Table of Contents
Cover photo may show optional equipment
not supplied with standard unit.
Read the Operator’s Manual entirely. When you
see this symbol, the subsequent instructions and
warnings are serious - follow without exception.
Your life and the lives of others depend on it!
!
© Copyright 2015 Printed
35783
310-366M
FDR1648, FDR1660 & FDR1672 PATRIOT Model
®
30248
FDR1648
FDR1660 & FDR1672
Operator’s Manual
Rear Discharge Grooming Mowers
11 / 2 0 / 15
Table of Contents
FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M 11/20/15
© Copyright 2015 All rights Reserved
Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future.
Land Pride is a registered trademark.
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
Important Safety Information . . . . . . . . . . . . . 1
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Further Assistance . . . . . . . . . . . . . . . . . . . . . . . . 8
Section 1: Assembly & Set-Up . . . . . . . . . . . 10
Tractor Requirements . . . . . . . . . . . . . . . . . . . . . . 10
Torque Requirements . . . . . . . . . . . . . . . . . . . . . . 10
Dealer Preparations . . . . . . . . . . . . . . . . . . . . . . . 10
Vented Dipstick Installation . . . . . . . . . . . . . . . . . . 10
Upper 3-Point Hitch Assembly . . . . . . . . . . . . . . . . 10
Gauge Wheel Assembly . . . . . . . . . . . . . . . . . . . . 11
Lower 3-Point Clevis Hitch Assembly . . . . . . . . . . 11
Tractor 3-Point Hook-up . . . . . . . . . . . . . . . . . . . . 12
Top Center Link Adjustment . . . . . . . . . . . . . . . . . 12
Quick Hitch Hook-up . . . . . . . . . . . . . . . . . . . . . . . 13
Driveline Hook-up to Gearbox . . . . . . . . . . . . . . . . 13
Driveline Hook-up to Tractor . . . . . . . . . . . . . . . . . 14
Check Driveline Collapsible Length . . . . . . . . . . 14
Shorten Driveline . . . . . . . . . . . . . . . . . . . . . . . . 14
Check Maximum Allowable Length . . . . . . . . . . 15
Check Driveline Interference . . . . . . . . . . . . . . . 15
Section 2: Accessories & Set-up . . . . . . . . . 16
Front Roller Assembly . . . . . . . . . . . . . . . . . . . . . . 16
Cutting Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Low Lift Blades . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Medium Lift Blades (Factory Standard) . . . . . . . 16
High Lift Blades . . . . . . . . . . . . . . . . . . . . . . . . . 16
Mulching Blades . . . . . . . . . . . . . . . . . . . . . . . . . 16
Accessory Part Numbers . . . . . . . . . . . . . . . . . . . . 16
Section 3: Operating Instructions . . . . . . . . . 17
Operating Check . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Pre-Start Checklist . . . . . . . . . . . . . . . . . . . . . . . . . 17
Tractor Shut Down Procedure . . . . . . . . . . . . . . . . 17
Inspection Procedures . . . . . . . . . . . . . . . . . . . . . . 17
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . 18
Unhooking the Mower . . . . . . . . . . . . . . . . . . . . . . 20
General Operating Instructions . . . . . . . . . . . . . . . 20
Section 4: Adjustments . . . . . . . . . . . . . . . . . 21
Leveling the Mower . . . . . . . . . . . . . . . . . . . . . . . . 21
Cutting Height Adjustment . . . . . . . . . . . . . . . . . . . 21
3-Point Hitch Adjustments . . . . . . . . . . . . . . . . . . . 21
Belt Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Section 5: Maintenance & Lubrication . . . . . 22
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Service Mowing Blades . . . . . . . . . . . . . . . . . . . . . 22
Blade Inspection . . . . . . . . . . . . . . . . . . . . . . . . . 22
Blade Sharpening or Replacement . . . . . . . . . . . 23
V-Belt Installation . . . . . . . . . . . . . . . . . . . . . . . . . 23
Storage Instructions . . . . . . . . . . . . . . . . . . . . . . . . 24
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Driveline Shaft U-Joints . . . . . . . . . . . . . . . . . . . 25
Inner Tube Bearings . . . . . . . . . . . . . . . . . . . . . . 25
Driveline Profiles . . . . . . . . . . . . . . . . . . . . . . . . 25
Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Wheel Support Busings & Wheel Bearings . . . . . 26
Bearing in Blade Spindle Hubs . . . . . . . . . . . . . . 26
Section 6: Specifications & Capacities . . . . . 27
Section 7: Features & Benefits . . . . . . . . . . . 28
Section 8: Troubleshooting . . . . . . . . . . . . . . 29
Section 9: Torque Values Chart . . . . . . . . . . 30
Section 10: Warranty . . . . . . . . . . . . . . . . . . . 31
Table of Contents
1
Important Safety Information
11 / 2 0 / 15 FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M
Table of Contents
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
▲
Parts Manual QR Locator
The QR (Quick Reference) code on the
cover and to the left will take you to the
Parts Manual for this equipment.
Download the appropriate App on your
smart phone, open the App, point your
phone on the QR code and take a picture.
Dealer QR Locator
The QR code on the left will
link you to available dealers
for Land Pride products.
Refer to Parts Manual QR
Locator on this page for
detailed instructions.
!
Be Aware of
Signal Words
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
!
DANGER
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
!
WARNING
!
