Graco Trabon MSP Zero-Leak Inlet Shut-off Valve User manual
- Type
- User manual
DESCRIPTION
The MSP Zero-Leak inlet shut-off valve is designed for use in oil
only header lines, for the lubrication of extended systems and/or
systems with varied lube frequencies. Such applications include
automotive transfer lines, conveyor lines, flexible machining
centers and also complete plant lubrication.
The MSP Zero-Leak inlet shut-off valve can be mounted as the
inlet section to any primary (master) divider valve assembly. By
using a remote manifold kit, it can be teed off of the header line
to a remote primary (master) divider valve assembly.
The MSP Zero-Leak shut-off valve is supplied normally closed to
flow. When the coil is energized, the zero-leak valve is opened,
allowing oil to flow through. Once the proper amount of oil has
been dispensed, the valve is de-energized, shutting off oil flow.
The Zero-Leak valve is designed for header-line pressures up to
1500 psi.
FEATURES/BENEFITS
Designed for use with an oil header line system, which is •
an economical method of providing lubricant to extensive
systems. Reduces plumbing and installation cost.
When used in a header line system, lubrication zones are •
easily extended or deleted as changes are made to the lube
circuit. This reduces engineering design costs.
Enables individual zone lubrication. Prevents over •
lubrication thus saving on lubrication costs.
Facilitates individual zone operation and monitoring. •
Identifies a fault in a specific zone for ease of
troubleshooting. Helps lessen machine downtime, which
means more production time.
Solenoid can be rotated through1800 to accommodate •
any electrical hook up --orientation. Allows for faster
installation to reduce costs.
Available with three pin mini-connection as standard•
Available with NPSF pipe, BSPP or SAE, o-ring sealed ports. •
Inlet restrictor/filter available for use in continuous •
pressurized header line systems. This will slow down lube
inrush and enable accurate control of the lube systems.
Order Part Number 563074 (463-410-204) for NPT pipe
inlet.
Coil is molded and sealed, making it impervious to coolant. •
Allows mounting of valve in harsh environments.
OPERATION
The MSP Zero-Leak inlet shut-off valve is used in conjunction
with an oil header line lube system with each shut-off valve
representing a zone of lubrication (See Fig.1). The header line
can either be continuously (use restrictor) or intermittently
pressurized upon demand. When the particular machine zone
requires lubrication, based upon a pre-determined interval, an
electrical signal from a Trabon Flexi-Monitor
®
or machine PLC
will sequentially energize the solenoids attached to the shut-
off valves (A1), (A2), and (A3). This will open the valve and
allow lubricant from the header line to cycle the divider valve,
thus providing lubricant to the points within the zone. Once the
zone has received the proper amount of lubrication, determined
through monitoring the cycle switch (B) or proximity switch (B)
for appropriate number of cycles, the controller will de-energize
the solenoid and the valve will shut-off lubricant flow.
(B)
PUMP AND
RESERVOIR
FIGURE 1
(B)
SECONDARY DIVIDERS
MASTER
DIVIDER
) (
) (
) (
(A2)
(A3)
(B)
(A1)
HEADER LINE
Trabon
®
MSP Zero-Leak
Inlet Shut-off Valve
All written and visual data contained in this document are based on the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
©2007-2009 Graco Inc. Form No. L10104 Rev. B 1/09 Printed in U.S.A. All other brand names or marks are used for identification purposes and are trademarks of their respective owners. All written and
visual data contained in this document are based on the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
Contact us today!
To receive product information or talk with a Graco representative,
call 800-533-9655 or visit us online at www.graco.com.
WIRING DIAGRAM
NOTE: Diode on DC
version only
Graco endorses the SAE recommendation of ISO 18/14 (ISO 4406) oil cleanliness for most bearing
applications. Some high speed bearing may require cleaner oil. Consult the bearing manufacturer for
recommendation.
COMPONENT ORDERING
Description Part No. Old Part No.
Zero-Leak valve, 120 VAC w/
Brad Harrison 3 pin connector
(1/4-18 NPSF) 563460 527-004-320
(9/16-18 SAE) 563468 527-005-200
Zero-Leak valve, 24 VDC w/Brad
Harrison 3 pin connector
(1/4-18 NPSF) 563464 527-004-870
(9/16-18 SAE) 563467 527-005-180
Zero-Leak valve (no coil), 1/4 BSPP 563462 527-004-770
Repair Kit (w/wrench nut) 563933 560-002-640
COMPONENT ORDERING (continued)
Replacement Coil, 120 VAC 557226 492-120-206
Replacenment Coil, 24 VDC 557225 492-120-205
Remote mount manifold kit (includes outlet
manifold, O-Ring & 2 Mtg screws)
(1/4-18 NPSF) 563461 527-004-360
Inlet Restrictor w/90 Micron Last Chance Filter
(1/4 NPTF) 563074 463-410-204
Brad Harrison Mating Cables
6ft (1.3m) (3 pin) straight 558021 570-999-080
12ft (3.7m) (3 pin) straight 558022 570-999-090
Note: See bulletin L10105 for Modular Zero-Leak
SPECIFICATION
Position Normally closed
Material Anodized Aluminum body
Pressure (max) 1500 psi (104 bar)
Lubricant Oil up to 5000 SUS
Electrical Rating:
(AC) 120V at 60 Hz, 9.5W continuous duty coil,
class "H" insulation, .220 amps holding
(DC) 24V, 28W continuous duty coil w/
diode, class "H" insulation
Filtration (ISO 18/14) or better oil cleanliness level
-
1
-
2
Graco Trabon MSP Zero-Leak Inlet Shut-off Valve User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Graco Trabon MSP Modular Zero-Leak Valve & MSP Modular Filter User manual
-
-
-
-
-
-
-
-
-
