Omnitron 2423-1-T Datasheet

Brand: Omnitron

Model: 2423-1-T

Category: Network media converters

Type: Datasheet

This manual is also suitable for

2422-0-T

iConverteriConverter

■ Modular system multiplexes up to sixteeen independent

T1/E1 circuits and 10/100/1000 Ethernet over ber or

Ethernet Virtual Connection (EVC)

■ Multiple groups of mux modules can be installed in the

same chassis

■ Remotely-managed conguration and testing enables

rapid deployment

■ Manageable via SNMP with Omnitron’s NetOutlook

Management Software or third party software

■ CLI management interface via TELNET or serial port

■ Optional connectivity to adjacent Ethernet switch modules

■ Commercial (0 to 50º C ) and wide (-40 to 60º C)

operating temperature ranges

iConverter Fiber Transport Modules

■ Fiber Transport modules are available for point-to-point

Ethernet or Carrier Ethernet Virtual Connection (EVC)

■ Small Form Pluggable (SFP) or xed ber transceivers, in

standard and CWDM wavelengths

■ Multimode, single-mode dual ber and single-mode

single-ber options.

iConverter 4xT1/E1 MUX Modules

■ In-band T1 loop-back

■ Out-of-band local loop-back on the copper and ber ports,

remote ber loop-back and circuit test modes

■ Supports balanced T1/E1 or unbalanced E1

■ Congurable alarm relay contacts for audio/visual fault

notication

■ 24 hour T1/E1 statistic logging

■ Optional external I/O clock port

iConverter

Modular T1/E1 Multiplexer

T1/E1 and Ethernet Managed Multiplexer System

The iConverter Modular T1/E1 Multiplexer transports up to

sixteen T1/E1 circuits and 10/100/1000 Ethernet over point-

to-point ber, CWDM channel or Ethernet Virtual Connection

(EVC). This exible and scalable system is comprised of an

iConverter Fiber Transport module, and one or more iConverter

4xT1/E1 MUX modules installed in a 2, 5 or 19-module chassis.

Each iConverter Fiber Transport module and up to four

contiguous iConverter 4xT1/E1 MUX modules combine to form

a MUX group. A MUX group can connect with another MUX

group at the opposite end of a dedicated ber link or EVC.

A MUX group can also interoperate with a Managed iConverter

xed-conguration T1/E1 Multiplexer.

Multiple MUX groups can be installed in a chassis, enabling

high-density, star-topology deployments.

There are three Fiber Transport modules available: the

iConverter TM3, the iConverter GM3 NID plug-in module and

the iConverter GM4 NID plug-in module. The TM3 supports

Ethernet Link OAM with IEEE 802.3ah. The GM3 and GM4

NID modules support Carrier Ethernet Service OAM with IEEE

802.1ag Connectivity Fault Management and ITU-T Y.1731

Performance Monitoring. See the ber transport module

comparison table on page 2 for more information.

The Fiber Transport module is available with xed-ber or Small

Form Pluggable (SFP) transceivers, and feature two Ethernet

backplane ports for additional Ethernet connectivity to adjacent

modules. A common application of this feature is to combine a

4-Port switch module in the adjacent slot to provide a solution

with four additional 10/100/1000 ports.

The iConverter 4xT1/E1 MUX module supports four copper

RJ-48 ports for balanced T1/E1 applications. Adapter cables

are available to convert each RJ-48 interface to a BNC interface

for unbalanced E1 transport applications.

The 4xT1/E1 MUX module features an optional external clock

port that can be congured as a clock input or output. As an

input, the port can be connected to an external clock source,

such as a GPS receiver, to provide a common reference

clock for the module. As an output, the port can provide the

recovered T1/E1 clock from port 1 to other TDM equipment

at the site.

The T1/E1 Multiplexer modules are part of the iConverter multi-

service platform, and can be installed in a chassis equipped

with iConverter Network Interface Devices, media converters,

transponders and CWDM multiplexers. The multi-service

platform is capable of delivering Ethernet, TDM, SONET

and other services across a Wide Area Network. iConverter

modules can be added to this scalable architecture to expand

bandwidth capacity and add new services.

KEY FEATURES

The T1/E1 Multiplexer system features integrated management.

Monitoring, conguration and remote testing functions can be

accessed through the iConverter Fiber Transport module serial

console port, IP-based SNMP or IP-less OAM channels. Alarm

relays and SNMP traps provide fault notication for loss of

power, LOS and AIS.

