Nilfisk-ALTO SCRUBTEC 343E User manual

Page is loading ...

EC Machinery Directive 98/37/EC EN ISO 12100-1, EN ISO 12100-2, EN 294, EN 349

EC Low Voltage Directive 73/23/EEC EN 60335-1, EN 60335-2-72

EC EMC Directive 89/336/EEC EN 61000, EN 50366

FAC-SIMILE

FA

EC Machinery DirectivEC Machinery Dir

EC Low Voltage DireLow Voltage Dire

EC EMC Directive 8C EMC Directive 8

Manufacturer: Alto Deutschland GmbH

Authorized signatory: Dipl.-Ing. Wolfgang Nieuwkamp

Date: 02.01.2007 Signature:

Address: Guido-Oberdorfer-Straße 2-8 — D-89287 Bellenberg

Ⱦɨɥɭɩɨɞɩɢɫɚɧɢɹɬ ɩɨɬɜɴɪɠɞɚɜɚ, ɱɟ

ɝɨɪɟɫɩɨɦɟɧɚɬɢɹɬ ɦɨɞɟɥ ɟ ɩɪɨɢɡɜɟɞɟɧ ɜ

ɫɴɨɬɜɟɬɫɬɜɢɟ ɫɴɫ ɫɥɟɞɧɢɬɟ ɞɢɪɟɤɬɢɜɢ ɢ

ɫɬɚɧɞɚɪɬɢ.

Níže podepsaný stvrzuje, že výše

uvedený model byl vyroben v souladu s

následujícími smČrnicemi a normami.

Der Unterzeichner bestätigt hiermit dass

die oben erwähnten Modelle gemäß

den folgenden Richtlinien und Normen

hergestellt wurden.

Undertegnede attesterer herved, at

ovennævnte model er produceret i

overensstemmelse med følgende direktiver

og standarder.

El abajo ¿ rmante certi¿ ca que los modelos

arriba mencionados han sido producidos

de acuerdo con las siguientes directivas y

estandares.

Allakirjutanu kinnitab, et ülalnimetatud

mudel on valmistatud kooskõlas järgmiste

direktiivide ja normidega.

Je soussigné certi¿ e que les modèles ci-

dessus sont fabriqués conformément aux

directives et normes suivantes.

Allekirjoittaia vakuuttaa että yllämainittu

malli on tuotettu seuraavien direktiivien ja

standardien mukaan.

The undersigned certify that the above

mentioned model is produced in

accordance with the following directives

and standards.

ȅ țȐĲȦșȚ ȣʌȠȖİȖȡĮȝȝȑȞȠȢ ʌȚıĲȠʌȠȚİȓ ȩĲȚ Ș

ʌĮȡĮȖȦȖȒ ĲȠȣ ʌȡȠĮȞĮĳİȡșȑȞĲȠȢ ȝȠȞĲȑȜȠȣ

ȖȓȞİĲĮȚ ıȪȝĳȦȞĮ ȝİ ĲȚȢ ĮțȩȜȠȣșİȢ ȠįȘȖȓİȢ

țĮȚ ʌȡȩĲȣʌĮ.

Alulírottak igazoljuk, hogy a fent említett

modellt a következĘ irányelvek és

szabványok alapján hoztuk létre.

Il sottoscritto dichiara che i modelli sopra

menzionati sono prodotti in accordo con le

seguenti direttive e standard.

Toliau pateiktu dokumentu patvirtinama,

kad minơtas modelis yra pagamintas

laikantis nurodytǐ direktyvǐ bei standartǐ.

Ar šo tiek apliecinƗts, ka augstƗkminƝtais

modelis ir izgatavots atbilstoši šƗdƗm

direktƯvƗm un standartiem.

Undertegnede attesterer att ovennevnte

modell är produsert i overensstemmelse

med fölgende direktiv og standarder.

Ondergetekende verzekert dat de

bovengenoemde modellen geproduceerd

zijn in overeenstemming met de volgende

richtlijnen en standaards.

A presente assinatura serve para declarar

que os modelos supramencionados

são produtos em conformidade com as

seguintes directivas e normas.

NiĪej podpisany zaĞwiadcza, Īe

wymieniony powyĪej model produkowany

jest zgodnie z nastĊpującymi dyrektywami

i normami.

Subsemnatul atest că modelul sus-

menĠionat este produs în conformitate cu

următoarele directive úi standarde.

ɇɚɫɬɨɹɳɢɦ ɭɞɨɫɬɨɜɟɪɹɟɬɫɹ, ɱɬɨ ɦɚɲɢɧɚ

ɜɵɲɟɭɤɚɡɚɧɧɨɣ ɦɨɞɟɥɢ ɢɡɝɨɬɨɜɥɟɧɚ

ɜ ɫɨɨɬɜɟɬɫɬɜɢɢ ɫɨ ɫɥɟɞɭɸɳɢɦɢ

ɞɢɪɟɤɬɢɜɚɦɢ ɢ ɫɬɚɧɞɚɪɬɚɦɢ.

Undertecknad intygar att ovannämnda

modell är producerad i överensstämmelse

med följande direktiv och standarder.

Dolu podpísaný osvedþuje, že hore

uvedený model sa vyrába v súlade s

nasledujúcimi smernicami a normami.

Spodaj podpisani potrjujem, da je zgoraj

omenjeni model izdelan v skladu z

naslednjimi smernicami in standardi.

Aúa÷ıda ømzası olan kiúi, yukarıda

bahsedilen model cihazın aúa÷ıda verilen

direktiÀ ere ve standartlara uygunlukta imal

edildi÷ini onaylar.

