Costar CDC3128VTIR Owner's manual

Costar
Brand
Costar
Model
CDC3128VTIR
Category
Security cameras
Type
Owner's manual
Eye Ball type Camera (osd controller in the case)
Owner’s Manual
Caution / Feature / Warning Page 03-05
Main Part
Installation
Drawing
Page 07-08
Page 09-10
Page 12-12
OSD Guide Page 13-30
Specification Page 30-31
CDC3611IRVA
1
Caution
Features
Warning
Components
Main Parts
Drawing
Installation
Connection
3
4
5
6
7
9
11
12
2
Contents
Camera Operation
Menu
Setting
EXPOSURE
LENS
SENSE_UP
AGC
BACKLIGHT
RGB
WB MODE
3D_DNR
RED GAIN
BLUE GAIN
DAY&NIGHT
NIGHT C
D&N MODE
NIGHT A
FUNCTION
MIRROR
SHARPNESS
COLOR MODE
DPC
GAMMA
TITLE
Specification
Camera power consumption
OSD COLOR
COMMUNICATION
FACTORY SET
SLC
NIGHT UP
MOTION
PRIVACY
SET
MONITOR
LANGUAGE
13
13
14
15
15
17
19
19
20
20
20
21
21
21
22
22
23
23
23
23
24
24
24
25
25
27
27
27
28
28
28
29
29
29
30
31
3
We thank you very much for taking our camera.
First of all, please read this instruction manual carefully before use in
order to avoid any mistake and to use your camera with right manner.
INFORMATION-
WARNING-
WARNING-
This equipment has been tested and found to comply with limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
To prevent electric shock and risk of fire hazards:
1) Do NOT use power sources other than that specified.
2) Do NOT expose this appliance to rain or moisture.
The lightning flash with an arrowhead symbol, within an
equilateral triangle is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product's
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
To reduce the risk of electric shock,
Do not remove cover ( or Back),
No user serviceable parts inside.
Refer servicing to qualified service personnel.
This installation should be make by a qualified service person and
should conform to all local codes.
4
Super Natural High Resolution
Digital Wide Dynamic Range (D-WDR)
Excellent Sensitivity
Smart 3D-DNR
Smart BLC
True Day & Night
Using a 410,000 pixel Sony Super HAD II
CCD produces clear image with a horizontal
resolution of 620TV Lines for Color and
670TV Lines for B/W. You'll get a more vivid
and clearer natural color image.
Digital Wide Dynamic Range technology
helps to capture perfect images in both bright
and dark environments simultaneously.
Without using Sony Double Scan CCD, the
true WDR performance is displayed.
Adopting a Diagonal 6mm (1/3"), highly
sensitive CCD and digital signal processing
technology, it can clearly distinguish the
outline and color of a subject in an extremely
low luminance environment – even.
The DNR function is the technology to
eliminate noise for providing a distinct and
clear image. The 2D filter reducing noise in
the brightness of image and 3D Filter reducing
noise caused by movement. When movement
appears, Smart DNR works to adjust lagging,
and it is automatically comes back ON if there
is no more movement at a scene.
Conventional cameras always have fixed
BLC zones. BLC-SMART means that the
camera automatically changes the BLC zone
in various conditions.
Masks overly exposed light to produce a true
video image of any environment.
Digital Slow Shutter technology is the primary
technology we offered for the better images at night.
(Up to x 1024)
The sub monitor function enables easy
adjustment of the camera angle within the
monitoring range during its installation.
Compensates the area that is saturated due to
bright light.
Masks overly exposed light to produce a true video
image of any environment.
The camera control is convenient by using
different foreign language O.S.D. Also the
camera can be controlled by selecting text
displayed on the monitor screen.
SYNC(INT/LL), SENS-UP, FREEZE,
FLIP(H/V-REV), D-ZOOM, SHARPNESS,
MOTION DETECTION and PRIVACY
Communication(RS485) functions
are provided.
Digital Slow Shutter (SENSE-UP)
Sub Monitor Function
Smart IR LED
High Light Masking (HME)
OSD
Additional Functions
Features
5
6
1) Do not install the camera in extreme temperature condition.
Only use the camera under conditions where temperatures are between
-10 C and +50 C (if heater have it can operate at : -45 C and +50 C)
Be especially careful to provide ventilation when operating under high temperatures.
