Motorola PROFILE 300 Owner's manual

Cellular

Telephone

Owners

Manual

WELCOME

Thank you for selecting Motorola—a world leader in

cellular technology.

All Motorola cellular phones are designed and manufactured in the

United States to meet Motorola’s exacting speciﬁcations and world

class quality standards. This phone is no exception. This personal

phone withstands our rigorous durability tests including tempera-

ture, humidity, shock, dust, vibration, and a drop test.

Product superiority is yours!

• For any information about your product or accessories for your

product, please call Motorola at: 1-800-331-6456, 1-800-461-

4575 (Canada).

• For any information about your cellular service, please call your

service provider (Carrier).

Carrier’s Name___________________________________________

Carrier’s Phone Number___________________________________

• You will need to have the following information when you

inquire about your phone or service. This information is located

on the back of your telephone after you remove the battery.

ESN Number_____________________________________________

MSN Number ____________________________________________

Model Number___________________________________________

Cellular Phone Number ___________________________________

• Unlock Code—The sequential code of 1, 2, 3 is the standard

unlock code programmed into all phones by the factory. It is

often changed to the last three digits of your cellular phone num-

ber by the Carrier. For easy access to this unlock code in the

future, please list it here now:__________. (Please contact your

place of purchase if your unlock code has been changed and

you do not have this information.)

Warranty Expiration Date__________________________________

Date of Purchase _________________________________________

2

WELCOME

TABLE OF CONTENTS

GENERAL SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . 6

INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

PHONE OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Preparing Battery for Initial Use . . . . . . . . . . . . . . . . . . . . . 12

Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Removing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Quick Change Method . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Turn Phone On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Placing a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Automatic Redialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Call in Absence Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 18

Signal Strength Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Displaying Battery Voltage Meter. . . . . . . . . . . . . . . . . . . . 19

Low Battery Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Adjusting Earpiece Volume . . . . . . . . . . . . . . . . . . . . . . . . 20

Adjusting Ringer Volume. . . . . . . . . . . . . . . . . . . . . . . . . . 20

Volume Meter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Muting Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Displaying Own Phone Number . . . . . . . . . . . . . . . . . . . . 20

Two-System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Illuminated Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Antenna System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

MEMORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Storing Numbers to a Memory Location. . . . . . . . . . . . . . . 22

Memory Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Changing Entries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3

TABLE OF CONTENTS

Clearing Entries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Recalling from Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Memory Scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Recalling Last Number Called . . . . . . . . . . . . . . . . . . . . . . 24

Recalling Area Code / Preﬁx (Postscripting) . . . . . . . . . . . . 24

Turbo Dial™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

One-Touch Emergency Dialing . . . . . . . . . . . . . . . . . . . . . 25

Super Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Scratch Pad Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Tone Dialing (Two-Part Calling) . . . . . . . . . . . . . . . . . . . . . 26

Pause Dialing (Memory Linking) . . . . . . . . . . . . . . . . . . . . 26

Placing a Linked Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

To Enable/Disable a Speciﬁc Feature . . . . . . . . . . . . . . . . . 29

Distinctive Ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Automatic Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Multiple Key Answer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Automatic Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

One-Touch Emergency Dialing . . . . . . . . . . . . . . . . . . . . . 32

VOX Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Reminder Beeps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

PIN Code Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Feature Status Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

TIMERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Individual Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Resettable Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Cumulative Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

One Minute Beep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4

TABLE OF CONTENTS

SECURITY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Electronic Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Displaying Unlock Code . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Changing Unlock Code. . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Automatic Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Outgoing Call Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . 38

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Chargers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Ultra Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Travel Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . . . . . . 44

ROAMING AND SYSTEM OPERATION. . . . . . . . . . . . . . . 47

Service Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Weak Signal Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Roaming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Selectable System Registration. . . . . . . . . . . . . . . . . . . . . . 48

Changing System Type . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

C Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

BEFORE CALLING FOR SERVICE . . . . . . . . . . . . . . . . . . . 51

MESSAGE GLOSSARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

PATENT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . 60

QUICK REFERENCE SECTION. . . . . . . . . . . . . . . . . . . . . . 61

5

GENERAL SAFETY INFORMATION

IMPORTANT

Read This Information Before Using Your

Hand-held Portable Cellular Telephone

First introduced in 1984, the hand-held portable cellular telephone

is one of the most exciting and innovative electronic products ever

developed. With it, you can stay in contact with your office, your

home, emergency services, and others.