CAUTION
Safety at All Times
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read all
instructions noted on them.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
▲The operator must not use drugs
or alcohol as they can change the
alertness or coordination of that
person while operating equipment.
The operator should, if taking over-
the-counter drugs, seek medical
advice on whether he/she can
safely operate the equipment.
▲Operator should be familiar with all
functions of the unit.
▲Operate controls from the driver’s
seat only. Never operate controls
from the ground.
▲Make sure all guards and shields
are in place and secured before
operating implement.
▲Keep all bystanders away from
equipment and work area.
▲Do not leave tractor or implement
unattended with engine running.
▲Dismounting from a moving tractor
can cause serious injury or death.
▲Do not allow anyone to stand
between tractor and implement
while backing up to implement.
▲Keep hands, feet, and clothing
away from power-driven parts.
▲Watch out for fences, trees, rocks,
wires, etc., while operating and
transporting implement.
▲Turning tractor too tight may cause
hitched machinery to ride up on
wheels. This could result in injury
or equipment damage.
Look For The Safety Alert Symbol
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control, and accident prevention are
dependent upon the awareness, concern, prudence, and
proper training of personnel involved in the operation,
transport, maintenance, and storage of equipment.
For Your Protection
▲Thoroughly read and understand
the “Safety Label” section, read
all instructions noted on them.
Tractor Shutdown & Storage
▲If engaged, disengage PTO.
▲Lower attached implement to
ground, put tractor in park or set
park brake, turn off engine, and
remove switch key to prevent
unauthorized starting.
▲Wait for all components to come to
a complete stop before leaving the
operator’s seat.
▲Detach and store implement in an
area where children normally do
not play. Secure implement using
blocks and supports.
OFF
REMOVE
2
Important Safety Information
FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M 11/20/15
Table of Contents
Use A Safety Chain
▲A safety chain will help control
drawn machinery should it
separate from the tractor drawbar.
▲Use a chain with the strength
rating equal to or greater than the
gross weight of the towed
machinery.
▲Attach the chain to the tractor
drawbar support or other specified
anchor location. Allow only
enough slack in the chain to
permit turning.
▲Do not use safety chain for towing.
These are common practices that may or may not be applicable to the products described in
this manual.
Use Safety
Lights and Devices
▲Slow moving tractors,
self-propelled equipment, and
towed implements can create a
hazard when driven on public
roads. They are difficult to see,
especially at night.
▲Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
▲Maximum transport speed for an
attached implement is 20 mph. DO
NOT EXCEED. Never travel at a
speed which does not allow
adequate control of steering and
stopping. Some rough terrains
require a slower speed.
▲As a guideline, use the following
maximum speed weight ratios for
an attached implement:
20 mph when weight of attached
implement is less than or equal to
the weight of machine towing the
implement.
10 mph when weight of attached
implement exceeds weight of
machine towing implement but
not more than double the weight.
▲IMPORTANT: Do not tow a load
that is more than double the weight
of the machine towing the load.
Transport
Machinery Safely
▲Comply with state and local laws.
▲Use towing vehicle and trailer of
adequate size and capacity.
▲Secure equipment towed on a
trailer with tie downs and chains.
▲Sudden braking can cause a trailer
to swerve and upset. Reduce
speed if trailer is not equipped with
brakes.
▲Avoid contact with any over head
utility lines or electrically charged
conductors.
▲Engage park brake when stopped
on an incline.
Practice Safe Maintenance
▲Understand procedure before doing
work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
▲Work in a clean dry area.
▲Lower attached implement to the
ground, put tractor in park, turn off
engine, and remove key before
performing maintenance.
▲Allow implement to cool before
working on it.
▲Disconnect battery ground cable (-)
before servicing or adjusting
electrical systems or before welding
on implement.
▲Do not grease or oil implement
while it is in operation.
▲Inspect all parts. Make certain
parts are in good condition &
installed properly.
▲Replace parts on this machine with
genuine Land Pride parts only. Do
not alter this machine in a way
which will adversely affect its
performance.
▲Remove buildup of grease, oil, or
debris.
▲Remove all tools and unused parts
from implement before operation.
3
Important Safety Information
11 / 2 0 / 15 FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M
Table of Contents
These are common practices that may or may not be applicable to the products described in
this manual.
Avoid High
Pressure Fluids Hazard
▲Escaping fluid under pressure can
penetrate the skin causing serious
injury.
▲Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.
▲Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
▲Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.
▲Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
▲DO NOT DELAY. If an accident
occurs, see a doctor familiar with
this type of injury immediately. Any
fluid injected into the skin or eyes
must be treated within
a few hours or
gangrene may
result.
Tire Safety
▲Tire changing can be dangerous
and should be preformed by
trained personnel using the
correct tools and equipment.
▲When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
▲When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
Prepare for Emergencies
▲Be prepared if a fire starts.
▲Keep a first aid kit and fire
extinguisher handy.
▲Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.
911
Keep Riders Off
Machinery
▲Never carry riders or use
machinery as a person lift.
▲Riders obstruct operator’s view.
▲Riders could be struck by foreign
objects or thrown from the
machine.
▲Never allow children to operate
equipment.
Wear
Protective Equipment
▲Wear protective clothing and
equipment appropriate for the job
such as safety shoes, safety
glasses, hard hat, and ear plugs.
▲Clothing should fit snug without
fringes and pull strings to avoid
entanglement with moving parts.
▲Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
▲Operating equipment safely
requires the operator’s full
attention. Avoid wearing radio
headphones while operating
machinery.