ºº ºº
2) Do not install or use the camera in a environment where the
humidity is high.
It can cause the image quality to be poor.
3) Do not install or use the camera under unstable lighting conditions.
Severe lighting change or flicker can cause the camera to work improperly.
4) Do not touch the front lens of the camera.
This is one of the most important parts of the camera. Be careful not to leave fingerprints
on the lens cover.
5) Do not drop the camera or protect it from physical shocks.
It can cause malfunctions to occur.
6) Never keep the camera pointed directly at strong light.
It can damage the CCD.
7) Do not expose the camera to radioactivity.
If exposed to radioactivity the CCD will fail.
8) The camera requires periodic inspection.
9) Stop using your camera when you find it malfunctioning.
10) Do not Install the camera on a surface that can not support it.
11) Do not hold plug with wet hands.
12) Do not dis-assemble the camera.
13) Do not use the camera close to a gas or oil leak.
Contact an authorised technician to carry out the inspection.
If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.
If the camera is installed on an inappropriate surface, it may fall
and cause injury.
It could cause an electric shock.
It may result in an electric shock or other hazards.
It may result in a fire or other hazards.
Warning
1) CameraDome
2) Cable for Extra Video
4) Manual
3) Screw for Installation
Components
5) Mounting Template
2) Focus-Driver / L-wrench
Main Part
1) Upper Ball and Down Ball
The ball can be adjust by 3 Axis , it can easy be install to anyplace. Like wall or ceiling.
Also you can adjust the focus and zoom on the upper ball part by the focus-driver .
2) OSD Board
We use the joystick osd board for e
asily
controlled by OSD menu.
}
}
SET :
Left / Right and UP / Down :
3) TDN Lens (True Day & Night )
5) Cover
6) Base
7) AC24V/DC12V Dual Power Board
This button can be
used to confirm settings after changing the value
of the selected function or current conditions.
left and Right : Used when changing item
values, by moving the cursor to the left or right
on the menu screen. Up and Down : Used for
selecting items by moving the cursor up and
down on the menu screen.
Normal used 2.8~12mm varifocal DC Auto Iris TDN Lens.
By the model name we supply 2 type ir led
board. One is 42 ir led board , the others is 24 ir
led Board with 4heaters. Of course , if you select
the camera without ir, It means this part no have.
Dual power sported board .
12V DC input it is ok. and 24V AC also ok.
4) IR LED Board
After finished Adjust, we need fix the ball by using the cover.
When you plan to install the camera, please fix this base first.
When you select the ac type camera, built in the
Press the joystick button , the
MAIN MENU appears.
Focus adjustable Zoom adjustable
Extra Video Connector
OSD Board
42 IR Led Board
24 IR Led Heater Board
7
8
9
10
Installation
1) Make the hole
2) Fixed the base
3) Fixed the ball
4) Fixed the ball
5) Fixed the screw
1. Make the screw hole and cable hole by the mounting template.
2. Fix the Base Housing to the desired place with screws
supplied.
3. Power Connect & Monitor Impedance.
Made sure which power supply that you selected before you use.
- DC12V regulated power supply (DC12V camera only),Make Sure "+" / "-" .
Dual power supply (AC24V/DC12V both can be used)
- To avoid fire or shock hazard, must use a UL listed power supply.
- Set the monitor impedance switch to 75½. Check the impedance switch when
the screen turns blurred.
4. Fix the ball by using the cover, and then adjust desired scene by turning and
moving the ball,
5. Focus and Functions Adjust
- Open the osd - cover , and connect the power , and use the extra cable to adjust
the focus and others functions . After finished, please tighten the osd - cover carefully.
Note :
1) Before you fix the osd-cover, please make sure the rubber on the osd-cover part
fixed very well.
2) Before power connect, please make sure which power-type camera you buy, and
select the right adaptor to supply the power.
stopper Ring by turning it with hands. after it you can fix the screw
with the L wrench.
Installation Step
BNC : Video-out
Terminal jack : Power-in
OSD - Cover
To test-monitor
OSD controller
Adjust the
focus level
Adjust the
zoom level
Installation
- As the connecting method varies with the instruments, refer to the manual
supplied with the instrument.
- If necessary, you can connect the monitor to the REMOTE jack on the back of
your camera.
- Only connect the cable when the power is turned off.
- Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate
device.
