Nilfisk-ALTO SCRUBTEC 653 User manual

Page is loading ...

EC Machinery Directive 2006/42/EC EN ISO 12100-1, EN ISO 12100-2, EN 294, EN 349, EN 982

EC Low Voltage Directive 2006/95/EC EN 60335-1, EN 60335-2-72, EN 50366

EC EMC Directive 2004/108/EC EN 55014-1, EN 55014-2

Manufacturer: Nilﬁsk-Advance S.p.a.

Authorized signatory: Franco Mazzini, General Mgr

Date: Signature:

Address: Strada Comunale della Braglia, 18, 26862 GUARDAMIGLIO (LO) - ITALY

Tel: +39 (0)377 451124, Fax: +39 (0)377 51443

nery D

w Voltage Dir

MC Directive 200

tive 2006/42/

ve 2006/95

8/EC

Долуподписаният потвърждава, че

гореспоменатият модел е произведен в

съответствие със следните директиви и

стандарти.

Níže podepsaný stvrzuje, že výše

uvedený model byl vyroben v souladu s

následujícími směrnicemi a normami.

Der Unterzeichner bestätigt hiermit dass

die oben erwähnten Modelle gemäß

den folgenden Richtlinien und Normen

hergestellt wurden.

Undertegnede attesterer herved, at

ovennævnte model er produceret i

overensstemmelse med følgende direktiver

og standarder.

El abajo ﬁrmante certiﬁca que los modelos

arriba mencionados han sido producidos

de acuerdo con las siguientes directivas y

estandares.

Allakirjutanu kinnitab, et ülalnimetatud

mudel on valmistatud kooskõlas järgmiste

direktiivide ja normidega.

Je soussigné certiﬁe que les modèles ci-

dessus sont fabriqués conformément aux

directives et normes suivantes.

Allekirjoittaia vakuuttaa että yllämainittu

malli on tuotettu seuraavien direktiivien ja

standardien mukaan.

The undersigned certify that the above

mentioned model is produced in

accordance with the following directives

and standards.

Ο κάτωθι υπογεγραμμένος πιστοποιεί ότι η

παραγωγή του προαναφερθέντος μοντέλου

γίνεται σύμφωνα με τις ακόλουθες οδηγίες

και πρότυπα.

Alulírottak igazoljuk, hogy a fent említett

modellt a következő irányelvek és

szabványok alapján hoztuk létre.

Il sottoscritto dichiara che i modelli sopra

menzionati sono prodotti in accordo con le

seguenti direttive e standard.

Toliau pateiktu dokumentu patvirtinama,

kad minėtas modelis yra pagamintas

laikantis nurodytų direktyvų bei standartų.

Ar šo tiek apliecināts, ka augstākminētais

modelis ir izgatavots atbilstoši šādām

direktīvām un standartiem.

Undertegnede attesterer att ovennevnte

modell är produsert i overensstemmelse

med fölgende direktiv og standarder.

Ondergetekende verzekert dat de

bovengenoemde modellen geproduceerd

zijn in overeenstemming met de volgende

richtlijnen en standaards.

A presente assinatura serve para declarar

que os modelos supramencionados

são produtos em conformidade com as

seguintes directivas e normas.

Niżej podpisany zaświadcza, że

wymieniony powyżej model produkowany

jest zgodnie z następującymi dyrektywami

i normami.

Subsemnatul atest că modelul sus-

menţionat este produs în conformitate cu

următoarele directive şi standarde.

Настоящим удостоверяется, что машина

вышеуказанной модели изготовлена

в соответствии со следующими

директивами и стандартами.

Undertecknad intygar att ovannämnda

modell är producerad i överensstämmelse

med följande direktiv och standarder.

Dolu podpísaný osvedčuje, že hore

uvedený model sa vyrába v súlade s

nasledujúcimi smernicami a normami.

Spodaj podpisani potrjujem, da je zgoraj

omenjeni model izdelan v skladu z

naslednjimi smernicami in standardi.

Aşağıda İmzası olan kişi, yukarıda

bahsedilen model cihazın aşağıda verilen

direktiﬂere ve standartlara uygunlukta imal

edildiğini onaylar.

Модел / Model / Modell / Model / Modelo / Mudel / Modèle / Malli /

Model / Μοντέλο / Modell / Modello / Modelis / Modelis / Modell / Model

/ Modelo / Model / Model / Модель / Modell / Model / Model / Model :

SCRUBTEC 653B – 653BL – 651BCL – 661BL

Тип / Typ / Typ / Type / Tipo / Tüüp / Type / Tyyppi / Type / Τύπος /

Típus / Tipo / Tipas / Tips / Type / Type / Tipo / Typ / Tip / Тип / Typ /

Typ / Tip / Tip :

SCRUBBER-DRYER

Сериен номер / Výrobní číslo / Seriennummer / Serienummer / Número de serie / Seerianumber / Numéro de série / Sarjanumero / Serial number

/ Σειριακός αριθμός / Sorozatszám / Numero di serie / Serijos numeris / Sērijas numurs / Serienummer / Serienummer / Número de série / Numer

seryjny / Număr de serie / Серийный номер / Serienummer / Výrobné číslo / Serijska številka / Seri Numarası :

Година на производство / Rok výroby / Baujahr / Fabrikationsår / Año de fabricación / Väljalaskeaasta / Année de fabrication / Valmistusvuosi / Year

of construction / Έτος κατασκευής / Gyártási év / Anno di costruzione / Pagaminimo metai / Izgatavošanas gads / Byggeår / Bauwjaar / Ano de fabrico

/ Rok produkcji / Anul fabricaţiei / Год выпуска / Tillverkningsår / Rok výroby / Leto izdelave / Leto izdelave/İmal yılı :

Сертификат за съответствие

Osvědčení o shodě

Konformitätserklärung

Overensstemmelsescertiﬁkat

Declaración de conformidad

Vastavussertiﬁkaat

Déclaration de conformité

Yhdenmukaisuustodistus

Conformity certiﬁcate

Πιστοποιητικό συμμόρφωσης

Megfelelősségi nyilatkozat

Dichiarazione di conformità

Atitikties deklaracija

Atbilstības deklarācija

Konformitetssertiﬁsering

Conformiteitsverklaring

Declaração de conformidade

Deklaracja zgodności

Certiﬁcat de conformitate

Заявление о соответствии

Överensstämmelsecertiﬁkat

Certiﬁkát súladu

Certiﬁkat o ustreznosti

Uyumluluk sertiﬁkası

Page is loading ...