Ɇɨɞɟɥ / Model / Modell / Model / Modelo / Mudel / Modèle / Malli /

Model / ȂȠȞĲȑȜȠ / Modell / Modello / Modelis / Modelis / Modell / Model

/ Modelo / Model / Model / Ɇɨɞɟɥɶ / Modell / Model / Model / Model :

Ɍɢɩ / Typ / Typ / Type / Tipo / Tüüp / Type / Tyyppi / Type / ȉȪʌȠȢ /

Típus / Tipo / Tipas / Tips / Type / Type / Tipo / Typ / Tip / Ɍɢɩ / Typ /

Typ / Tip / Tip :

ɋɟɪɢɟɧ ɧɨɦɟɪ / Výrobní þíslo / Seriennummer / Serienummer / Número de serie / Seerianumber / Numéro de série / Sarjanumero / Serial number

/ ȈİȚȡȚĮțȩȢ ĮȡȚșȝȩȢ / Sorozatszám / Numero di serie / Serijos numeris / SƝrijas numurs / Serienummer / Serienummer / Número de série / Numer

seryjny / Număr de serie / ɋɟɪɢɣɧɵɣ ɧɨɦɟɪ / Serienummer / Výrobné þíslo / Serijska številka / Seri Numarası :

Ƚɨɞɢɧɚ ɧɚ ɩɪɨɢɡɜɨɞɫɬɜɨ / Rok výroby / Baujahr / Fabrikationsår / Año de fabricación / Väljalaskeaasta / Année de fabrication / Valmistusvuosi / Year

of construction / ǲĲȠȢ țĮĲĮıțİȣȒȢ / Gyártási év / Anno di costruzione / Pagaminimo metai / Izgatavošanas gads / Byggeår / Bauwjaar / Ano de fabrico

/ Rok produkcji / Anul fabricaĠiei / Ƚɨɞ ɜɵɩɭɫɤɚ / Tillverkningsår / Rok výroby / Leto izdelave / Leto izdelave/ømal yılı :

ɋɟɪɬɢɮɢɤɚɬ ɡɚ ɫɴɨɬɜɟɬɫɬɜɢɟ

OsvČdþení o shodČ

Konformitätserklärung

Overensstemmelsescerti¿ kat

Declaración de conformidad

Vastavusserti¿ kaat

Déclaration de conformité

Yhdenmukaisuustodistus

Conformity certi¿ cate

ȆȚıĲȠʌȠȚȘĲȚțȩ ıȣȝȝȩȡĳȦıȘȢ

MegfelelĘsségi nyilatkozat

Dichiarazione di conformità

Atitikties deklaracija

AtbilstƯbas deklarƗcija

Konformitetsserti¿ sering

Conformiteitsverklaring

Declaração de conformidade

Deklaracja zgodnoĞci

Certi¿ cat de conformitate

Ɂɚɹɜɥɟɧɢɟ ɨ ɫɨɨɬɜɟɬɫɬɜɢɢ

Överensstämmelsecerti¿ kat

Certi¿ kát súladu

Certi¿ kat o ustreznosti

Uyumluluk serti¿ kası

SCRUBBER-DRYER

SCRUBTEC 343E

Page is loading ...

909 6315 000(2)2007-06 A SCRUBTEC 343E 1

MANUEL OPERATEUR

FRANÇAIS

TABLE DES MATIERES

INTRODUCTION .............................................................................................................................................................. 2

BUT ET CONTENU DU MANUEL ................................................................................................................................................... 2

DESTINATAIRES ............................................................................................................................................................................. 2

CONSERVATION DU MANUEL ....................................................................................................................................................... 2

DECLARATION DE CONFORMITE ................................................................................................................................................ 2

DONNEES D'IDENTIFICATION ...................................................................................................................................................... 2

AUTRES MANUELS DE REFERENCE ........................................................................................................................................... 2

PIECES DE RECHANGE ET ENTRETIEN ..................................................................................................................................... 2

MODIFICATIONS ET AMELIORATIONS ......................................................................................................................................... 3

CAPACITES OPERATIONNELLES ................................................................................................................................................. 3

CONVENTIONS .............................................................................................................................................................................. 3

DEBALLAGE / LIVRAISON ............................................................................................................................................. 3

SECURITE ....................................................................................................................................................................... 3

SYMBOLES UTILISES .................................................................................................................................................................... 3

INSTRUCTIONS GENERALES ....................................................................................................................................................... 4

DESCRIPTION DE LA MACHINE ................................................................................................................................... 6

STRUCTURE DE LA MACHINE ...................................................................................................................................................... 6

TABLEAU DE BORD ....................................................................................................................................................................... 8

ACCESSOIRES / OPTIONS ............................................................................................................................................................ 8

CARACTERISTIQUES TECHNIQUES ............................................................................................................................................ 8

SCHEMA ELECTRIQUE .................................................................................................................................................................. 9

AVANT LA MISE EN MARCHE ...................................................................................................................................................... 10

MISE EN MARCHE ET ARRET DE LA MACHINE .........................................................................................................................11

MACHINE AU TRAVAIL (LAVAGE / SECHAGE) ............................................................................................................................11

TRANSPORT / STATIONNEMENT DE LA MACHINE ................................................................................................................... 12

APRES L'UTILISATION DE LA MACHINE .................................................................................................................................... 13

DEPOSE DU RESERVOIR DE L'EAU DE RECUPERATION ....................................................................................................... 13

INACTIVITE PROLONGEE DE LA MACHINE .............................................................................................................................. 13

PREMIERE PERIODE D'UTILISATION ......................................................................................................................................... 13

ENTRETIEN ................................................................................................................................................................... 14

PLAN D'ENTRETIEN PROGRAMME ............................................................................................................................................ 14

NETTOYAGE DE L'EMBOUCHURE ............................................................................................................................................. 15

CONTROLE ET REMPLACEMENT DES LAMELLES EN CAOUTCHOUC DE L'EMBOUCHURE .............................................. 15

NETTOYAGE DE LA BROSSE ...................................................................................................................................................... 16

NETTOYAGE DES RESERVOIRS ET DE LA GRILLE D'ASPIRATION ........................................................................................ 16

NETTOYAGE DU FILTRE DE LA SOLUTION ............................................................................................................................... 17

REGLAGE DE LA VITESSE D'AVANCE DE LA MACHINE ........................................................................................................... 17

DEPISTAGE DES PANNES ........................................................................................................................................... 18

MISE EN DECHARGE ................................................................................................................................................... 18

Page is loading ...