Use Seat Belt and ROPS
▲Operate only tractors equipped
with a Roll-Over Protective
Structure (ROPS) and seat belt.
▲Fasten seat belt snugly and
securely to help protect against
serious injury or death from falling
and tractor overturn.
▲Wear protective equipment such
as a hard hat, safety shoes, safety
glasses, and ear plugs.
4
Important Safety Information
FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M 11/20/15
Table of Contents
Safety Labels
Your Grooming Mower comes equipped with all safety labels in
place. They were designed to help you safely operate your
implement. Read and follow their directions.
1. Keep all safety labels clean and legible.
2. Refer to this section for proper label placement. Replace
all damaged or missing labels. Order new labels from your
nearest Land Pride dealer. To find your nearest dealer,
visit our dealer locator at www.landpride.com.
818-130C
Caution
818-540C
Danger: Guard Missing
FDR1660 & FDR1672
FDR1648
35784
20907
35785
13314
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
4. Refer to this section for proper label placement.
To install new labels:
a. Clean surface area where label is to be placed.
b. Spray soapy water onto the cleaned area.
c. Peel backing from label and press label firmly onto the
surface.
d. Squeeze out air bubbles with edge of a credit card or
with a similar type of straight edge.
858-095C
Red Reflector (Both Sides)
7
Important Safety Information
11 / 2 0 / 15 FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M
Table of Contents
FDR1660 & FDR1672
FDR1648
FDR1648, 1660 & FDR1672
35786
20906
35784
838-270C
Caution: V-Belt Installation
FDR1648, FDR1660 & FDR1672
818-142C
Caution: Rotating Drive Line
FDR1648, FDR1660 &
FDR1672
8
Introduction
FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M 11/20/15
Table of Contents
Land Pride welcomes you to the growing family of new
product owners.
This Grooming Mower has been designed with care and
built by skilled workers using quality materials. Proper
assembly, maintenance, and safe operating practices will
help you get years of satisfactory use from this machine.
Application
The Land Pride FDR16 Rear Discharge Grooming
mowers are designed and built to provide high
productivity and excellent cutting quality on well
maintained lawn and turf surfaces. These mowers are
adapted for category 1 attachment and operation on
15-30 hp compact utility tractors. They are offered with
48", 60", and 72" rear discharge cutting decks, which
makes them well suited to meet the mowing needs of
home and estate owners alike. These rear discharge
cutting decks will provide a superb quality of cut and
superior clipping distribution when grass is cut on a
frequent basis and ground conditions are not wet.
See “Specifications & Capacities” on page 27 and
“Features & Benefits” on page 28 for additional
information and performance enhancing options.
Using This Manual
•This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
•The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
•To order a new Operator’s or Parts Manual, contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge, from our website at
www.landpride.com.
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
IMPORTANT: A special point of information related
to the following topic. Land Pride’s intention is this
information must be read & noted before continuing.
NOTE: A special point of information that the
operator should be aware of before continuing.
Introduction
Owner Assistance
The Online Warranty Registration should be completed
by the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
The parts on your Grooming Mower have been specially
designed by Land Pride and should only be replaced with
genuine Land Pride parts. Contact a Land Pride dealer if
customer service or repair parts are required. Your Land
Pride dealer has trained personnel, repair parts, and
equipment needed to service the implement.
Serial Number
Refer to Figures 1A & 1B on page 9:
Model No. _____________Serial No. ______________
For quick reference and prompt service, record model
and serial number in the spaces provided above and
again on warranty page 31. Always provide model and
serial number when ordering parts and in all
correspondences with your Land Pride dealer. Refer to
Figures 1A & 1B on page 9 for location of your serial
number plate.
Further Assistance
Your dealer wants you to be satisfied with your new
Grooming Mower. If for any reason you do not
understand any part of this manual or are not satisfied
with the service received, the following actions are
suggested:
1. Discuss the matter with your dealership service
manager making sure that person is aware of any
problems you may have and has had the opportunity
to assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem, and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpservicedept@landpride.com
FDR16 Series mowers are covered under Patent Numbers: US
D445,432 S and US D424,071 S
10
Section 1: Assembly & Set-Up
FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M 11/20/15
Table of Contents
Section 1: Assembly & Set-Up
Tractor Requirements
Tractor horsepower rating should be between 15 & 30
PTO horsepower. Tractors outside this horsepower range
must not be used.
The rear power take-off (PTO) speed must be capable
540 RPM and have a 1 3/ 8"-6 spline.
A 3-Point Category I hitch is required. The lower 3-Point
arms must be stabilized to prevent side-to-side
movement. Most tractors have sway blocks or adjustable
chains for this purpose.
The tractor MUST be equipped with protective equipment
designed to shield the operator from thrown objects and
from tractor roll over. An enclosed tractor cab with a Roll
Over Protective Structure (ROPS) may qualify. See
tractor’s manual for type of protection your tractor has.
Torque Requirements
Refer to “Torque Values Chart” on page 30 to
determine correct torque values for common bolts.
Dealer Preparations
This Grooming Mower has been partially assembled at
the factory. Some assembly and preparation are still
required before the mower is ready for operation and can
be attached to the customer tractor.
Make sure that the intended tractor conforms to the
Tractor Requirements stated above. Also, read and
understand the Operator’s Manual for the Grooming
Mower. An understanding of how it works will aid in its’
assembly and setup.