9097058000(2)2009-10 A SCRUBTEC 653B – 653BL – 651BCL – 661BL 1

MANUEL OPERATEUR

FRANÇAIS

TABLE DES MATIERES

INTRODUCTION .............................................................................................................................................................. 2

BUT ET CONTENU DU MANUEL ................................................................................................................................................... 2

DESTINATAIRES ............................................................................................................................................................................. 2

CONSERVATION DU MANUEL ....................................................................................................................................................... 2

DECLARATION DE CONFORMITE ................................................................................................................................................ 2

DONNEES D’IDENTIFICATION ...................................................................................................................................................... 2

AUTRES MANUELS DE REFERENCE ........................................................................................................................................... 2

PIECES DE RECHANGE ET ENTRETIEN ..................................................................................................................................... 2

MODIFICATIONS ET AMELIORATIONS ......................................................................................................................................... 3

CAPACITES OPERATIONNELLES ................................................................................................................................................. 3

CONVENTIONS .............................................................................................................................................................................. 3

DEBALLAGE / LIVRAISON ............................................................................................................................................. 3

SECURITE ....................................................................................................................................................................... 3

SYMBOLES UTILISES .................................................................................................................................................................... 3

INSTRUCTIONS GENERALES ....................................................................................................................................................... 4

DESCRIPTION DE LA MACHINE ................................................................................................................................... 6

STRUCTURE DE LA MACHINE ...................................................................................................................................................... 6

TABLEAU DE BORD ....................................................................................................................................................................... 8

HUBLOT DE LECTURE DES DONNEES DU CHARGEUR DE BATTERIE (optionnel) ................................................................. 8

ACCESSOIRES / OPTIONS ............................................................................................................................................................ 9

CARACTERISTIQUES TECHNIQUES ............................................................................................................................................ 9

SCHEMA ELECTRIQUE (SCRUBTEC 653B) ................................................................................................................................11

SCHEMA ELECTRIQUE (SCRUBTEC 653BL, SCRUBTEC 651BCL, SCRUBTEC 661BL) ........................................................ 12

UTILISATION ................................................................................................................................................................. 13

CONTROLE / PREPARATION DES BATTERIES SUR UNE MACHINE NEUVE ......................................................................... 13

INSTALLATION DES BATTERIES ET CONFIGURATION DU TYPE DE BATTERIES (WET OU GEL) ....................................... 14

AVANT LA MISE EN MARCHE DE LA MACHINE ......................................................................................................................... 15

MISE EN MARCHE ET ARRET DE LA MACHINE ........................................................................................................................ 18

MACHINE AU TRAVAIL (LAVAGE / SECHAGE) ........................................................................................................................... 19

VIDANGE DES RESERVOIRS ...................................................................................................................................................... 21

APRES L’UTILISATION DE LA MACHINE .................................................................................................................................... 21

INACTIVITE PROLONGEE DE LA MACHINE .............................................................................................................................. 21

PREMIERE PERIODE D’UTILISATION ......................................................................................................................................... 21

ENTRETIEN ................................................................................................................................................................... 22

PLAN D’ENTRETIEN PROGRAMME ............................................................................................................................................ 22

CHARGEMENT DES BATTERIES ................................................................................................................................................ 23

CONTROLE DES HEURES DE TRAVAIL DE LA MACHINE ........................................................................................................ 24

NETTOYAGE DE L’EMBOUCHURE ............................................................................................................................................. 24

CONTROLE ET REMPLACEMENT DES LAMELLES EN CAOUTCHOUC DE L’EMBOUCHURE .............................................. 25

NETTOYAGE DES BROSSES / DISQUES ................................................................................................................................... 26

NETTOYAGE DU FILTRE DU MOTEUR DU SYSTEME D’ASPIRATION ..................................................................................... 26

NETTOYAGE DU FILTRE DE LA SOLUTION / DE L’EAU PROPRE ............................................................................................ 26

NETTOYAGE DES RESERVOIRS, DE LA GRILLE D’ASPIRATION AVEC FLOTTEUR ET CONTROLE DU JOINT

D’ETANCHEITE DU COUVERCLE ............................................................................................................................................... 27

CONTROLE / REMPLACEMENT DES FUSIBLES ....................................................................................................................... 28

DEPOSE / REPOSE DE LA TETE PORTE-BROSSES / PLATEAUX SUPPORT DISQUE / PORTE-BROSSES

CYLINDRIQUES ............................................................................................................................................................................ 29

NETTOYAGE DU RESERVOIR DU DETERGENT ....................................................................................................................... 29

DEPISTAGE DES PANNES ........................................................................................................................................... 30

MISE A LA FERRAILLE ................................................................................................................................................. 30

Page is loading ...

9097058000(2)2009-10 A SCRUBTEC 653B – 653BL – 651BCL – 661BL 1

USER MANUAL

ENGLISH

TABLE OF CONTENTS

INTRODUCTION .............................................................................................................................................................. 2

MANUAL PURPOSE AND CONTENTS .......................................................................................................................................... 2

TARGET ........................................................................................................................................................................................... 2

HOW TO KEEP THIS MANUAL ....................................................................................................................................................... 2

DECLARATION OF CONFORMITY ................................................................................................................................................ 2

IDENTIFICATION DATA ................................................................................................................................................................... 2

OTHER REFERENCE MANUALS ................................................................................................................................................... 2

SPARE PARTS AND MAINTENANCE ............................................................................................................................................. 2

CHANGES AND IMPROVEMENTS ................................................................................................................................................ 3

OPERATION CAPABILITIES ........................................................................................................................................................... 3

CONVENTIONS .............................................................................................................................................................................. 3

UNPACKING/DELIVERY ................................................................................................................................................. 3

SAFETY ........................................................................................................................................................................... 3

SYMBOLS ....................................................................................................................................................................................... 3