1) Connection to Monitor and Power
2) Connection to Power
Connect the adaptor to the power input connector as shown in the figure below.
The Standard voltage for camera operation :
AC : DC 12V ± 10%, AC 24V±10% ;
DC : DC 12V ± 10%
Note
Before connect the power jack , please really have a check the power supply.
Connection
VIDEO
1) BNC : Video output
2) Power Jack
Adaptor
Power Jack
24VAC/12VDC input
Power Jack
12VDC input only
VIDEO
VIDEO
Hi-Z
75Ω
IN
OUT
VIDEO
Hi-Z
75Ω
IN
OUT
AC (Dual type) camera series
DC camera series
Drawing (mm)
Option Bracket (F13C80)
11
12
■
■
1. EXPOSURE 2. RGB
3. DAY&NIGHT
LENS WB MODE D&N MODE
BACKLIGHT RED GAIN NIGHT C
AGC BLUE GAIN NIGHT A
SENSE_UP COLOR MODE 6. PRIVACY
6. PRIVACY
3D_DNR 5. MOTION5. MOTION MASK 1
AREA SET MASK 2
4. FUNCTION SENSITI MASK 3
MIRROR SHOW INDI MASK 4
SHARPNESS EXTER OUT MASK 5
GAMMA MASK 6
SLC MASK 7
NIGHT UP MASK 8
7. SET 8. EXIT
TITLE SAVE & EXIT
DPC EXIT
MONITOR
LANGUAGE
OSD COLOR
COMMUNICA
FACTORY SET
■
Camera Operation
■
Camera Operation
Menu
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
LENS
BACKL I GHT OFF
AGC OFF
SENSE-UP X4
3D DNR SMART
MANUAL
EX I T JUMP
Setting
Settings can be made by using the OSD controller that fixed on the
camera. If joystick osd use , please press it for start the osd menu
setting, and if we use the 5buttons osd board, and then please press
the Set button.
Extra Video Connector
Joystick Switch
MANUAL:
Select when fixed lens is used
13
14
■
■
Camera Operation
EXPOSURE
EXPOSURE Selected
EXPOSURE by using the Left/Right,Up/Down buttons so that
the arrow indicates EXPOSURE.
1) Lens
LENS MANUAL
ELC LEVEL
0
2
7
E. SHUTTER AUTO
RETURN
FOCUS
TA
R
GET
[
0000
]
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
LENS
BACKL I GHT OFF
AGC OFF
SENSE-UP X4
3D DNR SMART
MANUAL
EX I T JUMP
On the Lens menu you
can use DC or VIDEO or
MANUAL Lens. When
you set DC, a submenu
appears where you can set
the brightness of the picture.
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
LENS
BACKL I GHT OFF
AGC OFF
SENSE-UP X4
3D DNR SMART
DC
EX I T JUMP
LENS
D
C
DC LEVEL 0
2
7
E. SHUTTER DC–AUTO
RETURN
FOCUS
TA
R
GET
[
0000
]
b) DC/VIDEO : Auto Iris Lens selection
> The DC LEVEL & Shutter level can be adjustment.
a) MANUAL :
Manual Lens selection.
> The ELC LEVEL & Shutter
level can be adjustment.
■
Camera Operation
15
16
■
■
Camera Operation
EXPOSURE
EXPOSURE >BLC
EXPOSURE by using the Left/Right,Up/Down buttons so that
the arrow indicates EXPOSURE.
2) BLC (BACK LIGHT COMPENSATION)
When there is a strong backlight behind the object, clear images of the
background as well as the object can still be obtained by using the
BACKLIGHT function. This function is to deliver a distinctive subject and
background at the same time, even when t he subject is in backlight, unlike
conventioned cameras.
BLC : Enables a user to directly
select a desired area from a
picture, and to view the area more
clearly.
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
LENS
BACK LIGHT OFF
AGC OFF
SENSE-UP X4
3D DNR SMART
MANUAL
EX I T JUMP
BACK LIGHT- BLC
BLC MODE SMART
SET LEVEL M
I
D
RETURN
BAC
K
LIG
H
T
- HME
HME BLC SET
MASK1 ON
MASK2 ON
MASK3 ON
MASK4 ON
MODE ALL DAY
RETURN
BACK LIGHT- D. WDR
SET LEVEL 0 1 0
RETURN
SET LEVEL 0 5 0
BLC ON
BLC OFF
- BLC MODE : MANUAL & SMART MODE
► SMART : Conventional cameras always have fixed BLC zones.