909 6315 000(2)2007-06 A SCRUBTEC 343E 1

USER MANUAL

ENGLISH

TABLE OF CONTENTS

INTRODUCTION .............................................................................................................................................................. 2

MANUAL PURPOSE AND CONTENTS .......................................................................................................................................... 2

TARGET ........................................................................................................................................................................................... 2

HOW TO KEEP THIS MANUAL ....................................................................................................................................................... 2

DECLARATION OF CONFORMITY ................................................................................................................................................ 2

IDENTIFICATION DATA ................................................................................................................................................................... 2

OTHER REFERENCE MANUALS ................................................................................................................................................... 2

SPARE PARTS AND MAINTENANCE ............................................................................................................................................. 2

CHANGES AND IMPROVEMENTS ................................................................................................................................................ 3

OPERATION CAPABILITIES ........................................................................................................................................................... 3

CONVENTIONS .............................................................................................................................................................................. 3

UNPACKING/DELIVERY ................................................................................................................................................. 3

SAFETY ........................................................................................................................................................................... 3

SYMBOLS ....................................................................................................................................................................................... 3

GENERAL INSTRUCTIONS ............................................................................................................................................................ 4

MACHINE DESCRIPTION ............................................................................................................................................... 6

MACHINE STRUCTURE ................................................................................................................................................................. 6

CONTROL PANEL ........................................................................................................................................................................... 8

ACCESSORIES/OPTIONS .............................................................................................................................................................. 8

TECHNICAL DATA ........................................................................................................................................................................... 8

WIRING DIAGRAM .......................................................................................................................................................................... 9

BEFORE MACHINE START-UP .................................................................................................................................................... 10

MACHINE START AND STOP ........................................................................................................................................................11

MACHINE OPERATION (SCRUBBING/DRYING) ..........................................................................................................................11

MACHINE TRANSPORT/PARKING .............................................................................................................................................. 12

AFTER USING THE MACHINE ..................................................................................................................................................... 13

RECOVERY WATER TANK REMOVAL ......................................................................................................................................... 13

MACHINE LONG INACTIVITY ...................................................................................................................................................... 13

FIRST PERIOD OF USE ............................................................................................................................................................... 13

MAINTENANCE ............................................................................................................................................................. 14

SCHEDULED MAINTENANCE TABLE ......................................................................................................................................... 14

SQUEEGEE CLEANING ............................................................................................................................................................... 15

SQUEEGEE BLADE CHECK AND REPLACEMENT .................................................................................................................... 15

BRUSH CLEANING ....................................................................................................................................................................... 16

TANK AND VACUUM GRID CLEANING ....................................................................................................................................... 16

SOLUTION FILTER CLEANING .................................................................................................................................................... 17

MACHINE SPEED ADJUSTMENT ................................................................................................................................................ 17

TROUBLESHOOTING ................................................................................................................................................... 18

SCRAPPING .................................................................................................................................................................. 18

2 SCRUBTEC 343E 909 6315 000(2)2007-06 A

ENGLISH USER MANUAL

INTRODUCTION

NOTE

The numbers in brackets refer to the components shown in Machine Description chapter.

MANUAL PURPOSE AND CONTENTS

The purpose of this Manual is to provide the operator with all necessary information to use the machine properly, in a safe and

autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal.

Before performing any procedure on the machine, the operators and qualiﬁ ed technicians must read this Manual carefully. Contact

Alto in case of doubts concerning the interpretation of the instructions and for any further information.

TARGET

This Manual is intended for operators and technicians qualiﬁ ed to perform the machine maintenance.

The operators must not perform procedures reserved for qualiﬁ ed technicians. Alto will not be answerable for damages coming from

the non-observance of this prohibition.

HOW TO KEEP THIS MANUAL

The User Manual must be kept near the machine, inside an adequate case, away from liquids and other substances that can cause

damage to it.

DECLARATION OF CONFORMITY

The Declaration of Conformity, supplied with the machine, certiﬁ es the machine conformity with the law in force.

NOTE

Two copies of the original declaration of conformity are provided together with the machine documentation.

IDENTIFICATION DATA

The machine model and serial number are marked on the plate (1).

The machine model year is written in the declaration of conformity and it is also indicated by the ﬁ rst two ﬁ gures of the machine

serial number.

This information is useful when requiring machine spare parts. Use the following table to write down the machine identiﬁ cation data.

MACHINE model ...............................................................................

MACHINE serial number ...................................................................

OTHER REFERENCE MANUALS

Spare Parts List (supplied with the machine)

Service Manual (that can be consulted at Alto Service Centers)

SPARE PARTS AND MAINTENANCE

All necessary operating, maintenance and repair procedures must be performed by qualiﬁ ed personnel or by Alto Service Centers.

Only original spare parts and accessories must be used.

Contact Alto for service or to order spare parts and accessories, specifying the machine model and serial number.