GENERAL INSTRUCTIONS ............................................................................................................................................................ 4

MACHINE DESCRIPTION ............................................................................................................................................... 6

MACHINE STRUCTURE ................................................................................................................................................................. 6

CONTROL PANEL ........................................................................................................................................................................... 8

BATTERY CHARGER DATA INSPECTION WINDOW (optional) .................................................................................................... 8

ACCESSORIES/OPTIONS .............................................................................................................................................................. 9

TECHNICAL DATA ........................................................................................................................................................................... 9

WIRING DIAGRAM (SCRUBTEC 653B) ........................................................................................................................................11

WIRING DIAGRAM (SCRUBTEC 653BL, SCRUBTEC 651BCL, SCRUBTEC 661BL) ................................................................ 12

USE ................................................................................................................................................................................ 13

BATTERY CHECK/SETTING ON A NEW MACHINE .................................................................................................................... 13

BATTERY INSTALLATION AND BATTERY TYPE SETTING (WET OR GEL) .............................................................................. 14

BEFORE MACHINE START-UP .................................................................................................................................................... 15

MACHINE START AND STOP ....................................................................................................................................................... 18

MACHINE OPERATION (SCRUBBING/DRYING) ......................................................................................................................... 19

TANK EMPTYING .......................................................................................................................................................................... 21

AFTER USING THE MACHINE ..................................................................................................................................................... 21

MACHINE LONG INACTIVITY ...................................................................................................................................................... 21

FIRST PERIOD OF USE ............................................................................................................................................................... 21

MAINTENANCE ............................................................................................................................................................. 22

SCHEDULED MAINTENANCE TABLE ......................................................................................................................................... 22

BATTERY CHARGING .................................................................................................................................................................. 23

MACHINE WORKING HOUR CHECK .......................................................................................................................................... 24

SQUEEGEE CLEANING ............................................................................................................................................................... 24

SQUEEGEE BLADE CHECK AND REPLACEMENT .................................................................................................................... 25

BRUSH/PAD CLEANING ............................................................................................................................................................... 26

VACUUM SYSTEM MOTOR FILTER CLEANING ......................................................................................................................... 26

SOLUTION/CLEAN WATER FILTER CLEANING ......................................................................................................................... 26

TANK AND VACUUM GRID WITH FLOAT CLEANING, AND COVER GASKET CHECK ............................................................. 27

FUSE CHECK/REPLACEMENT .................................................................................................................................................... 28

BRUSH/PAD-HOLDER/CYLINDRICAL BRUSH DECK DISASSEMBLY/ASSEMBLY .................................................................. 29

DETERGENT TANK CLEANING ................................................................................................................................................... 29

TROUBLESHOOTING ................................................................................................................................................... 30

SCRAPPING .................................................................................................................................................................. 30

2 SCRUBTEC 653B – 653BL – 651BCL – 661BL 9097058000(2)2009-10 A

ENGLISH USER MANUAL

INTRODUCTION

NOTE

The numbers in brackets refer to the components shown in Machine Description chapter.

MANUAL PURPOSE AND CONTENTS

The purpose of this Manual is to provide the operator with all necessary information to use the machine properly, in a safe and

autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal.

Before performing any procedure on the machine, the operators and qualiﬁ ed technicians must read this Manual carefully. Contact

Nilﬁ sk Alto in case of doubts concerning the interpretation of the instructions and for any further information.

TARGET

This Manual is intended for operators and technicians qualiﬁ ed to perform the machine maintenance.

The operators must not perform procedures reserved for qualiﬁ ed technicians. Nilﬁ sk Alto will not be answerable for damages

coming from the non-observance of this prohibition.

HOW TO KEEP THIS MANUAL

The User Manual must be kept near the machine, inside an adequate case, away from liquids and other substances that can cause

damage to it.

DECLARATION OF CONFORMITY

The Declaration of Conformity, supplied with the machine, certiﬁ es the machine conformity with the law in force.

NOTE

Two copies of the original declaration of conformity are provided together with the machine documentation.

IDENTIFICATION DATA

The machine model and serial number are marked on the plate (34).

The machine production year is written in the declaration of conformity and it is also indicated by the ﬁ rst two ﬁ gures of the machine

serial number.

This information is useful when requiring machine spare parts. Use the following table to write down the machine identiﬁ cation data.

MACHINE model ...............................................................................

MACHINE serial number ...................................................................

OTHER REFERENCE MANUALS

Electronic Battery Charger Manual (if equipped), to be considered as integral part of this Manual –

Moreover, the following Manuals are available:

Service Manual (that can be consulted at Nilﬁ sk Alto Service Centers) –

Spare Parts List (supplied with the machine) –

SPARE PARTS AND MAINTENANCE

All necessary operating, maintenance and repair procedures must be performed by qualiﬁ ed personnel or by Alto Service Centers.

Only original spare parts and accessories must be used.

Contact Nilﬁ sk Alto for service or to order spare parts and accessories, specifying the machine model and serial number.

9097058000(2)2009-10 A SCRUBTEC 653B – 653BL – 651BCL – 661BL 3

USER MANUAL

ENGLISH

CHANGES AND IMPROVEMENTS

Nilﬁ sk Alto constantly improves its products and reserves the right to make changes and improvements at its discretion without

being obliged to apply such beneﬁ ts to the machines that were previously sold.

Any change and/or addition of accessories must be approved and performed by Nilﬁ sk Alto.

OPERATION CAPABILITIES

These scrubber-dryers are used to clean (scrubbing and drying) smooth and solid ﬂ oors, in civil or industrial environment, under

safe operation conditions by a qualiﬁ ed operator.

The scrubber-dryers cannot be used for ﬁ tted carpet and carpet cleaning.

CONVENTIONS

Forward, backward, front, rear, left or right are intended with reference to the operator’s position, that is to say in driving position

with the hands on the handlebar (2).

UNPACKING/DELIVERY

To unpack the machine, carefully follow the instructions on the packing.

When the machine is delivered, check that the packing and the machine were not damaged during transportation. In case of visible

damages, keep the packing and have it checked by the carrier that delivered it. Call the carrier immediately to ﬁ ll in a damage claim.

Check that the machine is equipped with the following features:

Technical documents:1.