BLC-SMART means that the camera automatically changes
the BLC zone in various conditions.
► HME : Masks overly exposed light to produce a true video image
of any environment.
► D-WDR : By D-WDR image processing techniques of input image,
information of input image
brightness value is
analyzed, that part of
relatively bright and dark
images is judged and
through different
Brightness value mapping
will have the effect of
improving the contrast
ratio.
■
Camera Operation
17
18
■
■
Camera Operation
EXPOSURE
EXPOSURE >AGC
EXPOSURE by using the Left/Right,Up/Down buttons so that
the arrow indicates EXPOSURE.
3) AGC (AUTO GAIN CONTROL)
The higher the gain level, the brighter the screen, but the higher the noise.
- HIGHEST : 6dB ~ 52dB.
- HIGH : 6dB ~ 42dB.
- MIDDLE : 6dB ~ 30dB.
- LOW : 6dB ~ 18dB.
- OFF : The gain is fixed at 6dB.
4) SENS-UP (X2~X1024)
When it is night or dark, the camera
automatically detects the light level and
maintains a clear picture if this mode is
activated.
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
LENS
BACK LIGHT OFF
AGC OFF
SENSE-UP X4
3D DNR SMART
MANUAL
EX I T JUMP
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
LENS
BACK LIGHT OFF
AGC OFF
SENSE-UP X4
3D DNR SMART
MANUAL
EX I T JUMP
5) 3D-DNR (3D Filter reducing noise caused by movement.)
Newly developed 3D filtering enhances Digital Noise Reduction at
low light levels.
► SMART 3D-DNR : With special
technology, it produces less noise
but more color at night. there is no
image lagging. When movement
appears, Smart DNR works to
adjust lagging, and it is
automatically comes back ON if
there is no more movement at a
scene.
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
LENS
BACK LIGHT OFF
AGC OFF
SENSE-UP X4
3D DNR SMART
MANUAL
EX I T JUMP
*** 3D_DNR OFF/LOW/MID/HIGH/SMART
SETTING (Adjust NOISE when low
light condition)
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
WB MODE
RED GAIN 128
BLUE GAIN
COLOR MODE
EXIT JUMP
AWC
128
NORMAL
COLOR
Select AWC/ATW/MANUAL/PUSH
LOCK (adjust white balance)
■
COLOR
1) WB MODE (WHITE BAL. MODE)
Please select the WHITE BALANCE
function by the condition where you
will install.
►ATW (Auto Tracking White Balance)
The color temperature is monitored
continuously and thereby white balance
is automatically set.
►AWC (Auto White Balance Control)
To find the optimal luminance level for
the current environment, point the camera
towards a sheet of white paper and press
the Function Setup switch. If the
environment changes, readjust it.
►PUSH LOCK
This mode only adjust the white balance.
■
Camera Operation
19
20
■
Camera Operation
2) RED GAIN ( Adjust RED Gain )
If the color so so on the monitor, we can increase/ decrease the red and blue color
values and monitor the color changes of the object.
Pictures can be displayed in either color or black and white.
■
DAY & NIGHT
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
WB MODE
RED GAIN 128
BLUE GAIN
COLOR MODE
EXIT JUMP
AWC
128
NORMAL
COLOR
RED GAIN SETTING
(Adjust RED gain)
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
WB MODE
RED GAIN 128
BLUE GAIN
COLOR MODE
EXIT JUMP
AWC
128
NORMAL
COLOR
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
WB MODE
RED GAIN 128
BLUE GAIN
COLOR MODE
EXIT JUMP
AWC
128
NORMAL
COLOR
RED /BLUE GAIN SETTING
(Adjust RED/ BLUE gain)
White balance adjustment
NORMAL / COOL / WARM
3) BLUE GAIN ( Adjust BLUE Gain )
we can increase/ decrease the blue color
values and monitor the color changes of
the object.
4) COLOR MODE
White balance adjustment, there have
NORMAL / COOL / WARM selectable
by the outside environment.
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
D&N MODE
NIGHT C. 050
NIGHT A.
AUTO
EXIT JUMP
050
Select AUTO/COLOR/BW
(TDN FUNCTION/COLOR/
BLACK AND WHITE)
DAY & NIGHT
1)D&NMODE
Please the right mode that your camera use.