Go through the Pre-Assembly Checklist before
assembling the mower. To speed up your assembly task
and make the job safer, have all needed parts and
equipment readily at hand.
Vented Dipstick Installation
Refer to Figure 1-1:
A vented dipstick for the gearbox is included in a bag with
the manual. See your nearest Land Pride dealer if
dipstick is missing. Remove temporary red plug from top
of splitter gearbox and replace with supplied dipstick.
NOTE: The tractor may need additional ballast to
maintain steering control. See tractor’s Operator’s
Manual to determine if additional ballast is required.
IMPORTANT: Grooming Mowers are shipped with
solid plugs in the gearboxes to prevent loss of oil
during shipping and handling. The solid plug on top
of the gearbox must be replaced with a vented
dipstick before operating the mower.
Installation of Vented Dipstick
Figure 1-1
Upper 3-Point Hitch Assembly
Refer to Figure 1-2 on page 11:
1. Remove angle shipping brackets (not shown) with
gauge wheel assemblies (#4) from mower frame.
2. Remove rear hitch braces (#1), A-Frame hitch braces
(#2), and clevis hitches (#3) from shipping crate.
3. Attach rear hitch braces (#1) to hole “A1” inside of
rear hitch mounting plates (#5) with 5/8" bolts and
flanged lock nuts (#6) provided in rear hitch plates.
Do not tighten nuts.
4. Attach A-Frame hitch braces (#2) to holes “A2” inside
front hitch mounting plates (#7) with 5/8" bolts and
flanged lock nuts (#8) provided in front hitch plates.
Do not tighten nuts.
5. Remove 5/8" x 5 1/2" lg. bolt, lock washer, and
nut (#11) from upper pivoting hitch (#9). Don’t let
spacer tube (#10) fall from upper pivoting hitch.
Pre-Assembly Checklist
Check Reference
Make sure miscellaneous assembly tools are on hand: Hammer,
tape measure, hacksaw, assortment of wrenches & sockets,
3/8" drill, drill bits and spirit level.
Have a forklift or hoist with properly sized chains and safety
stands on hand capable of lifting 2500 lbs.
Have a minimum of two people available during assembly.
Check to see if auxiliary tractor weights are needed.
See Specifications on page 27 for mower weights.
Make sure all major components and loose parts
are shipped with the machine.
Operator’s
Manual
Double check to make sure all fasteners & pins are
installed in the correct location. Refer to the Parts
Manual if unsure.
NOTE: All assembled hardware from the factory
has been installed in the correct location.
Remember location of a part or fastener if
removed. Keep parts separated.
Operator’s
Manual &
Parts Manual
Make sure working parts move freely, bolts are
tight & cotter pins are spread.
Operator’s
Manual
Make sure all grease fittings are in place and
lubricated.
Section 5
Page 25
Make sure all safety labels are correctly located
and legible. Replace if damaged.
Important
Safety
Information
Make sure all red reflectors are correctly located
and visible when machine is in transport position.
Page 4
30216
DO NOT
OVERFILL!
Oil Level
Plug
Solid
Red Plug
Vented Dip-
11
Section 1: Assembly & Set-Up
11 / 2 0 / 15 FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M
Table of Contents
Hitch And Gauge Wheel Assemblies
Figure 1-2
20828
Widest side of clevis is
located away from hitch
plates (#7).
6. Swing A-frame hitch braces (#2) up to a vertical
position. Raise rear hitch braces (#1) up and outside
of A-Frame hitch braces as shown.
7. Position upper pivoting hitch (#9) with hook (#20)
hanging down as shown. Assemble upper pivoting
hitch (#9) and spacer tube (#10) in-between A-frame
hitch braces (#2) with existing bolt, lock washer, and
hex nut (#11).
8. Tighten 5/8"-18 GR5 bolt (#11) to the correct torque.
9. Tighten 5/8"-11 GR8 bolts (#6 & #8) to the correct
torque.
Gauge Wheel Assembly
Refer to Figure 1-2:
1. Remove factory bolts from top of gauge wheel
spindles (#4).
2. Remove gauge wheels (#4) from angle shipping
brackets. Keep spacers (#12 & #13) with their
respective gauge wheels. Discard shipping brackets.
3. Insert gauge wheel yoke spindles (#4) into gauge
wheel arms (#14) with three 1" spacers (#12) below
each arm. Install remaining spacers (#12 & #13)
above each arm.
4. Remove linchpins (#21) from clevis hitch pin (#1).
Secure gauge wheels (#4) to gauge wheel
arms (#14) with linchpins (#21).
Lower 3-Point Clevis Hitch Assembly
Refer to Figure 1-2:
1. Attach lower right-hand clevis hitch (#3) outside of
right-hand mounting plate (#7) as follows:
a. Insert 5/8" x 1 3/4" bolt (#15), through SAE
standard washer (#17), clevis hitch hole “A”, hitch
plate (#7), and SAE standard washer (#17).
b. Secure bolt (#15) with hex top lock nut (#19). Draw
hex top lock nut (#19) up snug and then back off 1/
2 turn to allow clevis hitch (#3) to pivot.
c. Insert 5/8" x 1 3/4" bolts (#16) through SAE
standard washers (#17), clevis hitch hole “B”, slot
in hitch plate (#7), and USS large washer (#18).
d. Secure bolt (#16) with hex top lock nut (#19). Draw
hex top lock nut (#19) up snug and then back off 1/
2 turn to allow clevis hitch (#3) to pivot.