Scrubber-dryer User Manual•

Electronic Battery Charger Manual (if equipped)•

Scrubber-dryer Spare Parts List•

No. 1 connector for battery charger (for machines without on board battery charger)2.

No. 2 lamellar fuses3.

SAFETY

The following symbols indicate potentially dangerous situations. Always read this information carefully and take all necessary

precautions to safeguard people and property.

The operator’s cooperation is essential in order to prevent injury. No accident prevention program is effective without the total

cooperation of the person responsible for the machine operation. Most of the accidents that may occur in a factory, while working

or moving around, are caused by failure to comply with the simplest rules for exercising prudence. A careful and prudent operator is

the best guarantee against accidents and is essential for successful completion of any prevention program.

SYMBOLS

DANGER!

It indicates a dangerous situation with risk of death for the operator.

WARNING!

It indicates a potential risk of injury for people or damage to objects.

CAUTION!

It indicates a caution or a remark related to important or useful functions. Pay careful attention to the

paragraphs marked by this symbol.

NOTE

It indicates a remark related to important or useful functions.

CONSULTATION

It indicates the necessity to refer to the User Manual before performing any procedure.

4 SCRUBTEC 653B – 653BL – 651BCL – 661BL 9097058000(2)2009-10 A

ENGLISH USER MANUAL

GENERAL INSTRUCTIONS

Speciﬁ c warnings and cautions to inform about potential damages to people and machine are shown below.

DANGER!

Before performing any cleaning, maintenance, repair or replacement procedure disconnect the battery –

connector and remove the ignition key.

This machine must be used by properly trained operators only. Children or disabled people cannot use this –

machine.

Keep the battery away from sparks, ﬂ ames and incandescent material. During the normal operation explosive –

gases are released.

Do not wear jewels when working near electrical components. –

Do not work under the lifted machine without supporting it with safety stands. –

Do not operate the machine near toxic, dangerous, ﬂ ammable and/or explosive powders, liquids or vapours: –

This machine is not suitable for collecting dangerous powders.

Battery charging produces highly explosive hydrogen gas. Keep the tank assembly open during battery –

charging and perform this procedure in well-ventilated areas and away from naked ﬂ ames.

WARNING!

Carefully read all the instructions before performing any maintenance/repair procedure. –

Before using the battery charger, ensure that frequency and voltage values, indicated on the machine serial –

number plate, match the electrical mains voltage.

Do not pull or carry the machine by the battery charger cable and never use the battery charger cable as –

a handle. Do not close a door on the battery charger cable, or pull the battery charger cable around sharp

edges or corners. Do not run the machine on the battery charger cable.

Keep the battery charger cable away from heated surfaces. –

Do not use the machine if the battery charger cable or plug is damaged. If the machine is not working as it –

should, has been damaged, left outdoors or dropped into water, return it to the Service Center.

To reduce the risk of ﬁ re, electric shock, or injury, do not leave the machine unattended when it is plugged –

in. Before performing any maintenance procedure, disconnect the battery charger cable from the electrical

mains.

Do not smoke while charging the batteries. –

Do not allow to be used as a toy. Close attention is necessary when used near children. –

Use only as shown in this Manual. Use only Nilﬁ sk Alto’s recommended accessories. –

Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the machine –

moving parts.

To avoid any unauthorised use of the machine, remove the ignition key (if equipped). –

Do not leave the machine unattended without being sure that it cannot move independently. –

9097058000(2)2009-10 A SCRUBTEC 653B – 653BL – 651BCL – 661BL 5

USER MANUAL

ENGLISH

WARNING!

Do not use the machine on slopes with a gradient exceeding the speciﬁ cations. –

Do not use the machine in particularly dusty areas. –

While using this machine, take care not to cause damage to people or objects. –

Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects. –

Do not lean liquid containers on the machine, use the relevant can holder. –

The machine working temperature must be between 0°C and +40°C. –

The machine storage temperature must be between 0°C and +40°C. –

The humidity must be between 30% and 95%. –

Always protect the machine against the sun, rain and bad weather, both under operation and inactivity –

condition. Store the machine indoors, in a dry place: This machine must be used in dry conditions, it must

not be used or kept outdoors in wet conditions.

Before using the machine, close all doors and/or covers. –

When using ﬂ oor cleaning detergents, follow the instructions on the labels of the detergent bottles. –

To handle ﬂ oor cleaning detergents, wear suitable gloves and protections. –

Do not use the machine as a means of transport. –

Do not allow the brushes to operate while the machine is stationary to avoid damaging the ﬂ oor. –

In case of ﬁ re, use a powder ﬁ re extinguisher, not a water one. –

Do not tamper with the machine safety guards and follow the ordinary maintenance instructions –

scrupulously.

Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged. –

Always keep the openings free from dust, hairs and any other foreign material which could reduce the air

ﬂ ow.

Do not remove or modify the plates afﬁ xed to the machine. –

This machine cannot be used on roads or public streets. –

Pay attention during machine transportation when temperature is below freezing point. The water in the –

recovery tank or in the hoses could freeze and seriously damage the machine.

Use brushes and pads supplied with the machine and those speciﬁ ed in the User Manual. Using other –

brushes or pads could reduce safety.

In case of machine malfunctions, ensure that these are not due to lack of maintenance. Otherwise, request –

assistance from the authorised personnel or from an authorised Service Center.

If parts must be replaced, require ORIGINAL spare parts from an Authorised Dealer or Retailer. –

To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of –

this Manual, must be performed by the authorised personnel or by an authorised Service Center.

Do not wash the machine with direct or pressurised water jets, or with corrosive substances. –

The machine must be disposed of properly, because of the presence of toxic-harmful materials (batteries, –

etc.), which are subject to standards that require disposal in special centres (see Scrapping chapter).

6 SCRUBTEC 653B – 653BL – 651BCL – 661BL 9097058000(2)2009-10 A

ENGLISH USER MANUAL

MACHINE DESCRIPTION

MACHINE STRUCTURE

Control panel4.

Handlebar5.

Brush/forward gear switch (*). Brush switch (***)6.

Drive speed adjuster (*)7.

Battery charger data inspection window (optional)8.

Battery charger cable (optional)9.