–

909 6315 000(2)2007-06 A SCRUBTEC 343E 3

USER MANUAL

ENGLISH

CHANGES AND IMPROVEMENTS

Alto constantly improves its products and reserves the right to make changes and improvements at its discretion without being

obliged to apply such beneﬁ ts to the machines that were previously sold.

Any change and/or addition of accessories must be approved and performed by Alto.

OPERATION CAPABILITIES

These scrubber-dryers are used to clean (scrubbing and drying) smooth and solid ﬂ oors, in civil or industrial environment, under

safe operation conditions by a qualiﬁ ed operator.

The scrubber-dryers cannot be used for ﬁ tted carpet and carpet cleaning.

CONVENTIONS

Forward, backward, front, rear, left or right are intended with reference to the operator’s position, that is to say in driving position

with the hands on the handlebar (2).

UNPACKING/DELIVERY

To unpack the machine, carefully follow the instructions on the packing.

When the machine is delivered, check that the packing and the machine were not damaged during transportation. In case of visible

damages, keep the packing and have it checked by the Carrier that delivered it. Call the Carrier immediately to ﬁ ll in a damage

claim.

Please check that the following items have been supplied with the machine:

Scrubber-dryer User Manual

Scrubber-dryer Spare Parts List

Supply cable extension

SAFETY

The following symbols indicate potentially dangerous situations. Always read this information carefully and take all necessary

precautions to safeguard people and property.

The operator's cooperation is essential in order to prevent injury. No accident prevention program is effective without the total

cooperation of the person responsible for the machine operation. Most of the accidents that may occur in a factory, while working

or moving around, are caused by failure to comply with the simplest rules for exercising prudence. A careful and prudent operator is

the best guarantee against accidents and is essential for successful completion of any prevention program.

SYMBOLS

DANGER!

It indicates a dangerous situation with risk of death for the operator.

WARNING!

It indicates a potential risk of injury for people or damage to objects.

CAUTION!

It indicates a caution related to important or useful functions.

Pay careful attention to the paragraphs marked by this symbol.

NOTE

It indicates the necessity to refer to the User Manual before performing any procedure.

–

4 SCRUBTEC 343E 909 6315 000(2)2007-06 A

ENGLISH USER MANUAL

GENERAL INSTRUCTIONS

Speciﬁ c warnings and cautions to inform about potential damages to people and machine are shown below.

DANGER!

Always disconnect the power supply cable when the machine is not in use, before performing maintenance

procedures, before replacing the brush/pad-holder and before opening any access panel.

This machine must be used by properly trained and authorised personnel only. Children or disabled people cannot

use this machine.

Do not wear jewels when working near electrical components.

Do not work under the lifted machine without supporting it with safety stands.

Do not operate the machine near toxic, dangerous, ﬂ ammable and/or explosive powders, liquids or vapours.

WARNING!

The machine power supply cable is grounded and the relevant plug is grounded too. In case of machine malfunction

or breakdown, grounding connection reduces the risk of electric shock.

The power supply cable plug must be connected to an appropriate outlet, which is grounded according to law in

force.

Improper connection can cause electric shock. Consult a qualiﬁ ed technician to make sure that the outlet is properly

grounded.

Do not tamper with the power supply cable plug. If the power supply cable plug cannot be connected to the outlet,

have new grounded outlet installed by a qualiﬁ ed technician, according to the law in force.

Before connecting the power supply cable to the electrical mains, check that frequency and voltage, shown on the

machine serial number plate (1), match the electrical mains voltage.

Do not unplug the machine by pulling the supply cable. To unplug, grasp the plug, not the cable.

Do not handle the plug or the machine with wet hands.

Turn off all controls before unplugging.

Regularly check the power supply cable for damages, cracks, cuts, etc. If the power supply cable is damaged, replace

it immediately.

To avoid any risk, if the power supply cable is damaged, contact Alto Service Center or a qualiﬁ ed technician.

Do not pull or carry the machine by the power supply cable and never use the power supply cable as a handle. Do not

close a door on the power supply cable, or pull the power supply cable around sharp edges or corners. Do not run

the machine on the power supply cable.

Keep the power supply cable away from heated surfaces.

To reduce the risk of ﬁ re, electric shock, or injury, do not leave the machine unattended when it is plugged in.

Disconnect the machine from the electrical mains when not in use and before performing maintenance procedures.

Always protect the machine against the sun, rain and bad weather, both under operation and inactivity condition.

Store the machine indoors, in a dry place.

Do not allow to be used as a toy. Close attention is necessary when used near children.

Use only as shown in this Manual. Use only Alto's recommended accessories.

Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the machine moving

parts.

Do not leave the machine unattended without being sure that it cannot move independently.

Do not use the machine on slopes with a gradient exceeding the speciﬁ cations.

Do not use the machine in particularly dusty areas.

While using this machine, take care not to cause damage to people or objects.

–

909 6315 000(2)2007-06 A SCRUBTEC 343E 5

USER MANUAL

ENGLISH

Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.

Do not put any can containing ﬂ uids on the machine.

The machine working temperature must be between 0°C and +40°C.

The machine storage temperature must be between 0°C and +40°C.

The humidity must be between 30% and 95%.

Do not use the machine as a means of transport.

Do not use the machine on slopes with a gradient exceeding the speciﬁ cations.

Do not allow the brush/pad to operate while the machine is stationary to avoid damaging the ﬂ oor.

In case of ﬁ re, use a powder ﬁ re extinguisher, not a water one.

Do not tamper with the machine safety guards and follow the ordinary maintenance instructions scrupulously.

Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged. Always keep

the openings free from dust, hairs and any other foreign material which could reduce the air ﬂ ow.