For the safe and efficient operation of your phone, observe

these guidelines.

Your cellular telephone is a radio transmitter and receiver. When it

is ON, it receives and also sends out radio frequency (RF) energy.

The phone operates in the frequency range of 824 MHz to 894

MHz and employs commonly used frequency modulation (FM)

techniques. When you use your phone, the cellular system

handling your call controls the power level at which your phone

transmits. The power level can range from 0.006 of a watt to 0.6

of a watt.

Exposure to Radio Frequency Energy

In 1991, the Institute of Electrical and Electronics Engineers (IEEE),

and in 1992, the American National Standards Institute (ANSI),

updated the 1982 ANSI Standard for safety levels with respect to

human exposure in RF energy. Over 120 scientists, engineers, and

physicians from universities, government health agencies, and

industry, after reviewing the available body of research, developed

this updated Standard. In March 1993, the Federal

Communications Commission (FCC) proposed the adoption of this

updated Standard.

The design of your phone complies with this updated Standard. If

you want to limit RF exposure even further, you may choose to con-

trol the duration of your calls and operate your phone in the most

power efficient manner.

Efficient Phone Operation

For your phone to operate at the lowest power level consistent with

satisfactory call quality. Please observe the following guidelines.

If your phone has an extendable antenna, extend it fully. Some

models allow you to place a call with the antenna retracted.

However, your phone operates more efficiently with the antenna

fully extended.

Hold the phone as you would any other telephone. While speak-

ing directly into the mouthpiece, position the antenna up and over

your shoulder.

6

GENERAL SAFETY INFORMATION

Do not hold the antenna when the phone is in use. Holding the

antenna affects call quality and may cause the phone to operate at

a higher power level than needed.

Antenna Care and Replacement

Do not use the phone with a damaged antenna. If a damaged

antenna comes into contact with the skin a minor burn may result.

Replace a damaged antenna immediately. Take your phone to a

qualiﬁed service center for repair.

Use only the supplied or approved antenna. Non-approved anten-

nas, modiﬁcations, or attachments could impair call quality, dam-

age the phone and violate FCC regulations.

Driving

Check the laws and regulations on the use of cellular telephones in

the areas where you drive. Always obey them. Also, when using

your phone while driving, please:

• Give full attention to driving,

• Use hands-free operation, if available, and

• Pull off the road and park before making or answering a call if

driving conditions so require.

Electronic Devices

Most modern electric equipment—for example equipment in hos-

pitals and cars—is shielded from RF energy. However, RF energy

from cellular telephones may affect malfunctioning or improperly

shielded electronic equipment.

RF energy may affect improperly installed or inadequately shielded

electronic operating and entertainment systems in motor vehicles.

Check with the manufacturer or its representative to determine if

these systems are adequately shielded from external RF energy. You

should also check with the manufacturer of any equipment that has

been added to your vehicle.

Consult the manufacturer of any personal medical devices (such as

pacemakers, hearing aids, etc.) to determine if they are adequately

shielded from external RF energy.

Turn your phone OFF in health care facilities when any regulations

posted in the areas instruct you to do so. Hospitals or health care

facilities may be using remote RF monitoring equipment.

Aircraft

Turn your phone OFF before boarding any aircraft.

• Use it on the ground only with crew permission.

• Do not use in the air.

7

GENERAL SAFETY INFORMATION

To prevent possible interference with aircraft systems, Federal

Aviation Administration (FAA) regulations require you to have per-

mission from a crew member to use your phone while the plane is

on the ground. To prevent interference with cellular systems, FCC

regulations prohibit using your phone while the plane is in the air.

Children

Do not allow children to play with your phone. It is not a toy.

Children could hurt themselves or others (by poking themselves or

others in the eye with the antenna, for example). Children also

could damage the phone, or make calls that increase your tele-

phone bills.

Blasting Areas

To avoid interfering with blasting operations, turn your unit OFF

when in a blasting area or in areas posted:

“Turn off two-way

radio”. Construction crews often use remote control RF devices to

set off explosives.