Battery charger cable holder (optional)10.

Recovery water drain hose plug11.

Reverse gear switch12.

Squeegee lifting/lowering lever13.

Deck lifting/lowering pedal14.

Pedal position when deck is lifted11a.

Pedal position when deck is lowered11b.

Extra pressure activation (optional)11c.

Battery connector (red). This connector also works as 15.

EMERGENCY push-button, to stop immediately all

functions.

Rear steering wheel16.

Front wheels on ﬁ xed axle. Driving wheels (*)17.

Squeegee vacuum hose18.

Recovery water drain hose19.

Solution/clean water drain and level check hose20.

Deck with one brush/pad-holder18a.

Deck with two brushes/pad-holders18b.

Deck with two cylindrical brushes18c.

Brushes/pad-holders19a.

Cylindrical brushes19b.

Solution/clean water tank21.

Recovery tank22.

Recovery tank cover23.

Can holder24.

Solenoid valve25.

Squeegee26.

Squeegee mounting handwheels27.

Squeegee adjusting handwheel28.

Machine straight forward movement adjusting handwheel29.

Machine forward speed adjusting handwheel (***)30.

Recovery tank cover31.

Tank cover gasket32.

Cover movable retaining plate33.

Cover ﬁ xed retaining plate (do not remove!)34.

Serial number plate/technical data/conformity certiﬁ cation35.

Squeegee bumper wheel36.

Vacuum grid with automatic shut-off ﬂ oat37.

Solution/clean water front ﬁ ller neck38.

Filter39.

Brush bumper wheels40.

Recovery water tank (opened)41.

Solution/clean water rear ﬁ ller neck42.

Tank safety cable43.

Vacuum system motor cover44.

Vacuum system motor sound-deadening ﬁ lter45.

Detergent tank (**)46.

Detergent tank plug (**)47.

Detergent tank handle (**)48.

Detergent feed hose (**)49.

Detergent pump (**)50.

Detergent tank - pump connecting hose (**)51.

Detergent pump holder (**)52.

Batteries53.

Battery caps54.

Solution/clean water ﬁ lter55.

Solution/clean water tap56.

Reference table for detergent proportioning (**)57.

Battery connection diagram58.

Only for SCRUBTEC 653BL, SCRUBTEC 651BCL, (*)

SCRUBTEC 661BL

Only for machines with Chemical Mixing System (optional)(**)

Only for SCRUBTEC 653B(***)

Page is loading ...

8 SCRUBTEC 653B – 653BL – 651BCL – 661BL 9097058000(2)2009-10 A

ENGLISH USER MANUAL

CONTROL PANEL

Brush/pad-holder switch71.

Brush/pad-holder switch warning light72.

Vacuum system switch73.

Vacuum system switch warning light74.

Brush/pad-holder release switch75.

Brush/pad-holder release switch warning light76.

Detergent ﬂ ow control knob (**)77.

Reverse gear switch (*)78.

Hour counter (optional)79.

Ignition key (0 - I)80.

Battery charge indicator81.

Charged battery warning light (green)81a.

Semi-discharged battery warning light (yellow)81b.

Discharged battery warning light (red)81c.

Washing water ﬂ ow control switches82.

Flow increase switch82a.

Flow decrease switch82b.

Washing water ﬂ ow indicator82c.

Brush/forward gear switch (*). Brush switch (***)83.

Speed adjuster (*)84.

Only for SCRUBTEC 653BL, SCRUBTEC 651BCL, (*)

SCRUBTEC 661BL

Only for machines with Chemical Mixing System (optional)(**)

Only for SCRUBTEC 653B(***)

71

82

82b 82c 82a

81a

81b

81c

81

72 74 73 76 75 79 80 83

SCRUBTEC 653B

71

82

82b 82c 77 7882a

81a

81b

81c

81

72 74 73 76 75 79 80 83

SCRUBTEC 653 BL - SCRUBTEC 653 BCL

SCRUBTEC 661 BL

84

P100116 P100117

BATTERY CHARGER DATA INSPECTION WINDOW (optional)

Electronic battery charger90.

Lead (WET) or gel (GEL) battery selector91.

Green warning light (ON: the battery charger is on and batteries are charged)92.

Yellow warning light (ON: the battery charger is on and batteries are semi-discharged)93.

Red warning light (ON: the battery charger is on and it is charging the batteries)94.

90

94

93

92

91

P100104

9097058000(2)2009-10 A SCRUBTEC 653B – 653BL – 651BCL – 661BL 9

USER MANUAL

ENGLISH

ACCESSORIES/OPTIONS

In addition to the standard components, the machine can be equipped with the following accessories/options, according to the

machine speciﬁ c use:

GEL batteries1.

Electronic battery charger2.

Brushes and cylindrical brushes of different materials3.

Pads of different materials4.

Polyurethane squeegee blades5.

Chemical Mixing System6.

Front and rear wheels of different materials7.

Hour counter8.

For further information concerning the optional accessories, contact an authorised Retailer.

TECHNICAL DATA

General technical data

Model

SCRUBTEC 653B

(1 brush/pad-holder,

without drive system)

SCRUBTEC 653BL

(1 brush/pad-holder,

with drive system)

SCRUBTEC 651BCL

(2 cylindrical brushes,

with drive system)

SCRUBTEC 661BL

(2 brushes/pad-

holders, with drive

system)

Machine height 1,088 mm

Solution/clean water tank capacity 55 litres

Recovery tank capacity 55 litres

Front wheel diameter 250 mm

Front and rear wheel speciﬁ c pressure on the ﬂ oor

0.8 N/mm

2

2.8 N/mm

2

0.8 N/mm

2

6.1 N/mm

2

Rear wheel diameter 100 mm

Vacuum system motor power 330 W

Drive system motor power — 200 W

Drive speed (variable) — 0 to 5.6 km/h

Gradeability 2%

Sound pressure level at workstation (ISO 11201,

ISO 4871) (LpA)

65.8 dB(A) ± 3 dB(A)

Machine sound pressure level (ISO 3744, ISO

4871) (LwA)

84 dB(A)