Do not remove or modify the plates afﬁ xed to the machine.

If the machine is used according to the instructions, the vibrations are not dangerous. The machine vibration level is

less than 2.5 m/s

2

(98/37/EEC-EN 1033/1995).

This machine cannot be used on roads or public streets.

Pay attention during machine transportation when temperature is below freezing point. The water in the recovery tank

or in the hoses could freeze and seriously damage the machine.

Use brushes and pads supplied with the machine and those speciﬁ ed in the User Manual. Using other brushes or

pads could reduce safety.

In case of machine malfunctions, ensure that these are not due to lack of maintenance. If necessary, request

assistance from the authorised personnel or from an authorised Service Center.

If the machine

does not work properly

is damaged

has water or foam leaks

has been left outdoors exposed to bad weather conditions

is wet or has been dropped into water

turn it off immediately and contact Alto Service Center or a qualiﬁ ed technician.

If parts must be replaced, require ORIGINAL spare parts from an Authorised Dealer or Retailer.

To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of this

Manual, must be performed by the authorised personnel or by an authorised Service Centre.

Carefully read all the instructions before performing any maintenance/repair procedure.

Do not wash the machine with direct or pressurised water jets, or with corrosive substances.

The machine must be disposed of properly, because of the presence of toxic-harmful materials (electronic

components, etc.), which are subject to standards that require disposal in special centres (see the Scrapping

chapter).

–

•

–

6 SCRUBTEC 343E 909 6315 000(2)2007-06 A

ENGLISH USER MANUAL

MACHINE DESCRIPTION

MACHINE STRUCTURE

Serial number plate/technical data/conformity certiﬁ cation

Handlebar

Handlebar inclination adjusting knob

Solution ﬂ ow control lever

5a. Minimum solution ﬂ ow position

5b. Maximum solution ﬂ ow position

Recovery water tank cover

Rear support wheel for transport/parking

Central wheels on ﬁ xed axle

Brush/pad

Brush/pad-holder deck

Squeegee

Squeegee mounting handwheels

Front squeegee blade

Rear squeegee blade

1.

2.

3.

4.

6.

7.

8.

9.

10.

11.

12.

13.

14.

Squeegee blade mounting springs

Recovery water drain hose

Recovery water drain hose bracket

Solution drain valve

Squeegee lifting/lowering lever

Solution ﬁ lter

Power supply cable

Squeegee vacuum hose

Transport/parking device

23a. Transport/parking device (engaged)

23b. Transport/parking device (disengaged)

Transport/parking device positioning pin

Brush/pad-holder support

Recovery water tank

Solution tank

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

27.

26

25

6

19

2

17

16

3

21

27

24

23

10 9

8

20

1

5a

5b

18

4

7

13

14

15

11

15

12

22

23a

23b

13 14

S311233A

909 6315 000(2)2007-06 A SCRUBTEC 343E 7

USER MANUAL

ENGLISH

49

38

39

46

41

45

40

37

36

34

31

32

48

47

35

33

42

43

44

S311236A

Recovery water tank cover (open)

Recovery water tank cover gasket

Brush/pad-holder support

Recovery water tank compartment

Solution tank ﬁ ller neck

Vacuum grid with automatic shut-off ﬂ oat

Recovery water drain hole

Vacuum system motor

Brush/pad-holder motor

Brush/pad-holder deck

Machine speed adjustment screw

Brush

Pad-holder

Pad

Terminal board box

Screw

Compensation hole

Cover support rod (engaged)

Brush/pad-holder engagement rotation direction

31.

32.

33.

34.

35.

36.

37.

38.

39.

40.

41.

42.

43.

44.

45.

46.

47.

48.

49.

MACHINE STRUCTURE (Continues)

8 SCRUBTEC 343E 909 6315 000(2)2007-06 A

ENGLISH USER MANUAL

CONTROL PANEL

Control panel

Brush/pad-holder switch

Vacuum system switch

1

2

3

S311232A

ACCESSORIES/OPTIONS

In addition to the standard components, the machine can be equipped with the following accessories/options, according to the

machine speciﬁ c use:

Brushes/pads of different materials

For further information concerning the optional accessories, contact an authorised Service Centre or Retailer.

TECHNICAL DATA

General

SCRUBTEC 343E

230 Volts

SCRUBTEC 343E

115 Volts

Machine length 1,120 mm

Machine width with squeegee 720 mm

Machine width without squeegee 570 mm

Min/max machine height with adjustable handlebar 860 - 1,105 mm

Total machine weight 75 kg

Minimum turning radius 750 mm

Cleaning width 430 mm

Central wheel diameter 250 mm

Brush/pad diameter 430 - 432 mm

Wheel on-ﬂ oor pressure 0.23 N/mm

2

Brush/pad pressure on the ﬂ oor 28 kg

Performance

SCRUBTEC 343E

230 Volts

SCRUBTEC 343E

115 Volts

Vacuuming 1,316 mmH

2

O

Brush/pad-holder motor speed 150 rpm 170 rpm

Sound pressure level at workstation 71 dB(A)

Vacuum system motor power 550 W

Brush/pad motor power 1,100 W 550 W

Gradeability 2%

System voltage 230 V - 50 Hz 115 V - 60 Hz

Clean water tank capacity 31 litres

Recovery water tank capacity 30 litres

51.

52.

53.