Potentially Explosive Atmospheres

Turn your phone OFF when in any area with a potentially explosive

atmosphere. It is rare, but your phone or its accessories could gener-

ate sparks. Sparks in such areas could cause an explosion or ﬁre

resulting in bodily injury or even death.

Areas with a potentially explosive atmosphere are often, but not

always, clearly marked. They include: fueling areas such as gas sta-

tions, below deck on boats, fuel or chemical transfer or storage facil-

ities, and areas where the air contains chemicals or particles, such as

grain, dust, or metal powders, and any other areas where you would

normally be advised to turn off your vehicle engine.

Do not transport or store ﬂammable gas, liquid, or explosives in the com-

partment of your vehicle which contains your phone or accessories.

Vehicles powered by liqueﬁed petroleum gas (such as propane or

butane) must comply with the National Fire Protection Standard

(NFPA-58). For a copy of this standard, contact the National Fire

Protection Association, One Batterymarch Park, Quincy, MA 02269,

Attn: Publications Sales Division.

Magnetic Storage Media

Your phone contains a magnet. Do not place your phone in close

proximity to magnetic storage media such as diskettes or credit cards

for extended periods of time.

Batteries

CAUTION: To prevent injuries or burns, do not allow metal objects

to contact or short circuit the battery terminals.

8

GENERAL SAFETY INFORMATION

The design of Motorola’s cellular telephone complies with all applic-

able RF Safety Standards.

Motorola meets the standards and recommendations for the protec-

tion of public exposure to RF electromagnetic energy established by

governmental bodies and other qualiﬁed organizations, such as the

following:

• National Council on Radiation Protection and Measurements

(NCRP). Report 86.

• Department of Health and Welfare Canada Safety Code 6.

• Verband Deutscher Elektroigenieure (VDE) DIN-0848.

• Directives of the European Community, Directorate General V in

Matters of Radio Frequency Electromagnetic Energy.

• National Radiological Protection Board of the United Kingdom.

GS-11, 1988.

• American National Standards Institute (ANSI)/IEEE

C95.1-1992.2.

INTRODUCTION

This phone represents the state-of-the-art in personal cellular tele-

phones today. The listing below shows just a few of the exceptional

features that this telephone contains:

• Signal Strength Meter • Turbo Dialing

• Battery Meter • Auto Answer

• One-Touch Emergency Dialing • Call Timers

• 9 Selectable Ringer Styles • Memory Protect

• Multiple Key Answer

Remember, these are just a few of the great features that your phone

provides to meet your business and personal needs. In addition, a num-

ber of accessory options are available to help you tailor your cellular

system to your individual preferences. These include a 3-Watt Booster

or an Ultra Saver that plugs into the vehicle’s cigarette lighter to con-

serve the telephone’s battery.

To help you become familiar with your telephone’s features, we suggest

you experiment with them as you progress through this manual.

Please read the General Safety Information beginning on page 6 before

operating the unit.

9

INTRODUCTION

10

PHONE OVERVIEW

888

8888888

1

2

3

6

5

8

4

7

5

PHONE OVERVIEW

1 Retractable Antenna — Extend for optimum performance.

2 Earpiece

3 Status Indicators — Flash or light steadily to alert you to a

number of conditions:

IU

(In Use)

— Flashes while a call is in process.

RM (Roam) — Flashes if phone is accessing a service area out-

side of your home system.

NS

(No Service)

— Flashes or lights steadily if the phone is

beyond the range of a cellular system. While lit, calls cannot

be placed or received (See Service Area, page 47).

Signal Strength Indicator — Flashes the relative strength of the

signal received by the phone.

Battery Strength Indicator — Lights steadily to indicate the

estimated remaining capacity of the battery (See Displaying

Battery Voltage Meter, page 19).

4 Number Display — Displays phone number, memory location

number , or message. Some information will require viewing

sequentially displayed messages.

5 Function Keys

‰ Recalls and displays numbers stored in memory.

Ø Stores numbers in memory.

Ç Clears digits from the display. Press and hold to clear

entire display at once.

Ï Used in conjunction with other keys to access special

features.

Í Places or answers a call.

´ Ends a call or exits special functions.

∏ Turns the phone on or off.

≥ and ≤ Adjust earpiece and ringer volume.