- AUTO:
- COLOR:
-B/W:
The camera automatically switches
between day and night.
The camera stays in day mode.
The camera stays in night mode.
►
(Only removing burst signal)
- COLOR -> BW SWITCHING TIME SETTING
- BW -> COLOR SWITCHING TIME SETTING
- SMART IR function ON/OFF
- READ TIME SETTING
(Adjust filter switching time)
- EX-IR external connecting mode : EXT
- BURST ON/OFF SETTING
AUTO: The camera automatically
switches between day and night.
BURST
028
B&W->COLOR
SMART IR
READ TIME
EX–IR INT.
RETURN
ON
D & N- AUTO
COLOR-> B&W
012
ON
003
AUTO
■
Camera Operation
21
22
■
Camera Operation
2) NIGHT C. (NIGHT COLOR )
We can change the value of night color suppress setting that you wish.
2) SHARPNESS
Please more carefully use this Function for your camera adjust.
And don't increase the SHARPNESS lever too high, the picture may
become distorted or noise may appear.
■
DAY & NIGHT
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
D&N MODE
NIGHT C. 050
NIGHT A.
AUTO
EXIT JUMP
050
DAY & NIGHT
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
D&N MODE
NIGHT C. 050
NIGHT A.
AUTO
EXIT JUMP
050
DAY & NIGHT
APERTURE
SUPPRESS SETTING
COLOR
SUPPRESS SETTING
3) NIGHT A. (NIGHT APERTURE )
We can change the value of night aperture suppress setting that you wish.
■
Function
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
MIRROR
SHARPNESS
015
GAMMA
SLC
NIGHT-UP
OFF
EXIT JUMP
0.45
FUNCTION
OFF
OFF
OFF/MIRROR
SELECTABLE
1) MIRROR
If you select MIRROR model to ON,
the picture will be mirror.
MIRROR OFF MIRROR ON
3) GAMMA
Select the GAMMA value of 0.45 / 0.6 / 1.0 / MANUAL .
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
MIRROR
SHARPNESS
015
GAMMA
SLC
NIGHT-UP
OFF
EXIT JUMP
0.45
FUNCTION
OFF
OFF
ADJUST SHARPNESS
(Image sharpness can be adjusted)
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
MIRROR
SHARPNESS
015
GAMMA
SLC
NIGHT-UP
OFF
EXIT JUMP
0.45
FUNCTION
OFF
OFF
SELECT 0.45/0.6/1.0/MANUAL
(Adjust gamma level)
4) SLC (Side Light Compensation)
This function can make brighter image of corner of screen.
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
MIRROR
SHARPNESS
015
GAMMA
SLC
NIGHT-UP
OFF
EXIT JUMP
0.45
FUNCTION
OFF
OFF
Side Light Compensation
(Make brighter image of
corner of screen)
SET LEVEL
015
SLC
RETURN
SLC LEVEL SETTING
(corner of screen can be
adjusted)
■
Camera Operation
23
24
AREA1 SET
OFF
MOTION–AREA
RETURN
AREA2 SET
AREA3 SET
AREA4 SET
OFF
OFF
OFF
■
Camera Operation
5) NIGHT - UP
This function is very sensitivity adjustment
by SET UP. It increases the brightness
at the low light condition by raising the
set-up level.
2) SENSITIVE (SENSITIVITY LEVEL SETTING)
Please adjust sensitivity when using motion detection. As the sensitivity level
increases, even the smaller movements are detected.
3) SHOW INDI SETTING
Motion defected indicator can be selected as OFF / ICON / trace
4) EXTER OUT (Motion external signal output)
This function can make the motion pin height or low signal output.
DELAY TIME : After sensitive , the alarm signal display on the screen is delayed
from 1sec to 15sec.
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
MIRROR
SHARPNESS
015
GAMMA
SLC
NIGHT-UP
OFF
EXIT JUMP
0.45
FUNCTION
OFF
OFF
Sensitivity adjustment
by SET UP
■
MONTION
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
AREA SET
SENSITIV. 020
SHOW INDI.
EXTER OUT
EXIT JUMP
ICON
ON
MOTION
The motion detector detects the moving objects in the scene by monitoring
changes in brightness level.