–

909 6315 000(2)2007-06 A SCRUBTEC 343E 9

USER MANUAL

ENGLISH

WIRING DIAGRAM

Key

C1 Suppressor

EV1 Water solenoid valve

FR Frame

M1 Brush/pad-holder motor

M2 Vacuum system motor

PL Plug

SW1 Brush/pad-holder switch

SW2 Vacuum system switch

Colour codes

BK Black

BU Blue

BN Brown

GN Green

GY Grey

OG Orange

PK Pink

RD Red

VT Violet

WH White

YE Yellow

S310239A

10 SCRUBTEC 343E 909 6315 000(2)2007-06 A

ENGLISH USER MANUAL

USE

WARNING!

On some points of the machine there are some adhesive plates indicating:

DANGER

WARNING

CAUTION

CONSULTATION

–

While reading this Manual, the operator must pay particular attention to the symbols shown on the plates.

Do not cover these plates for any reason and immediately replace them if damaged.

BEFORE MACHINE START-UP

Brush or pad-holder installation

NOTE

Use either the brush (42) or the pad-holder (43) according to the type of ﬂ oor to be cleaned.

Insert the positioning pin (24) and disengage the machine transport/parking device (23b).

Lift the brush/pad-holder deck (10) by prying the handlebar (2).

Place the brush (42) or the pad-holder (43) under the deck.

Lower the deck (10) by using the handlebar (2).

Connect the power supply cable (21) to the electrical mains.

Engage the brush/pad-holder by pressing the brush/pad switch (52) for a few seconds.

If the procedure is difﬁ cult, manually turn the brush/pad-holder counter-clockwise (49).

Brush/pad application guide (suggestions only)

Types of brushes available Midlite Grit 180 Midgrit 240 Prolite Union Mix

General cleaning:

Concrete

Terrazzo ﬂ oor

Ceramic tiles/quarrystones

Marble

Vinyl tiles

Rubber tiles

Polishing:

Rubber tiles

Marble

Vinyl tiles

Squeegee installation

Install the squeegee (11) and fasten it with the handwheels (12), then connect the vacuum hose (22) to the squeegee.

Solution tank ﬁ lling

Open the recovery water tank cover (41) and engage the support rod (59).

Use the ﬁ ller neck (35) to ﬁ ll the tank (27) with a solution suitable for the work to be performed.

Do not ﬁ ll the solution tank completely, leave a few centimetres from the edge.

Always follow the dilution instructions on the label of the chemical product used to prepare the solution.

The solution temperature must not exceed 40°C.

CAUTION!

Use only low-foam and non-ﬂ ammable detergents, intended for automatic scrubber applications.

Adjustments

Adjust the handlebar (2) with the knobs (3) to reach a comfortable position.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

909 6315 000(2)2007-06 A SCRUBTEC 343E 11

USER MANUAL

ENGLISH

MACHINE START AND STOP

Starting the machine

Prepare the machine as shown in the previous paragraph.

Drive the machine by pushing it with the hands on the handlebar (2).

Connect the power supply cable (21) to the electrical mains.

WARNING!

Before connecting the power supply cable to the electrical mains, check that frequency and voltage, shown

on the machine serial number plate (1), match the electrical mains voltage.

Lower the squeegee (11) with the lever (19).

Turn the solution ﬂ ow control lever (4) to a position between the minimum limit (5a) and maximum limit (5b). In no case it is

possible to close completely the water ﬂ ow to the brushes during operation.

While keeping the hand on the handlebar (2), start the machine by turning the brush/pad-holder switch and the vacuum system

switch (52 and 53) to "I".

Stopping the machine

Turn the brush/pad-holder switch and the vacuum system switch (52 and 53) to “0”.

Disconnect the power supply cable (21) from the electrical mains.

Lift the squeegee with the lever (19).

Insert the positioning pin (24) and lift the brush/pad-holder by engaging the transport/parking device (23a).

MACHINE OPERATION (SCRUBBING/DRYING)

Start the machine as shown in the previous paragraph.

While keeping both hands on the handlebar (2), maneuver the machine and start scrubbing/drying the ﬂ oor.

CAUTION!

To avoid damaging the ﬂ oor surface, do not use the brushes without the solution and, when the machine is

not operating, stop the brush/pad-holder by pressing the switch (52).

CAUTION!

Before lifting the brush/pad, turn it off by pressing the switch (52).

If necessary, vary the solution quantity by using the lever (4).

NOTE

For correct scrubbing/drying of ﬂ oors at the sides of the walls, Alto suggests to go near the walls with the right side of

the machine as shown in ﬁ gure 1.

B

A

Figure 1

P100160

Machine speed adjustment

The machine speed varies according to the type of ﬂ oor to be cleaned and the choice of using the brush or the pad.

If necessary, it is possible to adjust the machine speed, according to the procedure shown in Maintenance chapter.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

1.

2.

3.

4.

12 SCRUBTEC 343E 909 6315 000(2)2007-06 A

ENGLISH USER MANUAL

MACHINE TRANSPORT/PARKING

To transport/park the machine, proceed as follows.

Turn the brush/pad-holder switch and the vacuum system switch (52 and 53) to “0”.

Disconnect the power supply cable (21) from the electrical mains and place it on the holder.

Lift the squeegee with the lever (19).

Grasp the handlebar (2) and slightly lower it until the rear wheel (7) comes into contact with the ﬂ oor (Fig. 2). While holding the

machine in this position, push it to the transport/parking area.

In order not to drag the brush/pad on the ﬂ oor and leave wet marks, when ﬁ nishing working, remove the brush/pad-holder from

the deck by using the release device (see the procedure in After Using The Machine paragraph), then place it on the support

(25).

Figure 2

S310234

TANK EMPTYING

An automatic ﬂ oat shut-off system (36) turns off the vacuum system when the recovery water tank (26) is full.

The vacuum system shutdown, due to the recovery water tank ﬁ lling, is signalled by an increase in the vacuum system motor noise,

moreover the ﬂ oor is not dried.