2. Repeat step 1 for the lower left-hand clevis hitch (#3).
NOTE: The 3-Point hitch system is designed for
front to back flotation when mowing on uneven
terrain. Additional field flotation and/or tractor
clarence can be obtained by mounting clevis
hitches (#3) in hole “B” or “C”. Rear brace
bars (#1) may need to be moved to holes “B1”.
12
Section 1: Assembly & Set-Up
FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M 11/20/15
Table of Contents
Tractor 3-Point Hook-up
!DANGER
A Crushing Hazard exists when hooking-up equipment to a
tractor. Do not allow anyone to stand between tractor and
implement while backing-up to implement. Do not operate
hydraulic 3-Point lift controls while someone is directly
behind the tractor or near the implement.
!DANGER
Always set tractor transmission in park, engage park brake,
shut tractor engine off and remove switch key before allowing
anyone including the operator to hook-up and unhook the
Grooming Mower from the tractor.
Refer to Figure 1-3:
1. Ensure lower arms are stabilized to prevent
excessive side movement. Most tractors have sway
blocks or adjustable chains for this purpose.
2. Be certain tractor draw bar will not interfere. Move
draw bar ahead or remove if required. Draw bar
should also be checked for clearance when unit is
being raised for the first time with driveline installed.
3. Slowly back tractor up to the Grooming Mower while
using 3-Point hydraulic control to align hitch holes in
3-Point lower lift arms with holes in hitch clevis (#2).
4. Engage tractor park brake, shut engine off, and
remove key before dismounting from tractor.
NOTE: Land Pride’s Quick Hitch can be attached to
the tractor to provide quick and easy 3-point hook-
up and detachment. See your nearest Land Pride
dealer to purchase a Quick-Hitch.
5. Insert lower hitch pins (#1) through hitch clevis holes
and lower lift arm holes. Secure hitch pins with
linchpins (#5).
6. Attach the tractor’s top center link to the mower’s
upper floating hitch (#4) with hitch pin (#6). Secure
hitch pin with hairpin cotter (#7).
Tractor Hook-up
Figure 1-4
Top Center Link Adjustment
Refer to Figure 1-4:
1. Adjust lower clevises in or out when additional
flotation is needed or when tractor interferes with
mower frame. See “Lower 3-Point Clevis Hitch
Assembly” on page 11 for adjustment instructions.
2. Start tractor and raise mower until gauge wheels are
off the ground. Slowly lower mower until gauge
wheels start to touch the ground. Continue to lower
mower until 3-Point clevises are level with the
ground. Set tractor 3-Point stop at this height to hold
the clevises level.
VERTICAL
UPPER HITCH PIN
LOWER HITCH PIN
3-POINT CLEVIS
20829
Tractor 3-Point Hitch
Figure 1-3
37298 35789
LONG CONE SHIELD
SHORT CONE SHIELD
13
Section 1: Assembly & Set-Up
11 / 2 0 / 15 FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M
Table of Contents
3. Lower lift arms should be an equal distance off the
ground. If they are not, adjust one of the arms until
they are both an equal distance off the ground and
3-Point clevis are both level with the ground.
4. To allow for mower flotation, adjust tractor top center
link in or out until upper hitch pin is vertically above
lower hitch pins as shown in Figure 1-4.
5. Mower top link has 2 holes in it to adjust to tractor’s lift
capabilities. Choose the hole that enables the tractor
to raise the mower to your desired height during
transport.
Quick Hitch Hook-Up
Figure 1-5
Quick Hitch Hook-up
Refer to Figure 1-5:
1. Attach lower 3-Point hitch clevis (#1) to the two upper
holes “A” and “B” above floating slots. The position of
the lower 3-Point hitch clevis depends on the tractor
and tractor tires.
2. Attach the rear braces (#2) as follows:
a. If lower hitch clevis (#1) holes “A” and “B” are
attached to the deck, attach rear braces (#2) to
hole “E”.
b. If lower hitch clevis (#1) holes “B” and “C” are
attached to the deck, attach rear braces (#2) to
hole “F”.
c. If lower hitch clevis (#1) holes “C” and “D” are
attached to the deck, attach rear braces (#2) to
hole “G”
3. See Quick Hitch manual in order to attach Quick
Hitch to lower 3-Point arms and top link.
39036
NOTE: This will lock the lower 3-Point arms into
position. Use 3-Point tractor float instead.
Driveline Hook-up to Gearbox
Refer to Figure 1-3 on page 12:
1. Check to make certain PTO is disengaged.
2. Park tractor and mower on a level solid surface and
place gear selector in park or in neutral and set park
brake.
3. Slowly engage 3-Point lift lever to raise mower until
gearbox shaft is in line (level) with tractor PTO shaft.
4. Support mower deck at this height with support jacks
or blocks to keep mower from drifting down.
5. Shut tractor engine off and remove switch key.
6. Remove and discard gearbox shaft protector (#9).
7. Before installing driveline, apply a liberal amount of all
purpose grease to both the tractor PTO shaft and
gearbox shaft (#9) to ease removal at a later time.
8. Slide universal joint of inner driveline with long cone
shield (#11) over mower gearbox shaft (#9). Secure
driveline with yoke locking device.
IMPORTANT: The tractor’s PTO shaft and mower
gearbox shaft must be aligned and level with each
other during installation of driveline. This alignment
is the shortest distance between the two shafts.