SNMP management via NetOutlook provides a graphical user

interface for real-time port and module information, local and

remote conguration, and trap notication.

Page 2

iConverter Modular T1/E1 Multiplexer

SPECIFICATIONS

Model Type

iConverter TM3 Fiber Transport Modules

Protocols

10BASE-T, 100BASE-TX, 1000BASE-T,

100BASE-FX, 1000BASE-X Ethernet

Compliance UL, CE, FCC Class A, NEBS 3 Compliant

IP-Based Management TELNET, SNMPv1, SNMPv2c, SNMPv3

Frame Size Up to 10,240 byte frames

Copper Connectors Ethernet: RJ-45

Fiber Connectors

SFP Model:

Dual Fiber Model:

Single-Fiber Model:

Any MSA standard SFP

SC, ST

Serial Connector

Mini DIN-6 female

Mini DIN-6 male to DB-9 female adapter

included

Dimensions W: 0.85” x D: 4.5” X H: 2.8”

Weight 8oz.

Humidity 5 to 95% (non-condensing)

Altitude -100m to 4000m

Power

Typical input power requirements:

1.6A @ 3.3VDC

Connector: Power supplied by backplane

Temperature

Standard Operating:

Wide Operating:

Storage:

0 to 50º C

-40 to 60º C

-40 to 80º C

MTBF (hrs) 340,000 hrs

Model Type

iConverter 4xT1/E1 MUX Module

Protocols

ANSI: T1.403, T1.102

AT&T: T62411, ITU: G.703, G.704, G.706,

G.736, G.775, G.823, G.824, G.8261

ETSI: ETS 300 166

Compliance UL, CE, FCC Class A, NEBS 3 Compliant

Connectors T1/E1: RJ-48, Optional BNC, SMB (8484-4)

Clock I/O Port

(8486-4 only)

Input:

Output:

10 MHz, 1.544 MHz, or 2.048 MHz

Recovered clock from Port 1 SMB

Dimensions W: 0.85” x D: 4.5” X H: 2.8”

Weight 8oz.

Humidity 5 to 95% (non-condensing)

Altitude -100m to 4000m

Power

Typical input power requirements:

1.6A @ 3.3VDC

Connector: Power supplied by backplane

Temperature

Standard Operating:

Wide Operating:

Storage:

0 to 50º C

-40 to 60º C

-40 to 80º C

MTBF (hrs)

410,000 hrs

MANAGEMENT

iConverter Fiber Transport Modules

Feature TM3 GM3 GM4

TELNET, SNMP v1, v2c, v3

4 4 4

SSH Secure Management

Zero-Touch Provisioning

4 4

ITU-T Y.1564 Service Testing

RFC 2544 Throughput Testing

IEEE 802.3ah

4 4 4

IEEE 802.1ag

4 4

ITU-T Y.1731

4 4

Tag VLAN (Q-in-Q)

4 4

Service Multiplexing (EVPL)

4 4

Rapid Spanning Tree Protocol

4 4

G.8031 Linear Protection

G.8032 Ring Protection

Y.1588 Clocking

Rate Limiting

4 4

MIB Statistics (RMON)

4 4 4

Fault Propagation Link Modes

4 4 4

L2CP Policy Manager

4 4

L2PT

4 4

FIBER TRANSPORT MODULES

For GM3 or GM4 specications, see the respective data sheets.

Page 3

iConverter Modular T1/E1 Multiplexer

APPLICATIONS

The iConverter Modular T1/E1 Multiplexer system is designed

for service provider, enterprise, government and energy/utility

networks.

Enterprise and government applications include extension of

multiple T1/E1 circuits from a service provider demarcation

point, and building-to-building PBX connectivity.

Service provider and utility applications include mobile

backhaul and business services that require delivery of multiple

T1/E1s and/or Ethernet.

Mobile Backhaul

In this application diagram, iConverter Modular T1/E1

Multiplexers deliver Ethernet and T1 mobile backhaul.

At the Mobile Switching Center, two iConverter MUX groups

are installed in a high-density 19-module chassis, and connect

to TDM and IP networks. The iConverter MUX groups convert

RJ-45 Ethernet and T1 interfaces to ber, and transport the

multiplexed data over the ber links.

At the Cell Sites, MUX groups are installed in 2-module or

5-module chassis. The ber link with multiplexed data is

converted back to RJ-45 Ethernet and T1 interfaces where

they connect to the tower’s radio equipment.