CAUTION!

If the vacuum system turns off accidentally (for example, when the ﬂ oat is activated because of a sudden

machine movement), to resume the operation: turn off the vacuum system by pressing the switch (53), then

open the cover (6) and check that the ﬂ oat inside the grid (36) has gone down to the water level. Then close

the cover (6) and turn on the vacuum system by pressing the switch (53).

When the recovery water tank (26) is full, empty it according to the following procedure.

Recovery water tank emptying

Start the machine by pressing the brush/pad-holder and vacuum system switches (52 and 53).

Disconnect the power supply cable (21) from the electrical mains and place it on the holder.

Lift the squeegee with the lever (19).

Push the machine to the appointed disposal area.

Insert the positioning pin (24) and lift the brush/pad-holder by engaging the transport/parking device (23a).

Empty the recovery water tank (26) with the drain hose (16).

After working, rinse the tank with clean water.

Solution tank emptying

Perform steps 1 to 4.

Empty the solution tank (27) by using the drain valve (18).

After working, rinse the tank with clean water.

1.

2.

3.

4.

5.

1.

2.

3.

4.

5.

6.

7.

8.

909 6315 000(2)2007-06 A SCRUBTEC 343E 13

USER MANUAL

ENGLISH

AFTER USING THE MACHINE

After working, before leaving the machine:

Remove the brush/pad-holder as follows:

With the brush/pad-holder lifted, turn the brush/pad-holder switch (52) to “I” and, after a few seconds, back to “0”, thus

releasing the brush/pad-holder.

Disconnect the power supply cable (21) from the electrical mains and place it on the holder.

Empty the tanks (26 and 27) according to the procedure shown in the previous paragraph.

Perform the daily maintenance procedures (see the Maintenance chapter).

Store the machine in a clean and dry place, with the brush/pad-holder and the squeegee lifted or removed.

RECOVERY WATER TANK REMOVAL

To perform check and maintenance procedures, it may be necessary to remove the recovery water tank (26) as shown below.

Empty the recovery water tank (26) as shown in the relevant paragraph.

Drive the machine on a level ﬂ oor.

Make sure that the power supply cable (21) is disconnected from the electrical mains.

Disconnect the vacuum hose (22) from the squeegee (11).

Disconnect the recovery water drain hose (16) from the bracket (17).

Open the cover (6).

Grasp the recovery water tank (A, Fig. 3) in the area (B) and slightly raise it.

Disconnect the vacuum hose (C) from the tank, then remove the tank (A) with the hoses (D) and (E).

A

C

B

D

E

Figure 3

S311229A

MACHINE LONG INACTIVITY

If the machine is not going to be used for more than 30 days, proceed as follows:

Perform the procedures shown in After Using the Machine paragraph.

Store the machine in a clean and dry place.

FIRST PERIOD OF USE

After the ﬁ rst 8 hours, check the machine fastening and connecting parts for proper tightening. Check the visible parts for integrity

and leakage.

1.

•

2.

3.

4.

5.

1.

2.

3.

4.

5.

6.

7.

8.

1.

2.

14 SCRUBTEC 343E 909 6315 000(2)2007-06 A

ENGLISH USER MANUAL

MAINTENANCE

The lifespan of the machine and its maximum operating safety are ensured by correct and regular maintenance.

The following chart provides the scheduled maintenance. The intervals shown may vary according to particular working conditions,

which are to be deﬁ ned by the person in charge of the maintenance.

WARNING!

Maintenance procedures must be performed with the machine switched off and the power supply cable

disconnected from the electrical mains.

Moreover, carefully read the instructions in the Safety chapter.

All scheduled or extraordinary maintenance procedures must be performed by qualiﬁ ed personnel, or by an authorised Service

Centre.

This Manual describes only the easier and most common maintenance procedures.

NOTE

For other maintenance procedures shown in the Scheduled Maintenance Table, refer to the Service Manual that can

be consulted at any Service Center.

SCHEDULED MAINTENANCE TABLE

Procedure

Daily, after us-

ing the machine

Weekly

Every six

months

Yearly

Squeegee cleaning

Brush cleaning

Tank and vacuum grid cleaning

Squeegee blade check and replacement

Solution ﬁ lter cleaning

Screw and nut tightening check (1)

Vacuum system motor carbon brush check and replacement (2)

(1) And after the ﬁ rst 8 working hours.

(2) This maintenance procedure must be performed by Alto authorised Service Center.

909 6315 000(2)2007-06 A SCRUBTEC 343E 15

USER MANUAL

ENGLISH

SQUEEGEE CLEANING

NOTE

The squeegee must be clean and its blades must be in good conditions in order to get a good drying.

CAUTION!

It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris.

Drive the machine on a level ﬂ oor.

Make sure that the power supply cable (21) is disconnected from the electrical mains.

Lower the squeegee with the lever (19).

Disconnect the vacuum hose (22) from the squeegee.

Loosen the handwheels (12) and remove the squeegee (11).

Wash and clean the squeegee. In particular, clean the compartments (A, Fig. 4) and the vacuum hole (B) from dirt and debris.

Check the front blade (C) and the rear blade (D) for integrity, cuts and tears; if necessary replace them (see the procedure in

the following paragraph).

Assemble the components in the reverse order of disassembly.

SQUEEGEE BLADE CHECK AND REPLACEMENT

Clean the squeegee as shown in the previous paragraph.

Check that the front blade edges (E, Fig. 4) and the rear blade edges (I) lay down on the same level, along their length; if

necessary adjust the height according to the following procedure:

Remove the mounting springs (F), then adjust the front blade (C) and the rear blade (D).