Vibration level at the operator’s arms (ISO 5349-1) < 2.5 m/s

2

Standard batteries (2 x 12 V) 95 - 165 Ah @ 20 h

Battery compartment size (width x length x height) 350 x 350 x 300 mm

Vacuum system circuit capacity 1,055 mm H

2

O

10 SCRUBTEC 653B – 653BL – 651BCL – 661BL 9097058000(2)2009-10 A

ENGLISH USER MANUAL

Technical data for machines with brush/pad-holder deck

Model

SCRUBTEC 653B

(1 brush/pad-holder,

without drive system)

SCRUBTEC 653BL

(1 brush/pad-holder,

with drive system)

SCRUBTEC 661BL

(2 brushes/pad-

holders, with drive

system)

Cleaning width 530 mm 530 mm 610 mm

Squeegee width 760 mm 810 mm

Machine maximum length 1,323 mm 1,311 mm

Machine width without squeegee 541 mm 646 mm

Brush diameter 530 mm 305 mm

Weight without batteries and with empty tanks 87 kg 95 kg

Maximum weight with batteries and full tanks 234 kg 241 kg

Brush motor power 480 W 350 W

Brush speed 153 rpm 230 rpm

Brush/pad-holder pressure with extra-pressure function turned off 20 kg

Brush/pad-holder pressure with extra-pressure function turned on Optional 40 kg

Technical data for machines with cylindrical brush deck

Model

SCRUBTEC 651BCL

(2 cylindrical brushes, with drive system)

Cleaning width 510 mm

Squeegee width 760 mm

Machine maximum length 1,253 mm

Machine width without squeegee 575.5 mm

Cylindrical brush size (diameter x length) 110 x 485 mm

Weight without batteries and with empty tanks 105 kg

Maximum weight with batteries and full tanks 251 kg

Brush motor power 400 W

Cylindrical brush speed 570 rpm

Cylindrical brush pressure 26.5 kg

9097058000(2)2009-10 A SCRUBTEC 653B – 653BL – 651BCL – 661BL 11

USER MANUAL

ENGLISH

WIRING DIAGRAM (SCRUBTEC 653B)

Key

BAT 24 V battery

C1 Battery connector

C2 Battery charger connector

CH Battery charger (optional)

CS Deck connector

EB1 Function electronic board

ES1 Brush electromagnetic switches

ES2 Vacuum system relay

EV1 Water solenoid valve

F1 Deck fuse

F2 Vacuum system fuse

F4 Signal circuit fuse

F5 Brush release fuse

F6 Pump fuse

HM Hour counter (optional)

K1 Ignition key

M1 Brush/pad-holder motor

M2 Vacuum system motor

M5 Detergent pump (optional)

RV3 Detergent % potentiometer (optional)

SW1 Brush/drive system enabling switch

Colour codes

BK Black

BU Blue

BN Brown

GN Green

GY Grey

OG Orange

PK Pink

RD Red

VT Violet

WH White

YE Yellow

P100127

12 SCRUBTEC 653B – 653BL – 651BCL – 661BL 9097058000(2)2009-10 A

ENGLISH USER MANUAL

WIRING DIAGRAM (SCRUBTEC 653BL, SCRUBTEC 651BCL, SCRUBTEC 661BL)

(**)

(*)

P100128

Key

BAT 24 V battery

C1 Battery connector

C2 Battery charger connector

CH Battery charger (optional)

CSC Cylindrical brush deck sub-connector

EB1 Function electronic board

EB2 Drive system electronic board

ES1 Brush electromagnetic switches

ES2 Vacuum system relay

EV1 Detergent solenoid valve (optional)

F1 Deck fuse

F2 Vacuum system fuse

F3 Drive system fuse

F4 Signal circuit fuse

F5 Brush/pad-holder release fuse

F6 Pump fuse

HM Hour counter (optional)

K1 Ignition key

M1 Brush/pad-holder motor

M2 Vacuum system motor

M3 Drive system motor

M5 Detergent pump (optional)

RV2 Maximum speed potentiometer

RV3 Detergent % potentiometer (optional)

SW1 Brush/drive system enabling switch

SW2 Reverse gear switch

Only for machines with cylindrical brush deck(*)

Only for machines without on-board battery charger(**)

Colour codes

BK Black

BU Blue

BN Brown

GN Green

GY Grey

OG Orange

PK Pink

RD Red

VT Violet

WH White

YE Yellow

9097058000(2)2009-10 A SCRUBTEC 653B – 653BL – 651BCL – 661BL 13

USER MANUAL

ENGLISH

USE

WARNING!

On some points of the machine there are some adhesive plates indicating:

DANGER –

WARNING –

CAUTION –

CONSULTATION –

While reading this Manual, the operator must pay particular attention to the symbols shown on the plates.

Do not cover these plates for any reason and immediately replace them if damaged.

BATTERY CHECK/SETTING ON A NEW MACHINE

WARNING!

The electric components of the machine can be seriously damaged if the batteries are either improperly installed

or connected. The batteries must be installed by qualiﬁ ed personnel only. Set the function electronic board and

the battery charger (optional) according to the type of batteries used (WET or GEL).

Check the batteries for damage before installation.

Disconnect the battery connector and the battery charger plug.

Handle the batteries with great care.

Install the battery terminal protection caps supplied with the machine.

The machine requires two 12 V batteries, connected according to the diagram (57).

The machine can be supplied in one of the following modes:

Batteries (WET or GEL) already installed and ready to be usedA)

Check that the batteries are connected to the machine with the connector (12).1.

Insert the ignition key (80) and turn it to “I”.2.

If the green warning light (81a) turns on, the batteries are ready to be used.

If the yellow or red warning light (81b or 81c) turns on, the batteries must be charged (see the procedure in Maintenance

chapter).

Batteries (WET) installed on the machine, but without electrolyteB)

Open the cover (22) and check that the recovery tank (21) is empty, otherwise empty it with the drain hose (16).1.

Carefully lift the tank (40).2.

Remove the caps (53) of the batteries (52).3.

WARNING!

Pay attention when using sulphuric acid, as it is corrosive. If it comes in contact with skin or eyes, rinse

thoroughly with water and consult a physician.

Batteries have to be ﬁ lled in a well-ventilated area. Wear protective gloves.