14
Section 1: Assembly & Set-Up
FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M 11/20/15
Table of Contents
Driveline Hook-up to Tractor
!DANGER
Do not engage tractor PTO while hooking-up and unhooking
driveline or while someone is standing near the driveline. A
person’s body and/or clothing can become entangled in the
driveline resulting in serious injury or death.
!DANGER
All guards and shields must be installed and in good working
condition at all times during mower operation!
!WARNING
Do not over speed PTO or mower damage may result. Some
tractors are equipped with multispeed PTO ranges. Be certain
your tractor’s PTO is set for 540 rpm.
!WARNING
Do not use a PTO adapter. A PTO adapter will increase strain
on the tractor’s PTO shaft resulting in possible damage to
shaft and driveline. It will also defeat the purpose of the
tractor’s master shield and could cause bodily injury or death.
!WARNING
Always disengage PTO, place tractor in park or set park
brake, shut tractor engine off, remove switch key, and wait for
blades to come to a complete stop before dismounting from
tractor to make adjustments!
Refer to Figure 1-3 on page 12:
1. Pull outer driveline (#10) and inner driveline (#11)
apart. Apply multi-purpose grease to inside of outer
profile and reassemble the two profiles.
2. Pull back on pull collar (#3) and hold while starting to
slide the universal joint onto the tractor’s PTO shaft.
3. Once driveline starts onto the PTO shaft, release pull
collar and continue to slide universal joint on until pull
collar releases and locks universal joint to the
tractor’s PTO shaft.
4. Push and pull on yokes at both ends of driveline to
make certain they are securely fastened to tractor
PTO shaft and mower gearbox shaft.
IMPORTANT: An additional driveline may be
required if mower is to be used on more than one
tractor, especially if a Quick Hitch is used.
IMPORTANT: The driveline must be lubricated
before putting it into service. Refer to “Lubrication”
on page 25.
NOTE: See “Shorten Driveline” if driveline is too
long and will not go onto the tractor’s PTO shaft.
Check Collapsible Length
Figure 1-6
Check Driveline Collapsible Length
Refer to Figure 1-6:
1. Make sure driveline is installed properly to the mower
gearbox input shaft and tractor PTO shaft before
checking driveline collapsed length. Refer to
“Driveline Hook-up to Gearbox” and “Driveline
Hook-up to Tractor” on page 14.
2. With driveline level, measure 1" (“B” dimension)
back from universal joint shield to end of outer
driveline shield as shown in Figure 1-6.
a. If measurement is less than 1", shorten driveline.
a. If measurement is 1" or more, skip to “Check
Maximum Allowable Length” on page 15.
Shorten Driveline
Refer to Figure 1-6:
1. Unhook driveline from tractor PTO shaft and gearbox
shaft.
2. Raise 3-Point arms until mower gearbox shaft and
tractor PTO shaft are approximately level with each
other.
3. Support mower deck at this height with support jacks
or support blocks to keep PTO and gearbox shafts
level while shorting the driveline.
4. Place gear selector in park, set park brake, shut
tractor off and remove switch key.
5. Pull driveline apart as shown in Figure 1-6.
6. Attach outer driveline universal joint to tractor PTO
shaft and inner driveline universal joint to mower
gearbox shaft. Pull on each driveline section to be
sure universal joints are properly secured.
22009
IMPORTANT: A driveline that is too long can bottom
out causing structural damage to tractor and mower.
Always check driveline collapsed length during initial
setup, when connecting to a different tractor, and
when alternating between using a Quick Hitch and a
standard 3-Point hitch. More than one driveline may
be required to fit all applications.
15
Section 1: Assembly & Set-Up
11 / 2 0 / 15 FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M
Table of Contents
7. Hold driveline sections parallel to each other. The
inner and outer shields on each section should end
approximately 1" short of reaching universal joint
shield on the adjacent section (see “B” dimensions).
8. If driveline sections are too long, measure 1"
(“B” dimension) back from universal joint shield and
make a mark at this location on the inner and outer
driveline shields.
9. Cut-off inner driveline shield at measured mark
(“X” dimension). Cut same amount off inner driveline
profile (“X1” dimension).
10. Repeat cut-off procedure (“Y” & “Y1” dimensions) on
the outer driveline section.
b. Remove all burrs and cuttings.
Check Maximum Allowable Length
Figure 1-7
Check Maximum Allowable Length
Refer to Figure 1-7:
Make sure driveline collapsible length is checked first.
See “Check Driveline Collapsible Length” on page 14.
Driveline maximum allowable length, when fully
extended, must have a minimum overlap of profile tubes
by not less than 1/2 the free length with both inner and
outer profile tubes being of equal length. Determine the
maximum allowable length as follows:
1. Unhook driveline from tractor and Grooming Mower.
Pull outer and inner drivelines apart.
2. Measure and record “Free Length” of inner and
outer profiles as shown in Figure 1-7.
3. Move driveline halves together until profile tubes
overlap by 1/2 the “Free Length”. For future reference,
measure and record “Maximum Allowable Length”
as shown in Figure 1-7.
Record Maximum Allowable Length here: ________
4. Reattach inner driveline yoke to gearbox shaft and
outer driveline yoke to tractor's PTO shaft.
5. The driveline should now be moved back and forth to
ensure that both ends are secured. Reattach any end
that is loose.
24804
Outer Shielding has been removed for clarity.