Using the GM3 or GM4 Transport modules enables a seamless

migration from 2G (T1s), to 3G (T1s and Ethernet), to 4G/LTE

(Carrier Ethernet).

Ethernet and TDM Business Services

In this application diagram, iConverter Modular T1/E1

Multiplexers deliver Ethernet and T1s over an Ethernet Virtual

Connection (EVC). A two module chassis with a GM4 Fiber

Transport Module and a T1/E1 MUX module are installed at

each customer location.

The EVC transports the business Ethernet and four T1 circuits

between the two customer locations across a Carrier Ethernet

network. The Ethernet transports business data, and the T1s

are used for telephony services (PBX to PBX connectivity).

ORDERING INFORMATION

Page 4

800-675-8410 • 949-250-6510 • www.omnitron-systems.com • [email protected] • 140 Technology Dr., Irvine, CA 92618

iConverter Modular T1/E1 Multiplexer

Trademarks are owned by their respective companies. Specications are subject to change without notice.

091-12420-001D 1/13

iConverter TM3 Transport Module

Port Conguration Fiber Type Distance Wavelength P1 Connector Type

Lambda

(nm)

Lambda

(nm)

Min. Tx

Power

(dBm)

Max. Tx

Power

(dBm)

Min. Rx

Sensitivity

(dBm)

Max. Rx

Power

(dBm)

Min Att.

Link

Budget

(dB)

P1 P2 (nm) ST SC SFP

FF UTP MM-DF 220/550m 850 2420-0-T 2422-0-T - 850 850 -10 -4 -17 -3 - 7

FF UTP SM-DF 12km 1310 2421-1-T 2423-1-T - 1310 1310 -9.5 -3 -19.5 -3 - 10

FF UTP SM-DF 34km 1310 2421-2-T 2423-2-T - 1310 1310 -5 0 -23 -3 3 18

FF UTP SM-DF 80km 1550 - 2423-3-T - 1550 1550 -5 0 -23 -3 3 18

FF UTP SM-DF 110km 1550 - 2423-4-T - 1550 1550 0 5 -24 -3 8 24

FF UTP SM-DF 140km 1550 - 2423-5-T - 1550 1550 2 5 -28 -8 13 30

FF UTP SM-SF 20km 1310/1550 - 2430-1-T* - 1310 1550 -9.5 -3 -20 -3 - 10.5

FF UTP SM-SF 20km 1550/1310 - 2431-1-T* - 1550 1310 -9.5 -3 -20 -3 - 10.5

FF UTP SM-SF 40km 1310/1550 - 2430-2-T* - 1310 1550 -3 0 -20 -3 3 17

FF UTP SM-SF 40km 1550/1310 - 2431-2-T* - 1550 1310 -3 0 -20 -3 3 17

SFP UTP - - - - - 2439-0-T** Order the appropriate SFPs separately. Visit the Optical Transceivers web page.

SFP SFP - - - - - 2499-0-T** Order the appropriate SFPs separately. Visit the Optical Transceivers web page.

FF - Fixed Fiber, UTP - Unshielded Twisted Pair, SFP - Small Form Pluggable Transceiver

*When using single-ber (SF) media converter models, the Tx wavelength on one end has to match the Rx wavelength on the other.

**Order ber or copper SFPs separately

To order a wide temperature (-40 to 60°C) TM3 module, add a “W” to the end of the model number.

See the GM4 or GM3 NID data sheets for ordering information.

Visit the GM4 NID web page

Visit the GM3 NID web page

iConverter 4xT1/E1 MUX Module

4 T1/E1 4 T1/E1 with Clock I/O

Model Number 8485-4 8486-4

To order a wide temperature (-40 to 60°C) 4xT1/E1 MUX module, add a “W” to the end of the model number.

Accessories

9140-3 RJ-48 to dual BNC plug cable, 3m

9142-1 RJ-48 Alarm Breakout Cable

9144-6 50 OHM mini-coax plug to BNC plug adapter cable, 6”

Omnitron 2423-1-T Datasheet

Brand: Omnitron

Model: 2423-1-T

Category: Network media converters

Type: Datasheet

This manual is also suitable for

2422-0-T

Download PDF

report

Omnitron 2423-1-T Datasheet

This manual is also suitable for

Omnitron 2423-1-T Datasheet

Related papers

Other documents