s
P-TRAP INSTALLATION
C1
S
B1
A1
F1
D1
E1
Conector
J
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Transolid TFH-2522-MB Installation guide

Transolid
Brand
Transolid
Model
TFH-2522-MB
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents