PRECISION GRILL INSERTS
INSTALLATION INSTRUCTIONS
Ford F150, King Ranch/Lariat, Grill Insert (2015)
Combo Kit, Summer #374069
Consisting of Part # 371930 (Grill Insert) & #371929 (Bumper Insert)
*********************************************************************************
*********************************************************************************
- Before you install your Precision Grill Insert, see the diagrams and parts list for necessary parts.
- Your Grill Insert has been cleaned and the edge trimming applied. It is ready to install as Diagram indicates.
- Thread the thumbscrews onto the clip, just far enough to allow the locknut to fit fully onto the thumbscrew. Back
the clip up against the locknut. This will allow you to manipulate the clip easier. Position your grill insert using
the thumbscrew/clip assembly through the truck grill bar.
- Pull the screw assembly out until clip engages the truck grill bar. See Diagram #2. Maintain a slight pull on the
thumbscrew and turn clockwise. Finger tighten until snug.
- Precision Grill Inserts are designed to fit your truck. If they do not fit perfectly, they are installed incorrectly.
*********************************************************************************
Ford Winter Grill Insert available from your dealer – Part No. 371931
PRECISION DESIGN & MANUFACTURING INC.
Grill Insert, Kit # 371930
LOCK NUT
#8-32UNC
"C" CLIP
THUMB SCREW
#8-32UNC
TOP SCREEN
LEFT SCREEN
RIGHT SCREEN
BOTTOM SCREEN
Diagram #1
#371922 PARTS BAG CONTENTS
(12) Clip, “C”, 1.5’’ Part #370820
(12) Locknut, #8-32 Part #016002
(12) Thumb Screw, #8-32 Part #016009
Stainless Steel Parts
(1) Top Screen, Part #371919
(1) Middle PS Screen, Part #371920
(1) Middle DS Screen Part #371921
(1) Bottom Screen Part #371927
GRILL INSERT
LOCK NUT
SCREW
#8 X 1-3/4"
"C" CLIP
TYPICAL SIDE CROSS SECTION
Diagram #2
(Note: the slotting pattern on the actual products may vary from installation diagrams.)
PRECISION BUMPERSCREENS
INSTALLATION INSTRUCTIONS
Ford F150, King Ranch/Lariat, Grill Insert (2015)
Combo Kit, Summer #374069
Consisting of Part # 371930 (Grill Insert) & #371929 (Bumper Insert)
*********************************************************************************
*********************************************************************************
- Before you install your Precision Bumper Insert, see the diagrams and parts list for necessary parts.
- Your Bumper Insert has been cleaned and the edge trimming applied. It is ready to install as Diagram indicates.
- Take out the license plate and its supporting bar to make the bumper area resemble the one in diagram #1.
- Thread the thumbscrews onto the clip, just far enough to allow the locknut to fit fully onto the thumbscrew. Back
the clip up against the locknut. This will allow you to manipulate the clip easier.
- Position your bumper insert to have the thumbscrew/clip assemblies behind the truck body (as shown in diagram
#2, but loosened for now), and insert two untrimmed edges into the truck bumper (as shown in diagram #3).
- Pull the screw assembly out until clip engages the truck bumper. See Diagram #2. Maintain a slight pull on the
thumbscrew and turn clockwise. Finger tighten until snug.
- Install the license plate and its supporting bar back onto the truck body.
Precision Bumper Inserts are designed to fit your truck. If they do not fit perfectly, they are installed incorrectly.
*********************************************************************************
PRECISION DESIGN & MANUFACTURING INC.
GRILL INSERT
LOCK NUT
THUMB SCREW
#8-32UNC
"C" CLIP
TYPICAL SIDE CROSS SECTION
LOCK NUT
THUMB SCREW
#8-32UNC
"C" CLIP
LOCK NUT
#8-32UNC
FORD BODY
BUMPER INSERT
BUMPER INSERT
Bumper Insert, Kit # 371929
Diagram #1
Diagram #2
(Note: the slotting pattern on the actual products may vary from installation diagrams.)
#371941 PARTS BAG CONTENTS
(4) Clip, “C”, 2’’ Part #371098
(4) Locknut, #8-32 Part #016002
(4) Thumb Screw, #8-32 Part #016009
Stainless Steel Parts
(1) Bumper Insert, SS Part #371923
INSTALLED
VIEW
Diagram #3
/