Fill up the battery cells with sulphuric acid for batteries (density 1.27 to 1.29 kg at 25°C) in accordance with the instructions 4.

shown in the Battery Manual. The correct quantity of sulphuric acid is shown in the Battery Manual.

To avoid damaging the ﬂ oor, dry with a cloth both acid and water on the top of the batteries after charging.5.

Let the batteries rest and ﬁ ll in with sulphuric acid as shown in the Battery Manual.6.

Charge the batteries (see the procedure in Maintenance chapter).7.

Without batteriesC)

Buy appropriate batteries (see Technical Data paragraph).1.

For battery choice and installation, apply to qualiﬁ ed battery Retailers.2.

Set the machine and the battery charger (if equipped) according to the type of batteries installed (WET or GEL) as shown 3.

in the following paragraph.

14 SCRUBTEC 653B – 653BL – 651BCL – 661BL 9097058000(2)2009-10 A

ENGLISH USER MANUAL

BATTERY INSTALLATION AND BATTERY TYPE SETTING (WET OR GEL)

Set the electronic board of the machine and of the battery charger (if equipped) according to the type of batteries installed (WET or

GEL) according to the following procedure:

Machine setting

Turn the ignition key (80) to “I” and pay attention to the following in the very ﬁ rst seconds of machine operation:1.

If the green warning light (81a) is ﬂ ashing, the machine is set to GEL.•

If the red warning light (81c) is ﬂ ashing, the machine is set to WET.•

If the setting is to be changed, perform the following procedure.2.

Turn off the machine by turning the ignition key (80) to “0”.3.

Press and hold the switches (71) and (73) at the same time, then turn the ignition key (80) to “I”.4.

Release the switches (71) and (73) at least 8 seconds after starting the machine.5.

Within 3 seconds, press the switch (73) again for a few seconds and check that the warning light for the required setting is 6.

ﬂ ashing (as shown in step 1).

Battery charger setting (for machines with on-board battery charger)

Remove the battery charger data inspection window screws (A, Fig. 1).7.

Remove the window (B).8.

Turn the battery charger selector (C) to WET position for lead batteries, or to GEL position for gel batteries.9.

Install the window (B) and tighten the screws (A).10.

Battery installation

Open the cover (22) and check that the recovery tank (21) is empty, otherwise empty it with the drain hose (16).11.

Carefully lift the tank (40).12.

Install the batteries.13.

Battery charging

Charge the batteries (see the procedure in Maintenance chapter).14.

A

C

B

P100105

Figure 1

9097058000(2)2009-10 A SCRUBTEC 653B – 653BL – 651BCL – 661BL 15

USER MANUAL

ENGLISH

BEFORE MACHINE START-UP

Brush/pad-holder deck or cylindrical brush deck installation/removal

The machine can be equipped with either the brush/pad-holder deck (18a and 18b) or the cylindrical brush deck (18c).

For deck installation/removal see the procedure in Maintenance chapter.

NOTE

When the deck is installed/removed, it may be necessary to change the squeegee too, because they must have the

same width. For correct matching of deck and squeegee, see the Squeegee Installation paragraph.

Brush/pad-holder installation/removal

According to the kind of cleaning to be performed, the machine can be equipped either with brushes (A, Fig. 2) or pad-holders 1.

(B) with pads (C) together with the appropriate deck.

Insert the ignition key (80) and turn it to “I”.2.

If equipped, turn the speed adjuster (84) to idle by turning it counter-clockwise.3.

Place the brushes (A) or the pad-holders (B) under the appropriate deck (18a) or (18b).4.

Lower the deck on the brushes/pad-holders by pressing the pedal (11).5.

Turn the ignition key (80) to “I”.6.

Press the brush/pad-holder switch (71).7.

Press one of the switches (83) to engage the brush/pad-holder, then release it. If necessary, repeat the procedure until the 8.

brushes/pad-holders are engaged.

S311334

Figure 2

WARNING!

(Only for SCRUBTEC 653BL, SCRUBTEC 651BCL, SCRUBTEC 661BL): Turn the speed adjuster (84) counter-

clockwise to drive the machine at the minimum speed.

To engage the brush/pad-holder press the switch (83) which turns on the brush/pad-holder motor.

To remove the brushes/pad-holders, the deck must be lifted by pressing the pedal (11), then press the switch (75) and wait for 9.

the brush/pad-holder to fall on the ﬂ oor.

Turn the ignition key (80) to “0”.

16 SCRUBTEC 653B – 653BL – 651BCL – 661BL 9097058000(2)2009-10 A

ENGLISH USER MANUAL

Types of brushes available

305 mm-models 530 mm-models

PROLENE PROLENE

MIDLITE GRIT 180 MIDLITE GRIT 180

MIDGRIT 240 MIDGRIT 240

PROLITE PROLITE

UNION MIX UNION MIX

Brush/pad application guide (suggestions only)

Models MIDLITE GRIT 180 MIDGRIT 240 PROLENE PROLITE UNION MIX

General cleaning:

Concrete

Terrazzo ﬂ oor

Ceramic tiles/quarrystones

Marble

Vinyl tiles

Rubber tiles

Polishing:

Rubber tiles

Marble

Vinyl tiles

Cylindrical brush installation/removal (only for SCRUBTEC 651BCL)

Turn the ignition key (80) to “0”.1.

Lift the cylindrical brush deck by pressing the pedal (11).2.

Remove the handwheels (A, Fig. 3) and the lids (B) by pushing them downwards and pressing on the handwheels.3.

Install the cylindrical brushes (C).4.

The cylindrical brushes can be installed on either sides.

Install the lids (B) and fasten them with the handwheels (A).5.

To remove the cylindrical brushes, perform steps 1 to 5 in the reverse order.6.

A

B

C

D

E

A

C

B

S311318

Figure 3

9097058000(2)2009-10 A SCRUBTEC 653B – 653BL – 651BCL – 661BL 17

USER MANUAL

ENGLISH

Types of cylindrical brushes available

485 mm-models

POLYPROPYLENE 0.40

HARD NYLON 0.60

SOFT NYLON 0.45

Cylindrical brush application guide (suggestions only)

Models POLYPROPYLENE 0.40 HARD NYLON 0.60 SOFT NYLON 0.45

General cleaning:

Concrete

Terrazzo ﬂ oor

Ceramic tiles/quarrystones

Marble

Vinyl tiles

Rubber tiles

Squeegee installation

Install the squeegee (25) and fasten it with the handwheels (26), then connect the vacuum hose (15) to the squeegee.1.