!WARNING
Always make certain driveline yokes are secured to the tractor
PTO shaft and mower drive shaft before engaging PTO. A
loose driveline can slips off the end of a connected shaft while
rotating and cause serious bodily injury or death.
Maximum PTO driveline Movement During Operation
Figure 1-8
Check Driveline Interference
!WARNING
Do not operate mower in the raised position. Lifting the
mower too high with driveline engaged can damage the
driveline and throw flying projectiles causing serious bodily
injury or death.
Refer to Figure 1-8:
1. Start tractor and raise Grooming Mower just enough
to remove support blocks.
2. Return to the tractor and slowly engage tractor
hydraulic 3-Point control lever to raise and lower
mower while checking for sufficient drawbar
clearance. Move drawbar ahead, aside, or remove if
required.
3. Raise and lower implement to find maximum
extended driveline length. Check to make certain
driveline overall length does not exceed maximum
recorded length in step 3 under “Check Maximum
Allowable Length” on page 15.
4. If needed, set tractor 3-Point lift height to keep
driveline from exceeding maximum allowable length.
24872
16
Section 2: Accessories & Set-up
FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M 11/20/15
Table of Contents
Front Roller Assembly
(FDR1648, FDR1660, and FDR1672)
Refer to Figure 2-1:
1. Assemble brackets (#2) and (#3) to deck with
carriage bolts (#4) and flange nuts (#5).
2. Insert roller (#8) between brackets and install pin
(#1) through brackets and roller. Secure with
washer (#6) and cotter pin (#7).
.
Front Roller Assembly
Figure 2-1
20563
Cutting Blades
There are four blade choices to select from based upon
soil condition, density of grass, and tractor horsepower.
The appearance of the finish cut may vary between low
lift and high lift blades. See your Land Pride dealer for
blade availability.
Low Lift Blades
Land Pride’s low lift blades are designed for mowing over
sandy soil terrain where high suction lift is not crucial.
Sand sucked into the blades accelerates blade wear
more than normal. Low lift blades are recommended
because they produce a lower suction keeping sand uplift
and blade wear to a minimum.
Medium Lift Blades (Factory Standard)
Land Pride’s medium lift blades are great when
horsepower is a concern. They produce a medium
suction to lift grass and require less horsepower than
high lift blades.
High Lift Blades
Land Pride’s high lift blades develop the greatest suction
for lifting grass for that fresh clean cut look. However,
they may require more horsepower especially when
cutting tall dense grass. They are not recommended for
sandy soil conditions.
Mulching Blades
Land Pride’s mulching blades are designed to chop
leaves and/or grass into smaller parts leaving your lawn
looking fresher and cleaner than ever before.
Accessory Part Numbers
See your Land Pride dealer for blade availability.
Land Pride Part Numbers & Descriptions
Part No. Part Description
Front Roller Assembly
315-516S FDR1648, FDR1660 & FDR1672
Low Lift Blade (3 blades required per mower)
890-323C FDR1648
890-204C FDR1660
890-200C FDR1672
Medium Lift Blade (3 blades required per mower)
890-325C FDR1648
890-375C FDR1660
890-318C FDR1672
High Lift Blade (3 blades required per mower)
890-219C FDR1648
890-171C FDR1660
890-172C FDR1672
Mulching Blade (3 blades required per mower)
890-700C FDR1648
890-702C FDR1660
890-698C FDR1672
Section 2: Accessories & Set-up
17
Section 3: Operating Instructions
11 / 2 0 / 15 FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M
Table of Contents
Inspection Procedures
!DANGER
Do not engage tractor PTO while hooking-up and unhooking
driveline or while someone is standing near the driveline. A
person’s body and/or clothing can become entangled in the
driveline resulting in serious injury or death.
!WARNING
Always disengage PTO, place tractor in park or set park
brake, shut tractor engine off, remove switch key, and wait for
blades to stop rotating before dismounting from tractor!
1. Park tractor and mower on a level surface.
2. Make sure tractor PTO is disengaged and mower
blades have come to a complete stop.
3. Inspect tractor safety equipment to make sure it is in
good working condition.
4. Carefully raise and lower implement to ensure
drawbar, tires, and other equipment on the tractor do
not contact the mower or driveline.
5. With PTO disengaged and driveline completely
stopped, check mower blades for sharpness. See
“Service Mowing Blades” on page 22.
The remaining inspections are made by engaging the
PTO to check for normal operation.
!DANGER
All guards and shields must be installed and in good working
condition at all times during mower operation!
!WARNING
Do not over speed PTO or mower damage may result. Some
tractors are equipped with multispeed PTO ranges. Be certain
your tractor’s PTO is set for 540 rpm.
6. Start tractor, set throttle to an idle or slightly above
idle and slowly engage PTO. Initial start-up vibration
is normal and should stop after a few revolutions.
Stop PTO rotation immediately if vibration continues.
7. Once mower is running smoothly, increase tractor
PTO speed to the appropriate rpm. Stop PTO rotation
immediately if vibration occurs.
8. Investigate the cause of vibration. Make necessary
corrections before continuing.
IMPORTANT: Stop PTO rotation immediately if
vibration occurs during start-up or thereafter. Follow
all tractor shut down procedures before dismounting
from tractor. Investigate cause. Make necessary
repairs and adjustments before continuing.