MTOTION
First MOTION area ON / OFF
TOP
MOTION–AREA1
RETURN
BOTTOM
LEFT
RIGHT
020
055
030
080
Set first MOTION area
MOTION area selection
1) AREA SET
Select the motion area that you wish to observe
from the 4 areas in AREA SET mode.
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
AREA SET
SENSITIV. 020
SHOW INDI.
EXTER OUT
EXIT JUMP
ICON
ON
MOTION
SENSITIVITY LEVEL
SETTING
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
AREA SET
SENSITIV. 020
SHOW INDI.
EXTER OUT
EXIT JUMP
ICON
ON
MOTION
SHOW INDI SETTING
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
AREA SET
SENSITIV. 020
SHOW INDI.
EXTER OUT
EXIT JUMP
ICON
ON
MOTION
MOTION External
output ON / OFF
DELAY TIME
003
MOTION–EXTER OUT
RETURN
DELAY OUT SETTING
(Alarm signal display on the screen
is delayed from 1sec to 15sec)
■
Camera Operation
25
26
■
Camera Operation
NOTE : If the cursor is moved to CLR and the SET button pressed, all letters
are deleted. To edit a letter, change the cursor to the bottom left arrow and press
the SET button. Move the cursor over the letter to be edited, move the cursor to
the letter to be inserted and then press the SET button.
■
PRIVACY
: Hide an area so that it is not displayed on the monitor.
- MASK1~MASK8 : Up to 8 areas are selectable.
- Please select ON mode for the chosen area.
- Please adjust the size of the area to be observed by using the LEFT / RIGHT,
WIDTH, TOP / BOTTOM, HEIGHT button.
- COLOR : Determine area color.
- RETURN: Select this to save the PRIVACY menu settings and return to the
PRIVACY menu.
PRIVACY
EXPO
MOTI
RGB
PRIY
EXITFUNCD&N
SET
MASK1
MASK2
MASK3
MASK4
MASK5
OFF
EXIT JUMP
PRIVACY
MASK6
MASK7
MASK8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
L-TOP
PRIVACY–MASK1
GRAY
MODIFY
POSITION
COLOR SET
RETURN
START POINT
Able to set shape position
Able to set in different shapes
Able to set in different area
Mask color setting
(Can change the color of hidden part)
SELECT MASK1~8 (Set from 1 to 8
where wish to be hidden )
■
SETUP
1) CAM TITLE : If a title is entered, the title appears on the monitor.
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
TITLE
DPC SET
MONITOR
LANGUAGE
OSD COLOR
ON
EXIT JUMP
SETUP
COMMUNICA.
FACTORY SET
OFF
MODE 1
ENGLISH
BLUE
ON
NO
TITLE ON/OFF
SETTING
ABCDEFGHIJKLMNOPQRS
TUVWXYZ0123456789! #$%
&’( )*+,-./:;<=>?@[\]^_
USER TITLE
CLR POS RET
Set TITLE
(Select desired
characters and area)
2) DPC (Dead Pixel Compensation)
- DPC AUTO/OFF SETTING : Dead pixels are automatically removed.
- WHITE THR. : Cancelling White defective pixels.
- BLACK THR. : Cancelling Black defective pixels.
- DPC LEVEL GAIN LEVEL SETTING : Overall level can be adjusted.
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
TITLE
DPC SET
MONITOR
LANGUAGE
OSD COLOR
ON
EXIT JUMP
SETUP
COMMUNICA.
FACTORY SET
OFF
MODE 1
ENGLISH
BLUE
ON
NO
DPC AUTO/OFF SETTING
DPC-AUTO
WHITE THR.
BLACK THR.
DPC LEVEL
RETURN
150
030
030
3) Monitor :
Language :
The settings value of video appropriate to your monitor.
Select a preferred language among the supported languages.4)
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
TITLE
DPC SET
MONITOR
LANGUAGE
OSD COLOR
ON
EXIT JUMP
SETUP
COMMUNICA.
FACTORY SET
OFF
MODE 1
ENGLISH
BLUE
ON
NO
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
TITLE
DPC SET
MONITOR
LANGUAGE
OSD COLOR
ON
EXIT JUMP
SETUP
COMMUNICA.
FACTORY SET
OFF
MODE 1
ENGLISH
BLUE
ON
NO
MONITOR SETTING MODE
(MODE1/MODE2 Selectable)
Select Language
■
Camera Operation
27
28
Camera Operation
5) OSD COLOR :
You can change the letter color of OSD.