6 Numeric Keypad — Enters call information or programs features.

7 Headset Jack — For handsfree use with optional headset

accessory.

8 Mouthpiece

11

GETTING STARTED

Preparing Battery for Initial Use

The Nickel-Cadmium or Nickel Metal Hydride Battery supplied with

your telephone must be fully charged before placing your phone into

service. The batteries are shipped from the factory in a discharged

state in order to extend the life of the battery. It is recommended that

you charge new batteries overnight, but not longer than 24 hours,

using a Motorola-approved charger.

WARNING: Battery may explode if exposed to ﬁre. Charging your

battery in anything other than a Motorola charger will void

your warranty.

CAUTION: To prevent injuries or burns, do not allow metal objects

to contact or short circuit the battery terminals.

12

GETTING STARTED

Attaching the Battery

1. Place the battery pack on the phone so that its grooves align.

Align the top of the battery with the line on the back of the

phone right below the arrows.

2. Slide upward in the direction of the arrows on the back of the

phone until it clicks into place.

Battery Attachment

Removing the Battery

1. Turn your telephone off.

2. Depress the latch button on the rear of the battery and slide

the battery pack downward until it stops.

3. Lift the battery off.

Battery Removal

13

GETTING STARTED

Quick Change Method

The Quick Change Method allows you to remove your telephone

battery at any time and replace it with a charged spare battery dur-

ing a telephone call.

This is especially useful if you receive the Lo BAT(low battery)

message or audible tone during a call. Simply remove the battery

from the telephone, put on the spare battery, and press ∏. This

will return you to your telephone call. The phone will not go

through the normal power-up cycle described on page 15. You will

only have 4 seconds to complete this action before your telephone

call is terminated. It is a good idea to practice this procedure a few

times before using it on an actual phone call. Advise the party on

the other end of the call before beginning this procedure.

14

BASIC OPERATION

Turn Phone On

1. Extend antenna for optimal performance.

2. Press ∏ once.

3. Check the status indicators and display messages before plac-

ing a call.

Start-up Self Tests

Each time the telephone is turned on, it performs a series of self

tests, sounds a tone, and lights all display positions and status indi-

cators to check their operation. The signal strength meter and bat-

tery strength meter then display and the keypad lights momentarily,

as it will any time a key is pressed.

Message Explanation

•If your phone is programmed for two cel-

lular systems, one of these messages will

appear in the display upon power up.

•These are reminders as to which system

and phone number are currently

in use.

•Indicates that the phone has been locked

and cannot send or receive calls until

unlocked.

Loc/D

In Use Indicator

No Service Indicator Roam Indicator

888

8888888

15

BASIC OPERATION

A2

A1

B2

B1

BASIC OPERATION

Status Indicators Explanation

Indicators IU (In Use Indicator)

•Flashes when call is in progress.

NS (No Service Indicator)

•Flashes or lights steadily if phone

is beyond range of a cellular

service area.

•Calls cannot be placed or

received while NS is lit.

RM (Roam Indicator)

•If slow or rapid ﬂashing, you are

accessing a service area outside

of your home system.

Slow Flashing

Roaming on a home

type system.

Rapid Flashing

Roaming on a non-home

type system.

If no key is pressed within 8 seconds:

•The keypad backlight will extinguish to conserve the battery level.

•The signal strength meter will continue to ﬂash indicating that the

power is still on.

16

888

8888888

888

8888888

888

8888888

BASIC OPERATION

Placing a Call

1. With the power on, enter the number you wish to call.

2. Press Í.

3. Begin the conversation when the called party answers.

4. To terminate the call, press ´.

To Correct an Error

To clear the last digit entered, press and quickly release Ç. To

clear the entire entry, press and hold Ç until the entire entry

is erased.

If Entering More Than 10 Digits

You can call a phone number with up to 16 digits, but only the

last 10 digits will appear in the display.

When recalling a stored phone number that is longer than 10 dig-

its, the display will ﬂash the memory location number and the last

10 digits of the number. Press ‰ again to view entire number.

Unsuccessful Call Attempts

If you hear one of the following signals, you have not successfully

completed your call.