Section 3: Operating Instructions
Operating Check
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the Grooming Mower. Therefore, it is
absolutely essential that no one operates the mower
without first having read, fully understood, and become
totally familiar with the Operator’s Manual. Make sure the
operator has paid particular attention to:
•Important Safety Information, page 1
•Section 1: Assembly & Set-Up, page 10
•Section 2: Accessories & Set-up, page 16
•Section 4: Adjustments, page 21
•Section 3: Operating Instructions, page 17
•Section 5: Maintenance & Lubrication, page 22
Pre-Start Checklist
Make sure the operator has completed the “Operating
Checklist” below.
Tractor Shut Down Procedure
It is essential that the tractor be shut down as noted
below before making any inspections, maintenance
and/or repairs to the tractor and/or mower.
1. Park tractor on a level surface. Don’t work under or
around an implement parked on a steep incline.
2. Disengage PTO if operating.
3. Place tractor in park and set park brake, shut tractor
off and remove switch key. Wait for PTO to come to a
complete stop before dismounting tractor.
4. Wear safety glasses to make inspections and
perform maintenance.
Operating Checklist
✔Check Page
Read and follow all safety information carefully.
Refer to “Important Safety Information”. Page 1
Read and follow hook-up & preparation
instructions. Refer to “Assembly & Set-up”.Page 10
Make sure all guards and shields are in place and
in good working condition.
Make all necessary adjustments.
Refer to section on “Adjustments”.Page 21
Read and follow all maintenance instructions.
Refer to “Maintenance & Lubrication”.Page 22
Lubricate mower as required. Refer to
“Lubrication”. Page 25.
Check oil level in gearbox. Make certain all oil
plugs are properly replaced. Refer to “Gearbox”. Page 26
Check mower initially and periodically for loose
bolts and pins. Be sure all nuts and bolts are
tight. Especially make sure mower blade
bolts are tight. Refer to “Torque Values Chart
for Common Bolt Sizes”.
Page 30
18
Section 3: Operating Instructions
FDR1648, FDR1660 & FDR1672 Rear Discharge Grooming Mowers 310-366M 11/20/15
Table of Contents
Transporting
!WARNING
When traveling on public roads, use accessory lights, SMV
sign, clean reflectors, and other adequate devices to warn
operators in other vehicles of your presence. Always comply
with all federal, state, and local laws.
!WARNING
Do not exceed maximum transport speed of 20 MPH with
mower attached. Travel below 20 MPH on rough terrain. The
mower can lose a tire or tires can break apart causing the
operator to lose control of tractor and/or implement.
1. When raising mower to transport position, be sure
driveline does not contact tractor or mower. Adjust
and set tractor’s 3-Point hitch lift height so that the
PTO shaft does not contact mower deck in the fully
raised position.
2. Be sure to reduce tractor ground speed when turning
and leave enough clearance so the mower does not
contact obstacles such as buildings, trees, or fences.
3. Select a safe ground speed when transporting from
one area to another.
4. When traveling on roadways, transport in such a way
that faster moving vehicles may pass you safely. A
slow moving vehicle sign should always be properly
displayed when traveling on public roads or right-of-
ways.
5. Shift tractor to a lower gear when traveling over rough
or hilly terrain.
Safety Information
!DANGER
Keep others away from the mower while it is operating.
Grooming Mowers have the ability to discharge objects at
high speeds causing serious injury or death. Stop blade
rotation if bystanders are nearby!
!DANGER
Tractor PTO shield, Gearbox shaft shield and driveline
shields must be secured in place when operating mower to
avoid injury or death from entanglement in driveline!
!DANGER
Do not operate mower with a bent or broken driveline. Such a
driveline can break apart while rotating at high speeds
causing serious injury or death. Always remove mower from
service until damaged driveline is repaired or replaced.
NOTE: Always disengage PTO before raising mower
to transport position.
!DANGER
Do not engage tractor PTO while hooking-up and unhooking
driveline or while someone is standing near the driveline. A
person’s body and/or clothing can become entangled in the
driveline resulting in serious injury or death.
!DANGER
Always disconnect main driveline from tractor PTO before
servicing underside of mower. PTO can be engaged if tractor
is started causing mower damage, bodily injury or death.
!DANGER
All V-belt guards must be in good working condition and
installed before PTO is engaged. Never allow fingers, hands,
or other body extremities to come near a moving V-belt or
pulley. Doing so can result in server bodily injury or death.
!DANGER
Never place hands or feet under the deck or attempt to make
adjustments to the mower with PTO engaged. Mower blades
rotating at high speeds cannot be seen and are located close
to the deck housing. Body extremities can be cut off instantly.
!DANGER
Never allow riders including children on the tractor or mower.
They can fall and be ran over, become entangled in rotating
components, and/or pinched by moving components causing
serious injury or death.
!DANGER
Do not operate on or travel across steep inclines where a
tractor or mower could roll-over resulting in serious injury or
death. Consult your tractor’s manual for acceptable inclines
the tractor is capable of traveling across.
!DANGER
Clear area to be cut of debris and unforeseen removable
objects before mowing. Mark any potential hazards that
cannot be removed such as dirt mounds, tree stumps, posts,
large rocks, holes, and drop-offs with a visible flag.
!DANGER
Always disengage PTO before lifting mower up and never
operate mower in the raised position. The mower can
discharge objects at high speeds resulting in injury or death.
!DANGER
Do not use mower as a working platform. The mower is not
properly designed or guarded for this use. Using mower as a
working platform can cause serious injury or death.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