1) SAVE & EXIT :
:
Exit the osd menu after saving current setting.
Exit the osd menu without saving the current setting.4) EXIT
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
TITLE
DPC SET
MONITOR
LANGUAGE
OSD COLOR
ON
EXIT JUMP
SETUP
COMMUNICA.
FACTORY SET
OFF
MODE 1
ENGLISH
BLUE
ON
NO
OSD color adjustment
6) Communication : You can control the camera menu by RS485 and please
set PELCO-D and baud rate for your communication.
MOT
I
PRIY
EXITFUNCD&N
SET
MONITOR
LANGUAGE
OSD COLOR
ON
EXIT JUMP
COMMUNICA.
FACTORY SET
OFF
MODE 1
ENGLISH
BLUE
ON
NO
SETUP-COMMUNI.
PROTOCOL
CAMERA ID
BAUDRATE
RETURN
PELCO-D
001
9600BPS
Communication ON/OFF
Set to
Communication ID, Speed
Go back to factory default.
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
TITLE
DPC SET
MONITOR
LANGUAGE
OSD COLOR
ON
EXIT JUMP
SETUP
COMMUNICA.
FACTORY SET
OFF
MODE 1
ENGLISH
BLUE
ON
NO
7) FACTORY SET :
The camera setting will go back to factory
default.
■
EXIT
Exit OSD menu after
saving current setting.
EXPO
MOT
I
RGB
PRIY
EXITFUNCD&N
SET
SAVE & EXIT
EXIT
EXIT
EXPO
MOT
I
RGB
PRIY
FUNCD&N
SAVE & EXIT
EXIT
EXIT
Exit OSD menu.
Camera Operation
■
EXPO
RGB
TITLE
DPC SET
SETUP
EXIT
SET
■
Camera Power Consumption
■
29
30
Power Consumption Power input 42IR LED TYPE
24IR LED TYPE
WITH 4HEATER
WITH IR LED TYPE
AC (Min.) AC24V / DC12V 130mA / 180mA 130mA / 180mA 130mA / 180mA
AC (Max.) AC24V / DC12V 330mA / 470mA 391mA / 560mA -
DC (Min.) DC12V 120mA 120mA 120mA
DC (Max.) DC12V 350mA 420mA -
-10 C to + 50 C,
Under 90% (Non-
condensing)
-45 C to + 50 C,
Under 90% (Non-
condensing)
-10 C to + 50 C,
Under 90% (Non-
condensing)
Operating Temp. / Hum.
TYPE NTSC PAL
Image Sensor
1/3 SONY Super HAD Ⅱ COLOR CCD
Effective Pixels 768(H) x 494(V) 752(H) x 582(V),
Scanning System 525 Lines 2:1 Interlace 625 Lines 2:1 Interlace
Scanning requency(V) 59.94Hz 50Hz
Resolution (Color) 620 TV Lines
Resolution (B/W) 670 TV Lines
Illumination
Color 0.1 Lux, B/W 0.01Lux at F1.2 , IR LEDS ON : 0Lux
Shutter Speed 1/60 ~ 1/100,000 sec. 1/50 ~ 1/100,000 sec.
S/N Ratio More than 52dB (AGC OFF)
Gamma 0.45
Video Output VBS 1.0 Vp-p (75 ohm Load)
Sync. System Internal / External
Lens
BackLight
AGC
SENSE-UP
3D_DNR
COLOR
DAY&NIGHT
Function
MOTION
PRIVACY
SET
Dimension & Weight 120mm x 109mm, About 0.62Kg
AUTO/COLOR/BW
MIRROR/SHARPPNESS/GAMMA/SLC/NIGHT UP
4 areas
MASK1~MASK8
TITLE/DPC/MONITOR/LANGUAGE/OSD COLOR
COMMUNICATION/FACTORY SET
DC / VIDEO / MANUAL
OFF/SMART/HME/D-WDR
HIGHEST/HIGH/MIDDLE/LOW/OFF
X2 - X1024
OFF/LOW/MID/HIGH/SMART
AWC/ATW/MANUAL/PUSH LOCK
■
Specification
31
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Costar CDC3128VTIR Owner's manual

Costar
Brand
Costar
Model
CDC3128VTIR
Category
Security cameras
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents