PRECISION GRILL INSERTS
INSTALLATION INSTRUCTIONS
Ford, Expedition Platinum/Limited/Limited Max, Grill Insert (2015)
Combo Kit, Summer #374095
Consisting of Part # 372037 (Grill Insert) & #372049 (Bumper Insert)
*********************************************************************************
*********************************************************************************
- Before you install your Precision Grill Insert, see the diagrams and parts list for necessary parts.
- Your Grill Insert has been cleaned and the edge trimming applied. It is ready to install as Diagram indicates.
- Thread the thumbscrews onto the clip, just far enough to allow the locknut to fit fully onto the thumbscrew. Back
the clip up against the locknut. This will allow you to manipulate the clip easier. Position your grill insert using
the thumbscrew/clip assembly through the truck grill bar.
- Pull the screw assembly out until clip engages the truck grill bar. See Diagram #2. Maintain a slight pull on the
thumbscrew and turn clockwise. Finger tighten until snug.
*********************************************************************************
Ford Winter Grill Insert available from your dealer – Part No. 372038
PRECISION DESIGN & MANUFACTURING INC.
"C" CLIP
GRILL INSERT
SCREW
#8 X 1-3/4"
LOCK NUT
LOCK NUT
#8-32UNC
"C" CLIP
TOP GRILL
THUMB
SCREW
#8-32UNC
MIDDLE
PS
GRILL
BOTTOM GRILL
MIDDLE
DS
GRILL
Diagram #1
#372039 PARTS BAG CONTENTS
(12) Clip, “C”, 2’’ Part #371098
(12) Locknut, #8-32 Part #016002
(12) Thumb Screw, #8-32 Part #016009
Stainless Steel Parts
(1) Top Grill, SS Part #372041
(1) Mid DS Grill, SS Part #372042
(1) Mid PS Grill, SS Part #372043
(1) Bottom Grill, SS Part #372044
Diagram #2
PRECISION BUMPERSCREENS
INSTALLATION INSTRUCTIONS
Ford, Expedition Platinum/Limited/Limited Max, Grill Insert (2015)
Combo Kit, Summer #374095
Consisting of Part # 372037 (Grill Insert) & #372049 (Bumper Insert)
*********************************************************************************
*********************************************************************************
- Before you install your Precision Grill Insert, see the diagrams and parts list for necessary parts.
- Your Grill Insert has been cleaned and the edge trimming applied. It is ready to install as Diagram indicates.
- Thread the thumbscrews onto the clip, just far enough to allow the locknut to fit fully onto the thumbscrew. Back
the clip up against the locknut. This will allow you to manipulate the clip easier. Position your grill insert using
the thumbscrew/clip assembly through the truck grill bar.
- Pull the screw assembly out until clip engages the truck grill bar. See Diagram #2. Maintain a slight pull on the
thumbscrew and turn clockwise. Finger tighten until snug.
*********************************************************************************
PRECISION DESIGN & MANUFACTURING INC.
TOP BUMPER
INSERT
SCREW
#8 X 1
3
4
"
BOTTOM
BUMPER
INSERT
LOCK
NUT
TYPICAL SIDE CROSS SECTION
SHORT
''L'' CLIP
LONG
''L'' CLIP
TOP
BUMPER INSERT
LOCK NUT
#8-32UNC
SHORT "L" CLIP
THUMB
SCREW
#8-32UNC
BOTTOM
BUMPER INSERT
THUMB
SCREW
#8-32UNC
LOCK NUT
#8-32UNC
LONG "L" CLIP
PLUG HOLE
Diagram #1
#372050 PARTS BAG CONTENTS
(4) Clip, “L”, 0.594’’ Part #371765
(2) Clip, “L”, 0.875’’ Part #370354
(6) Locknut, #8-32 Part #016002
(6) Thumb Screw, #8-32 Part #016009
Stainless Steel Parts
(1) Top Bumper, SS Part #372051
(1) Bottom Bumper, SS Part #372052
Diagram #2
/