Install the mounting springs on the front and rear blades.

Check the front blade (C) and rear blade (D) for integrity, cuts and tears; if necessary replace them as shown below. Also

check the front corner (H) of the rear blade for wear; if it is worn, overturn the blade to replace the worn corner with the other

one (I), if it is integral. If the other corner is worn too, replace the blade according to the following procedure:

Remove the mounting springs (F) and then replace (or overturn) the rear blade (D).

Install the mounting springs on the front and rear blades.

Install the squeegee (11) and screw tighten the handwheels (12).

Connect the vacuum hose (22) to the squeegee (11).

5 9

12

7

1

2

1

6

4

3

Figure 4

S310240

1.

2.

3.

4.

5.

6.

7.

8.

1.

2.

•

3.

•

4.

5.

16 SCRUBTEC 343E 909 6315 000(2)2007-06 A

ENGLISH USER MANUAL

BRUSH CLEANING

NOTE

It is advisable to wear protective gloves when cleaning the brushes because there may be sharp debris.

Remove the brush, as shown in Use chapter.

Clean and wash the brush with water and solution.

Check the brush bristles for integrity and wear; if necessary, replace the brush.

TANK AND VACUUM GRID CLEANING

Push the machine to the appointed disposal area.

Make sure that the power supply cable (21) is disconnected from the electrical mains.

Open the cover (6), then clean and wash the cover, the tanks (26 and 27) and the vacuum grid (36) with clean water.

Drain the water from the tanks with the drain hose (16) and the valve (18).

If necessary, release the fasteners (B, Fig. 5) and open the grid (A); recover the ﬂ oat (C), clean all the components and then

reinstall them.

Check the recovery water tank cover sealing gasket (D) for integrity.

NOTE

The gasket (D) creates vacuum in the tank that is necessary for vacuuming the recovery water.

If necessary replace the gasket (D) by removing it from its housing (E).

When assembling the new gasket, install the joint (F) in the rear central area, as shown in the ﬁ gure.

Check the bearing surface (D) of the gasket (G) for integrity and sealing capabilities.

Check that the compensation hole (47) is not clogged.

NOTE

The hole (47), allowing to compensate the air in the cover air gap, contributes to create vacuum in the tank.

Close the recovery water tank cover (6).

C

B

A

D

F

G

E

Figure 5

S311227A

1.

2.

3.

1.

2.

3.

4.

5.

6.

7.

8.

909 6315 000(2)2007-06 A SCRUBTEC 343E 17

USER MANUAL

ENGLISH

SOLUTION FILTER CLEANING

Empty the solution tank (27) as shown in the relevant paragraph.

Drive the machine on a level ﬂ oor.

Make sure that the power supply cable (21) is disconnected from the electrical mains.

Remove the transparent cover (A, Fig. 6), then remove the ﬁ lter strainer (B). Clean and install them on the support (C).

NOTE

The ﬁ lter strainer (B) must be correctly positioned on the housing (D) of the support (C).

C

B

A

B

D

Figure 6

S310232A

MACHINE SPEED ADJUSTMENT

NOTE

The machine speed varies according to the type of ﬂ oor to be cleaned and the choice of using the brush or the pad.

If necessary, perform the following procedure.

Remove the recovery water tank as shown in Use chapter.

Adjust the machine speed with the screw (41) as shown below:

Loosen the screw (46), on the right side of the machine, by turning it counter-clockwise.

Rotate the adjusting screw (41) counter-clockwise to increase the machine speed.

Turn the adjusting screw (41) clockwise to decrease the machine speed.

After adjusting, tighten the screw (46).

Install the recovery water tank as shown in Use chapter.

With the machine ready to operate, perform hands-on tests of the machine and, if other adjustments are necessary, repeat

steps 1 to 4.

1.

2.

3.

4.

1.

2.

•

3.

4.

18 SCRUBTEC 343E 909 6315 000(2)2007-06 A

ENGLISH USER MANUAL

TROUBLESHOOTING

Trouble Possible Cause Remedy

The motors do not turn on.

The power supply cable (21) is faulty or

disconnected from the electrical mains.

Replace the cable or connect it.

The dirty water vacuuming is insufﬁ cient.

The recovery water tank (26) is full. Empty.

The vacuum grid (36) is clogged or the ﬂ oat

is closing.

Clean the grid and check the ﬂ oat.

The vacuum hose (22) is disconnected from

the squeegee (11) or it is damaged.

Connect.

The squeegee (11) is dirty, or the squeegee

blades (13 - 14) are worn or damaged.

Clean the squeegee or replace the blades.

The recovery water tank cover (6) is not

properly closed, or the gasket (32) is

damaged.

Check and/or clean the seating surface or

replace the gasket.

The recovery water tank (6) is dirty (clogged

drain hole).

Clean.

The solution ﬂ ow is insufﬁ cient. The solution ﬁ lter (20) is dirty. Clean.

The squeegee leaves marks on the ﬂ oor.

There is debris under the squeegee blades

(13 - 14).

Remove the debris.

The squeegee blades (13 - 14) are worn,

chipped or torn.

Replace the blades.

For further information refer to the Service Manual, available at any Alto Service Center.

SCRAPPING

Have the machine scrapped by a qualiﬁ ed scrapper.

Before scrapping the machine, remove and separate the following materials, which must be disposed of properly according to the

Law in force:

Brush

Pad

Electrical and electronic components (*)

(*) Refer to the nearest Alto Center especially when scrapping electrical and electronic components.

–

Page is loading ...

Nilfisk-ALTO SCRUBTEC 343E User manual

Nilfisk-ALTO SCRUBTEC 343E User manual

in other languages

Related papers

Other documents