Adjust the squeegee with the handwheel (27) so that the rear blade - in all its length - touches the ﬂ oor.2.

Guide to match squeegees and brush/pad-holder decks

Deck model Squeegee model

Deck with one brush (18a), brush diameter: 530 mm Aluminium (Fig. 7), width 760 mm

Deck with two brushes (18b), brush diameter: 305 mm Steel (Fig. 6), width 810 mm

Deck with two cylindrical brushes (18c), brush length: 485 mm Aluminium (Fig. 7), width 760 mm

Solution or washing water tank ﬁ lling

NOTE

If the machine is equipped with Chemical Mixing System (switch (77) (optional)) the tank must be ﬁ lled with clean water,

otherwise the tank must be ﬁ lled with solution.

Open the ﬁ ller neck (8).1.

(2. For machines without Chemical Mixing System)

Use the rear ﬁ ller neck (41) or the front ﬁ ller neck (37) to ﬁ ll the tank (20) with a solution suitable for the work to be performed.

Do not ﬁ ll the solution tank completely, leave a few centimetres from the edge. Use the removable hose (17) as reference.

Always follow the dilution instructions on the label of the chemical product used to prepare the solution.

The solution temperature must not exceed 40°C.

WARNING!

Use only low-foam and non-ﬂ ammable detergents, intended for automatic scrubber applications.

(For machines with Chemical Mixing System)

Fill the tank (20) with clean water by using the rear ﬁ ller neck (41) or the front ﬁ ller neck (37).

Do not ﬁ ll the clean water tank completely, leave a few centimetres from the edge.

The water temperature must not exceed 40°C.

18 SCRUBTEC 653B – 653BL – 651BCL – 661BL 9097058000(2)2009-10 A

ENGLISH USER MANUAL

Detergent tank ﬁ lling (For machines with Chemical Mixing System)

Open the cover (22) and check that the recovery tank (21) is empty, otherwise empty it with the drain hose (16).1.

Carefully lift the tank (40).2.

Open the plug (46).3.

Fill the tank (45) with a detergent suitable for the work to be performed (highly concentrated detergent).4.

Do not ﬁ ll the detergent tank completely, leave a few inches from the edge.

CAUTION!

Use only low-foam and non-ﬂ ammable detergents, intended for automatic scrubber applications.

NOTE

In case of new system, system emptied for cleaning, etc., wait for the hoses to ﬁ ll up, before starting the Chemical Mixing

System.

MACHINE START AND STOP

Starting the machine

Prepare the machine as shown in the previous paragraph.1.

Insert the ignition key (80) and turn it to “I”.2.

Check that the green warning light (81a) turns on (charged batteries).

If the yellow or red warning light (81b or 81c) turns on, turn the ignition key back to “0” and charge the batteries (see the

procedure in Maintenance chapter).

Drive the machine to the working place:3.

By pushing it with the hands on the handlebar (2) (only for SCRUBTEC 653B).•

By pushing it with the hands on the handlebar (2) and pressing the switch (83) to move forward, or pressing the switch (83) •

together with the switch (78) to move rearward (only for SCRUBTEC 653BL, SCRUBTEC 651BCL, SCRUBTEC 661BL).

The forward speed can be adjusted with the adjuster (84).

Lower the squeegee (25) with the lever (10).4.

Lower the brush/pad-holder deck by pressing the pedal (11).5.

Press the brush/pad-holder and vacuum system switch (71).6.

Press the washing water ﬂ ow control switches (82) as necessary, depending on the type of cleaning to be performed.7.

Start cleaning, by moving the machine as shown in step 3.8.

If necessary, adjust the maximum speed with the adjuster (84).

If it is necessary to use the vacuum system only, stop the brush/pad-holder and the vacuum system with the switch (71), and 9.

press the vacuum system switch (73).

NOTE

To move the machine forward, press either the left or right switch (83) or both.

Stopping the machine

Stop the machine with the handlebar (2) (only for SCRUBTEC 653B).10.

Stop the machine by releasing the switches (83) (only for SCRUBTEC 653BL, SCRUBTEC 651BCL, SCRUBTEC 661BL).

Turn off the brushes and the vacuum system by pressing the switches (71 and 73).11.

Lift the brush/pad-holder deck by pressing the pedal (11).12.

Lift the squeegee (25) with the lever (10).13.

Make sure that the machine cannot move independently.14.

9097058000(2)2009-10 A SCRUBTEC 653B – 653BL – 651BCL – 661BL 19

USER MANUAL

ENGLISH

MACHINE OPERATION (SCRUBBING/DRYING)

Start the machine as shown in the previous paragraph.1.

If necessary, press the washing water ﬂ ow control switches (82) as necessary, depending on the type of cleaning to be 2.

performed.

If necessary, stop the machine and turn the squeegee adjusting handwheel (27) so that the rear blade - in all its length - 3.

touches the ﬂ oor.

If necessary, stop the machine and turn the adjusting handwheel (28); when turning it clockwise or counter-clockwise the 4.

machine forward speed can be adjusted.

If necessary, stop the machine and turn the machine forward speed adjusting handwheel (29) (only for SCRUBTEC 653B) as 5.

shown below:

Turn it counter-clockwise to increase the forward speed;•

Turn it clockwise to decrease the forward speed.•

NOTE

For correct scrubbing/drying of ﬂ oors at the sides of the walls, Nilﬁ sk Alto suggests to go near the walls with the right side

of the machine as shown in ﬁ gure 4.

A

B

P100106A

Figure 4

CAUTION!

To avoid any damage to the ﬂ oor surface, turn off the brushes/pad-holders when the machine stops in one

place, especially when the extra pressure function is on.

Page is loading ...

Nilfisk-ALTO SCRUBTEC 653 User manual

Nilfisk-ALTO SCRUBTEC 653 User manual

in other languages

Related papers

Other documents