Tone / Message Description

Cellular System Busy

fast busy Press Í again before ending the unsuccessful

(reorder signal) call attempt to automatically redial the call

SND TO (refer to Automatic Redialing page 18), or press

REDIAL ´ and dial the call again.

Cellular System Could Not Complete the Call

alternating You may have tried to place a call before the

high/low tone NS

(No Service)

indicator stops ﬂashing to let

(intercept) you know your phone was fully operative.

SND TO Either press Í again before ending the

REDIAL unsuccessful call attempt to automatically redial

the call (refer to Automatic Redialing page 18),

or press ´ and dial the call again.

busy signal The called party’s line is busy.

17

BASIC OPERATION

Automatic Redialing

Your telephone includes a convenient feature designed to make

repetitive call attempts automatically when a cellular system

is busy.

If you receive an alternating high/low signal (intercept) or the fast

busy tone (reorder signal) when attempting to place a call and wish

to retry the call, press Í before ending the unsuccessful call

attempt. REDIAL is then displayed.

Your telephone will make the call attempt continuously over the

next 4 minutes. Once a connection is made, the phone will ring

once to alert you so that you may lift the phone to your ear and

begin the conversation.

If the call cannot be completed within 4 minutes, press Í to

begin another cycle.

Receiving a Call

1. Press Í.

NOTE: Pressing Í may activate call transfer or other optional

system features. Contact your Cellular System Provider for more

information.

Call in Absence Indicator

If your phone is on and an incoming call is unanswered, CALL is

displayed for 8 seconds. The display and keypad backlight will

extinguish to conserve the battery level. Pressing any key but Ç

or ´ redisplays CALL to inform you of the call attempt. You must

press Ç or ´ to cancel the message and clear the display.

NOTE: Phone will not display or retrieve the phone number of the

calling party.

Signal Strength Meter

The Signal Strength Meter (SSM) represents the relative strength of

the signal received by your phone. The SSM is displayed as shown.

The alone represents the lowest strength with each additional

representing a stronger signal.

18

BASIC OPERATION

Weak Signal Strong Signal

The SSM appears every time you turn your phone on. After 8

seconds, the SSM will continuously ﬂash the relative strength of the

signal received by the phone.

To best utilize the SSM, you should familiarize yourself with the rel-

ative Signal Strength levels and their associated Call Placement and

Call-in-Progress qualities.

Displaying Battery Voltage Meter

1. Press Ï, ›.

The Battery Voltage Meter (BVM) represents the current voltage

level of the battery being used. You can use this to estimate the

amount of battery capacity remaining. The BVM is displayed as a

battery bar graph at the left side of the display.

Low Battery Charged Battery

Variables such as temperature, battery age, and charging conditions

may affect battery voltage. To help remember which key to use,

note that “batt” appears on the › key.

Low Battery Warning

Low battery power is indicated by a short dual tone repeated peri-

odically, and the displayed message LoBAT. If the message is

ignored, the phone will automatically turn itself off as the battery

approaches discharge.



888

8888888

888

8888888

19

BASIC OPERATION

Adjusting Earpiece Volume

Press and hold ≥ or ≤ to raise or lower the earpiece volume

level.

Adjusting Ringer Volume

1. Press Ï.

2. Press and hold ≥ or ≤ to raise or lower ringer volume level.

V olume Meter

The Volume Meter represents the current volume setting and will

appear in the display whenever you adjust the earpiece or the

ringer volume.

Lowest Volume Highest Volume

The volume level is displayed as a bar graph following the letter v

at the left side of the display. The v alone represents the lowest vol-

ume setting with each additional bar representing a higher

volume setting.

Muting Microphone

1. While in a call, press Ï, ﬂ.

This feature allows you to confer privately with others during a con-

versation. If you press Ï, ﬂ during a call, the phone will dis-

play MUTE. To reinstate the microphone, press Ï, ﬂ again.

The mute feature is canceled when you end your call. To help you

remember which key to use, note that “mute” appears

on the ﬂ key.

Displaying Own Phone Number

1. Press ‰, £.

2. The phone number that is currently active will be displayed.

3. When you have ﬁnished viewing, press Ç.

v=v

20

Page is loading ...

Motorola PROFILE 300 Owner's manual

This manual is also suitable for

Motorola PROFILE 300 Owner's manual

Related papers

Other documents